Longitudinal Tensile Strength Research Articles

Controlled Interlayer Binding and Healing Improve the Transverse Properties of Upcycled Disposable Waste Wood.

Recovery and reuse of bulk waste wood are particularly challenging because of usage defects and contaminations. Here, we present a robust and efficient strategy for regenerating used wood veneers into high-performance structural materials through micro/nano interface manipulation. Our approach involves using cellulose-based interlayers to bind together two waste wood plates without an external adhesive by partially dissolving and regenerating the interlayer using a solution of ionic liquids and dimethyl sulfoxide. The mechanical properties of the regenerated wood exceed that of natural wood, displaying over a 16 and 20 times increase in transverse tensile strength and modulus, respectively, and 4-6 times improvement in longitudinal tensile strength and modulus. Nanoscale mechanical analyses show that the improvement is possible as a result of several factors, including the robust network structure of the interlayer, the good adhesion at the wood-interlayer interface, the compacted wood structure, and the low stiffness and deformation gradients between the interlayer and the wood structure. The interlayers can be created from waste papers and wood particles by taking advantage of the nanofibrillar structure of cellulose.

Methacrylate-based shape manipulable wood with catalyst-free dynamic hemiacetal ester networks

The insufficient structural design and unfriendly preparation have greatly limited the development of thermal-induced shape memory materials. A methyl methacrylate (MMA)-based shape manipulable wood composite (SMW) is fabricated by integrating the catalyst-free hemiacetal ester networks with hierarchical anisotropic wood skeleton based on free radical in-situ polymerization and cross-linking reaction. In the as-obtained SMW, hierarchical wood framework (WF) and high-strength MMA act as mechanical skeleton and polymer network backbone, respectively, while methacrylic acid (MAA) promotes dynamic cross-linkage. The SMW possesses satisfactory comprehensive performances including desirable preparation efficiency, ideal optical property, anisotropic light-guiding effect, low thermal conductivity (≈0.22 W·m−1·K−1), satisfactory UV shielding effect and benign mechanical performances (longitudinal tensile strength of 34.54 MPa and flexural strength of 53.64 MPa). The catalyst-free dynamic exchange reaction combined with hierarchical wood skeleton endows the obtained SMW with shape memorability and manipulability, and the shape can be manipulated on demand without environmental-burden catalyst, which facilitates the industrial exploration, add-value development, and intelligent application of wood-based materials.

A comparison between tensile and hole expansion properties in 800 MPa tensile strength grade hot-rolled steels

Sheared edge formability can play a critical role in cold forming of high-strength hot-rolled steels due to susceptibility to edge cracking. Standardized ISO 16630 hole expansion test is currently the most widely used method to estimate sheared edge formability of steel sheets, however, there has been increasing interest in the industry to reduce the amount of required testing. The aim of this paper was to compare hole expansion performance of hot-rolled strip steels to various uniaxial tensile test results. The five investigated steels were selected to have 3 mm thickness and similar (838±10 MPa) longitudinal tensile strength level while consisting of different microstructures. Tensile properties were measured in 0°, 45°, and 90° angle relative to the rolling direction to investigate anisotropy. Plastic strain ratios were determined by digital image correlation measurement. Local ductility was evaluated with thickness strain measurements (εp_amin) on fracture surfaces of the tensile specimens. To investigate stretch-flangeability, ISO 16630 conforming hole expansion tests were performed. Test holes were produced by punching and by wire electrical discharge machining (W-EDM) to evaluate edge damage tolerance of the materials. The hole expansion ratios (HER) were not observed to correlate with majority of the investigated tensile test results, such as uniform elongation and yield strength. However, a good correlation between HER and planar anisotropy was observed. Planar anisotropy is seen to affect strain localization tendency around the hole. The HER values of neither punched nor W-EDM specimens correlated clearly with εp_amin measurement results. The results show that at a similar strength level, anisotropy is highly influencing the hole expansion performance of hot-rolled steels, and that the HER is not reliably predicted by a single local formability parameter.

The strength prediction model of unidirectional fiber reinforced composites based on the renormalization group method

When unidirectional fiber reinforced composites are subjected to longitudinal tensile loading and reach a critical failure state, they experience a sudden transition from local damage to catastrophic failure, commonly termed as an avalanche event. This paper integrates the self-organized criticality theory (SOC) concepts into the prediction of longitudinal tensile strength of composites and establishes a strength prediction model of composites based on the renormalization group method (RGM). The predictions of the RGM model are successfully validated against experimental results in the literatures, and it demonstrates relatively acceptable predictive accuracy compared to classical strength criteria. Compared to other state-of-the-art prediction models considering stochastic fiber strength distribution, the RGM model effectively provides strength statistics for fiber bundles of any size and describes the occurrence of composites avalanche failure induced by local stress concentration. This present model can be very conveniently implemented as a User Material Subroutine (UMAT) for finite simulations, facilitating practical prediction of the strength of composites structures.

Integrated accelerated testing methodology for CFRP durability

Integrated ATM, an integrated accelerated testing methodology for CFRP durability, is described herein. It is expressed as a single formula including several parameters representing the life of CFRP under an arbitrary environmental temperature and an arbitrary strain ratio R from R = 0 to 1. Integrated ATM is based on Christensen's viscoelastic crack kinetics and conventional ATM. First, Integrated ATM is introduced based on the matrix resin viscoelasticity. Second, important parameters which affect CFRP life are found for the longitudinal tensile strength of a unidirectional CFRP as an Integrated ATM application. Finally, the parameter influences on CFRP life are assessed.

Relationship between mechanical properties and height-diameter ratio of moso bamboo

Systematic tests of longitudinal compression, bending, longitudinal shear, and longitudinal tensile strength of bamboo were conducted to study the variation of mechanical properties and the height-diameter ratio of bamboo. The predictive relations of mechanical properties and height-diameter ratio were fitted by linear regression analysis. The results showed that the mechanical properties of longitudinal compression, bending, longitudinal shear, and longitudinal tensile strength of bamboo increased with the increase of the height-diameter ratio. In this paper, the method of deducing the relationship between mechanical properties and height-diameter ratio of bamboo through the linear fitting relationship between mechanical properties and height-diameter ratio was shown to have high applicability and accuracy for bamboo. This paper has a certain reference value for the evaluation of mechanical properties of bamboo and has a certain practical value for reducing the testing cost.

A Novel Method to Enhance the Mechanical Properties of Polyacrylonitrile Nanofiber Mats: An Experimental and Numerical Investigation.

This study addresses the challenge of enhancing the transverse mechanical properties of oriented polyacrylonitrile (PAN) nanofibers, which are known for their excellent longitudinal tensile strength, without significantly compromising their inherent porosity, which is essential for effective filtration. This study explores the effects of doping PAN nanofiber composites with varying concentrations of polyvinyl alcohol (PVA) (0.5%, 1%, and 2%), introduced into the PAN matrix via a dip-coating method. This approach ensured a random distribution of PVA within the nanofiber mat, aiming to leverage the synergistic interactions between PAN fibers and PVA to improve the composite's overall performance. This synergy is primarily manifested in the structural and functional augmentation of the PAN nanofiber mats through localized PVA agglomerations, thin films between fibers, and coatings on the fibers themselves. Comprehensive evaluation techniques were employed, including scanning electron microscopy (SEM) for morphological insights; transverse and longitudinal mechanical testing; a thermogravimetric analysis (TGA) for thermal stability; and differential scanning calorimetry (DSC) for thermal behavior analyses. Additionally, a finite element method (FEM) analysis was conducted on a numerical simulation of the composite. Using our novel method, the results demonstrated that a minimal concentration of the PVA solution effectively preserved the porosity of the PAN matrix while significantly enhancing its mechanical strength. Moreover, the numerical simulations showed strong agreement with the experimental results, validating the effectiveness of PVA doping in enhancing the mechanical properties of PAN nanofiber mats without sacrificing their functional porosity.

Hierarchical interface design of jute fibers/polypropylene composites for enhanced interfacial and mechanical properties

Natural fiber reinforced plastics (NFRPs) represent a promising category of emerging materials for sustainable industrial development owing to their renewability, degradability, and lightweight. However, the polarity mismatch between the fibers and polymer matrices weakens the mechanical properties of NFRPs. To address this issue, a novel hierarchical interface design was proposed here through the co-modification of silane coupling agents (SCAs) and zinc oxide nanorods (ZnO NRs), which exhibits not only high efficiency but also low energy consumption and environmental friendliness. Specifically, the hierarchical interface design was demonstrated on jute fibers (JFs)/polypropylene (PP) composites, where the JFs/ZnO interfaces were chemically bonded through complexation, chelation, or coordination using various SCAs; meanwhile, the ZnO/PP interfaces were physically bonded by interlocking effect. The experimental testing results indicated the exceptional mechanical properties of modified JFs and their composites. The JFs modified with 3-glycidyloxypropyltrimethoxysilane (KH560) and ZnO NRs exhibited an increase of 34.3% and 55.8% in single-fiber tensile strength and tensile modulus, respectively, compared to sololy ZnO coated JFs, and also showed an augment of 30.8% in the interfacial shear strength with PP resin. Thus, the transverse and longitudinal tensile strength of JFs/PP composites with combined modification of KH560 and ZnO NRs were 19.2% and 46.5% higher than untreated ones. The interfacial enhancement mechanism was ascribed to the synergistic effect of chemical bonding and physical interlocking, as revealed by molecular dynamics simulation and observation of fracture morphologies. The findings offer a cost-effective solution for developing JFs/PP composites with superior interfacial and mechanical properties, thereby promoting the practical applications and value of NFRPs.

Enhancing the geometry accuracy and mechanical properties of wire arc additive manufacturing of an Al-5%Mg alloy through longitudinal magnetic field influence

To address the issues of low deposition efficiency, poor geometric accuracy, and high porosity in wire arc additive manufacturing (WAAM) specimens, a longitudinal alternating current (AC) magnetic field-assisted WAAM method was employed. The results showed that the introduction of the longitudinal AC magnetic field significantly enhanced the geometric accuracy of the specimens. After magnetic field assistance, the porosity of the WAAM Al-5%Mg alloy specimens decreased from 0.372 % to 0.016 %. The grain size decreases from 71.95 μm to 56.3 μm, with a notable increase in the proportion of small grains (D < 30 μm) from 27.06 % to 44.57 %. The longitudinal tensile strength increased from 243 MPa to 260 MPa, while the transverse tensile strength increased from 232 MPa to 257.7 MPa. Moreover, the longitudinal and transverse tensile strengths tended to be isotropic. Therefore, the longitudinal AC magnetic field has a significant impact on the performance of AlMg alloy WAAM specimens. This study presents novel strategies and theoretical guidance for enhancing the efficiency and component performance of aluminum alloy WAAM technology.

Effect of shear stresses on fibre direction tensile failure using a new simple and reliable test method with thin plies

A new method of creating in-plane combined tension-shear stress states using only tensile loading is proposed. Thin-ply angle-ply carbon/epoxy laminates are sandwiched between unidirectional glass layers to eliminate any stress concentration around the samples ends and gripping zone. Use of the thin plies successfully suppresses early occurrence of other modes of failure i.e. matrix cracking and free-edge delamination, so the first mode of failure is fibre failure in the angle-ply carbon sub-laminate. Compared with other methods of creating combined tension-shear stresses, the proposed technique has a simpler geometry, is significantly easier and cheaper to manufacture and test. Therefore, it provides more repeatable low-scatter experimental results.The obtained experimental results showed that the presence of in-plane shear stresses did not have a significant impact on the tensile fibre-direction failure strain of the tested carbon/epoxy laminate, suggesting that even at high shear stresses, the longitudinal tensile strength of the carbon/epoxy laminate is not significantly reduced.

Polyethylene terephthalate bottles with excellent oxygen, water vapor barrier and mechanical performances prepared by injection and blow molding

AbstractIn this work, the oxygen barrier property of polyethylene terephthalate (PET) films was enhanced by optimizing the “active” and “passive” synergistic barrier approaches, that is, integration of high barrier material polyethylene naphthalate (PEN) and oxygen scavengers along with catalyst with PET before biaxially stretching the PET blended films. When the PEN content in the PET blended films reached 50 wt%, the oxygen permeability coefficient was significantly reduced to 0.9687 cc·mil·m−2·day−1·0.1 MPa−1, showing an enhancement of 117.4 times compared to the pure PET film. Furthermore, the water vapor permeability coefficient was reduced to 8.0208 g·mil·m−2·day−1, representing a 45.5% reduction in comparison to the pristine PET film. It also maintained a higher transverse and longitudinal tensile strength (110.5 and 127.2 MPa) than PET film only with oxygen scavengers and catalyst (53.5 and 78.0 MPa). This work presents a viable and practical approach to endow PET materials with simultaneously enhanced oxygen, water barrier performance, and mechanical property.Highlights The OPC of PET film was as low as 0.9687 cc·mil·m−2·day−1·0.1 MPa−1. The “active” and “passive” barrier techniques together reduced the OPC of PET film.

Effect of Dispersing In Situ Al-Cu Intermetallic Compounds on Joint Strength in Friction Stir Welding of AA3003-H18 Sheets

In this study, friction stir welding (FSW) was employed to join AA3003-H18 sheets by incorporating in situ Al-Cu intermetallic compounds within the stir zone. The FSW process was carried out under three distinct conditions: (I) without applying powder, (II) by introducing Cu powder, and (III) by incorporating Cu-Al mixed powder (50 vol.% Cu, 50 vol.% Al). The powder was embedded into the gap between two sheets. Subsequently, two-pass FSW, involving both forward and backward movements, was conducted with a rotational speed of 1200 rpm and traverse speed of 100 mm/min across all three experimental conditions. In the second and third conditions, the formation of in situ intermetallic compounds occurred through a solid-state reaction between Cu particles and Al within the stir zone. Examination of the stir zone through optical and electron microscopic studies revealed that the utilization of Cu-Al mixed powder resulted in finer and more uniformly distributed Cu clusters and Al-Cu intermetallics than samples welded with Cu powder alone. Notably, the stir zone of samples incorporating Cu-Al mixed powder exhibited finely dispersed, completely gray Al-Cu intermetallic particles, whereas those with only Cu powder displayed predominantly coarse core-shell particles in the microstructure. The introduction of Cu-Al mixed powder during FSW resulted in a stir zone with an average hardness of 74 HB, showing a 14% increase compared to the cases where Cu powder alone was added (65 HB). Tensile tests, conducted in both transverse and longitudinal directions on the FSWed samples, did not exhibit a consistent trend across the three mentioned conditions. Transverse tensile strength consistently ranged between 107 and 110 MPa, with joint efficiency varying from 52% to 54%. However, the longitudinal tensile strength of the joint with added Cu-Al mixed powder (158 MPa) surpassed those welded with Cu powder alone (134 MPa).

Calculation of the stress-strain state of layers of cross-ply laminate based on an experimental stress-strain curves under uniaxial tension

A method for calculating the stress-strain state of layers of cross-ply laminate based on an experimental deformation diagram under uniaxial tension is proposed. The essence of the method consists in solving a system of two equations describing the experimental curves σx = f(εx) and σx = f(εy), which allows determination of two unknown parameters related to the secant elastic characteristics of the material layers. The law of change in the remaining unknown parameters is set by assumptions regarding deformation of the polymer matrix composite and its layers during loading. To carry out the calculation, it is necessary to set the initial values of the elastic properties of the unidirectional material of the layers, which should be well consistent with the initial values of the elastic properties of the structure under study determined from the experiment. According to the developed algorithm, calculated dependences between average stresses, deformations and secant elastic properties of the layers of the structure are obtained (0°/90°/90°/0°) made of fiberglass E-Glass/MY750 using experimental data from the literature. Calculations carried out for three sets of initial values of the elastic properties of the material under study showed qualitatively identical results. The transverse tensile stress in the 90° layer reaches a maximum in the first half of the stress-strain diagram, and then decreases to zero. A similar stress in the 0° layer reaches a maximum at the failure point of the structure under study. It is revealed that the maximum calculated values of transverse stresses acting in layers 0° and 90° noticeably exceed the transverse tensile strength of the material specified in the literature. The longitudinal tensile stress in the 0° layer reaches a maximum at the failure point and corresponds to 95% of the value of the longitudinal tensile strength of the material. The longitudinal compressive stress in the 90° layer is at a low level throughout the deformation process of the structure under study. The results of this study can be recommended for developing models of the behavior of layers with cracks in the matrix when loading a polymer matrix composite.

High-Strength, High-Swelling-Resistant, High-Sensitivity Hydrogel Sensor Prepared with Wood That Retains Lignin.

Wood-derived hydrogels possess satisfactory longitudinal strength but lack excellent swelling resistance and dry shrinkage resistance when achieving high anisotropy. In this study, we displayed the preparation of highly dimensional stable wood/polyacrylamide hydrogels (wood/PAM-Al3+). The alkali-treated wood retains lignin as the skeleton of the hydrogel. Second, Al ions were added to the metal coordination with lignin. Finally, by employing free radical polymerization, we construct a conductive electronic network using polyaniline within the wood/PAM-Al3+ matrix to create the flexible sensor. This approach leverages lignin's integrated structure within the middle lamella to provide enhanced swelling resistance and stronger binding strength in the transverse direction. Furthermore, coordination between lignin and Al ions improves the mechanical strength of the wood hydrogel. Polyaniline provides stable linear pressure and temperature responses. The wood/PAM-Al3+ exhibits a transverse swelling ratio of 3.90% while achieving a longitudinal tensile strength of 20.5 MPa. This high-strength and high-stability sensor is capable of monitoring macroscale human behavior. Therefore, this study presents a simple yet innovative strategy for constructing tough hydrogels while also establishing an alternative pathway for exploring lignin networks in new functional materials development.

Photoluminescent Transparent Wood with Excellent UV-Shielding Function.

At present, light transmission, energy saving, environmental protection, and UV-shielding materials are very important for optimizing indoor living environment. Here, a fluorescent transparent wood (FTW) with UV-shielding function was prepared by encapsulating a carbon quantum dot and epoxy resin into a delignification wood template. FTW exhibits excellent optical transmittance (about 91%), water absorption stability (weight gain rate less than 9%), longitudinal tensile strength (139 MPa), and UV-shielding properties. Due to the photoluminescence characteristics of the carbon quantum dot and the natural cellulose skeleton of wood, FTW can show uniform luminescence under ultraviolet lamps. At the same time, it has remarkable UV-shielding performance. This kind of photoluminescent transparent wood with a UV-shielding function also has the potential to be applied to fields such as electromagnetic shielding and harmful gas detection.

Investigation of T-stress and tensile strength effect on crack tip conditions and crack initiation angle in off-axis laminate composite

In this work, five different yield criteria have been used, maximum tangential stress (MTS), maximum energy release rate (MERR), Hill-48, Hill-90, and Barlat-93, in order to determine crack initiation angle. A study is performed to investigate the effect of T-stress on crack initiation angle. For this purpose, the elastic–plastic core region is plotted, and the R-criterion suggests that the crack initiates along local minimum (negative value) or global minimum (positive value) direction depending on the stress state at the crack tip. It is found that a negative value of T-stress makes the crack move toward the loading direction (T-axis), or in other words, the crack initiation angle decreases. It also turns out that MERR and Barlat criteria show a better result for crack initiation angle. The yield surface and elastic–plastic core region have also been plotted for different tensile strengths. For the case when transverse tensile strength equals to z-direction tensile strength, Hill-48, Hill-90, and Barlat show the same yield surface, and approximately, the same crack initiation angle. Also, when transverse tensile strength is smaller than longitudinal tensile strength, crack tends to move toward x-direction (local coordinate placed on crack tip). Finally, a FE simulation is performed to numerically determine SIFs.

Reducing stress concentrations in static and fatigue tensile tests on unidirectional composite materials: A review

The longitudinal tensile strength is an important basic property of unidirectional (UD) composites or plies that often governs failure in multidirectional laminates. The standard tensile testing methods almost always result in sample failure near the grip. Finite element analyses revealed the presence of multiaxial stress concentrations, including longitudinal, transverse, and shear stresses in the tabbed section of the standards’ recommended design. There are still unknowns and uncertainties about the causes of these stress concentrations and ways to eliminate them. A major challenge is obtaining acceptable failure within the gauge section and yielding the highest tensile strength of UD composites. This paper reviews the different methods for performing quasi-static and fatigue tensile tests on UD composites. The primary sources of stress concentrations and the parameters that affect them are reviewed using the available experimental and modeling investigations. We survey the effects of the different specimen and end tab designs as well as test setups on quasi-static and fatigue loading. Specific proposals are made for each of the discussed parameters for more reliable results.

Microstructure Formation and Its Effect on Mechanical Properties for Duplex Stainless Steel 2205 Plasma Arc Welded Joint

The control of phase balance has always been a tough challenge for the welding of duplex stainless steel, which heavily restricts its optimal serving performance in engineering. The microstructure development and mechanical characteristics of SAF2205 plasma arc welded joints were thoroughly examined in this paper. It was proven that the phase balance can be well controlled by plasma arc welding, and the austenite content of the welded joints was about 60%. Despite successful phase control, there was still grain coarsening and distortion; i.e., at the center of the welded zone, the gain size was about eight times that of the base metal, and the austenite was mainly in the form of grain boundary austenite and intragranular austenite, while more Widmanstatten austenites were found in the heat-affected zone. In addition, a transition region between the heat affected zone and the center exhibited columnar ferritic grains. Furthermore, the plasticity and toughness of the welded joints were significantly decreased, especially the elongation in the longitudinal direction, which is about 10% lower than that of the base metal, and transversal tensile strength remained comparable to the base metal, with only a slight reduction in longitudinal tensile strength. Lastly, the formation mechanism of microstructure and its correlation with mechanical properties were revealed. This investigation offers valuable insights into the structural integrity of duplex stainless steel welded joints in engineering applications.

Core-shell structured tow-pregs enabled additive manufacturing of continuously reinforced thermoset composites

One of the major challenges in thermally curable polymer composite additive manufacturing is the slow curing time of thermally curable resins, coupled with a significant drop in thermoset viscosity upon heating, making the formation of complex shapes difficult. To tackle these issues, we have introduced a novel rapid composite preformation strategy called Tow-Preg Cladding (TPC). This technique involves the use of a thin and rapidly curable dual-cure resin, which combines a thermally curable resin (such as epoxy) with a fast photo-curable resin. The dual-cure resin is applied as a coating over a thermally curable resin tow-preg, enabling the formation of a rigid cladding that supports and shapes the tow-pregs into the desired geometries and patterns. The key advantage of this approach lies in the sequential formation of an interpenetrating polymer network (IPN) at the interlayer between laminates, resulting from the curing of the photocurable resin and the thermally curable resin sequentially. This IPN formation enhances interlaminar bonding in the composite, contributing to its overall strength and performance. The composites produced using this technique exhibited impressive mechanical properties, including longitudinal tensile strength of 1058.2 MPa, longitudinal tensile modulus of 74.2 GPa, flexural strength of 1080.4 MPa, and flexural modulus of 41.7 GPa. Overall, our Tow-Preg Cladding approach shows great promise in overcoming the challenges associated with thermally curable polymer composite additive manufacturing. It offers a viable solution to creating strong, shape-specific thermoset composites efficiently with enhanced mechanical properties.

Reliability analysis and optimization design of hydrogen storage composite pressure vessel with hybrid random-fuzzy uncertainties

In this study, a progressive failure model for hydrogen storage composite pressure vessel (CPV) burst is established. The burst pressure and progressive damage behavior of the CPV are analyzed. Besides, kriging and response surface (RS) surrogate models for CPV burst are established. The verification and the comparative analysis of the surrogate models are carried out. Then, the reliability of the CPV is analyzed with hybrid random-fuzzy uncertainties, and the influence of longitudinal tensile strength, hoop layer thickness, and helical layer thickness on the hybrid reliability is explored. Finally, a unified reliability index is established with hybrid random-fuzzy uncertainties, and the modified particle swarm optimization (PSO) algorithm is applied to carry out reliability-based optimization design. The minimum weight of the composite shell is set as the objective, and the reliability of the CPV with hybrid random-fuzzy uncertainties is set as the constraint. The results show that the hoop layer of the CPV is the main load-bearing structure. The kriging and RS surrogate models are effectiveness to surrogate the burst pressure of the CPV, and the RS model is simpler and more computationally efficient than kriging model, which is more suitable for reliability analysis and optimization design. Under the condition of hybrid random-fuzzy uncertainties, the reliability of the hydrogen storage CPV exhibits fuzzy uncertainty, and there is a possibility of reliability equal to 0 under the low λ-cut level, making it difficult to meet reliability requirements. Increasing the longitudinal tensile strength, the hoop layer thickness and the helical layer thickness can improve the reliability of the hydrogen storage CPV. Furthermore, the optimization method proposed in this study improves its reliability from 0.7043 to 1. This study establishes reliability analysis and optimization design methods for hydrogen storage CPV with hybrid random-fuzzy uncertainties, which contributes to further improvement on the safety of CPV.