Laser-scanning Optical-resolution Photoacoustic Microscopy Research Articles

Ultrafast laser-scanning optical resolution photoacoustic microscopy at up to 2 million A-lines per second

The imaging speed of optical resolution photoacoustic microscopy (OR-PAM) using pulsed excitation is fundamentally limited by the range ambiguity condition, which defines the maximum laser pulse repetition frequency (PRF). To operate at this theoretical upper limit and maximize acquisition speed, a custom-built fiber laser capable of operating at a PRF of up to 2 MHz was combined with a fast laser scanning optical OR-PAM system based on a stationary fiber-optic ultrasound sensor. A large area (10 mm × 10 mm) of the mouse ear was imaged within 8 s, when acquiring 16 million A-lines and operating the laser at a PRF of 2 MHz. This corresponds to a factor of four improvement in imaging speed compared to the fastest OR-PAM system previously reported. The ability to operate at high-imaging frame rates also allows the capture of hemodynamic events such as blood flow. It is considered that this system offers opportunities for high throughput imaging and visualizing dynamic physiological events using OR-PAM.

Real-time GPU-accelerated processing and volumetric display for wide-field laser-scanning optical-resolution photoacoustic microscopy.

Fast signal processing and real-time displays are essential for practical imaging modality in various fields of applications. However, the imaging speed in optical-resolution photoacoustic microscopy (OR-PAM), in particular, depends on factors such as the pulse repetition rate of the laser, scanning method, field of view (FOV), and signal processing time. In the past, efforts to increase acquisition speed either focused on developing new scanning methods or using lasers with higher pulse repetition rates. However, high-speed signal processing is also important for real-time volumetric display in OR-PAM. In this study, we carried out parallel signal processing using a graphics processing unit (GPU) to enable fast signal processing and wide-field real-time displays in laser-scanning OR-PAM. The average total GPU processing time for a B-mode PAM image was approximately 1.35 ms at a display speed of 480 fps when the data samples were acquired with 736 (axial) × 500 (lateral) points/B-mode-frame at a pulse repetition rate of 300 kHz. In addition, we successfully displayed maximum amplitude projection images of a mouse's ear as volumetric images with an FOV of 3 mm × 3 mm (500 × 500 pixels) at 1.02 s, corresponding to 0.98 fps.

Concentration dependence of optical clearing on the enhancement of laser-scanning optical-resolution photoacoustic microscopy imaging

Quantitative analysis of optical clearing effects (OCE) induced by hyperosmotic agents is very important to optical tissue clearing applications in biomedical diagnostic imaging and therapeutics. This study aims at investigating the effect of glycerol concentration on the laser-scanning optical-resolution photoacoustic microscopy (LSOR-PAM) imaging contrast and light penetration depth. The photoacoustic (PA) signal amplitude changes are evaluated as a function of the concentration of glycerol. The results reveal that the PA signal amplitudes are enhanced with the glycerol concentration increasing, and also show that higher concentration of glycerol produces better light penetration and OCE on a phantom. The PA signal amplitude increases only 8.1% for 20% glycerol, but for higher concentrations, the increases are 76% and 165% for 40% and 60% glycerol, respectively. This preliminary study demonstrates that application of glycerol as an optical contrast agent reduces the tissue scattering and is beneficial to PAM imaging and optical diagnosis in clinical dermatology.

Combined photoacoustic microscopy and optical coherence tomography can measure metabolic rate of oxygen

We proposed to measure the metabolic rate of oxygen (MRO2) in small animals in vivo using a multimodal imaging system that combines laser-scanning optical-resolution photoacoustic microscopy (LSOR-PAM) and spectral-domain optical coherence tomography (SD-OCT). We first tested the capability of the multimodal system to measure flow rate in a phantom made of two capillary tubes of different diameters. We then demonstrated the capability of measuring MRO2 by imaging two parallel vessels selected from the ear of a Swiss Webster mouse. The hemoglobin oxygen saturation (sO2) and the vessel diameter were measured by the LSOR-PAM and the blood flow velocity was measured by the SD-OCT, from which blood flow rate and MRO2 were further calculated. The measured blood flow rates in the two vessels agreed with each other.

Laser-scanning optical-resolution photoacoustic microscopy

We have developed a laser-scanning optical-resolution photoacoustic microscopy method that can potentially fuse with existing optical microscopic imaging modalities. To acquire an image, the ultrasonic transducer is kept stationary during data acquisition, and only the laser light is raster scanned by an x-y galvanometer scanner. A lateral resolution of 7.8 microm and a circular field of view with a diameter of 6 mm were achieved in an optically clear medium. Using a laser system working at a pulse repetition rate of 1,024 Hz, the data acquisition time for an image consisting of 256 x 256 pixels was less than 2 min.