Low Resistance Research Articles

Sputter Deposited Crystalline MoO2 Films as a High-Capacity and Stable Electrode Material for Supercapacitors: Mechanistic/Electrochemical Insights

In this work, we have optimized and fabricated pristine molybdenum dioxide (MoO2) electrodes over the Silicon (Si) substrate and examined the impact of various ion-loaded aqueous electrolytes on their electrochemical behavior. The sputtered electrodes exhibited a high crystalline structure and a very low resistivity. These highly conductive electrodes were tested in three different aqueous electrolytes (acidic, neutral, and alkaline) to establish a relation between the electrode and the nature of the electrolyte to achieve optimal electrochemical performance and cyclability. The electrochemical kinetics showed that the charge storage mechanism was unique for all the electrolytes. The capacitive current was dominant in the neutral electrolyte, whereas it was diffusive dominant in alkaline and 70% capacitive in the acidic electrolyte. Our findings indicated that the MoO2@Si electrode exhibited superior electrochemical activity in an acidic electrolyte. The electrode showed a voltage window of 0.6 V with an areal capacity of 24 mF/cm2 at 0.1 V/s scan rate. Moreover, the electrode also demonstrated excellent cyclability and capacitance retention (∼145%) till 5000 cycles. These results highlighted that the binder-free MoO2@Si electrode showed outstanding electrochemical activity and stability, which makes it suitable for sulfuric acid electrolyte-based energy storage systems.

Effect of Cetyl Trimethyl ammonium bromide (CTAB) amount on the Nanoindentation creep behaviour of Sn-cu-Y2O3 nanocomposite Lead-free solder

Sn-Cu-Y2O3 nanocomposite solder is synthesized from a citrate bath by pulse electrodeposition route. Y2O3 powder is synthesized from a sol-gel assisted combustion route. Different techniques such as SEM, XRD, and TEM are used to characterize Y2O3 powder. The particle size of Y2O3 powder is found to be 27 nm. The effect of adding cetyl trimethyl ammonium bromide (CTAB) on the synthesis of Sn-Cu-Y2O3 nanocomposite lead-free solder is studied. The amount of CTAB is varied for a particular amount of Y2O3 powder. It is carried out to find the exact ratio of CTAB for better dispersion of Y2O3 powder in the electrolytic bath. Because the distribution of reinforcement in the matrix which is associated with the dispersion of Y2O3 powder in the electrolyte is as important as the amount of reinforcement in the solder matrix. For the synthesis of nanocomposite solder, the optimum ratio of CTAB to Y2O3 is found to be 1:1. After the synthesis of nanocomposite solder, the influence of Y2O3 powder on the melting temperature of the solder is also studied. Incorporating Y2O3 has little effect on the melting point of the nanocomposite solder. Nanoindentation creep test results showed that the deposit at 0.2 A/cm2 (monolithic solder) has a lower creep resistance than the nanocomposite solders. Additionally, the creep resistance of the nanocomposite with a CTAB to Y2O3 ratio of 1:1 was higher.

Enhancing heat transfer performance of aluminum-based vapor chamber with a novel bionic wick structure fabricated using additive manufacturing

Given the lightweight nature and excellent thermal conductivity of aluminum, it offers significant potential for light-weighting of phase-change cooling components. To further enhance the thermal performance of aluminum-based vapor chambers, this study utilized selective laser melting (SLM) to design and integrally manufacture the slightly oleophilic wick for the condenser of the aluminum-based vapor chamber, along with three different superoleophilic wick structures for the evaporator: the gyroid bionic composite porous wick vapor chamber (GBCPVC), the groove composite porous wick vapor chamber (GCPVC), and the uniform porous wick vapor chamber (UPVC). A water-cooling experimental setup was established, and the effects of wick structure, cooling water flow rate, and cooling water temperature on the maximum heat load, temperature uniformity, and thermal resistance of vapor chambers were systematically investigated. The results indicated that the gyroid bionic porous wick structure significantly enhanced the thermal performance of the vapor chamber. Under the same conditions, GBCPVC exhibited lower thermal resistance and superior temperature uniformity, achieving a higher heat load than GCPVC and UPVC. When the cooling water temperature was decreased, its maximum heat load significantly increased. Specifically, at 15 °C, the maximum heat load for GBCPVC reached 300 W, an increase of 33.33 % and 53.33 % compared to 25 °C and 35 °C, respectively. Conversely, a rise in cooling water temperature enhanced the temperature uniformity and reduced thermal resistance of CBCPVC. At 35 °C and a heat load of 120 W, GBCPVC achieved a minimum thermal resistance of 0.034 K/W and a maximum temperature difference of 1.46 °C. Additionally, an increased flow rate enhanced the maximum heat load of GBCPVC, and under high heat loads, it could also reduce the thermal resistance and improve temperature uniformity. This study provides new insights and solutions for the thermal management of phase-change cooling components in aerospace electronic devices.

Experimental and numerical investigation on heat transfer analysis of square slotted pin-fin heat sinks

This paper introduces two novel designs of pin-fin heat sink (PHFS), namely the inline slotted pin-fin (ISP) and the V-shaped slotted pin-fin (VSP), to address rapid heat dissipation for one central/graphics processing unit (CPU/GPU) in a single-phase liquid cooling system. Experimental and numerical investigations are conducted to observe the effect of heat transfer for non-slotted and slotted pin-fin heat sinks under different Reynolds numbers (225-720) and heating powers (90-120 W). Parameters such as average wall temperature, Nusselt number, thermal resistance, pressure drop, and hydrothermal performance factor are evaluated. Comparative analyses show that the slotted pin-fin heat sinks exhibit higher Nusselt numbers (Nu) and lower thermal resistance (Rth) levels than that in the non-slotted pin-fin heat sinks, particularly at lower Reynolds numbers. At the Reynolds number 225 and power of 120 W, the inline and V-shaped slotted pin-fin heat sinks experience a 13.98% and 19.69% increase in Nu and a 12.65% and 15.41% reduction in Rth compared to the non-slotted one, respectively. The V-shaped slotted pin-fin heat sink achieves more than 5 ∘C reduction in the maximum wall temperature than the non-slotted one. The slotted structure reduces pressure drop losses by minimizing dead flow areas on one hand. On the other hand, the inclined slots generate vortices behind the fins, increase shear-induced mixing and thus improve the force convection cooling performance.

23.6 % Efficient perovskite-organic tandem photovoltaics enabled by recombination layer engineering

Recombination layers are crucial in achieving high power conversion efficiency (PCE) in tandem solar cells. Here, we report the development and optimization of recombination junctions for high PCE perovskite-organic tandem solar cells (PO-TSCs). We choose a wide bandgap perovskite (1.79 eV) for the front subcell and a narrow bandgap (1.36 eV) organic bulk heterojunction (BHJ) for the rear subcell. The optimal thicknesses of the perovskite and organic layers were determined to be 260 and 100 nm, respectively, based on the analysis of Transfer-Matrix optical simulations. Our results demonstrate that the optimal recombination layer consists of an ultrathin layer of indium zinc oxide IZO (∼ 2 nm) deposited on MoOx/2PACz, which delivers a PCE of 23.6 %. This high PCE is attributed to the high transparency of the recombination layer in the NIR spectra region and the low sheet resistance of IZO. Furthermore, we provide a theoretical analysis of the potential efficiency of PO-TSCs as a function of front and rear subcells and predict a maximum theoretical PCE value of more than 36 %. Our work highlights the importance of selecting the proper recombination layer design for achieving high-performance PO-TSCs.

Spray freeze dried cannabidiol with dipalmitoylphosphatidylcholine (DPPC) for inhalation and solubility enhancement

Pulmonary delivery is an efficient route of administration to deliver cannabidiol (CBD) due to the high bioavailability and fast onset of action. The major formulation challenge is the poor aqueous solubility of CBD. This study aimed to produce inhalable CBD powders with enhanced solubility and characterise their solid-state properties. CBD was spray freeze dried with mannitol or trehalose dihydrate with and without dipalmitoylphosphatidylcholine (DPPC). All four powders had acceptable yields at > 70 % with porous and spherical particles. The two crystalline mannitol powders contained less residual solvent than both amorphous trehalose ones. The addition of DPPC did not affect the crystallinity and residual solvent level of the powders. Instead, DPPC made the particles more porous, decreased the particle size from 19-23 µm to 11–13 µm, and increased CBD solubility from 0.36 µg/mL to over 2 µg/mL. The two DPPC powders were dispersed from a low resistance RS01 inhaler, showing acceptable aerosol performance with emitted fractions at 91–93 % and fine particle fractions < 5 µm at 34–43 %. These formulations can be used as a platform to deliver CBD and other cannabinoids by inhalation

The burden of lymphatic filariasis and its control strategies in Sierra Leone: A literature review

Lymphatic filariasis (LF) poses a significant health burden in Sierra Leone, with considerable socio-economic implications. LF, caused by parasitic worms transmitted through mosquito bites, leads to lymphedema, elephantiasis, and hydrocele, severely affecting individuals’ quality of life. Sierra Leone, with its tropical climate and inadequate healthcare infrastructure, faces unique challenges in combating lymphatic filariasis. This review explores the epidemiological landscape of LF in Sierra Leone, highlighting endemic regions, its impact, and control strategies. In 2005, epidemiological coverage of high-dose medications, like ivermectin and albendazole, exceeded 65% annually across 12 districts in Sierra Leone. By 2013, eight districts were eligible for transmission assessment surveys (TAS). After three additional rounds of mass drug administration (MDA), four districts became eligible for pre-TAS assessments in 2017. Despite efforts to control LF through mass drug administration (MDA) programs, challenges such as low treatment coverage, logistical constraints, and community resistance persist. Moreover, the impact of the Ebola outbreak on healthcare delivery has further impeded LF control efforts. This literature review adds to our understanding of LF control in Sierra Leone, providing valuable insights into the epidemiology, impact, challenges, and potential strategies for enhancing LF elimination efforts. It contributes to the broader discourse on neglected tropical diseases and public health interventions, emphasizing the need for context-specific approaches and interdisciplinary collaboration to achieve sustained progress towards LF elimination and improves public health outcomes.

The biphasic activity of autophagy and heat shock protein response in peripheral blood mononuclear cells following acute resistance exercise in resistance-trained males.

Autophagy and heat shock protein (HSP) response are proteostatic systems involved in the acute and adaptive responses to exercise. These systems may upregulate sequentially following cellular stress including acute exercise, however, currently few data exist in humans. This study investigated the autophagic and HSP responses to acute intense lower body resistance exercise in peripheral blood mononuclear cells (PBMCs) with and without branched-chain amino acids (BCAA) supplementation. Twenty resistance-trained males (22.3 ± 1.5yr; 175.4 ± .7cm; 86.4 ± 15.6kg) performed about of intense lower body resistance exercise and markers of autophagy and HSP70 were measured immediately post- (IPE) and 2, 4, 24, 48, and 72h post-exercise. Prior to resistance exercise, 10 subjects were randomly assigned to BCAA supplementation of 0.22g/kg/d for 5days pre-exercise and up to 72h following exercise while the other 10 subjects consumed a placebo (PLCB). There were no difference in autophagy markers or HSP70 expression between BCAA and PLCB groups. LC3II protein expression was significantly lower 2 and 4h post-exercise compared to pre-exercise. LC3II: I ratio was not different at any time point compared to pre-exercise. Protein expression of p62 was lower IPE, 2, and 4h post-exercise and elevated 24h post-exercise. HSP70 expression was elevated 48 and 72h post-exercise. Autophagy and HSP70 are upregulated in PBMCs following intense resistance exercise with autophagy increasing initially post-exercise and HSP response in the latter period. Moreover, BCAA supplementation did not affect this response.

Achieving Exceptional Volumetric Desalination Capacity Using Compact MoS2 Nanolaminates.

Capacitive deionization (CDI) has emerged as a promising technology for freshwater recovery from low-salinity brackish water. It is still inapplicable in specific scenarios (e.g., households, islands, or offshore platforms) due to too low volumetric adsorption capacities. In this study, we report a high-density semi-metallic molybdenum disulfide (1T'-MoS2) electrode with compact architecture obtained by restacking of exfoliated nanosheets, which achieved high capacitance up to ∼277.5 F cm-3 under an ultrahigh scan rate of 1000mV s-1 with a lower charge-transfer resistance and nearly ten-fold higher electrochemical active surface area than the 2H-MoS2 electrode. Furthermore, 1T'-MoS2 electrode demonstrates exceptional volumetric desalination capacity of 65.1 mgNaCl cm-3 in CDI experiments. Ex-situ X-ray diffraction (XRD) reveal that the cation storage mechanism with the dynamic expansion of 1T'-MoS2 interlayer to accommodate cations such as Na+, K+, Ca2+, and Mg2+, which in turn enhances the capacity. Theoretical analysis unveils that 1T' phase is thermodynamically preferable over 2H phase, the ion hydration and channel confinement also play critical role in enhancing ion adsorption. Overall, this work provides a new method to design compact two-dimensional layered nanolaminates with high volumetric performance for CDI desalination. This article is protected by copyright. All rights reserved.

Studies of carrier transport mechanism in NiO/Ag/NiO transparent conducting electrode/ZnO metal-semiconductor-metal photodetectors.

Dielectric/metal/dielectric (DMD) multilayers as a transparent conducting electrode (TCE) have been developed to replace metals due to their high transparency and low sheet resistance. Nickel oxide (NiO) film with a high work function was used as a dielectric to form NiO/Ag/NiO (NAN) TCE, therefore a high barrier height between NAN/zinc oxide (ZnO) interface. In the study, NAN TCE was deposited on ZnO surface to fabricate metal-semiconductor-metal (MSM) photodetectors (PDs) and study its carrier transport mechanism. The NAN TCE has a low sheet resistance of 6.5 Ω/sq. and transmittance more than 40% in a 300-100 nm wavelength range. Such issues result in the figure-of-merit is higher (2.3 × 10-4 Ω-1) than that (2.5 × 10-7 Ω-1) of pure single NiO thin film. As compared to the conventional Au/ZnO MSM-PDs, the NAN/ZnO MSM-PDs demonstrates a lower leakage current as a result of Ni atoms diffusing into ZnO and passivating the defects. Due to the high work function of NiO, the NAN/ZnO interface exhibits a barrier height as high as 0.91 eV. The Au/ZnO MSM-PDs reveals only one carrier conduction of ohmic due to the electrons tunnel form Au into ZnO through the surface defects. In contrast, two distinct carrier transport mechanisms were observed in the NAN/ZnO MSM-PDs. At low-voltage for, ohmic conduction dominates and the electrons inject from NAN to ZnO, trapped by the defect states of ZnO. At high-voltage for, the trapped electrons acquire enough energy and emit from trap to conduction band, entering Poole-Frankel emission transport.&#xD.

C-ShipGen: a conditional guided diffusion model for parametric ship hull design

Ship design is a complex design process that may take a team of naval architects many years to complete. Improving the ship design process can lead to significant cost savings, while still delivering high-quality designs to customers. A new technology for ship hull design is diffusion models, a type of generative artificial intelligence. Prior work with diffusion models for ship hull design created high-quality ship hulls with reduced drag and larger displaced volumes. However, the work could not generate hulls that meet specific design constraints. This paper proposes a conditional diffusion model that generates hull designs given specific constraints, such as the desired principal dimensions of the hull. In addition, this diffusion model leverages the gradients from a total resistance regression model to create low-resistance designs. Five design test cases compared the diffusion model to a design optimization algorithm to create hull designs with low resistance. In all five test cases, the diffusion model was shown to create diverse designs with a total resistance less than the optimized hull, having resistance reductions over 25%. The diffusion model also generated these designs without retraining. This work can significantly reduce the design cycle time of ships by creating high-quality hulls that meet user requirements with a data-driven approach.

Schottky junction-mediated carrier separation in BiOBr/Ti3C2Tx van der Waals heterojunction photocatalyst for increased removal of Cr(VI) under visible-light

The photocatalytic removal of pollutants can integrate efficient solar energy utilization with wastewater treatment. Herein, we report a simple strategy to construct BiOBr/Ti3C2Tx composite photocatalysts consisting of self-assembled van der Waals (vdw) heterojunction structures containing Schottky junctions. The vdW interaction between BiOBr and Ti3C2Tx and the structural stability of the catalysts were validated by density functional theory (DFT) calculations and an ab initio molecular dynamic simulation (AIMD). Compared to BiOBr, the BiOBr/Ti3C2Tx composites exhibited an enhanced light absorption capability and photocurrent response, along with a lower carrier recombination rate and charge-transfer resistance. The BiOBr/Ti3C2Tx activity for the photoreduction of hexavalent chromium (Cr(VI)) under visible-light irradiation considerably surpassed that of the original BiOBr (53.9%). Using the BTC-0.8 catalyst (with a Ti3C2Tx: BiOBr mass ratio of 0.8%) optimal reduction efficiency (94.0%) for Cr(VI) with a reaction rate approximately 3.5 times that of pure BiOBr. The BTC-0.8 catalyst was viable over a wide pH range and maintained an 83.9% photoreduction rate after four cycling experiments. The exceptional photocatalytic ability of BiOBr/Ti3C2Tx was achieved because Ti3C2Tx served as an electron injection layer that separated photogenerated carriers. The Schottky junction constructed within the BiOBr/Ti3C2Tx vdW heterojunctions suppressed electron backflow, promoting carrier separation. The excellent photocatalytic performance and strong cyclic stability of BiOBr/Ti3C2Tx demonstrated the considerable application potential of this photocatalyst.

Flexible Ni‐Based Bimetallic Spinel Oxide (NiM2O4, M = Mn, Fe, Co) Electrodes for Supercapacitor Applications

Herein, the single‐phase Ni‐based bimetallic spinel oxide (NiM2O4, M = Mn, Fe, Co) nanoparticles are successfully synthesized by sol–gel method and coated on a carbon cloth substrate to form flexible electrodes for supercapacitor applications. The effects of transition metal activity, calcination temperature, surface, and textural properties on the electrochemical properties of spinel electrode materials are demonstrated. It is found that lowering the calcination temperature results in a decrease in crystallite size and particle size, leading to an increase in surface area and pore volume. X‐Ray absorption spectroscopy reveals the presence of Mn2+/3+, Fe2+/3+, and Co2+/3+ in materials. According to the electrochemical studies, NiMn2O4 electrode in Na2SO4 electrolyte exhibits electrical double‐layer capacitance behavior, while NiFe2O4 and NiCo2O4 electrodes in KOH electrolyte exhibit pseudocapacitive behavior. All electrode materials have low solution resistance and charge transfer resistance. NiCo2O4 provides the highest specific capacitance (85.60 F g−1 at 2.5 A g−1) followed by NiFe2O4 and NiMn2O4. It seems likely that the high electrochemical activity of Co2+/3+ and small particle size of NiCo2O4 nanoparticles play an important role in improving the redox process and charge transfer, which may enhance the electrochemical performance of this electrode material.

Delineation of aquifer storage potential in response to regional groundwater development

Developing aquifers as part of sustainability efforts toward groundwater development is a tactical approach to meeting water demand and management objectives. Delineation of aquifer storage potential (ASP) and longitudinal conductance (SL\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${S}_{L}$$\\end{document}) is a good approach to protect and manage groundwater resources. A Schlumberger configuration was applied to delineate fifteen (15) vertical electrical sounding (VES) stations alongside a 2D electrical resistivity imagery (ERI) profile and regional borehole data to characterize the regional ASP. The results of the study show that the layer resistivity and thickness values of the regional aquifer unit range from 39.9–105 Ωm and 15–44 m, respectively, while the overburden thickness overlays the regional aquifer unit varied between 5–10 m corresponding to the regional borehole data. The weathered/fractured basemen, which constitute the regional aquifer unit were delineated, which consists of shallow, moderate, and deep aquifer zones. The deep aquifer zones fall within the depth of 30–44 m and are considered suitable for groundwater prospective. The weathered layer with appreciably low resistivity values with thick aquifer regolith has also been identified as most suitable for borehole siting. The weathered/fractured encountered within thick aquifer regolith were mapped as the region with a high ASP for groundwater development. In addition, the values of longitudinal conductance, SL\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${S}_{L}$$\\end{document} and transverse resistance, RT\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${R}_{T}$$\\end{document} estimated from aquifer parameters vary between 0.21-0.85Ω-1\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$0.21-0.85 \\,{\\Omega }^{-1}$$\\end{document} and 1695-3124Ωm2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$1695-3124\\, {\\Omega m}^{2}$$\\end{document}, respectively. The SL\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${S}_{L}$$\\end{document} values show that the study area falls within moderate (0.20-0.69Ω-1\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$0.20-0.69 \\,{\\Omega }^{-1}$$\\end{document}) and good (0.7-4.9Ω-1\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$0.7-4.9 \\,{\\Omega }^{-1}$$\\end{document}), which invariably determined the regional aquifer protective capacity. Thus, the DC geoelectrical approach has been successfully employed in a lateritic-based environment to delineate aquifer-promising zones for regional groundwater development.

Electrochemical study and structural comparison of Ni electrodepositions on W/Si and Cr/C multilayered structure films

Abstract The Ni electrodeposition combined with multilayered structure film is a promising strategy in modern optical manufacturing, while less effort has been devoted to comprehending the electrochemical reaction process, which is essential for their practical applications. In view of this, the initial reduction dynamics and nucleation mechanisms of Ni electrodepositions on multilayer W/Si and Cr/C films were analyzed in this work, and the morphological, crystal, and mechanical characteristics of produced Ni electrodeposits were further determined and compared. The results show that the considerably irregular crystals accompanied by high tensile stress of 119.5 MPa were formed for the Ni electrodeposit on W/Si film, which were mainly attributed to the progressive nucleation process with more severe side reaction of hydrogen evolution. By contrast, the instantaneous nucleation mode with lower reduction resistance were revealed for the Ni electrodeposition on Cr/C film, which presented a comparatively fine–grained texture, less roughness, and smaller stress structure. To summarize, the more stable electrochemical reaction process and improved structure uniformity are obtained for the Ni electrodeposition on metal/C–based film, which offers a theoretical guidance for optimized fabrication of multilayer optical devices in extreme ultraviolet, X–ray, and neutron focusing fields.

Compositional alteration of low dimensional nickel sulfides under hydrogen evolution reaction conditions in alkaline media

Developing cost-effective electrodes for electrochemical water splitting with minimal kinetic losses remains a primary challenge in water electrolysis. Nickel-based dichalcogenides, particularly sulfides, have emerged as promising candidates for the hydrogen evolution reaction (HER). However, the stability of various nickel sulfide (NixSy) phases under cathodic potentials in alkaline electrolytes is subject to debate. In this study, we investigate the HER activity and durability of both 2-dimensional (2D) and 3-dimensional (3D) NixSy nanostructures with diverse chemical compositions. Through cross-correlation analysis of spectroscopic and electrochemical characterization data, we elucidate the transformation behavior of these materials under operating conditions. Our findings reveal that NiS2 tends to undergo conversion to nickel hydroxide (Ni(OH)2), while Ni-rich phases like Ni3S4 and NiS exhibit greater stability. Furthermore, we demonstrate that in 3D nanostructures, the initial formation of a protective hydroxide layer on the surface inhibits further sulfide transformation. This nickel sulfide/hydroxide composite shows an improved HER activity with lower onset potential (−0.25 V), Tafel slope (105 mV s−1), and charge transfer resistance (17.3 Ω).

Enhanced optical and electrochemical properties of FeBTC MOF modified TiO2 photoanode for DSSCs application

In this work, iron based 1, 3, 5-tricarboxylic acid (FeBTC) was prepared via microwave-assisted method and incorporated into TiO2 via ultrasonic assisted method. The TiO2–FeBTC nanocomposites were characterized by XRD, FTIR, Raman, BET, FESEM, HRTEM, TGA, UV‒vis DRS and PL to understand their crystallographic, surface morphology, and optical characteristics. The Raman spectra showed a blue shift of Eg, A1g, and B1g peaks upon incorporation of FeBTC MOF onto TiO2. HRTEM and XRD analysis confirmed a mixture of TiO2 nanospheres and hexagonal FeBTC MOF morphologies with high crystallinity. The incorporation of FeBTC onto TiO2 improved the surface area as confirmed by BET results, which resulted in improved absorption in the visible region as a results of reduced bandgap energy from 3.2 to 2.84 eV. The PL results showed a reduced intensity for TiO2–FeBTC (6%) sample, indicating improved separation of electron hole pairs and reduced recombination rate. After fabrication of the TiO2–FeBTC MOF photoanode, the charge transfer kinetics were enhanced at TiO2–FeBTC MOF (6%) with Rp value of 966 Ω, as given by EIS studies. This led to high performance due to low charge resistance. Hence, high power conversion efficiency (PCE) value of 0.538% for TiO2–FeBTC (6%) was achieved, in comparison with other loadings. This was attributed to a relatively high surface area which allowed more charge shuttling and thus better electrical response. Conversely, upon increasing the FeBTC MOF loading to 8%, significant reduction in efficiency (0.478%) was obtained, which was attributed to sluggish charge transfer and fast electron–hole pair recombination rate. The TiO2–FeBTC (6%) may be a good candidate for use in DSSCs as a photoanode materials for improved efficiency.

Dual-targeted delivery of temozolomide by multi-responsive nanoplatform via tumor microenvironment modulation for overcoming drug resistance to treat glioblastoma.

Glioblastoma (GBM) is the most aggressive primary brain tumor with low survival rate. Currently, temozolomide (TMZ) is the first-line drug for GBM treatment of which efficacy is unfortunately hindered by short circulation time and drug resistance associated to hypoxia and redox tumor microenvironment. Herein, a dual-targeted and multi-responsive nanoplatform is developed by loading TMZ in hollow manganese dioxide nanoparticles functionalized by polydopamine and targeting ligands RAP12 for photothermal and receptor-mediated dual-targeted delivery, respectively. After accumulated in GBM tumor site, the nanoplatform could respond to tumor microenvironment and simultaneously release manganese ion (Mn2+), oxygen (O2) and TMZ. The hypoxia alleviation via O2 production, the redox balance disruption via glutathione consumption and the reactive oxygen species generation, together would down-regulate the expression of O6-methylguanine-DNA methyltransferase under TMZ medication, which is considered as the key to drug resistance. These strategies could synergistically alleviate hypoxia microenvironment and overcome TMZ resistance, further enhancing the anti-tumor effect of chemotherapy/chemodynamic therapy against GBM. Additionally, the released Mn2+ could also be utilized as a magnetic resonance imaging contrast agent for monitoring treatment efficiency. Our study demonstrated that this nanoplatform provides an alternative approach to the challenges including low delivery efficiency and drug resistance of chemotherapeutics, which eventually appears to be a potential avenue in GBM treatment.

Mesoporous Pdx-Nix aerogels for electrocatalytic evaluation of urea-assisted electrolysis

AbstractThis work presents the synthesis and evaluation of Pd-Ni aerogels toward the urea oxidation reaction (UOR). The incorporation of Ni led to a 0.13 V reduction in the energy required for the oxidation and reduction of PdO compared to monometallic Pd, both in alkaline medium with and without urea. Varying the Ni ratios in Pd (Pd-Ni 4:1, Pd-Ni 1:1, and Pd-Ni 1:4) led to significant changes in the electrochemical behaviour. In alkaline medium without urea, PdNi 4:1 showed the formation of NiOOH at 1.35 V, which promoted oxygen diffusion on the electrode surface and increased the current density, confirming the increase in the active sites of NiOOH and NiPdOOH and enabling urea-based electrolysis at these sites. While palladium aerogels alone are ineffective for UOR, the presence of nickel plays a key role in enhancing the UOR efficiency. On the other hand, physicochemical characterisation revealed that PdNi 4:1 has a crystal size of 4.37 nm and a larger shift in the 2θ positions of the (111) and (200) planes, which favours electronic changes that were investigated by XPS. These changes affected the electrocatalytic activity, which is primarily related to electronic effects. The results of SEM and TEM studies and nitrogen adsorption-desorption isotherm confirmed that the aerogels are highly porous and have an effective surface area and abundant active sites for reactions that allow efficient mass transfer and low diffusion resistance. TEM observations revealed interconnected nanochains indicating optimal electrocatalytic activity for both ORR and UOR due to high mass transfer. These interconnected networks are crucial for improving electrocatalytic activity in the urea oxidation reaction.

Engineering Porous Carbon with Precise Sizes to Promote Surface‐Dominated Storage in Sodium‐Ion Batteries

AbstractAs the sole commercially viable anode material for sodium‐ion batteries, hard carbon currently faces challenges such as slow diffusion kinetics in the low voltage range and low safety due to sodium deposition. In order to deepen the understanding of the pseudocapacitive processes of hard carbon in the high voltage range and enhance sodium storage capacity, this study systematically investigates the electrochemical performance and ion storage of ZIF‐8‐derived porous carbons (ZPCs) of different sizes. We propose a mathematical model based on a spherical particle core‐shell structure, which profoundly reveals the relationship between size and specific surface area, as well as the linear relationship between specific surface area and specific capacity. Moreover, simply by reducing the size of the porous carbon, the specific capacity increased by 86.5 mAh g−1. Dynamic studies reveal that in nano‐porous carbon materials, sodium‐ion storage primarily relies on defect adsorption. Size reduction enhances physical adsorption and surface capacitance response, with ZPC‐80 exhibiting lower resistance and higher diffusion coefficient, indicating that size reduction improves electronic conductivity and charge transfer efficiency, achieving excellent reversible capacity and cycling stability. This work yields a profound insight into the dynamic characteristics of hard carbon anode materials, presenting a new perspective for the design of efficient sodium‐ion batteries.