Low-frequency Synthetic Aperture Radar Research Articles

Snow water equivalent retrieval over Idaho – Part 2: Using L-band UAVSAR repeat-pass interferometry

Abstract. This study evaluates using interferometry on low-frequency synthetic aperture radar (SAR) images to monitor snow water equivalent (SWE) over seasonal and synoptic scales. We retrieved SWE changes from nine pairs of SAR images, mean 8 d temporal baseline, captured by an L-band aerial platform, NASA's Uninhabited Aerial Vehicle Synthetic Aperture Radar (UAVSAR), over central Idaho as part of the NASA SnowEx 2020 and 2021 campaigns. The retrieved SWE changes were compared against coincident in situ measurements (SNOTEL and snow pits from the SnowEx field campaign) and to 100 m gridded SnowModel modeled SWE changes. The comparison of in situ to retrieved measurements shows a strong Pearson correlation (R=0.80) and low RMSE (0.1 m, n=64) for snow depth change and similar results for SWE change (RMSE = 0.04 m, R=0.52, n=57). The comparison between retrieved SWE changes to SnowModel SWE change also showed good correlation (R=0.60, RMSD = 0.023 m, n=3.2×106) and especially high correlation for a subset of pixels with no modeled melt and low tree coverage (R=0.72, RMSD = 0.013 m, n=6.5×104). Finally, we bin the retrievals for a variety of factors and show decreasing correlation between the modeled and retrieved values for lower elevations, higher incidence angles, higher tree percentages and heights, and greater cumulative melt. This study builds on previous interferometry work by using a full winter season time series of L-band SAR images over a large spatial extent to evaluate the accuracy of SWE change retrievals against both in situ and modeled results and the controlling factors of the retrieval accuracy.

A Registration Method for Dual-Frequency, High-Spatial-Resolution SAR Images

With the continuous development of synthetic-aperture-radar (SAR) technology, SAR-image data are becoming increasingly abundant. For the same scene, dual-frequency (high-frequency and low-frequency) SAR images can present different details and feature information. Image fusion of the two frequencies can combine the advantages of both, thus describing targets more comprehensively. Image registration is the key step of image fusion and determines the quality of fusion. Due to the complex geometric distortion and gray variance between dual-frequency SAR images with high resolution, it is difficult to realize accurate registration between the two. In order to solve this problem, this paper proposes a method to achieve accurate registration by combining edge features and gray information. Firstly, this paper applies the edge features of images and a registration algorithm based on fast Fourier transform (FFT) to realize rapid coarse registration. Then, combining a registration algorithm based on the enhanced correlation coefficient (ECC) with the concept of segmentation, the coarse-registration result is registered to achieve accurate registration. Finally, by processing the airborne L-band and Ku-band SAR data, the correctness, effectiveness, and practicability of the proposed method are verified, with a root mean square error (RMSE) of less than 2.

Ionospheric Sounding Based on Spaceborne PolSAR in P-Band

The signal of spaceborne low-frequency full-polarization synthetic aperture radar (full-pol SAR) contains abundant ionospheric information. Phased Array L-band Synthetic Aperture Radar (PALSAR) working in the L-band has been verified as an emerging ionospheric sounding technology. Aiming for a future P-band SAR system, this paper investigates the ability of the P-band SAR system in ionospheric one-dimensional and two-dimensional detection. First, considering different systematic error levels, the total electron content (TEC) retrieval in L/P-band is studied by using three typical full-pol SAR data sets based on a circular polarization algorithm. Second, the TEC data retrieved by SAR are fused with the ionosonde, and the joint retrieval of ionospheric electron density is performed. Results show that the P-band TEC retrieval is approximately twice as accurate as the L-band retrieval under the same conditions, and possesses excellent robustness. In addition, the TEC obtained by L/P-band SAR can be used to correct the electron density of the topside on the ionosonde. Results also show that compared with the topside correction accuracy of L-band SAR, that of the P-band SAR is improved by more than 20%. SAR has natural high-resolution characteristics and the P-band signal contains more obvious ionospheric information than the L-band signal. Therefore, future spaceborne P-band SAR has many advantages in two-dimensional fine ionospheric observation and one-dimensional electron density retrieval.

Estimating Significant Wave Height from SAR with Long Integration Times

Synthetic aperture radar (SAR) is an important means of estimating significant wave height with obvious advantages of all-day, all-weather, high resolution and wide swath coverage. At present, the estimation methods of significant wave height are based on visible ocean waves in SAR images. However, due to the characteristic of long integration time for low-frequency SAR (such as P-band, L-band), the ocean waves are usually invisible in SAR images. In addition, in the case that there are multiple wave systems, significant wave height of only one wave system can be estimated for the reason that only a blurred wave system can be observed in SAR images. In order to solve the above two problems, a method of estimating significant wave height from SAR with long integration times is proposed in this paper. Firstly, each ocean wave system is refocused from single-look complex (SLC) data, respectively. Then, without any additional processing, the 180° ambiguity of wave propagation direction is removed based on the optimum focus setting. Finally, significant wave height is estimated in combination with azimuth cutoff, wavelength and propagation direction of ocean waves. This method is applied to two airborne SAR field data with long integration times. One case is that ocean waves are invisible in SAR images, the other is that there are two wave systems on the real ocean surface, but only one is visible in the SAR images. The results show that the proposed method can estimate significant wave height in the cases of invisible ocean waves and multiple ocean waves. The estimation results of significant wave height are compared with the European Centre for Medium-Range Weather Forecast (ECMWF) data, and the error is basically stable within 0.2 m, which verifies the effectiveness of the proposed method.

Tropical Forest Vertical Structure Characterization: From GEDI to P-Band SAR Tomography

Estimating tropical forests vertical structure using remote sensing is a challenge. Active sensors such as low-frequency Synthetic Aperture Radar (SAR) operating at P-band, with a wavelength of ~ 69 cm wavelength, and Light Detection and Ranging (LiDAR) are able to penetrate thick vegetation layers. While NASA’s Global Ecosystem Dynamics Investigation (GEDI) is collecting spaceborne liDAR data, the ESA’s next Earth Explorer BIOMASS mission will acquire multiple acquisitions over the same areas to form three-dimensional images through SAR tomography (TomoSAR) technique. Our study shows the potential value of GEDI and TomoSAR acquisitions in producing accurate estimates of forests vertical structure. By analyzing airborne P-band TomoSAR, airborne LiDAR, and spaceborne GEDI LiDAR at a tropical forest site in Paracou, French Guiana, South America, we show that both GEDI and P-band TomoSAR can directly measure surface, vegetation heights, and vertical profiles with high resolution and precision. Airborne TomoSAR is of higher quality than GEDI due to better penetration properties and precision. However, the GEDI vegetation height root-mean-square error is less than 5 m, for an average forest height value around 30 m at the Paracou site, which is similar to the expected performance of the future spaceborne BIOMASS mission. These results suggest GEDI measurements, i.e. shots with sensitivity greater than 98%, will provide a good reference of forest structure to calibrate the BIOMASS mission algorithms.

Autofocus-Based Estimation of Penetration Depth and Permittivity of Ice Volumes and Snow Using Single SAR Images

An intrinsic challenge in the geophysical interpretation of low-frequency synthetic aperture radar (SAR) imagery of semitransparent media, such as ice sheets, is the position ambiguity of the scattering structures within the glacial volume. Commonly tackled by applying interferometric and tomographic techniques, their spaceborne implementation exhibits by orders higher complexity compared to missions relying on single SAR images, making them cost expensive or, in the context of planetary missions, even impossible due to limited navigation capability. Besides, even these sophisticated techniques are commonly biased due to inaccurate permittivity estimates, leading to geometric distortions up to several meters. We present a novel inversion procedure to estimate volume parameters of ice sheets, namely, the depth of the scattering layer within the glacial volume and the dielectric permittivity of the ice, based on single-image single-polarization SAR acquisitions. The information is inherent in the processed SAR data as phase errors on the azimuth signals resulting from uncompensated nonlinear propagation of the radar echoes through ice. We suggest a local map-drift autofocus approach to quantify and spatially resolve the phase errors and an inversion model to relate them to the penetration depth and permittivity. Testing the proposed technique using P-band SAR data acquired using DLR’s airborne sensor F-SAR during the ARCTIC15 campaign in Greenland shows promising results and good agreement with tomographic products of the analyzed test site.

Potential of P-Band SAR Tomography in Forest Type Classification

Forest type classification using spaceborne remote sensing is a challenge. Low-frequency Synthetic Aperture Radar (SAR) signals (i.e., P-band, ∼0.69 m wavelength) are needed to penetrate a thick vegetation layer. However, this measurement alone does not guarantee a good performance in forest classification tasks. SAR tomography, a technique employing multiple acquisitions over the same areas to form a three-dimensional image, has been demonstrated to improve SAR’s capability in many applications. Our study shows the potential value of SAR tomography acquisitions to improve forest classification. By using P-band tomographic SAR data from the German Aerospace Center F-SAR sensor during the AfriSAR campaign in February 2016, the vertical profiles of five different forest types at a tropical forest site in Mondah, Gabon (South Africa) were analyzed and exploited for the classification task. We demonstrated that the high sensitivity of SAR tomography to forest vertical structure enables the improvement of classification performance by up to 33%. Interestingly, by using the standard Random Forest technique, we found that the ground (i.e., at 5–10 m) and volume layers (i.e., 20–40 m) play an important role in identifying the forest type. Together, these results suggested the promise of the TomoSAR technique for mapping forest types with high accuracy in tropical areas and could provide strong support for the next Earth Explorer BIOMASS spaceborne mission which will collect P-band tomographic SAR data.

Measuring Ionospheric Scintillation Parameters From SAR Images Using Phase Gradient Autofocus: A Case Study

The spaceborne low-frequency (L-band and below) synthetic aperture radar (SAR) is very susceptible to ionospheric scintillation. The scintillation phase error (SPE) is a vital factor that brings about the azimuth decorrelation and leads to the imaging degradation. In this article, a methodology is described, which exploits the accurate SPE estimation to measure scintillation parameters from SAR images. First, the phase gradient autofocus (PGA) is applied to achieve the believable SPE estimate from the local area that contains a strong scatterer. Second, based on the estimated staggered index of two SPE estimates, the irregularity altitude can be derived by solving an established equation using an iteration process. Third, three parameters, including the spectrum index, the outer scale, and the integrated turbulence strength, can be fitted when the theoretical spectrum expression mostly approximates the derived spectrum. The methodology is validated on an ALOS-2 PALSAR-2 spotlight data, and its azimuth imaging was seriously degraded by ionospheric scintillation. Two existent corner reflectors ensure the accuracy of SPE estimates from PGA. The measurement results indicate that the local ionospheric irregularities are extremely turbulent and located at a lower altitude of about 220 km in the F2-layer.

Translation between High- and Low-frequency SAR Images using Cycle-Consistent Conditional Adversarial Network

The bi-frequency (high- and low) synthetic aperture radar (SAR) images cannot be directly compared due to their distinct statistical properties. To diminish their statistical difference, we manage to translate the bi-frequency SAR images into one another. Therefore, we propose a cycle-consistent conditional adversarial network to achieve the goal. The cycle-consistency criteria in the Cycle GAN and the conditional generation adversarial networks in the Pix2Pix are integrated to construct the cycle-consistent conditional adversarial network. Experiments on Ku-band and P-band SAR images validate that our method outperforms Cycle GAN and Pix2Pix.

Correction of amplitude scintillation effect in fully polarimetric SAR coherency matrix data

In this paper, we investigate the correction of ionospheric amplitude scintillations appearing as image artifacts in low frequency synthetic aperture radar (SAR) data. A method has been proposed to separate amplitude and phase components of fully polarimetric SAR (POLSAR) coherency matrix [T], and then implement a combination of multi-level, two-dimensional Discrete Wavelet Transform and Fast Fourier Transform (DWT-FFT) to correct the amplitude scintillation-induced stripes in [T] matrix. In the methodology, [T] is decomposed into component matrices of amplitude and relative phases. To the amplitude [T] matrix, a combination of 2-D DWT is performed, using the Haar wavelet, followed by a non-linear 2-D FFT correction strategy to remove amplitude scintillation stripes. Using DWT, each amplitude [T] matrix element is decomposed into low- and high-frequency components known as approximate and detailed coefficients respectively. On applying a 2-D FFT on the detailed coefficients, amplitude scintillation-induced stripes are easily identified in the frequency spectrum and then removed using 2-D FFT correction strategy of averaging-post-thresholding. The proposed method is tested on the [T] matrix of several POLSAR datasets acquired from Advanced Land Observation Satellite/Phased Array type L-band synthetic aperture radar (ALOS/PALSAR) and Advanced Land Observation Satellite-2/Phased Array type L-band synthetic aperture radar-2 (ALOS-2/PALSAR-2) satellites. The performance of the correction technique is analysed both, qualitatively and quantitatively. While improvements in the post-correction datasets are visually observed, a supervised Wishart classification also performed on the [T] matrices of undisturbed (reference), disturbed and corrected data indicates significant increase in overall accuracy (OA) and kappa coefficient (k̂) parameters. The classification accuracies of the disturbed data (OA = 69.31%, k̂=0.54) improved to OA = 76.49%, k̂=0.68 after applying the proposed correction approach, which is comparable to the reference data values (OA = 81.57%, k̂=0.71). The proposed method performs significantly better than the existing technique of a simple 2-D FFT approach (OA = 73.49%, k̂=0.62). The contribution of dominant scattering powers, obtained from the seven-component scattering power decomposition of POLSAR coherency matrix (7SD) model, also demonstrates post-correction improvements. The dominant scattering power for targets increased by ~3–9% using the proposed approach, shows an improvement of ~3% over the existing 2-D FFT technique.

Performance Analysis of Autofocus Algorithms for Compensating Ionospheric Dispersion Effect on Spaceborne Low-Frequency SAR Focusing

Spaceborne low-frequency synthetic aperture radar with high resolution will be affected by ionospheric dispersion, which introduces a quadratic range phase error, leading to range defocusing. The dependence of the performance of contrast optimization (CO) autofocus and multilook registration (MLR) autofocus for dispersion compensation on the signal-to-clutter ratio (SCR) is analyzed. For SCR >20 dB, two autofocus algorithms have similar performances, and CO is a little better. For SCR <; 20 dB, CO, and MLR performance will be affected by initial quadratic phase error (QPE) and clutter size, respectively. When the initial QPE is less than 530°, and clutter size is at least 100 resolution cells, CO performance will be better than MLR. Taking 45° QPE as the threshold for accurate focusing, in the case of the single point object, the threshold SCR for CO to be effective is approximately between 12.5 and 18 dB, corresponding to initial QPE between 0° and 800°. For MLR, the threshold SCR is approximately between 17.5 and 18.5 dB, corresponding to clutter size between 100 and 500 resolution cells. For the case of multiple point objects, the threshold SCR values of both algorithms will decrease. Simulations based on scenes derived from PALSAR2 data demonstrate the effectiveness of the CO and MLR autofocus algorithm.

Improved POLSAR Model-Based Decomposition Interpretation Under Scintillation Conditions

Low-frequency synthetic aperture radar (SAR) sensors are prone to ionospheric irregularity structures that affect the amplitude and/or phase of the radar signal. Azimuthal striping caused by amplitude scintillation in SAR data is an initial observation of such effects. In the absence of any physical model and/or technique to mitigate scintillation stripes, we have applied a 2-D fast Fourier transform (FFT) approach for improved interpretation and target identification in fully polarimetric SAR (POLSAR) model-based decomposition scattering powers. Few scenes of fully polarimetric Advanced Land Observation Satellite-Phased Array type L-band Synthetic Aperture Radar (ALOS/PALSAR) and ALOS-2/PALSAR-2 under different ionospheric conditions are acquired and used in this study. As a reference, data sets over the same areas are also acquired on different dates with negligible ionospheric activity (ionospheric quiet day). All the data sets are corrected for the Faraday rotation angle ( $\Omega$ ), which is estimated using the Bickel–Bates approach. Three correction strategies of scintillation-affected model-based scattering power decomposition images are presented. The strategies (zero masking, thresholding, and averaging-post-thresholding) are implemented on 2-D FFT of scattering power images. An intercomparison of corrected decomposition results from the correction strategies demonstrates the capability of 2-D-FFT-based correction strategies to improve the dominant scattering component by 3%–5% for homogeneous terrains. The correction method based on averaging-post-thresholding gives the best results that are further tested by performing a supervised classification. The overall accuracy and kappa coefficient ( ${OA}, \hat {k}$ ) of the averaging-post-thresholding technique (72.87%, 0.59) is comparable to those of the reference data (78.74%, 0.69).

An Improved Generalized Chirp Scaling Algorithm Based on Lagrange Inversion Theorem for High-Resolution Low Frequency Synthetic Aperture Radar Imaging

The high-resolution low frequency synthetic aperture radar (SAR) has serious range-azimuth phase coupling due to the large bandwidth and long integration time. High-resolution SAR processing methods are necessary for focusing the raw data of such radar. The generalized chirp scaling algorithm (GCSA) is generally accepted as an attractive solution to focus SAR systems with low frequency, large bandwidth and wide beam bandwidth. However, as the bandwidth and/or beamwidth increase, the serious phase coupling limits the performance of the current GCSA and degrades the imaging quality. The degradation is mainly caused by two reasons: the residual high-order coupling phase and the non-negligible error introduced by the linear approximation of stationary phase point using the principle of stationary phase (POSP). According to the characteristics of a high-resolution low frequency SAR signal, this paper firstly presents a principle to determine the required order of range frequency. After compensating for the range-independent coupling phase above 3rd order, an improved GCSA based on Lagrange inversion theorem is analytically derived. The Lagrange inversion enables the high-order range-dependent coupling phase to be accurately compensated. Imaging results of P- and L-band SAR data demonstrate the excellent performance of the proposed algorithm compared to the existing GCSA. The image quality and focusing depth in range dimension are greatly improved. The improved method provides the possibility to efficiently process high-resolution low frequency SAR data with wide swath.

Comparison of the Rayleigh and K-Distributions for Application in Incoherent Change Detection

The aim of this letter is to compare two incoherent change-detection algorithms for target detection in low-frequency ultrawideband (UWB) synthetic aperture radar (SAR) images. The considered UWB SAR operates in the frequency range from 20 to 90 MHz. Both approaches employ a likelihood ratio test according to the Neyman–Pearson criterion. First, the bivariate Rayleigh probability distribution is used to implement the likelihood ratio test function. This distribution is well known and has been used for change-detection algorithms in low-frequency UWB SAR with good results. Aiming to minimize the false alarm rate and taking into consideration that low-frequency UWB SAR images have high resolution compared to the transmitted wavelength, the second approach implements the test by using a bivariate K-distribution. This distribution has scale and shape parameters that can be used to adjust it to the data. No filter is applied to the data set images, and the results show that with a good statistical model, it is not needed to rely on filtering the data to decrease the number of false alarms. Therefore, we can have a better tradeoff between resolution and detection performance.

Aboveground Forest Biomass Estimation Combining L- and P-Band SAR Acquisitions

While considerable research has focused on using either L-band or P-band SAR (Synthetic Aperture Radar) on their own for forest biomass retrieval, the use of the two bands simultaneously to improve forest biomass retrieval remains less explored. In this paper, we make use of L- and P-band airborne SAR and in situ data measured in the field together with laser scanning data acquired over one hemi-boreal (Remningstorp) and one boreal (Krycklan) forest study area in Sweden. We fit statistical models to different combinations of topographic-corrected SAR backscatter and forest heights estimated from PolInSAR for the biomass estimation, and evaluate retrieval performance in terms of R2 and using 10-fold cross-validation. The study shows that specific combinations of radar observables from L- and P-band lead to biomass predictions that are more accurate in comparison with single-band retrievals. The correlations and accuracies between the combinations of SAR features and aboveground biomass are consistent across the two study areas, whereas the retrieval performance varied for individual bands. P-band-based retrievals were more accurate than L-band for the hemi-boreal Remningstorp site and less accurate than L-band for the boreal Krycklan site. The aboveground biomass levels as well as the ground topography differ between the two sites. The results suggest that P-band is more sensitive to higher biomass and L-band to lower biomass forests. The forest height from PolInSAR improved the results at L-band in the higher biomass substantially, whereas no improvement was observed at P-band in both study areas. These results are relevant in the context of combining information over boreal forests from future low-frequency SAR missions such as the European Space Agency (ESA) BIOMASS mission, which will operate at P-band, and future L-band missions planned by several space agencies.

Analysis of the Regional Ionosphere at Low Latitudes in Support of the Biomass ESA Mission

Biomass is a spaceborn polarimetric P-band (435 MHz) synthetic aperture radar (SAR) in a dawn–dusk low Earth orbit. Its principal objective is to measure biomass content and change in all the Earth’s forests. The ionosphere introduces the Faraday rotation on every pulse emitted by low-frequency SAR and scintillations when the pulse traverses a region of plasma irregularities, consequently impacting the quality of the imaging. Some of these effects are due to total electron content (TEC) and its gradients along the propagation path. Therefore, an accurate assessment of the ionospheric morphology and dynamics is necessary to properly understand the impact on image quality, especially in the equatorial and tropical regions. To this scope, we have conducted an in-depth investigation of the significant noise budget introduced by the two crests of the equatorial ionospheric anomaly (EIA) over Brazil and Southeast Asia. This paper is characterized by a novel approach to conceive a SAR-oriented ionospheric assessment, aimed at detecting and identifying spatial and temporal TEC gradients, including scintillation effects and traveling ionospheric disturbances, by means of Global Navigation Satellite Systems ground-based monitoring stations. The novelty of this approach resides in the customization of the information about the impact of the ionosphere on SAR imaging as derived by local dense networks of ground instruments operating during the passes of Biomass spacecraft. The results identify the EIA crests as the regions hosting the bulk of irregularities potentially causing degradation on SAR imaging. Interesting insights about the local characteristics of low-latitudes ionosphere are also highlighted.

Research Pathways of Forest Above-Ground Biomass Estimation Based on SAR Backscatter and Interferometric SAR Observations

Estimation of forest biomass with synthetic aperture radar (SAR) and interferometric SAR (InSAR) observables has been surveyed in 186 peer-reviewed papers to identify major research pathways in terms of data used and retrieval models. Research evaluated primarily (i) L-band observations of SAR backscatter; and, (ii) single-image or multi-polarized retrieval schemes. The use of multi-temporal or multi-frequency data improved the biomass estimates when compared to single-image retrieval. Low frequency SAR backscatter contributed the most to the biomass estimates. Single-pass InSAR height was reported to be a more reliable predictor of biomass, overcoming the loss of sensitivity of SAR backscatter and coherence in high biomass forest. A variety of empirical and semi-empirical regression models relating biomass to the SAR observables were proposed. Semi-empirical models were mostly used for large-scale mapping because of the simple formulation and the robustness of the model parameters estimates to forest structure and environmental conditions. Non-parametric models were appraised for their capability to ingest multiple observations and perform accurate retrievals having a large number of training samples available. Some studies argued that estimating compartment biomass (in stems, branches, foliage) with different types of SAR observations would lead to an improved estimate of total biomass. Although promising, scientific evidence for such an assumption is still weak. The increased availability of free and open SAR observations from currently orbiting and forthcoming spaceborne SAR missions will foster studies on forest biomass retrieval. Approaches attempting to maximize the information content on biomass of individual data streams shall be pursued.

Low-Frequency SAR Radiometric Calibration and Antenna Pattern Estimation by Using Stable Point Targets

In this paper, the synthetic aperture radar (SAR) calibration for low-frequency missions by means of stable point targets is presented. Calibration at low frequency involves the absolute radiometric calibration, the antenna pattern and pointing characterization and validation, and the distortion system parameters’ estimation. The use of traditional instrumentation, such as a polarimetric active radar calibrator, a corner reflector, or an active transponder, may be costly and can reduce the time the instrument is used for operational acquisitions. The purpose of this paper is to evaluate the potentiality in calibration of point targets for which the radar cross section and the time stability have been characterized. Given a calibration site, once that a set of the stable point targets have been detected by the analysis of an interferometric stack of SAR acquisitions, they may be used as passive calibrators for the validation of radiometry, elevation antenna pattern, and pointing estimation. We show that, although less targets are expected to be found in P- or L- band than in C- or X-band, a sufficient amount (about 250 targets per acquisition) can provide an accuracy in antenna pattern estimation of about 0.04 dB, if the target accuracy is 0.1 dB at $1\sigma$ .

Local Detection of Moving Targets in SAR Image Based on NRS Hypotheses

Ground moving target indication (GMTI) is one of the important applications of synthetic aperture radar (SAR). This paper introduces a GMTI method for local detection of the ground moving targets in SAR image based on normalized relative speed (NRS) hypotheses. The input of the GMTI method is a complex SAR image where areas of interest for GMTI are locally selected. The output of the method includes the detected targets, the NRSs with respect to the SAR platform, the locations where the detected targets are focused, and the SAR images of the detected targets. The mathematical background of the GMTI method is presented in detail. The method is validated with the data delivered by the Coherent All-Radio Band Sensor, an airborne ultrawideband-ultrawidebeam low-frequency SAR system. The shortcomings of the introduced method are investigated and followed with the solutions.

Measurement of Ionospheric Scintillation Parameters From SAR Images Using Corner Reflectors

Space-based low-frequency (L-band and below) synthetic aperture radar (SAR) is affected by the ionosphere. In particular, the phase scintillation causes the sidelobes to rise in a manner that can be predicted by an analytical theory of the point spread function (PSF). In this paper, the results of an experiment, in which a 5 m corner reflector on Ascension Island, was repeatedly imaged by PALSAR-2 in the spotlight mode are described. Many examples of the effect of scintillation on the SAR PSF were obtained, and all fit the theoretical model. This theoretical model of the PSF has then been used to determine two ionospheric turbulence parameters p and $\text {C}_{\text {k}}\text {L}$ from the SAR PSF. The values obtained have been compared with those obtained from simultaneous GPS measurements. Although the comparison shows that the two measures are strongly correlated, the differing spatial and temporal scales of SAR and GPS make exact comparison difficult.