Lignocellulosic Research Articles

Biomass recovery of coastal young mangrove plantations in Central Thailand.

Around one-third of the world's most carbon-rich ecosystems, mangrove forests, have already been destroyed in Thailand owing to coastal development and aquaculture. Improving these degraded areas through mangrove plantations can restore various coastal ecosystem services, including CO2 absorption and protection against wave action. This study examines the biomass of three coastal mangrove plantations (Avicennia alba) of different ages in Samut Prakarn province, Central Thailand. Our aim was to understand the forest biomass recovery during the early stages of development, particularly fine root biomass expansion. In the chronosequence of the mangrove plantations, woody biomass increased by 40% over four years from 79.7 ± 11.2Mg C ha-1 to 111.7 ± 12.3Mg C ha-1. Fine root biomass up to a depth of 100cm was 4.47 ± 0.33Mg C ha-1, 4.24 ± 0.63Mg C ha-1, and 6.92 ± 0.32Mg C ha-1 at 10, 12, and 14year-old sites, respectively. Remarkably, the fine root biomass of 14-year-old site was significantly higher than those of the younger sites due to increase of the biomass at 15-30cm and 30-50cm depths. Our findings reveal that the biomass recovery in developing mangrove plantations exhibit rapid expansion of fine roots in deeper soil layers.

Natural lignocellulosic biomass structure inspired CNF/Lignin/PBAT composite film with thermoplastic, antibacterial and UV-blocking abilities.

The development of a thermoplastic, biodegradable composite material to replace conventional polymers derived from petroleum was the main area of concentration. Herein, a method for preparing antibacterial, UV-blocking and degradable CNF/Lignin/PBAT composite films (CLP) using cellulose nanofibrils (CNFs), lignin, and Poly (butylene adipate-terephthalate) (PBAT) as raw materials by solution casting method was described. With the adding of PBAT, the thermal stability, thermoplastic, mechanical properties were enhanced by improving the compatibility between components. The maximum tensile strength of CLP could reach 189.72 MPa, which increased 25.5 % compared to CNF/Lignin film. The average initial decomposition temperature could reach 321 °C, which much higher than that of CNF and lignin. At the same time, it holds good heat-sealing performance made it suitable for practical use. Meanwhile, the composite films had excellent UV resistance and could block over 95 % of UV light. The antibacterial results indicated that the films had a good inhibitory effect on E. coli and S. aureus, with a maximum inhibitory ring diameter of 5.56 and 6.36 mm. In addition, the composite film also had excellent barrier capability to liquid and gas. The prepared film had potential to produce flexible packing, industrial compositing and biomedical fields.

Pretreatment of wastepaper with an aqueous solution of amino acid-derived ionic liquid for biochar production as adsorbent.

The carbonization of lignocellulosic biomass with ionic liquids (ILs) are considered as an advantageous approach for the preparation of carbonaceous materials. The commonly used imidazolium and pyridinium based ILs have drawbacks such as toxicity, resistance to biodegradation, high cost and viscosity. These issues can be mitigated by diluting ILs with water, although excessive water content above 1wt% can reduce the solubility of biomass. This research aims to investigate the potential of pretreating wastepaper with a "fully green" ILs, amino acid-based IL with high water content, followed by pyrolysis without IL, in enhancing the properties of biochar. For this purpose, the paper was treated with an aqueous solution of IL cysteine nitrate ([Cys][NO3]), and the IL was not involved in the pyrolysis process to prevent the formation of secondary gaseous pollutants. The findings revealed that the hemicellulose and mineral filler in the paper were eliminated during pretreatment, leading to higher carbon content but lower oxygen content. As a result, the biochar exhibited micropores of 0.42 cm3g-1 and a specific surface area of 1011.21m2g-1. The biochar demonstrated high adsorption capacities for Cd2+, enrofloxacin, bisphenol A, ciprofloxacin, and tetracycline, with values of 45.20mgg-1, 49.82mgg-1, 49.90mgg-1, 49.88mgg-1, and 49.65mgg-1, respectively. The proposed mechanism for the adsorption of enrofloxacin by the biochar primarily involves physical adsorption such as pore filling and electrostatic interactions, along with chemical adsorption facilitated by graphitic nitrogen.

LIGNOCELLULOSIC BIOMASS FOR BIOCHAR PRODUCTION: A GREEN INITIATIVE ON BIOWASTE CONVERSION FOR PHARMACEUTICAL AND OTHER EMERGING POLLUTANT REMOVAL.

Lignocellulosic waste generation and their improper disposal has accelerated the problems associated with increased greenhouse gas emissions and associated environmental pollution. Constructive ways to manage and mitigate the pollution associated with lignocellulosic waste has propelled the research on biochar production using lignocellulose-based substrates. The sustainability of various biochar production technologies in employing lignocellulosic biomass as feedstock for biochar production not only aids in the lignocellulosic biomass valorization but also helps in carbon neutralization and carbon utilization. Functionalization of biochar through various physicochemical methods helps in improving their functional properties majorly by reducing the size of the biochar particles to nanoscale and modifying their surface properties. The usage of engineered biochar as nano adsorbents for environmental applications like dye absorption, removal of organic pollutants and endocrine disrupting compounds from wastewater has been the thrust areas of research in the past few decades. This review presents a comprehensive outlook on the up-to-date research findings related to the production and engineering of biochar from lignocellulosic biomass and their applications in environmental remediation especially with respect to wastewater treatment. Further a detailed discussion on various biochar activation methods and the future scope of biochar research is presented in this review work.

A review of nanotechnology in enzyme cascade to address challenges in pre-treating biomass.

Nanotechnology has become a revolutionary technique for improving the preliminary treatment of lignocellulosic biomass in the production of biofuels. Traditional methods of pre-treatment have encountered difficulties in effectively degrading the intricate lignocellulosic composition, thereby impeding the conversion of biomass into fermentable sugars. Nanotechnology has enabled the development of enzyme cascade processes that present a potential solution for addressing the limitations. The focus of this review article is to delve into the utilization of nanotechnology in the pretreatment of lignocellulosic biomass through enzyme cascade processes. The review commences with an analysis of the composition and structure of lignocellulosic biomass, followed by a discussion on the drawbacks associated with conventional pre-treatment techniques. The subsequent analysis explores the importance of efficient pre-treatment methods in the context of biofuel production. We thoroughly investigate the utilization of nanotechnology in the pre-treatment of enzyme cascades across three distinct sections. Nanomaterials for enzyme immobilization, enhanced enzyme stability and activity through nanotechnology, and nanocarriers for controlled enzyme delivery. Moreover, the techniques used to analyse nanomaterials and the interactions between enzymes and nanomaterials are introduced. This review emphasizes the significance of comprehending the mechanisms underlying the synergy between nanotechnology and enzymes establishing sustainable and environmentally friendly nanotechnology applications.

Physicochemical characterization of rice straw before and after alkali-assist photocatalytic pretreatment: a comparative analysis.

The potential of alkali-assist photocatalytic (AAP) pretreatment to overcome the recalcitrant nature of lignocellulose biomass, i.e. rice straw (RS), was investigated in the present study. Box-Behenken Design (BBD) using standard response surface methodology (RSM) approach was considered to obtain optimal conditions for maximum delignification. The model was designed with three variables: alkali concentration (NaOH, 0-3% w/v), photocatalyst (TiO2 NPs (titania nanoparticles), 0-1g/L) and pretreatment time (30-240min). The availability of cellulose was increased by 96.73%, while the concentration of lignin and hemicellulose decreased by 73.89%, and 71.79%, respectively, at a combination of 1.5% NaOH, 0.5g/L TiO2 NPsand 135 min pretreatment time. The structural and morphological alterations in the RS were assessed via Fourier Transform Infrared spectroscopy (FTIR), X-ray diffraction (XRD) and scanning electron microscopy (SEM) both before and after AAPpretreatment. The FTIR measurement indicated that the original RS included a significant quantity of lignin, which was eliminated after the pretreatment procedure. The XRD pattern demonstrates that cellulose crystallinity is significantly affected by the pretreatment. The SEM analysis revealed structural distortion and surface porosity from the pretreatment procedure.

The significance of structural components of lignocellulosic biomass on volatile organic compounds presence on biochar - a review

The significance of structural components of lignocellulosic biomass on volatile organic compounds presence on biochar - a review

Prediction of Individual Gas Yields of Supercritical Water Gasification of Lignocellulosic Biomass by Machine Learning Models

Prediction of Individual Gas Yields of Supercritical Water Gasification of Lignocellulosic Biomass by Machine Learning Models

A Novel Compatibilizer Obtained from Olive Pomace Oil Maleate (OPOMA) and Evaluation in PLA Composite Production

Alternative of using organic and biomass residues as additives or reinforcements in the production of composite materials has attracted great attention since the 2000s. However, when lignocellulosic biomass is used as natural fiber in composite production, it may have some disadvantages such as low interfacial bonding with the matrix phase. The most common methods used to strengthen the bonding between the matrix phase and the additive material is to use maleic anhydride (MA) as a compatibilizer and some chemicals such as dicumyl peroxide (DCP) as reaction initiators to increase the compatibilizing effect of MA. Therefore, in this study, olive pomace oil maleate (OPOMA) was prepared to be used in the production of PLA composites. Olive pomace obtained with ionic liquid pretreatment (OP-IL) in the previous studies of the authors and OPOMA were used in composite production with a biodegradable polymer of PLA. The composite was obtained by mixing 95PLA+5OP-IL by weight in twin-screw extruder at 190ºC for 10 minutes. Under the same conditions, the effect of OPOMA was evaluated by adding 0.5%, 1% and 2% ratio to PLA + OP-IL. In FTIR spectrum of OPOMA, a new symmetrical and asymmetric C=O bands were formed differently from olive oil. While the addition of low doses of OPOMA to PLA+OP-IL composites increased the tensile elongation value, tensile strength did not change. The elasticity modulus showed less change compared to other mechanical properties. To conclude, it can be emphasized that oil maleates of lignocellulosic biomasses can be promising compatibilizer for biodegradable composite matrices

Valorization of rice straw and vascular aquatic weeds for sustainable prebiotic hemicellulosic autohydrolysate production: Extraction, characterization and fermentability.

This study describes the extraction and characterization of the hemicellulosic autohydrolysates (HAHs) derived from rice straw (RS) and vascular aquatic weeds like Typha angustifolia (TA) and Ceretophyllum demersum (CD). It further explores their capacity to sustain the proliferation of selected lactic acid bacteria (i.e., prebiotic activity) isolated from milk samples. To fractionate HAH from RS, TA and CD hot water extraction (HWE) method was used and RS, TA, and CD biomasses yielded 6.8, 4.99 and 2.98% of HAH corresponding to the hemicellulose extraction efficiencies of 26.15 ± 0.8%, 23.76 ± 0.6%, and 18.62 ± 0.4% respectively. The chemical characterization of HAH concentrates through HPLC showed that they comprised galactose, arabinose, xylose and glucose. The total phenol content of the RS, TA and CD-derived HAH concentrates were 37.53, 56.78 and 48.08mg GAE/g. The five lactic acid bacteria (LAB) isolates Q1B, Q2A, Q3B, G1C and G2B selected for prebiotic activity assays generated mixed responses with the highest growth in RS-HAH for Q2A and the least in TA-HAH for Q3B. Further, the isolates Q2A, Q3B, G1C, and G2B, which showed the highest growth performance, were identified through MALDI-TOF and 16S rRNA sequencing as Lactobacillus brevis. All the tested LAB isolates showed diauxic growth in crude HAH preparations to maximize the utilization of carbon resources for their proliferation. This suggests that the selected LAB isolates are efficient degraders of hemicellulosic sugars. This paves the way for the valorization of lignocellulosic biomass to produce prebiotic hemicellulosic autohydrolysate and consequently enhances environmental sustainability by improving resource efficiency.

Wood Distillate Promotes the Tolerance of Lettuce in Extreme Salt Stress Conditions

Soil salinization is an adverse phenomenon in agriculture that severely affects crop growth and yield. The use of natural products, such as wood distillate (WD, derived from the pyrolysis of woody biomass), could be a sustainable approach to enhance the tolerance of plants cultivated in the saline soils. Hence, this study aimed to evaluate the potential of WD, a foliar sprayed at 0.2% (v/v), in lettuce plants subjected to grow under both moderate and high soil sodium chloride (NaCl) concentrations (ranging from 0 to 300 mM). The changes in the physiological and biochemical responses of these plants to the varying salt stress conditions allowed the identification of a maximum tolerance threshold (100 mM NaCl), specific to lettuce. Beyond this threshold, levels related to plant defense antioxidant power (antiradical activity) were lowered, while those indicative of oxidative stress (malondialdehyde content and electrolyte leakage) were raised, causing significant losses in leaf fresh biomass. On the other hand, WD significantly improved plant growth, enabling plants to survive high salt conditions >200 mM NaCl. Collectively, these observations highlight that treatments with WD could be of paramount importance in coping with current environmental challenges to have better yields under soil conditions of high salt concentrations.

Antimicrobial and antioxidant activities of lignin by-product from sugarcane leaf conversion to levulinic acid and hydrochar

To enhance the sustainability of lignocellulosic biomass utilization process, a significant attention is given to a high-value lignin byproduct of this process. Herein, antimicrobial, antioxidant, and physicochemical properties of lignin in black liquor extracted from sugarcane leaf (SCL) for levulinic acid (LA) and hydrochar production were investigated. The lignin was extracted from SCL through an alkaline pretreatment process using 5–25 wt% of either NaOH or KOH at 120–160 °C. Disk diffusion susceptibility tests, minimum inhibitory concentration (MIC), and minimum bactericidal concentration (MBC) revealed that the SCL lignin is effective against Gram-positive bacteria (S. aureus) rather than Gram-negative bacteria (E. coli and S. typhimurium). Different alkaline reagents marginally affected the antimicrobial and antioxidant activities of the lignin. Py-GC/MS analysis results determined that the SCL lignin contained mainly p-hydroxyphenyl (H) and guaiacyl (G) with a small amount of syringyl (S) lignin. Furthermore, the structural alterations and linkages of SCL lignin during alkaline pretreatment were examined using 2D-HSQC NMR, providing valuable insights into the transformation processes. The conversion of delignified SCL to LA through a catalytic hydrothermal process using various acid catalysts indicated that the alkaline pretreatment could enhance LA yield with a maximum yield of 33.4 wt%. Additionally, fuel property characterization of the hydrochar co-product from LA production determined that the hydrochar can be used as a coal substitute.

Pretreatment of lignocellulosic biomass for bioethanol production

This review surveys recent progress in pretreatment methods for enhancing bioethanol production from lignocellulosic biomass. Various pretreatment techniques, including physical, chemical, and biological approaches, are evaluated for their efficacy in breaking down biomass structure and improving enzymatic digestibility. Key parameters influencing pretreatment effectiveness and integration with downstream processes are discussed. The review highlights promising strategies and identifies areas for further research to optimize bioethanol production from lignocellulosic feedstocks.

Removal of Methylene blue dye from contaminated wastewater using lignocellulosic biomasses: A comparative study

In this study, lupine seed (Lu-SP) and pumpkin seed shells (PSSP) biomasses were used to create alternative and effective adsorbents. Methylene blue (MB) dye was removed from wastewater using the as-prepared adsorbents at variables solution pH 2.0 –11.0, contact period (0–180 min), and adsorbent mass (0.2–2.0 g/L). The solution pH had a synergistic effect on the improved removal of MB and the optimal adsorption removal for both adsorbents occurred at pH 8.0 and 120 min. The adsorption isotherm modelling results showed a good fit with the Langmuir model, with a maximum monolayer adsorption capacity of 48.98 and 77.48 mg/g for PSSP and Lu-SP, respectively. Similarly, the pseudo-first-order (PFO) model is regarded as the best-fit kinetic model for both adsorbents and suggests the predominance of physisorption via interfacial diffusion. Mechanistic investigation of the present system suggests that both intraparticle diffusion and surface sorption mechanisms control the adsorption rate. Notably, the Lu-SP with a lower surface area (54.013 m2/g) outperformed the PSSP (235.992 m2/g) in terms of adsorption capacity under varying pH. Therefore, in addition to electrostatic interaction, adsorption into the micropores via volume filling is considered one of the adsorption mechanisms. This study, therefore, revealed that the PSSP and Lu-SP may be very helpful for removing cationic MB dye from contaminated wastewater.

PRODUCTION OF MYCELIUM-BASED COMPOSITE MATERIALS AND EVALUATION OF THERMAL INSULATION PERFORMANCE

ABSTRACT Increasing awareness of the adverse effects of materials used in the construction industry on the environment and health increases the tendency towards bio-based products based on principles such as circular economy and sustainability. Meanwhile, there is a tendency to solve the post-use waste problem and reduce carbon emissions by extending the service life of building materials or making recyclable materials widespread. Mycelium-based composites (MBC) constitute an innovative natural building material interface with the potential to be used as building insulation material. In producing MBC, a substrate is used because of the significant growth provided by lignocellulosic biomass. In this study, MBCs were produced by growing Pleurotus ostreatus on 16 substrates during a 28-day incubation period. Consequently, two composites with the best performance were selected from the preliminary research on the produced samples. It was aimed to determine the thermal, mechanical, physical properties, microstructure characterization and longterm performance of the selected composites. For this reason, thermal conductivity coefficient measurement, water absorption values, water vapor permeability, ultrasound velocity determination, mechanical strength tests and durability tests were carried out. The findings showed that composites containing beech sawdust and pulp paper had better properties than other substrates. Advanced research results showed that MBCs are promising as thermal insulation materials.

Role of Particle Geometry on the Structural Integrity of Sand and Rock Ilmenite Used as Oxygen Carrier in Combustion of Woody Biomass

Role of Particle Geometry on the Structural Integrity of Sand and Rock Ilmenite Used as Oxygen Carrier in Combustion of Woody Biomass

Synergism of jet milling and deep eutectic solvent pretreatment on grapevine lignin fractionation and enhancing enzymatic hydrolysis

Herein, we investigated the synergistic effects of jet milling (JM) and deep eutectic solvent (DES) pretreatment on the fractionation of grapevine lignin and the consequent enhancement of enzymatic hydrolysis. Grapevine, a substantial byproduct of the wine industry, was subjected to JM pretreatment to produce finely powdered particles (median diameter D50 = 98.90), which were then further treated with acidic ChCl-LA and alkaline K2CO3-EG DESs. The results revealed that the combined JM + ChCl-LA pretreatment significantly increased the cellulose preservation under optimal conditions (110 °C, 4 h, and 20 % water content), achieving removal rates of 74.18 % xylan and 66.05 % lignin, respectively. The pretreatment temperature and inhibitor production were reduced, resulting in a remarkable threefold increase in glucose yield compared to untreated samples. Moreover, the structural analysis of the pretreated lignin indicated an enrichment of phenolic units, leading to enhanced antioxidant and antibacterial activities, particularly in the JM pretreated samples. These findings underscore the promising potential of the synergistic JM and DES pretreatment in facilitating the efficient utilization of grapevine lignocellulosic biomass for sustainable biorefinery technologies.

Biochar from co-pyrolysis of biological sludge and woody waste followed by chemical and thermal activation: end-of-waste procedure for sludge management and biochar sorption efficiency for anionic and cationic dyes.

Nine biochars were produced by co-pyrolysis of sawdust and biological sludge following the "design of experiment" approach. Two kinds of sludge (both deriving from the treatment of mixed industrial-municipal wastewater) and two types of woody waste were selected as categorical predicting variables, while contact time, pyrolysis temperature, and sludge percentage were used as quantitative variables. Biochars were analysed for their product characteristics and environmental compatibility based on the European Standards (EN 12915-1:2009) for materials intended for water treatment (i.e. ash content, water leachable polycyclic aromatic hydrocarbons (PAHs) and elements), as well as for specific surface area (SSA), using them as response variables of a multivariate partial least square multiple regression, whose results provided interesting insights on the relationships between pyrolysis conditions and biochar characteristics. Biochars produced with sludge and/or providing the highest SSA values (258-370 m2g-1) were selected to undergo a sustainable chemical treatment using a by-product of the gasification of woody biomass, complying in all cases with European Standards and achieving therefore the end-of-waste status for sewage sludge. The biochar deriving from the highest percentage of sludge (30% by weight) and with the highest SSA (390 m2g-1) was thermally activated achieving SSA of 460 m2g-1 and then tested for the sorption of direct yellow 50 and methylene blue in ultrapure water and real wastewater, compared to a commercial activated carbon (AC). The biochar showed Langmuir sorption maxima (Qm) 2-9 times lower than AC, thus highlighting promising sorption performances. Qm for methylene blue in wastewater (28mg‧g-1) was confirmed by column breakthrough experiments.

Unlocking the Full Potential of Green Catalysis: a Novel Thermosensitive Catalytic System for Ultrasonic-microwave Liquefaction of Woody Biomass

Unlocking the Full Potential of Green Catalysis: a Novel Thermosensitive Catalytic System for Ultrasonic-microwave Liquefaction of Woody Biomass

Role of Woody Biomass Ash Material in Immobilization of Cadmium, Lead and Zinc in Soil

Nowadays, we have observed the dynamic development of bio-heating plants that use wood biomass for heating or energy purposes. The result of this process is a reduction in carbon dioxide emissions as well as in the production of biomass ash (BA). Despite the waste nature of BA, it should be carefully analyzed and assessed for various applications, including environmental ones. Due to the features attributed to BA, including its alkaline reaction, the high capacity of its sorption complex, relatively low salinity, and significant content of macro- and microelements, a hypothesis was put forward in this work undertaken about the positive role of BA as an immobilizing factor for Cd-, Pb-, and Zn-contaminated soils. This research was based on a pot experiment in which four series were considered: (1) BA; (2) BA + Cd; (3) BA + Pb; and (4) BA + Zn. BA was used at doses of 30, 60, and 90 mg pot−1, and metals at doses of 2 mg Cd, 100 mg Pb, and 300 mg Zn kg−1 of soil. The test plant was corn grown for green mass. The study took into account the influence of BA on the content of the total forms of heavy metals (Metot) and their available forms (Meav). In the soil without the addition of metals, a significant increase in the content of Cdtot and Cdav, and a decrease in the content of Zntot were observed due to the application of BA. The addition of metals against the background of the BA used resulted in a significant increase in Cdtot, Pbtot, and Zntot, as well as an increase in the available forms of Pbav but a decrease in Znav. However, there was no significant increase in the Cdav content. The obtained results may indicate the potentially immobilizing role of BA only in the case of zinc. They may constitute the basis for further, more detailed research aimed at determining the role of BA in the immobilization of various metals in soil.