Light-emitting Electrochemical Cells Devices Research Articles

Efficiency Roll-Off in Light-Emitting Electrochemical Cells.

Understanding "efficiency roll-off" (i.e., the drop in emission efficiency with increasing current) is critical if efficient and bright emissive technologies are to be rationally designed. Emerging light-emitting electrochemical cells (LECs) can be cost- and energy-efficiently fabricated by ambient-air printing by virtue of the in situ formation of a p-n junction doping structure. However, this in situ doping transformation renders a meaningful efficiency analysis challenging. Herein, a method for separation and quantification of major LEC loss factors, notably the outcoupling efficiency and exciton quenching, is presented. Specifically, the position of the emissive p-n junction in common singlet-exciton emitting LECs is measured to shift markedly with increasing current, and the influence of this shift on the outcoupling efficiency is quantified. It is further verified that the LEC-characteristic high electrochemical-doping concentration renders singlet-polaron quenching (SPQ) significant already at low drive current density, but also that SPQ increases super-linearly with increasing current, because of increasing polaron density in the p-n junction region. This results in that SPQ dominates singlet-singlet quenching for relevant current densities, and significantly contributes to the efficiency roll-off. This method for deciphering the LEC efficiency roll-off can contribute to a rational realization of all-printed LEC devices that are efficient at highluminance.

Synthesis and Characterization of Iridium(III) Complexes with Substituted Phenylimidazo(4,5-f)1,10-phenanthroline Ancillary Ligands and Their Application in LEC Devices.

In this work, we report on the synthesis and characterization of six new iridium(III) complexes of the type [Ir(C^N)2(N^N)]+ using 2-phenylpyridine (C1-3) and its fluorinated derivative (C4-6) as cyclometalating ligands (C^N) and R-phenylimidazo(4,5-f)1,10-phenanthroline (R = H, CH3, F) as the ancillary ligand (N^N). These luminescent complexes have been fully characterized through optical and electrochemical studies. In solution, the C4-6 series exhibits quantum yields (Ф) twice as high as the C1-3 series, exceeding 60% in dichloromethane and where 3MLCT/3LLCT and 3LC emissions participate in the phenomenon. These complexes were employed in the active layer of light-emitting electrochemical cells (LECs). Device performance of maximum luminance values of up to 21.7 Lx at 14.7 V were observed for the C2 complex and long lifetimes for the C1-3 series. These values are counterintuitive to the quantum yields observed in solution. Thus, we established that the rigidity of the system and the structure of the solid matrix dramatically affect the electronic properties of the complex. This research contributes to understanding the effects of the modifications in the ancillary and cyclometalating ligands, the photophysics of the complexes, and their performance in LEC devices.

Hydrophilic Conjugated Polymers for Sustainable Fabrication of Deep‐Red Light‐Emitting Electrochemical Cells

AbstractIt is crucial to develop functional electronic materials that can be processed from green solvents to achieve environmentally sustainable and cost‐efficient printing fabrication of organic electronic devices. Here, the design and cost‐efficient synthesis of two hydrophilic and emissive conjugated polymers, TQ‐OEG and TQ2F‐OEG, are presented, which are rendered hydrophilic through the grafting of oligo(ethylene glycol) (OEG) solubilizing groups onto the thiophene‐quinoxaline conjugated backbone and thereby can be processed from a water:ethanol solvent mixture. The results show that the introduction of the OEG groups enables for a direct dissolution of salts by the neat polymer for the attainment of solid‐state ion mobility. These properties are utilized for the design and development of light‐emitting electrochemical cells (LECs), the active materials of which can be solution cast from a water:ethanol‐based ink. It is specifically shown that such an LEC device, comprising an optimized blend of the TQ2F‐OEG emitter and a Li salt as the active material positioned between two air‐stabile electrodes, delivers deep‐red emission (peak wavelength = 670 nm) with a radiance of 185 µW m−2 at a low drive voltage of 2.3 V. This study contributes relevant information as to how polymers and LEC devices can be designed and fabricated to combine functionality with sustainability.

Introducing MR‐TADF Emitters into Light‐Emitting Electrochemical Cells for Narrowband and Efficient Emission

AbstractOrganic semiconductors that emit by the process of multi‐resonance thermally activated delayed fluorescence (MR‐TADF) can deliver narrowband and efficient electroluminescence while being processable from solvents and metal‐free. This renders them attractive for use as the emitter in sustainable light‐emitting electrochemical cells (LECs), but so far reports of narrowband and efficient MR‐TADF emission from LEC devices are absent. Here, this issue is addressed through careful and systematic material selection and device development. Specifically, the authors show that the detrimental aggregation tendency of an archetypal rigid and planar carbazole‐based MR‐TADF emitter can be inhibited by its dispersion into a compatible carbazole‐based blend host and an ionic‐liquid electrolyte, and it is further demonstrated that the tuning of this active material results in a desired balanced p‐ and n‐type electrochemical doping, a high solid‐state photoluminescence quantum yield of 91%, and singlet and triplet trapping on the MR‐TADF guest emitter. The introduction of this designed metal‐free active MR‐TADF material into a LEC, employing air‐stabile electrodes, results in bright blue electroluminescence of 500 cd m−2, which is delivered at a high external quantum efficiency of 3.8% and shows a narrow emission profile with a full‐width‐at‐half‐maximum of 31 nm.

The Effect of the Interface Layer on the Electronic Parameters of the Light Emitting Electrochemical Cell (LEC) Device Based on Iridium (III) Complex that Calculated by Different Methods

We report a calculation of the electronic parameters and some optical measurement results of a light-emitting electrochemical cell (LEC), one of the most basic forms of electroluminescent films by modifying 4-(4-methoxy-N-naphthalen-1-ylanilino) benzoic acid (MA) as hole injection layer doped with an emissive layer that is ionic transition metal complex (Ir[dF(CF3)ppy]2(dtbpy))PF6-(Ir-iTMC). The electronic parameters of LEC device were computed using three different methods; Cheung and Cheung’s, Conventional Schottky and Norde, to evaluate the ideality factor (n), the barrier height () and the series resistance (Rs) of the LEC device. The formation on indium tin oxide (ITO) substrate was analyzed by Atomic Force Microscopy (AFM). The HOMO-LUMO energy level and electronic charge distribution of the MA molecule were computed theoretically using Chemissian software. The MA’s HOMO-LUMO energy level is determined to be EHOMO = −5.27 eV and ELUMO = −1.40 eV. The ITO surface has been modified with the Self-Assembled Monolayers (SAM) technique as an interlayer to improve the surface working function by simplifying hole injection from the ITO anode to the Hole Transport Layer (HTL) in the LEC. The Ir- iTMC complexes containing Π-conjugated bridging ligand shown better external quantum efficiency (EQE), reaching to 1.49%. The max luminance values of the bare-LEC and LEC-MA are measured as 145 cd m−2 and 1240 cd m−2, respectively.

In Situ Determination of the Orientation of the Emissive Dipoles in Light‐Emitting Electrochemical Cells

AbstractThe orientation of the emissive dipoles in thin‐film devices is important since it strongly affects the light outcoupling and thereby the device emission efficiency. The light‐emitting electrochemical cell (LEC) is particularly interesting in this context because its emissive dipoles are located in a high electric‐field p‐n junction, which is formed in situ by redistribution of bulky ions. This implies that the dipole orientation could be distinctly different in the driven LEC compared to the pristine device. This study develops the destructive‐interference microcavity method for the accurate in situ determination of the orientation of the emissive dipoles during LEC operation and apply it on a common LEC device comprising an amorphous conjugated polymer termed Super Yellow as the emitter. It is found that ≈95% of the emissive dipoles are oriented in the horizontal direction with respect to the thin‐film plane in both the pristine LEC and during steady‐state light emission. This finding is attractive since it enables for efficient outcoupling of the generated photons, and interesting because it shows that a horizontal orientation of the emissive dipoles can remain despite the existence of a strong perpendicular electric field and the nearby motion of bulky ions during LEC operation.

Exploring the Electroluminescent Applications of Imidazole Derivatives.

Recently, the fields of organic light-emitting diodes (OLEDs) and light-emitting electrochemical cells (LECs) have improved tremendously with regard to tunable emission, efficiency, brightness, and thermal stability. Imidazole derivatives are excellent deep blue-green light-emitting layers in the OLED or LEC devices. This Review summarizes the major breakthroughs of various electroluminescence (EL) layers with imidazole-containing organic or organometallic derivatives, the molecular design principles, and their light-emitting performances as effective EL materials. The highly tunable chemical structures and flexible molecular design strategies of imidazole-based compounds are advantages that provide great opportunities for researchers. They can provide a good basis for the design and development of new EL materials with narrower emission and higher efficiency. Moreover, imidazole compounds have demonstrated breakthrough performances in thermally activated delayed fluorescence (TADF) properties where triplet excitons are utilized to inhibit anti-intersystem quenching, showing great promise in breaking the theoretical external quantum efficiencies (EQE) limits in traditional fluorescent devices.

Biphenyl Au(III) Complexes with Phosphine Ancillary Ligands: Synthesis, Optical Properties, and Electroluminescence in Light-Emitting Electrochemical Cells.

A series of ten cationic complexes of the general formula [(C^C)Au(P^P)]X, where C^C = 4,4'-di-tert-butyl-1,1'-biphenyl, P^P is a diphosphine ligand, and X is a noncoordinating counteranion, have been synthesized and fully characterized by means of chemical and X-ray structural methods. All the complexes display a remarkable switch-on of the emission properties when going from a fluid solution to a solid state. In the latter, long-lived emission with lifetime τ = 1.8-83.0 μs and maximum in the green-yellow region is achieved with moderate to high photoluminescence quantum yield (PLQY). This emission is ascribed to an excited state with a mainly triplet ligand-centered (3LC) nature. This effect strongly indicates that rigidification of the environment helps to suppress nonradiative decay, which is mainly attributed to the large molecular distortion in the excited state, as supported by density functional theory (DFT) and time-dependent DFT (TD-DFT) computation. In addition, quenching intermolecular interactions of the emitter are avoided thanks to the steric hindrance of the substituents. Emissive properties are therefore restored efficiently. The influence of both diphosphine and anion has been investigated and rationalized as well. Using two complexes as examples and owing to their enhanced optical properties in the solid state, the first proof-of-concept of the use of gold(III) complexes as electroactive materials for the fabrication of light-emitting electrochemical cell (LEC) devices is herein demonstrated. The LECs achieve peak external quantum efficiency, current efficiency, and power efficiency up to ca. 1%, 2.6 cd A-1, and 1.1 lm W-1 for complex 1PF6 and 0.9%, 2.5 cd A-1, and 0.7 lm W-1 for complex 3, showing the potential use of these novel emitters as electroactive compounds in LEC devices.

Phenanthroimidazole as molecularly engineered switch for efficient and highly long-lived light-emitting electrochemical cell

Light-emitting electrochemical cells (LECs) based on Ir(III) complexes owing to the superior advantages exhibit high potential for display and lighting applications. Herein, a series of Ir(III) complexes based on phenanthroimidazole (PI) as an ancillary ligand were synthesized to achieve efficient and highly stable yellow-to-orange LEC devices with fast response. These complexes exhibit appropriate electrochemical stability and significant suppression of concentration quenching in the thin films compared to the archetype complex. The fabricated LECs showed remarkably long device lifetimes over 1400 and 2100 h and external quantum efficiency of 2 and 3% for yellow and orange-LECs, respectively. The obtained t1/2 for yellow LEC is much higher than archetype [Ir(ppy)2(phen)]+ and their phenanthroline-based analogues reported so far. The incorporation of an ionic tethered functional group on PI, improved the mobility of the emissive layer and reduced the device turn-on time by 75–88%. This study shows a facile functionalization and characterization of the PI ligand as well as its potential application in optoelectronic devices (OLED).

Ion transfer into solution-processed electrodes can significantly shift the p–n junction and emission efficiency of light-emitting electrochemical cells

A light-emitting electrochemical cell (LEC) comprises mobile ions in its active material, which enable for in situ formation of a p–n junction by electrochemical doping. The position of this emissive p–n junction in the interelectrode gap is important, because it determines whether the emission is affected by constructive or destructive interference. An appealing LEC feature is that the entire device can be fabricated by low-cost solution-based printing and coating. Here, we show, somewhat unexpectedly, that the replacement of conventional vacuum-deposited indium-tin-oxide (ITO) for the positive anode with solution-processed poly(3,4-ethylenedioxythiophene):poly(styrene-sulfonate) (PEDOT:PSS) can result in an increase in the peak light-emission output by 75%. We demonstrate that this emission increase is due to that the p–n junction shifts from a position of destructive interference in the center of the interelectrode gap with ITO to a position of constructive interference closer to the anode with PEDOT:PSS. We rationalize the anodic p–n junction shift by significant anion transfer into the soft and porous PEDOT:PSS electrode during LEC operation, which is prohibited for the ITO electrode because of its compact and hard nature. Our study, thus, contributes with important design criteria for the attainment of efficient light emission from solution-processed LEC devices.

The Effect of Interface Modification by PEDOT: PSS on the Hole Mobility of the LEC Device

The purpose of the work is to understand how to effect the interface PEDOT: PSS on the hole mobility of the LEC device by Space Charge Limited Current (SCLC) approaches technique. PEDOT: PSS plays a significant role in organic electronics device as interface modification, particularly on Light-emitting electrochemical cells (LEC) due to fundamental structure of hole only device. This study analyses the hole mobility of the device based on current-voltage characteristic approach at room temperature. It has been observed that the PEDOT: PSS interface increases the hole mobility of the LEC device by a factor of 108 .

Two in One: A Dinuclear Ru(II) Complex for Deep-Red Light-Emitting Electrochemical Cells and as an Electrochemiluminescence Probe for Organophosphorus Pesticides.

The emissive properties of two Ru(II) complexes, [Ru(dmbipy)2L1][PF6]2 (1) and [Ru2(dmbipy)4L2][PF6]4 (2), (where L1 and L2 are π-extended phenanthroline-based ligands and dmbipy = 4,4'-dimethyl-2,2'-bipyridine) have been explored for dual applications, namely, deep-red light-emitting electrochemical cells (LECs) and electrochemiluminescence (ECL) sensors for the detection of organophosphorus pesticides (OPs) that include chlorpyrifos (CPS). A simple single-layer deep-red LEC device comprising 2 is reported that outperforms both its mononuclear derivative 1 and all previously reported dinuclear LECs, with a maximum brightness of 524 cd/m2, an external quantum efficiency of 0.62%, and a turn-on voltage of 3.2 V. Optoelectronic studies reveal that the ECL response of 2 is improved when compared to its mononuclear counterpart 1 and benchmark [Ru(bipy)3]2+ (3). Modified glassy carbon electrodes coated with 2 are highly sensitive deep-red ECL sensors that facilitate the detection of CPS directly from river water and fruit samples without any complex pretreatment steps, operating over a broad logarithmic concentration range, with a low detection limit.

Effect of Optical and Morphological Control of Single-Structured LEC Device.

We investigated the performance of single-structured light-emitting electrochemical cell (LEC) devices with Ru(bpy)3(PF6)2 polymer composite as an emission layer by controlling thickness and heat treatment. When the thickness was smaller than 120–150 nm, the device performance decreased because of the low optical properties and non-dense surface properties. On the other hand, when the thickness was over than 150 nm, the device had too high surface roughness, resulting in high-efficiency roll-off and poor device stability. With 150 nm thickness, the absorbance increased, and the surface roughness was low and dense, resulting in increased device characteristics and better stability. The heat treatment effect further improved the surface properties, thus improving the device characteristics. In particular, the external quantum efficiency (EQE) reduction rate was shallow at 100 °C, which indicates that the LEC device has stable operating characteristics. The LEC device exhibited a maximum luminance of 3532 cd/m2 and an EQE of 1.14% under 150 nm thickness and 100 °C heat treatment.

Evidence and Effects of Ion Transfer at Active‐Material/Electrode Interfaces in Solution‐Fabricated Light‐Emitting Electrochemical Cells

AbstractThe light‐emitting electrochemical cell (LEC) allows for energy‐ and cost‐efficient printing and coating fabrication of its entire device structure, including both electrodes and the single‐layer active material. This attractive fabrication opportunity is enabled by the electrochemical action of mobile ions in the active material. However, a related and up to now overlooked issue is that such solution‐fabricated LECs commonly comprise electrode/active‐material interfaces that are open for transfer of the mobile ions, and it is herein demonstrated that a majority of the mobile anions in a common spray‐coated active material can transfer into a spray‐coated poly(3,4‐ethylenedioxythiophene):poly(styrene‐sulfonate) (PEDOT:PSS) positive electrode during LEC operation. Since it is well established that the mobile ion concentration in the active material has a profound influence on the LEC performance, this significant ion transfer is an important factor that should be considered in the design of low‐cost LEC devices that deliver high performance.

Enhancing carrier injection efficiency of light-emitting electrochemical cells based on Cationic Ir(III) complexes by interface modification

Light-emitting electrochemical cells (LECs) have the advantages of simple structure, low driving voltage, and low packaging requirements. However, due to the different mobility of electrons and holes in emission layer, exciton quenching is inevitable caused by carrier imbalance. In this work, a red light cationic Ir(Ⅲ) complexes [Ir(tBuPBI)2(qibi)]PF6 (R) was used as the luminescent materials for the LECs, and we use the doping of MoOx into poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) layer to lower the energy barrier between complexes R and anode. In combination with the introduction of Al/LiF composite cathode, the carrier injection efficiency of the LECs is significantly improved, leading to the enhanced balance of carrier injection. In particular, high electron injection efficiency would significantly contribute to the device improvement based on the complexes with hole-preferred transporting characteristic. With enhanced carrier injection, the recombination region of the carrier is located near the center of emission layer, and the exciton quenching near the electrode will be significantly alleviated. The maximum external quantum efficiency of the LEC device is as high as 11.77%, which is 1.3 time that of the standard device. The half-lifetime of the device is 690 min, which is about 1.37 times of that of the standard device.

An Amorphous Spirobifluorene‐Phosphine‐Oxide Compound as the Balanced n‐Type Host in Bright and Efficient Light‐Emitting Electrochemical Cells with Improved Stability

AbstractA rational host–guest concept design for the attainment of high efficiency at strong luminance from light‐emitting electrochemical cells (LECs) by suppression of exciton‐polaron quenching [Tang et al., Nature Communications 2017, 8, 1190] has been reported. However, a practical drawback with the presented host–guest LEC devices was that the operational stability is insufficient for many applications. Here, a systematic study is performed, revealing that a major culprit for the limited operational stability is that the employed n‐type host, 1,3‐bis[2‐(4‐tert‐butylphenyl)‐1,3,4‐oxadiazo‐5‐yl]benzene (OXD‐7), has a strong propensity for crystallization and that this crystallization results in a detrimental phase separation of the constituents in the active material during device operation. The authors, therefore, identify an alternative class of concept‐functional n‐type hosts in the form of spirobifluorene‐phosphine‐oxide compounds, and report that the replacement of OXD‐7 with amorphous 2,7‐bis(diphenylphosphoryl)‐9,9′‐spirobifluorene results in a much improved operational lifetime of 700 h at >100 cd m−2 during constant‐bias driving at an essentially retained high current efficacy of 37.9 cd A−1 and a strong luminance of 2940 cd m−2.

Reconfigurable Perovskite LEC: Effects of Ionic Additives and Dual Function Devices

AbstractHybrid organic–inorganic perovskite light‐emitting devices (LEDs) have recently shown the characteristic dynamical behavior of light‐emitting electrochemical cells (LECs), with intrinsic ionic migration creating an electric double layer and internal p‐i‐n structure and by accumulation of ions at interfaces. Therefore, the development of perovskite light‐emitting and photovoltaic devices based on the concepts of LEC operation attracts much attention and clarifies general physical processes in perovskites. Here, new directions that can further improve perovskite optoelectronic devices and extend their functionalities using additive mobile ions are overviewed: 1) enhancing single‐layer LECs with lithium additives for increased efficiency and longer lifetime; 2) facilitating ionic motion in three‐layer perovskite LECs to create dual‐functional devices, operating as both LEC and solar cells; and 3) creating truly ambipolar LEC devices with carbon nanotubes as stable electrodes that leverage ionic doping. Taken together, the use of these approaches provides a strategy to create efficient, stable, and bright LECs, which use advantages of both LED and LEC operation. It is discussed that how the LEC behavior in perovskite LEDs can be further improved to address the long‐term challenges in perovskite optoelectronics, such as stability, through approaches like ionically reconfigurable host/guest systems.

Film Conductivity Affects the Electric Double Layer Formation in Iridium-based Light-emitting Electrochemical Cells

Light-emitting electrochemical cells (LEECs) from ionic transition metal complexes (iTMCs) are promising candidates for low-cost lighting system because they are easy to make using solution-based technologies and air-stable materials with simple architecture. Typically, they are fabricated as single-layer devices whose active region acts as mixed conductor as well as the emissive layer. Once the LEEC device is applied with a bias, ions redistribute and accumulate near the electrodes to form electric double layers (EDLs). The EDLs facilitate facile charge carrier injections that lead to efficient operation of the devices. In this work, iridium(III)- based LEEC devices of various active layer thickness were fabricated via spin coating. We investigated the connection between the initial responses of sandwich LEECs and the width of EDL that formed in the devices. Electrochemical impedance spectroscopy (EIS) revealed that the film conductivity decreases with film thickness. Operating the devices with constant bias showed that the turn-on time increases and the rate of current growth decreases as the active layer thickness of the device is increased. By formulating the device operation into an equivalent circuit and then extracting the device parameters, it was revealed that the width of EDL follows with the film thickness, which was also confirmed by the ionic charge transport modeling studies. In addition, the device modeling studies also showed that the difference in the mobility between the anions and cations can contribute to the asymmetry of the EDL effective width that formed near each electrode. Overall, this work reports that the width of the EDL formed in iridium-based LEECs is affected by the film conductivity.

Optically Pumped Lasing in Microscale Light-Emitting Electrochemical Cell Arrays for Multicolor Displays.

Laser displays, which offer wide achievable color gamut and excellent color rendering, have emerged as a promising next-generation display technology. Constructing display panels composed of pixelated microlaser arrays is of great significance for the actualization of laser displays in the flat-panel sector. Here, we report microscale light-emitting electrochemical cell (LEC) arrays that operate as both optically pumped lasers and electroluminescence devices, which can be applied as self-emissive panels for high quality displays. Optically pumped red, green, and blue laser emissions were achieved in individual circular microcells consisting of corresponding conjugated polymers and electrolytes, suggesting that the microstructures can act as resonators for coherent outputs. As-prepared microstructures possess a narrowed recombination region, which dramatically increases the current density by 3 orders of magnitude under pulsed operation, compared with the corresponding thin-film devices, representing a promising solution-processed device platform for electrical pumping. Under programmable electrical excitation, both static and dynamic displays were demonstrated with such microscale LEC arrays as display panels. The prominent performance of the demonstrated structures (microlaser arrays embedded in LEC devices) provide us deep insight into the concepts and device constructions of electrically driven laser displays.

Polymer Featuring Thermally Activated Delayed Fluorescence as Emitter in Light-Emitting Electrochemical Cells.

Semiconducting polymers that feature thermally activated delayed fluorescence (TADF) can deliver a much desired combination of high-efficiency and metal-free electroluminescence and cost-efficient solution-based fabrication. A TADF polymer is thus a very good fit for the emitting compound in light-emitting electrochemical cells (LECs) because the commonly employed air-stabile and few-layer LEC architecture is well suited for such solution-based fabrication. Herein we report on the first LEC device based on a TADF polymer as the emitting species, which delivers a luminance of 96 cd m–2 at 4 V and a current efficacy of 1.4 cd A–1 and >600 cd m–2 at 6 V, which is competitive with the performance of multilayer organic light-emitting diodes based on the same TADF polymer. We further utilize the established sensitivity of the emission of the TADF polymer to its environment to draw conclusions on the exciton populations in host-guest and host-free TADF LEC devices.