Leakage Hole Research Articles

Air leakage mechanism and hole sealing technology in directional long-drilled perimeter rock-borehole composite fissures: for gas enrichment in varying coal-seam thickness change areas

The issue of gas enrichment in the tectonic zone of coal seams, which poses significant threats to coal mine safety and leads to gas disasters, is primarily addressed through borehole extraction. The quality of this extraction is notably influenced by air leakage and sealing technologies used during drilling. To tackle the problem of gas leakage in directional long boreholes within the floor, a composite fissure leakage model for the surrounding rock and borehole is developed. This model inverts the characteristics of coal seam thickness variations and abnormal gas enrichment through heterogeneous geostatistical modeling. It enables the quantitative characterization of the air leakage mechanism in directional long boreholes of the bottom plate and proposes an effective sealing process. Due to damage and disturbance, fissures and irregular plastic zones form around the excavated roadway, which are major contributors to air leakage. Over time, the air content in the coal and rock seams gradually increases while the gas content and concentration decrease continuously. Compared to the polyurethane "two plugs and one injection" sealing process, the multi-stage grouting and sealing process provides a more stable gas extraction concentration and flow rate in the sealed drill holes. This process effectively seals the fissure zones of the roadway, reduces air leakage from the boreholes, and improves gas extraction concentration.

Improved hole injection for AlGaN-based DUV LEDs with graded-composition multiple quantum barrier insertion layers

The primary impediments to achieving high external quantum efficiency (EQE) and light output power (LOP) in AlGaN-based deep-ultraviolet light-emitting diodes (DUV LEDs) are inadequate hole injection efficiency and pronounced electron leakage. The significant polarization-induced positive charges, originating from the discontinuity in the Al composition between the last quantum barrier (LQB) and electron-blocking layer (EBL), attract electrons, consume holes, and reflect holes back into the p-type region, leading to severe electron leakage and low hole injection efficiency. In this paper, we introduce a graded-composition multiple quantum barrier (GQB) structure at the LQB/EBL interface. We adjust the Al composition in the insertion layer to alter the electrical polarity of the polarization-induced sheet charges, thereby modifying the electric field distribution in the EBL, LQB, and inserted GQB structure. Consequently, holes acquire boosted energy during their migration towards the active region. In addition, we enhance the hole injection and electron confinement ability via reducing the effective valence band barrier height and increasing the effective conduction band barrier height, thus diminishing the possibility of electron leakage from the active region into the p-type region. Therefore, the GQB structure proposed in this study provides a promising approach to improving the optical and electrical performance of DUV LEDs.

Underwater Structurally‐Colored Adhesives for Visualized Adhesion Monitoring in Aqueous Media

AbstractAssessment of the local strain/stress changes of adhesives is highly desirable for their service to avoid premature failure. However, monitoring local strain/stress variations in adhesives in practical settings remains challenging, especially in aqueous media. Here, an underwater structurally‐colored adhesive for visualized local strain/stress monitoring in aqueous media is reported. The structurally‐colored adhesive is obtained by shearing composites of poly(butyl acrylate‐co‐acrylic acid) copolymer and carboxylated polystyrene colloidal particles. The resultant structurally‐colored adhesive exhibits underwater adhesive strength (i.e., 238 kPa for stainless steel substrates) to various substrates (e.g., metals and plastics) thanks to hydrophobic segments and carboxyl groups. Notably, they can shift color in response to external force, enabling real‐time visual monitoring of localized strain/stress changes. As a proof of concept, the structurally‐colored adhesive can be used to seal a leaking hole on a bottle or tube, and it can precisely visualize the localized pressure distribution, providing critical information on the adhesion performance and the local pressure. These distinctive properties make the structurally‐colored adhesive suitable for application in wet environments as a real‐time visual pressure tracking device.

Air temperature characteristics of cable-girder pin joint node of suspension bridge under pool fire

Under the action of high temperature, the mechanical properties of steel structure will be reduced. Cable-girder pin joint nodes (referred to as the node) of suspension bridges are composed of steel structures. Before studying the fire resistance of structures, it is necessary to accurately predict the air temperature characteristics under fire. In this paper, the FDS calculation model of the node is established for the pool fire. The air temperature characteristics of the node are clarified by numerical simulation and theoretical analysis. The effects of main factors such as fire location, wind speed, leakage hole radius and space height are studied. The unfavorable fire scenario and air heating mathematical model are obtained. The main conclusions are as follows: (1) As the fire source distance increases, the peak value of air temperature at the node gradually decreases, while the heating time steadily increases and eventually reaches a stable state. (2) The air temperature at the node initially increases and then gradually decreases as the wind speed increases. (3) Increasing the leakage hole radius from 0.02 m to 0.06 m results in a decrease of approximately 60 % in the air heating time at the node. (4) Increasing the space height from 0.25 m to 1.7 m leads to a maximum decrease of 72 % in air temperature at the node. (6) In the unfavorable fire scenario, the peak air temperature at the node can reach approximately 1200 °C, and the heating time ranges from 67 s to 149 s (7) A mathematical model of the air temperature rise curve, considering the influence of space height, is developed. This model can serve as a theoretical foundation and reference for the study of fire resistance of the node exposed to pool fires.

Analysis of Leakage and Diffusion Characteristics and Hazard Range Determination of Buried Hydrogen-Blended Natural Gas Pipeline Based on CFD.

Injecting hydrogen into natural gas pipelines is an economical and efficient method of hydrogen transportation. However, the addition of hydrogen leads to significant hydrogen corrosion and embrittlement in the pipelines, especially in harsh and concealed underground conditions, where leak accidents are frequent and difficult to detect. This Article uses Le Chatelier's Principle to determine the hazardous range of hydrogen-blended natural gas (HBNG) by employing numerical simulation, it examines the gas leakage and diffusion characteristics before and after hydrogen injection as well as under different hydrogen blending ratio (HBR). Additionally, considering the density of the mixed gas, a prediction model for the diffusion hazard range of hydrogen-mixed natural gas is established based on multivariate regression theory. The results show that after a leakage occurs in HBNG the diffusion range in soil is wider compared to methane, with higher corresponding pressure and velocity values. Moreover, as the HBR increases, the farthest danger range (FDR) of the HBNG also increases. When the leakage of the buried HBNG pipeline occurs for 1 min, the difference in FDR between HBR 25% and HBR 5% is 0.005 m. After 30 min, this difference increases to 0.019 m, indicating that with longer leakage duration, the potential explosion risk resulting from increased HBR becomes greater. Factors such as pipeline pressure increase, larger leak hole size, and decreased burial depth all contribute to an increase in FDR, with pipeline pressure change having the greatest impact and burial depth change having the smallest impact. The maximum error of the predicted model for the diffusion hazard range of hydrogen-mixed natural gas is 9.385%, and the average error is 2.376%, demonstrating the accuracy of the prediction results. This study provides guidance for monitoring underground hydrogen-blended natural gas pipeline leaks, offers a basis for determining the repair range of pipelines, and ensures the safe transportation of hydrogen-mixed natural gas pipelines.

An review of research on liquid hydrogen leakage: regarding China’s hydrogen refueling stations

Hydrogen is regarded as the premier energy source for future sustainability and renewability. However, its distinct physicochemical properties render it prone to explosions in the event of a leak. Therefore, there is a need for more comprehensive research dealing with hydrogen leakage, explosion scenarios, and risk assessment. This paper provides an overview of the current hydrogen policies adopted in China. It reviews the processes of hydrogen refueling station construction and the thermophysical mechanisms of liquid hydrogen leakage. In this regard, the effects of various factors, including leakage rate, leakage time, leakage hole size, wind direction and speed, and building location, on the hydrogen leakage rate are analyzed and evaluated. Additionally, the impacts of different factors on hydrogen explosion overpressure are reported, including hydrogen concentration, wind speed, obstacles, and ignition position, in addition to the current applications of quantitative risk assessment methods in hydrogen refueling stations. Finally, the limitations of current research on liquid hydrogen leakage and explosion accidents are highlighted, along with the shortcomings of current risk assessment methods for liquid hydrogen refueling stations.

Evolution law of flow characteristics for straight pipeline after leaking

Aiming at the leakage problem of the fluid loop system for the thermal control system of spacecraft caused by the impact of micro-meteoroid and orbital debris, we investigate the dependence of the leak rate, pressure drop and flow characteristics before and after leaking on leak position, inlet pressure, and leaking aperture, calculated in a straight pipeline with single leakage, using stationary and transient three-dimensional computational fluid dynamics simulations with commercial software (FLUENT). The working fluid adopts single-phase water without gravity. It is found that the pressure increases obviously near the leak point, which is caused by the local peak of pressure. As the length between the leak point and the inlet becomes larger, the local peak of pressure and the dimensionless leak rate are smaller. When the inlet pressure increases, the leaked mass flow rate increases; however, the ratio of the leaked flow rate to inlet flow rate decreases. Furthermore, it is observed that the dependence of dimensionless leaking rate on dimensionless leaking aperture has a scaling relation with the scaling exponent approximating to 2, which may be related to the proportion of the vortex formed by the backward flow at the leak hole, the amplitude, and the affected length along the pipe of the local peak of pressure. This study is instructive and meaningful to the leak detection and plugging of fluid loop in space.

379. SUCCESSFUL MANAGEMENT OF ANASTOMOTIC LEAKAGE FOLLOWING ESOPHAGECTOMY USING ENDO-VACUUM ASSISTED CLOSURE (EVAC) THERAPY: A CASE REPORT

Abstract Background Esophagectomy is a crucial curative treatment for potentially resectable esophageal cancer. However, anastomotic leakage poses a significant complication, with reported incidences ranging from 11.4% to 21.2% and mortality rates between 7.2% and 35%. Endoluminal or cavitary type of vacuum therapy (EVAC) represents a minimally invasive approach adapted from negative pressure wound closure techniques. Our case demonstrates the successful application of EVAC in managing a significant postoperative leak. Methods A 70-year-old male who underwent esophagectomy for early esophageal cancer. On postoperative day 23, a 20mm-sized large anastomotic leakage was detected, leading to the insertion of Endo-VAC for treatment. Endoscopically exchange was regularly. Results Endoscopically exchange was performed seven times, gradually reducing the size of the leakage hole. In the end, the anastomotic leakage was completely healed, and the patient was discharged on postoperative day 86. The patient id currently undergoing outpatient follow-up with no recurrence or metastasis of the disease confirmed. Conclusion Through our case, we highlight the potential suitability of EVAC therapy as a less invasive and effective treatment modality for anastomotic leakage following esophagectomy. This approach may be considered as a priority treatment for anastomotic leak.

Dual polarization for efficient III-nitride-based deep ultraviolet micro-LEDs

The deep ultraviolet (DUV) micro-light emitting diode (μLED) has serious electron leakage and low hole injection efficiency. Meanwhile, with the decrease in the size of the LED chip, the plasma-assisted dry etching process will cause damage to the side wall of the mesa, which will form a carrier leakage channel and produce non-radiative recombination. All of these will reduce the photoelectric performance of μLED. To this end, this study introduces polarized bulk charges into the hole supply layer (p-HSL) and the electron supply layer (n-ESL) respectively (dual-polarized structure) of the DUV μLED at an emission wavelength of 279 nm to enhance the binding of carriers and increase the injection efficiency of carriers. This is because the polarization-induced bulk charge can shield the polarized sheet charge on the interface and reduce the polarization electric field. The reduced polarization electric field in p-HSL can increase the effective barrier height of the conduction band in the p-type region and reduce the effective barrier height of the valence band. The decrease in the polarized electric field of n-HSL can reduce the thermal velocity of electrons, thereby enhancing the electron injection efficiency, reducing the Shockley–Read–Hall (SRH) recombination, and increasing the effective barrier height of the valence band. The study results indicate that the electron concentration and hole concentration of a μLED with dual polarization were increased by 77.93% and 93.6%, respectively. The optical power and maximum external quantum efficiency of μLED reached 31.04 W/cm2 and 2.91% respectively, and the efficiency droop is only 2.06% at 120 A/cm2. These results provide a new approach to solving the problem of insufficient carrier injection and SRH recombination in high-performance DUV μLEDs.

Under-expanded jet and diffusion characteristics for small-hole leakage of hydrogen-blended natural gas in high-pressure pipelines

Hydrogen blending in natural gas pipelines is an economical method of hydrogen transportation, but it can increase explosion risks from leakages. Current leakage models struggle to capture under-expanded jet structures near leakage holes due to limited computational resources and cannot accurately describe explosion hazardous distances of subsequent diffusion. A two-stage model for simulating the leakage of hydrogen-blended natural gas (HBNG) pipelines is introduced, comprising jet and diffusion models. The source strength determined in the jet model serves as the inlet boundary condition for the subsequent diffusion model. The results show that considering the under-expanded jet structure can more accurately reflect the pressure fluctuation changes near the leakage hole, particularly at the location of the Mach disc, xm. The pressure at the 10xm section of the jet region stabilizes at atmospheric pressure and utilizing this value as the inlet boundary for the diffusion model prevents supersonic and oscillatory regions. Subsequently, the impact of pipeline operating pressure, leakage hole diameter, and hydrogen blending ratio (HBR) on the far-field diffusion characteristics is analyzed. Notably, the leakage hole diameter has a more pronounced effect on the explosion hazardous distance compared to other factors. This research provides insights for the prevention and management of HBNG leakage accidents.

Experimental and simulation investigation of jet characteristics during the accidental release of high-pressure CO2 with different diameter leakage orifice

Understanding the near-field characteristics of leakage is essential for safety distance calculations and risk assessment of emergency response to a pipeline leakage. This paper presents a small-scale experiment and computational fluid dynamics model designed to investigate the transient characteristics of near-field parameters. The study also analyzes the effects of leakage orifice diameter on the transient characteristics of the near-field. The results show that a pipeline leak starts with the formation of a compression wave, which causes the air at the front of the stream to be compressed, heated and pressurized. CO2 is then released at high pressure, creating a strong expansion wave that keeps the fluid pressure below local atmospheric levels. For full-hole and large-hole leaks, the temperature drop and rate show a negative linear correlation with the size of the leak hole. Conversely, for small hole leaks with the ratio of hole diameter to pipe diameter values below 0.2, the temperature drop shows an opposite trend. As the ratio of hole diameter to pipe diameter values increases, the maximum diameter of the barrel drum-shaped disk gradually increases, but the maximum expansion angle of the jet decreases. It is hoped that this work will contribute to the improvement of research models that assess the consequences of potential high-pressure pipeline rupture scenarios.

Factor analysis and GA-BP-ANN prediction of nitrogen diffusion behavior in underground laboratory under ventilation conditions

Nitrogen is widely used in various laboratories as a suppressive gas and a protective gas. Once nitrogen leaks and accumulates in a such confined space, it will bring serious threats to the experimental staff. Especially in underground tunnels or underground laboratories where there is no natural wind, the threat is more intense. In this work, the ventilation design factors and potential leakage factors are identified by taking the leakage and diffusion of a large liquid nitrogen tank in China Jinping Underground Laboratory (CJPL) as an example. Based on computational fluid dynamics (CFD) research, the effects of fresh air inlet position, fresh air velocity, exhaust outlet position, leakage hole position, leakage hole size, and leaked nitrogen mass flow rate on nitrogen diffusion behavior in specific environments are discussed in detail from the perspectives of nitrogen concentration field and nitrogen diffusion characteristics. The influencing factors are parameterized, and the Latin hypercube sampling (LHS) is used to uniformly sample within the specified range of each factor to obtain samples that can represent the whole sample space. The nitrogen concentration is measured by numerical value, and the nitrogen diffusion characteristics are measured by category. The GA-BP-ANN numerical regression and classification regression models for nitrogen concentration prediction and nitrogen diffusion characteristics prediction are established. By using various rating indicators to evaluate the performance of the trained model, it is found that models have high accuracy and recognition rate, indicating that it is effective in predicting and determining the concentration value and diffusion characteristics of nitrogen according to ventilation factors and potential leakage factors. The research results can provide a theoretical reference for the parametric design of the ventilation system.

Experimental study on the movement of oil spill under freeze-thaw action

Oil leakages cause environmental pollution, economic losses, and even engineering safety accidents. In cold regions, researchers urgently investigate the movement of oil spill in soils exposed to freeze-thaw cycles. In this study, a series of laboratory model experiments were carried out on the migration of oil leakage under freeze-thaw action, and the distributions of the soil temperature, unfrozen water content, and displacement were analyzed. The results showed that under freeze-thaw action, liquid water in soils migrated to the freezing front and accumulated. After the pipe cracked, oil pollutants first gathered at one side of the leak hole, and then moved around. The pipe wall temperature affected the soil temperature field, and the thermal influence range below and transverse the pipe wall (35–40 cm) was larger than that above the pipe wall (8 cm) owing to the soil surface temperature. The leaked oil's temperature would make the temperature of the surrounding soil rise. Oil would inhibit the cooling of the soils. Besides, oil migration was significantly affected by the gravity and water flow patterns. The freeze-thaw action would affect the migration of the oil, which was mainly manifested as inhibiting the diffusion and movement of oil when soils were frozen. Unfrozen water transport caused by freeze-thaw cycles would also inhibit oil migration. The research results would provide a scientific reference for understanding the relationship between the movement of oil pollutants, water, and soil temperature, and for establishing a water-heat-mass transport model in frozen soils.

Impact radius of light oil pipeline leakage under different operating conditions

This study investigated the impact range of pipeline leaks for light oil pipelines under different operating conditions. Three different calculation methods were employed to study the influence of various factors, including obstacle height, wind speed, leak hole diameter, and slope, on the leak impact range of flowing fires, pool fires, and overpressure waves. The results indicate that the impact range decreases as the height of obstacles increases. The most significant decrease occurs when obstacles are 2 meters high, and further increasing the obstacle height leads to a less pronounced decrease. Wind speed has a complex influence on the impact range. For flowing fires, the impact range initially increases and then decreases with higher wind speeds. For pool fires, a higher wind speed leads to a larger impact range, while for overpressure waves, higher wind speeds result in a smaller impact range. Larger leak hole diameters lead to larger impact ranges for both fire radiation and overpressure waves. Increasing the environmental slope has a slight effect on the impact range. Sensitivity analysis indicates that wind speed has the most significant impact, followed by leak hole diameter, while the environmental slope has the least influence on the impact range.

Failure analysis of leaking firefighting pipeline used in nuclear power plant: Corrosion development process and key influence factors

A penetrating hole has been found in the inner wall of the firefighting pipeline (A106 steel) used for 20 years in a nuclear power plant of China, and the pipeline is filled with almost stagnant tap water before failure. The failed pipeline is taken from a vertically placed water outlet pipeline. The corrosion process and key influence factors of the failed firefighting pipeline were studied using optical microscopy (OM), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results show that there exist two typical corrosion characteristics on the inner wall of the failed pipeline besides leakage hole, that is, corrosion nodulation and corrosion bulge. The corrosion nodulation, mainly consisting of a mixture of calcium and iron oxides, is the initiation position of perforation corrosion, and the iron-oxidizing bacteria (IOB) play a key role in the formation of corrosion nodulation. Then the sulfate-reducing bacteria (SRB) is involved in the propagation of corrosion nodulation when the dissolved oxygen concentration is low. The corrosion nodulation gradually become loose and form large bulge with extended service time. The corrosion pits under the corrosion bulge also develop gradually. Eventually, the inner wall of the pipeline is thinned and perforated.

Indoor space risk assessment based on Co-analysis strategy in split room air conditioning

The use of environmentally friendly hydrocarbon refrigerants in air conditioning systems is being promoted worldwide as a proactive measure to combat global warming and ozone depletion. A comprehensive analysis of hydrocarbon refrigerant leakage and the resulting fire risk is essential for split room air conditioning (SRAC) systems. The study presents a novel Co-analysis strategy that integrates the operation of SRAC systems with the assessment of indoor space fire risk. Experiments involving the leakage and diffusion of R-290 in SRAC system have been conducted to substantiate the validity of the Co-analysis strategy. This model is used to analyze the dynamic parameters of leakage and distribution patterns of hazardous areas within the SRAC indoor unit. The study considers various leakage hole sizes (1 mm, 2 mm, 3 mm) under both cooling and heating operating modes. The results show the leaking refrigerant flow rate presents different attenuation types under cooling and heating modes. When the leakage hole diameter is less than 2 mm in the cooling mode, the concentration of R-290 in the space is below 50 % lower flammable limit. The comprehensive fire risk probability of the R-290 indoor unit is 1.0 × 10−11∼5.0 × 10−10 for the cooling model and 1.0 × 10−11∼9.0 × 10−10 for the heating model. Effective methodologies for mitigating risks and optimizing the system are also proposed. Based on the Co-analysis strategy, this study presents a scientifically grounded assessment of the fire risk associated with air conditioning uses flammable refrigerants inside buildings. The strategy aims to enhance building safety.

Study on the impact of different hole shapes on liquefied gas leakage behavior

Accidental leakage of liquefied gas is a common occurrence during its storage, transportation, and usage. The shape of the leakage holes varies due to different causative factors. In this paper, we have established an experimental setup using R134a as the medium to simulate liquefied gas leakage. Different nozzle shapes are used to simulate the effect of various leakage hole shapes on the release process. The results indicate that, when the hole area (A) is constant, the discharge coefficient (Cd(exp)) decreases in the order of circular, square, and triangular holes. Simultaneously, based on dimensional analysis, we propose an empirical formula to predict the Cd(pre) for both circular and non-circular hole leakage. Notably, non-circular holes exhibit an axis-switching phenomenon during flash vaporization spray, leading to an asymmetric structure in the spray cone angle (θ) of triangular holes. The spray area of circular holes displays significantly larger lowest temperature and low-temperature regions compared to non-circular holes.

Investigation of Hydrogen-Blended Natural Gas Pipelines in Utility Tunnel Leakage and Development of an Accident Ventilation Strategy for the Worst Leakage Conditions

The development of hydrogen-blended natural gas (HBNG) increases the risk of gas transportation and presents challenges for pipeline security in utility tunnels. The objective of this study is to investigate the diffusion properties of HBNG in utility tunnels and evaluate the effectiveness of various ventilation mechanisms. The numerical simulation software Fluent 2023 R1 is applied to simulate and analyze the leakage of small holes in a HBNG pipeline in the natural gas compartment. By examining the leaking behavior of HBNG through small holes in different circumstances, we aimed to identify the most unfavorable operational situation for leakage. Subsequently, we analyzed the ventilation strategy for sub-high-pressure pipes at various pressure levels in this unfavorable condition. This study’s findings demonstrate that blending hydrogen improves the gas diffusion capacity and increases the likelihood of explosion. The primary factors that influence the pattern of leakage are the size of the leaking holes and the pressure of the pipeline. The gas compartment experiences the most unfavorable working conditions for natural gas pipeline leaks when there are higher pressures, wider leak openings, higher hydrogen blending ratios (HBRs), and leaks in close proximity to an air inlet. When the HBR is 20%, the minimum accident ventilation rates for pressures of 0.4 MPa and 0.8 MPa are 15 air changes per hour and 21 air changes per hour, respectively. The maximum allowable wind speed for accident ventilation is 5 m/s, as regulated by China’s national standard, GB 50838-2015. This regulation makes it difficult to minimize the risk of leakage in a 1.6 MPa gas pipeline. It is recommended to install a safety interlock device to quickly shut off the pipeline in the event of a leak in order to facilitate the dispersion of the substance.

Optimization of AlGaN-based deep ultraviolet light emitting diodes with superlattice step doped electron blocking layers.

The superlattice electron blocking layer (EBL) has been proposed to reduce the electron leakage of the deep ultraviolet light emitting diodes (DUV-LEDs). However, the hole transport is hindered by the barriers of EBL and the improvement of hole injection efficiency still suffers enormous challenges. The superlattice step doped (SLSD) EBL is proposed to improve the hole injection efficiency while enhancing the electron confinement capability. The SLSD EBL enhances the electron confinement capability by multi-reflection effects on the electron wave function. And a built-in electric field towards the active region is generated by superlattice step doping, which facilitates the transport of holes into the multiple quantum wells. The Advaced Physical Model of Semiconductor Devices (APSYS) software is used to simulate the DUV-LEDs with conventional EBL, superlattice EBL, superlattice doped EBL, and SLSD EBL. The results indicate that the SLSD EBL contributes to the increased electron concentration in the multiple quantum wells, the reduced electron leakage in the p-type region, the increased hole injection current, and the increased radiative recombination rate. When the current is 60 mA, the external quantum efficiency of DUV-LED with SLSD EBL is increased to 5.27% and the output power is increased to 13.81 mW. The SLSD EBL provides a valuable reference for solving the problems of serious electron leakage and insufficient hole injection of the DUV-LEDs.

A Quantitative Risk Analysis during Truck-to-Ship Ammonia Bunkering

A primary objective for the sustainable development of the maritime sector is to transition toward carbon-neutral fuels, with the aim to reduce emissions from maritime transportation. Ammonia emerges as a promising contender for hydrogen storage, offering the potential for CO2-free energy systems in the future. Notably, ammonia presents advantageous attributes for hydrogen storage, such as its high volumetric hydrogen density, low storage pressure requirements, and long-term stability. However, it is important to acknowledge that ammonia also poses challenges due to its toxicity, flammability, and corrosive nature, presenting more serious safety concerns that need to be addressed compared with other alternative fuels. This study sought to explore the dispersion characteristics of leaked gas during truck-to-ship ammonia bunkering, providing insights into the establishment of appropriate safety zones to minimize the potential hazards associated with this process. The research encompassed parametric studies conducted under various operational and environmental conditions, including different bunkering conditions, gas leak rates, wind speeds, and ammonia toxic doses. EFFECTS, which is commercial software for consequence analysis, was utilized to analyze specific scenarios. The focus was on a hypothetical ammonia bunkering truck of 37,000 L refueling an 8973 deadweight tonnage (DWT) service vessel with a tank capacity of 7500 m3 in the area of Mokpo Port, South Korea. The study’s findings underscore that the ammonia leak rate, ambient temperature, and wind characteristics significantly impacted the determination of safety zones. Additionally, the bunkering conditions, leak hole size, and surrounding traffic also played influential roles. This study revealed that bunkering in winter resulted in a larger safety zone compared with bunkering in summer. The lethality dose of ammonia was affected by the leak hole size, time for dispersion, and the amount of ammonia released. These observed variations imply that ammonia truck-to-ship bunkering should be undertaken with carefully chosen suitable safety criteria, thereby significantly altering the scope of safety zones. Consequently, the risk assessment method outlined in this paper is expected to assist in determining the appropriate extent of safety zones and provide practical insights for port authorities and flag states contributing to the future sustainable development of the maritime industry.