Low Line Current Harmonic Distortion Research Articles

Analysis and Design of a DC-Side Symmetrical Class-D ZCS Rectifier for the PFC of Lighting Applications

This paper proposes the analysis and design of a DC-side symmetrical zero-current-switching (ZCS) Class-D current-source driven resonant rectifier to improve the low power-factor and high line current harmonic distortion of lighting applications. An analysis of the junction capacitance effect of Class-D ZCS rectifier diodes, which has a significant impact on line current harmonic distortion, is discussed in this paper. The design procedure is based on the principle of the symmetrical Class-D ZCS rectifier, which ensures more accurate results and provides a more systematic and feasible analysis methodology. Improvement in the power quality is achieved by using the output characteristics of the DC-side Class-D ZCS rectifier, which is inserted between the front-end bridge-rectifier and the bulk-filter capacitor. By using this symmetrical topology, the conduction angle of the bridge-rectifier diode current is increased and the low line harmonic distortion and power-factor near unity were naturally achieved. The peak and ripple values of the line current are also reduced, which allows for a reduced filter-inductor volume of the electromagnetic interference (EMI) filter. In addition, low-cost standard-recovery diodes can be employed as a bridge-rectifier. The validity of the theoretical analysis is confirmed by simulation and experimental results.

A Comparative Performance Investigation of Single-Stage Dimmable Electronic Ballasts for Electrodeless Fluorescent Lamp Applications

This paper presents a comparative investigation, design and development issues about six different single-stage topologies, applied as electronic ballasts, for electrodeless fluorescent lamps. The ballast is intended to feed a 100 W lamp at 250 kHz, with dimming feature. The proposed topologies use different converters for the power factor correction (PFC) stage: Buck-Boost, SEPIC, Zeta, Cúk, Flyback, and Boost. All of them operate in discontinuous conduction mode. A resonant half-bridge inverter is used as lamp power control (PC) stage. The integration of both stages (PFC and PC) is proposed in this paper. In this way, it is possible to reduce the number of active switches, as well as simplify the required driving and control circuitry. Experimental results demonstrate the feasibility of the proposed dimming technique that achieved around 56% lamp power dimming, from 100 W down to 44 W. The implemented topologies attained high average power factor (>0.98), and low line current average total harmonic distortion (<;15.3%). A comparison among all the proposed topologies in terms of power factor, harmonic distortion, efficiency and number of components is presented. Finally, a comparison between an integrated and a nonintegrated SEPIC half-bridge converter is also performed.

A high-frequency-transformer-isolated two-switch three-phase ac-to-dc converter with low harmonic distortion

This paper presents a high-frequency-transformer-isolated, single-stage, fixed-frequency, soft-switching, three-phase ac-to-dc converter with low line-current harmonic distortion. The converter uses only two switches and a simple control circuit without any active control scheme. Various operating modes of the converter are presented and analyzed. Based on the analysis, design curves are obtained and a design example is presented. The performance of the proposed converter is evaluated using PSPICE simulation and a laboratory prototype with 500 W output (using IGBTs as switching devices).

A Novel Soft-Switching High-Frequency Transformer Isolated Three-Phase AC-to-DC Converter With Low Harmonic Distortion

A high-frequency transformer isolated, fixed-frequency, 3-/spl phi/ single-stage ac-to-dc converter using a boost-integrated bridge converter that employs a new gating scheme is proposed. This converter enjoys natural power factor correction with low line current harmonic distortion and symmetric high frequency voltage and current waveforms while ensuring zero-voltage switching for all the switches for a wide variation in load and line voltage. Various operating modes of the converter are presented and analyzed. Based on the analysis, design curves are obtained and an optimum design is given. A design example is presented. Results obtained from SPICE simulation and a 500 W output experimental prototype are given to verify the performance of the proposed converter for varying load as well as line voltage.

Single-phase power-factor-correction AC/DC converters with three PWM control schemes

Three pulse-width modulation (PWM) control schemes for a single-phase power-factor-correction (PFC) AC/DC converter are presented to improve the power quality. A diode bridge with two power switches is employed as a PFC circuit to achieve a high power factor and low line current harmonic distortion. The control schemes are based on look-up tables with hysteresis current controller (HCC) to generate two-level or three-level PWM on the DC side of diode rectifier. Based on the proposed three control schemes, the line current is driven to follow the sinusoidal current command which is in phase with the supply voltage, and two capacitor voltages on the DC bus are controlled to be balanced. The simulation and experimental results of a 1 kW converter with load as well as line voltage variation and shown to verify the proposed control schemes. It is shown that unity PFC is achieved using a simple control circuit and the measured line current harmonics satisfy the IEC 1000-3-2 requirements.

Soft-switching single-stage AC-to-DC converter with low harmonic distortion

A 1 /spl phi/ high-frequency (HF) transformer isolated, soft-switching single-stage ac-dc converter with low line-current harmonic distortion is presented. Its operation is explained with equivalent circuits for the various intervals. The converter is analyzed and design curves are obtained. An optimization parameter is introduced and a systematic design procedure is illustrated with a design example. Detailed SPICE simulation and experimental results of a 500 W converter with load as well as line voltage variation are given to verify theory. The proposed converter employs a zero-voltage transition (ZVT) network to ensure zero-voltage switching (ZVS) at all loads, and natural power factor correction is ensured using a simple control circuit.

Operation of the LCC-type parallel resonant converter as a low harmonic rectifier

A single-phase high-frequency transformer isolated single-stage AC-to-DC controlled rectifier with low line current harmonic distortion using a variable-frequency controlled LCC-type (or series-parallel) resonant power converter (SPRC) is presented. A simple analysis and design procedure is used for designing the converter for low line current harmonic distortion and high power factor operation. The converter performance characteristics have been verified with SPICE3 simulations (without active control) and experimental prototype SPRC (rated at 150 W, with and without active control) for variation in load as well as line voltage. When operated with active current shaping, this converter operates in zero-voltage-switching mode for the complete range, maintaining power factor close to unity with low line current distortion and low peak current compared to the parallel resonant converter.

Integrated ZCS quasi-resonant single-stage highpower factor converter

A new single phase zero-current-switched (ZCS) single stage quasi-resonant converter (QRC) for power factor correction (PFC) is proposed. The converter provides a good power factor, has tight output regulation, and low line current harmonic distortion. The proposed converter is suitable for low power level power supplies with high efficiency and tightly regulated output voltage.

Characteristics of a fixed-frequency series-parallel resonant converter operating on the utility line with and without active control

A single-phase high-frequency transformer-isolated ac-to-dc controlled rectifier using a fixed-frequency series-parallel (or LCC-type) resonant converter (SPRC) is presented. A simple analysis and design procedure is used for designing the converter for low line-current harmonic distortion and high power-factor (PF) operation. The converter performance characteristics have been verified with SPICE simulations and an experimental prototype SPRC, without using active control. These results show that, although no active control is used, the converter operates with a line-current total harmonic distortion (THD) of 13.5% at full load and 23.6% at half load, with line PF > 0.97. Active control has also been implemented in the experimental prototype to achieve a line PF > 0.99 with a THD of < 16%, for variation in supply voltage and load (full load to half load).