Larger Particle Diameter Research Articles

Image processing and neural network technique for size characterization of gravel particles

Particle size is considered one of the significant characteristics used in geotechnical practices. Traditionally, sieve analysis is utilized for coarse-grained soil. However, this method could be time consuming and take much effort, especially for large scale infrastructure projects. This paper presents an efficient method for estimating gravel particle characterization utilizing image processing and artificial neural network technique (IPNN). The proposed algorithm is performed by utilizing particle boundary delineation and shape feature extraction to train a neural network model for estimating gravel size distribution curve. It is found that excellent agreement exists between the results obtained from conventional sieve analysis and neural analysis for gravel soil particles with maximum difference in passing percentages up to only 3.70%. The proposed technique shows satisfactory results for crushed stone samples with maximum difference in passing percentages about 10.90% mainly in large diameter particles. The presented technique (IPNN) could offer a promising alternative technique for material quality control process especially in large scale projects.

Experimental study on emissions and particulate characteristics of diesel engine fueled with plastic waste oil, acetone-butanol-ethanol and diesel blends

Plastic waste poses a significant environmental challenge due to its non-biodegradable nature and accumulation in landfills. Converting plastic waste into usable fuel could offer a promising solution for mitigating these issues while addressing the emission-related challenges of diesel engines. This study investigates the impact of plastic waste oil (WPO) obtained through pretreatment and catalytic pyrolysis, blended with acetone-butanol-ethanol (ABE) and diesel fuel, on diesel engine. The aim was to evaluate how these blends affect gaseous emissions, organic compounds, and particle-bound carbon, focusing on their potential to reduce harmful pollutants compared to pure diesel fuel. The results indicated that the ABE5W15D blend significantly reduced smoke and CO emissions by 35.7 % and 17.43 %, respectively, with a slight decrease in HC emissions. However, the ABE20W blend showed elevated NOx levels due to higher ignition delay and increased cylinder pressure. Compared to pure diesel (D100), ABE10W10D and ABE5W15D blends reduced total polycyclic aromatic hydrocarbons (PAHs) emissions by 26.8 % and 37.4 %, respectively. Naphthalene was the dominant PAH, remarkably increasing with W20D use, while longer-chain alkanes associated with lubricant oil had higher W20D emissions. The ABE5W15D blend notably reduced organic carbon (OC) emissions by approximately 38.26 % compared to D100. ABE20D exhibited lower elemental carbon (EC) emissions than D100, although it had higher EC than OC. The W20D blend resulted in larger particle diameters, whereas ABE10W10D showed lower particle counts in the 7–15 nm range. In conclusion, blending plastic waste oil with ABE and diesel fuel can effectively mitigate certain pollutants, depending on the blend composition.

Numerical study on the motion of two parallel spherical particles with different diameters in upward flow

The settling of particles is related to many industrial processes and research fields. However, due to the complex particle–particle and particle–fluid interactions, the settling mechanism of particles in flowing fluids is not fully understood. This article conducts numerical research on the settling process of two particles with different diameters in parallel in upward flow using the immersion boundary method. The numerical method was validated against experimental results including one particle settling, two parallel particles settling, and two series particles settling. The effects of large particle diameter, upward flow velocity, and initial particle spacing on the settling process were explored. The results indicate that the two particles with same diameter will repel each other when settling in upward flow. Moreover, when the diameters differ, the two particles can experience both attractive and repulsive interactions. The larger the diameter of the large particle, the stronger its attractive influence on the small particle. When the diameter of large particle d2 = 3.0d1, large particle only has an attractive effect on small particle. The wake of each particle forms a distinct velocity boundary with the upward fluid. As the upward flow velocity increases, the interactions between the two particles become increasingly intense. With increasing initial spacing between the particles, their mutual interactions gradually weaken.

Increasing particle-size by air-flow modification – An experimental study

Ambient particulate are characterize by submicron particles that may penetrate deep into the lungs, where they become harmful due to their morphology and composition, or due to their role as carriers of harmful chemicals or biological agents. Particle filtration technologies have in general a lower efficiency at diameter size around 0.1–0.3 μm. This study examines the concept of particle grouping as a means to overcome this size-gap, for improving air purification or filtration systems. The grouping manipulation is induced by a controlled rotating valve which creates a sinusoidal flow in the experimental tube, and by modules with varying diameter, forcing a wavy flow. Fine particles with a known size distribution which are introduced into the manipulated flow, exhibit groups of particles in the outflow, hence increase the effective size of the particles. Former successful studies were performed with high flow velocity and particle load of industrial duct and car engine outflow, while in the current study smaller particle loads representing ambient to indoor levels are in operation. Although the low velocity and particle load are challenging, this study shows a promising shift of the particle size distribution from a peak at 0.2–0.3 μm, towards larger particle diameters. Fine powder of dolomite is used in this study and preliminary results of adhesion experiments related to dolomite are also reported.

Contact electrification characteristics of solid oxygen particle-laden flows in liquid hydrogen transportation

The issue of electrostatic safety in liquid hydrogen systems has garnered increasing attention, especially concerning the potential threat of electrostatic explosions due to the collision-electrification phenomenon of solid oxygen particles formed after air leakage in liquid hydrogen pipelines. To delve into the contact electrification characteristics of solid oxygen particle-laden flows in liquid hydrogen transportation, a mathematical model based on the computational fluid dynamics-discrete element method (CFD-DEM) two-phase flow dynamics has been developed. This model integrates the Hertz contact theory for describing particle collision processes and the condenser model for describing particle collision-electrification. The reliability of this model has been validated in existing literature through its ability to capture the flow characteristics of two-phase flow and the electrification characteristics of particle groups. Using density functional theory to compute the solid oxygen work function and considering the low-temperature properties of liquid hydrogen, a series of numerical studies on the flow sedimentation and electrification characteristics of solid oxygen particle-laden flows in liquid hydrogen pipelines have been conducted. The results indicate that particles carry negative charges after colliding with stainless steel pipe walls, with single charge exchange magnitudes of approximately 10−12C for particle-wall continuous collision processes and 10−14C for particle-particle collision processes, resulting in particle charge-to-mass ratios on the order of tens of μC/kg at the outlet interface. The impact of electrostatic forces on particle motion is significant and cannot be overlooked. Furthermore, the effects of velocity, particle diameter, and pipe diameter on particle charge characteristics have been thoroughly analyzed. At low flow velocities, severe particle settlement occurs, leading to increased collision frequency between particles and walls and significant charge accumulation. Increasing flow velocity can mitigate particle settlement and reduce charge levels. Changes in particle and pipe diameters have a minor impact on particle settlement but can increase single charge amounts with larger particle diameters and intensify particle charging with reduced pipe diameters due to shortened radial travel distances, leading to increased collision frequency. Our study meticulously illustrates the charge characteristics of individual particles and particle groups, providing a theoretical basis for assessing the electrostatic safety of liquid hydrogen transportation systems under extreme conditions.

Co-bioaugmentation with microalgae and probiotic bacteria: Sustainable solutions for upcycling of aquaculture wastewater and agricultural residues into microbial-rice bran complexes

Aquaculture farming generates a significant amount of wastewater, which has prompted the development of creative bioprocesses to improve wastewater treatment and bioresource recovery. One promising method of achieving these aims is to directly recycle pollutants into microbe-rice bran complexes, which is an economical and efficient technique for wastewater treatment that uses synergetic interactions between algae and bacteria. This study explores novel bioaugmentation as a promising strategy for efficiently forming microbial-rice bran complexes in unsterilized aquaculture wastewater enriched with agricultural residues (molasses and rice bran). Results found that rice bran serves a dual role, acting as both an alternative nutrient source and a biomass support for microalgae and bacteria. Co-bioaugmentation, involving the addition of probiotic bacteria (Bacillus syntrophic consortia) and microalgae consortiums (Tetradesmus dimorphus and Chlorella sp.) to an existing microbial community, led to a remarkable 5-fold increase in microbial-rice bran complex yields compared to the non-bioaugmentation approach. This method provided the most compact biofloc structure (0.50 g/L) and a large particle diameter (404 μm). Co-bioaugmentation significantly boosts the synthesis of extracellular polymeric substances, comprising proteins at 6.5 g/L and polysaccharides at 0.28 g/L. Chlorophyta, comprising 80% of the total algal phylum, and Proteobacteria, comprising 51% of the total bacterial phylum, are emerging as dominant species. These microorganisms play a crucial role in waste and wastewater treatment, as well as in the formation of microbial-rice bran complexes that could serve as an alternative aquaculture feed. This approach prompted changes in both microbial community structure and nutrient cycling processes, as well as water quality. These findings provide valuable insights into the transformative effects of bioaugmentation on the development of microbial-rice bran complexes, offering potential applications in bioprocesses for waste and wastewater management.

Synthesis and study of the properties of zirconium dioxide powders with different yttrium content

As part of the study, the influence of yttrium content on the properties of particles during controlled precipitation and after thermal treatment was investigated. Precipitation was carried out at a constant pH of 5 from nitric acid solutions, where the concentration of zirconium was 1 mole/dm3 and the yttrium content ranged from 0 to 30 % based on their oxides. The drying and calcination temperatures of the precipitates were 40 °C and 1000 °C, respectively. It was shown that with a yttrium content of up to 15 %, there was a consistent increase in the average diameter of zirconium hydroxide particles during deposition. When the yttrium concentration was increased to 30 %, the average particle size increased during the first 10 minutes of deposition, followed by a gradual decrease. The largest particle diameter was observed in the specimen with 7 % yttrium. In all cases, the formation of spherical aggregates was observed. With an increasing yttrium content, the boundaries between particles became smoother, and the degree of co-deposition of yttrium during synthesis decreased from 80 % to 60 %. Depending on the yttrium concentration, different modifications of stabilized zirconium dioxide powders were obtained: tetragonal ZrO2 for 2–7 % yttrium, and cubic ZrO2 for 15–30 % yttrium. Therefore, the results obtained during the study can be useful for the development of technology for the production of powdered materials for various applications.

Mobility of Zn and Cu in Bentonites: Implications for Environmental Remediation.

The aim of this study was to evaluate the mobility of copper (Cu) and zinc (Zn) and their impact on the properties of bentonites and unfrozen water content. Limited research in this area necessitates further analysis to prevent the negative effects of metal interactions on bentonite effectiveness. Tests involved American (SWy-3, Stx-1b) and Slovak (BSvk) bentonite samples with Zn or Cu ion exchange. Sequential extraction was performed using the Community Bureau of Reference (BCR) method. Elemental content was analyzed via inductively coupled plasma optical emission spectrometry (ICP-OES). Unfrozen water content was measured using nuclear magnetic resonance (1H-NMR) and differential scanning calorimetry (DSC). Results showed a significant influence of the main cation (Zn or Cu) on ion mobility, with toxic metal concentrations increasing mobility and decreasing residual fractions. Mobile Zn fractions increased with larger particle diameters, lower clay content, and shorter interplanar spacing, while the opposite was observed for Cu. Zn likely accumulated in larger clay pores, while Cu was immobilized in the bentonite complex. The stability of Zn or Cu ions increased with higher clay content or specific surface area. Residual Zn or Cu fractions were highest in uncontaminated bentonites with higher unfrozen water content, suggesting the potential formation of concentrated solutions in sub-zero temperatures, posing a threat to the clay-water environment, especially in cold regions.

SELECTION OF SUITABLE CATALYSTS FOR PRODUCTION OF NEW NANOCOMPOSITE MATERIALS

The article is devoted to the principles of hydrolytic polycondensation of tetramethoxysilane (TMOS) in an alkaline environment. Monolithic samples of SiO2 particles and xerogels were synthesized as a result of hydrolytic polycondensation of tetramethoxysilane in alkaline medium. Amine catalysts - pyridine derivatives were used to carry out the process. As a result, samples of different sizes were synthesized depending on the concentration of substances taken as catalysts. Smaller diameter particles were obtained at lower amine concentrations and larger diameter particles at higher concentrations. As the pKa value of the catalysts used in the synthesis of xerogels increases, certain increases and decreases in the properties of the resulting particles have been observed. Thus, with an increase in the pKa value, the density and hardness of the samples decreased, the percentage of SiO2 increased, and at the same time, the gelation time in the sol-gel system decreased. Images of the synthesized particles were obtained using a scanning electron microscope (SEM). Keywords: sol-gel, hydrolysis, polycondensation, tetramethoxysilane, xerogel, pKa, catalyst, SEM.

Effects of the geometric characteristics of graphene nanoplatelets on the physico-rheological properties of asphalt binder

While graphene nanoplatelets (GnPs) have emerged as promising nano-modifiers of asphalt binder in recent years, much is still unknown in terms of the existing correlations between the physical, chemical, and geometric characteristics of this nanofiller and observed asphalt binder properties. In this work, we investigate the important correlation between the geometric characteristics of GnPs and the rheological properties of the GnP-modified asphalt binder at high temperatures. Our results indicate that, in general, incorporating GnPs with large mean particle diameters (> 14 μm) and thicknesses (> 8 nm) enhances the high-temperature performance of the asphalt binder. The results of the multiple stress creep and recovery tests confirm that including GnPs in asphalt binder can decrease its permanent deformation by 33.2% and enhance its elastic recovery by 53.9%. Phase contrast images obtained by atomic force microscopy further indicate that the presence of GnPs with large mean particle diameters alters the morphology of the asphalt binder, leading to improved temperature stability and less susceptibility to permanent deformation.

Characterization of Polylactic Acid Biocomposites Filled with Native Starch Granules from Dioscorea remotiflora Tubers.

Biocomposites were fabricated utilizing polylactic acid (PLA) combined with native starch sourced from mountain's yam (Dioscorea remotiflora Knuth), an underexplored tuber variety. Different starch compositions (7.5, 15.0, 22.5, and 30.0 wt.%) were blended with PLA in a batch mixer at 160 °C to produce PLA/starch biocomposites. The biocomposites were characterized by analyzing their morphology, particle size distribution, thermal, X-ray diffraction (XDR), mechanical, and dynamic mechanical (DMA) properties, water absorption behavior, and color. The results showed that the amylose content of Dioscorea remotiflora starch was 48.43 ± 1.4%, which corresponds to a high-amylose starch (>30% of amylose). Particle size analysis showed large z-average particle diameters (Dz0) of the starch granules (30.59 ± 3.44 μm). Scanning electron microscopy (SEM) images showed oval-shaped granules evenly distributed throughout the structure of the biocomposite, without observable agglomeration or damage to its structure. XDR and DMA analyses revealed an increase in the crystallinity of the biocomposites as the proportion of the starch increased. The tensile modulus (E) underwent a reduction, whereas the flexural modulus (Eflex) increased with the amount of starch incorporated. The biocomposites with the highest Eflex were those with a starch content of 22.5 wt.%, which increased by 8.7% compared to the neat PLA. The water absorption of the biocomposites demonstrated a higher uptake capacity as the starch content increased. The rate of water absorption in the biocomposites followed the principles of Fick's Law. The novelty of this work lies in its offering an alternative for the use of high-amylose mountain's yam starch to produce low-cost bioplastics for different applications.

Investigation on submicron particle separation and deflection using tilted-angle standing surface acoustic wave microfluidics

With the development of in vitro diagnostics, extracting submicron scale particles from mixed body fluids samples is crucial. In recent years, microfluidic separation has attracted much attention due to its high efficiency, label-free, and inexpensive nature. Among the microfluidic-based separation, the separation based on ultrasonic standing waves has gradually become a powerful tool. A microfluid environment containing a tilted-angle ultrasonic standing surface acoustic wave (taSSAW) field has been widely adapted and designed to separate submicron particles for biochemical applications. This paper investigated submicron particle defection in microfluidics using taSSAWs analytically. Particles with 0.1–1 μm diameters were analyzed under acoustic pressure, flow rate, tilted angle, and SSAW frequency. According to different acoustic radiation forces acting on the particles, the motion of large-diameter particles was more likely to deflect to the direction of the nodal lines. Decreasing the input flow rate or increasing acoustic pressure and acoustic wave frequency can improve particle deflection. The tilted angle can be optimized by analyzing the simulation results. Based on the simulation analysis, we experimentally showed the separation of polystyrene microspheres (100 nm) from the mixed particles and exosomes (30–150 nm) from human plasma. This research results can provide a certain reference for the practical design of bioparticle separation utilizing acoustofluidic devices.

An original nondestructive sampling method to study the effect of gravity on the deposition of micron-sized large particles in exhaust gas recirculation (EGR) cooler fouling

Fouling is one of the barriers to developing more efficient and near-zero emission internal combustion engines. The micron-sized particulate matter is one of the roots of this fouling phenomenon in exhaust gas recirculation (EGR) coolers. This fouling is inadequately evaluated quantitatively, and its deposition mechanism is unknown. To investigate the effect of gravity on the deposition of micron-sized particles, an original nondestructive sampling fouling method and experiment apparatus have been developed to effectively obtain the upper and lower bottom fouling in the cooler in the direction of airflow, and the area proportion, count, and diameter of large particles in the fouling using image processing software. It was found that (i) the area proportion of large particles in the lower bottom fouling was almost 2.5 times higher than the upper bottom fouling; (ii) the count of large particles in the lower bottom fouling was higher, and the maximum diameter was larger, up to 639 μm; (iii) the mass of the lower bottom fouling was 1.5 times higher than the upper bottom fouling; (iv) gravity can significantly promote the deposition of micron-sized particles and should be considered in the design and arrangement of the EGR cooler to prevent fouling.

Flame spray drying of maltodextrin

In the frame of this work, the experimental analysis of the reconstitution properties, sorption isotherms and the Fourier-transform infrared spectroscopy (FTIR) spectra of maltodextrin powder was carried out. Before the analysis the substance was dried by standard spray drying method or flame spray drying (FSD). During the analyses, the influence of the applied FSD parameters on the analyzed properties was also estimated. The powders dried using the standard spray dryer were characterized by a better wettability parameter, which was related to a high bulk density. A shorter solubility time was obtained for powders dried by the FSD method, which may be explained by the larger particle diameters. Analyzing maltodextrin powders dried with the FSD, a significant influence of the atomization pressure and particle size on the wettability parameter was found. Application of FSD method does not affect the sorption characteristics of maltodextrin and does not change significantly the chemical structure of the material, since characteristic peaks of FTIR spectra were preserved after the FSD.

Computational Assessment of Unsteady Flow Effects on Magnetic Nanoparticle Targeting Efficiency in a Magnetic Stented Carotid Bifurcation Artery.

Worldwide, cardiovascular disease is the leading cause of hospitalization and death. Recently, the use of magnetizable nanoparticles for medical drug delivery has received much attention for potential treatment of both cancer and cardiovascular disease. However, proper understanding of the interacting magnetic field forces and the hydrodynamics of blood flow is needed for effective implementation. This paper presents the computational results of simulated implant assisted medical drug targeting (IA-MDT) via induced magnetism intended for administering patient specific doses of therapeutic agents to specific sites in the cardiovascular system. The drug delivery scheme presented in this paper functions via placement of a faintly magnetizable stent at a diseased location in the carotid artery, followed by delivery of magnetically susceptible drug carriers guided by the local magnetic field. Using this method, the magnetic stent can apply high localized magnetic field gradients within the diseased artery, while only exposing the neighboring tissues, arteries, and organs to a modest magnetic field. The localized field gradients also produce the forces needed to attract and hold drug-containing magnetic nanoparticles at the implant site for delivering therapeutic agents to treat in-stent restenosis. The multi-physics computational model used in this work is from our previous work and has been slightly modified for the case scenario presented in this paper. The computational model is used to analyze pulsatile blood flow, particle motion, and particle capture efficiency in a magnetic stented region using the magnetic properties of magnetite (Fe3O4) and equations describing the magnetic forces acting on particles produced by an external cylindrical electromagnetic coil. The electromagnetic coil produces a uniform magnetic field in the computational arterial flow model domain, while both the particles and the implanted stent are paramagnetic. A Eulerian-Lagrangian technique is adopted to resolve the hemodynamic flow and the motion of particles under the influence of a range of magnetic field strengths (Br = 2T, 4T, 6T, and 8T). Particle diameter sizes of 10nm-4µm in diameter were evaluated. Two dimensionless numbers were evaluated in this work to characterize relative effects of Brownian motion (BM), magnetic force induced particle motion, and convective blood flow on particle motion. The computational simulations demonstrate that the greatest particle capture efficiency results for particle diameters within the micron range of 0.7-4µm, specifically in regions where flow separation and vortices are at a minimum. Similar to our previous work (which did not involve the use of a magnetic stent), it was also observed that the capture efficiency of particles decreases substantially with particle diameter, especially in the superparamagnetic regime. Contrary to our previous work, using a magnetic stent tripled the capture efficiency of superparamagnetic particles. The highest capture efficiency observed for superparamagnetic particles was 78% with an 8T magnetic field strength and 65% with a 2T magnetic field strength when analyzing 100nm particles. For 10nm particles and an 8T magnetic field strength, the particle capture efficiency was 55% and for a 2T magnetic field strength the particle capture efficiency was observed to be 43%. Furthermore, it was found that larger magnetic field strengths, large particle diameter sizes (1µm and above), and slower blood flow velocity improves the particle capture efficiency. The distribution of captured particles on the vessel wall along the axial and azimuthal directions is also discussed. Results for captured particles on the vessel wall along the axial flow direction showed that the particle density decreased along the axial direction, especially after the stented region. For the entrance section of the stented region, the captured particle density distribution along the axial direction is large, corresponding to the center-symmetrical distribution of the magnetic force in that section. The simulation results presented in this work have shown to yield favorable capture efficiencies for micron range particles and superparamagnetic particles using magnetized implants such as the stent discussed in this work. The results presented in this work justify further investigation of MDT as a treatment technique for cardiovascular disease.

A Study on the Characteristics of Beach Profile Evolution According to the Particle Size Variation of Beach Nourishment

This study investigated the beach nourishment effect and topographical changes when using nourishment sand with relatively large particle diameters to perform beach nourishment on a beach subject to erosion. A physical model test was conducted in a 2D wave flume with an installed wind tunnel. The experiment examined the sediment transport mechanism under conditions with wind and waves. Although applying nourishment sand with large particle diameters attenuated sediment transport, the increase in particle diameter was not always proportional to the reduction in topographical changes. Increasing the particle diameter of the nourishment sand increased the friction force between particles, resulting in large-scale erosion and accretion around the coastline, and this trend increased with winds. Also, with wind, the wave run-up height increased, the undertow became stronger, and large-scale scouring occurred at the boundary between the nourishment sand and the existing beach. Increasing the particle diameter of the nourishment sand played a role in reducing the run-up phenomenon (d50: 1.0 mm with 24–50%, d50: 5.0 mm with 59–83%), and the range of particles moved by winds also decreased (d50: 1.0 mm with 10–38%, d50: 5.0 mm with 5–37%).

Four-way coupled Eulerian-Lagrangian study of phase interaction mechanism in the supersonic gas-solid two-phase flow

Supersonic gas–solid jet injection has received much attention in many industrial applications such as pneumatic conveying, powdered drug delivery, steel refining process and thermal spray coating, but it is still a challenging topic due to the complex interphase interaction in compressible flows. In this work, supersonic gas–solid two-phase flow is numerically studied under the Eulerian-Lagrangian framework. After the model validation with the experimental measurement, the inherent mechanism of supersonic gas–solid flow under the conditions of different powder feeding rates and particle diameters is explored. The results demonstrate that increasing the powder feeding rate leads to the reduction of the axial velocity and penetration ability of the particles. Especially when powder feeding rate increases to 10 kg/s, serious blockage occurs in the nozzle divergence section and the conventional supersonic flow characteristic in Laval nozzle has been substantially changed. Moreover, particle diameter largely determines the dynamic and thermodynamic characteristics of the particles. Small-diameter particles exhibit better followability to the gas phase and large-diameter particles exert non-negligible impact on the gas flow, mainly reflects in weakening the expansion ability of the gas phase. The results obtained in this work provide meaningful insight for understanding the flow characteristics of supersonic gas–solid flow and benefit the operating parameters selection in industrial applications.

Numerical study on coupled flow characteristics of a gas-solid two-phase jet in a supersonic crossflow

In this study, the Eulerian-Lagrangian scheme coupled with the gas-solid two-phase Reynolds-average Navier-Stokes (RANS) method was used to study the airflow and particles flow characteristics of particles of different diameters injected into a supersonic flow field by a sonic jet. The results show that introducing small particles has little effect on the flow field. When the particle diameter is 1e-6 m, most particles are mainly distributed in the shear layer, and some parts of the particles are sucked into the surface trailing counter-rotating vortex pairs (TCVP) and the wall boundary layers by the airflow. The introduction of large diameter particles hinders the jet's development, reduces the Mach disk's height, and makes the counter-rotating vortex pair (CVP) closer to the wall. This leads to a decrease in the streamwise velocity and an increase in the wall-normal velocity near the wall downstream of the jet. The streamwise velocity increases and the wall-normal velocity decreases at the far wall downstream of the jet. At the same time, it exacerbates the Kelvin-Helmholtz (K-H) instability in the shear layer on the windward side of the jet, forming a large-scale coherent structure between the shear layer and crossflow. The penetration depth and diffusion range of particles increase with particle diameter and density, and the velocity decreases with particle diameter increase by comparing the trajectories of particles with different diameters and densities.

Numerical simulation and experimental study of two-phase flow in downhole spiral gas-liquid separator

Gas-liquid separator is an important surface equipment in oilfield development. Improving the separation efficiency of separator is of great significance to the overall economic benefit of oilfield. Spiral separator is a high efficiency separation device that has been widely used, but at present, there are not enough studies on separation efficiency in number of spiral turns and pitches. In view of this problem, this paper analyzed the gas–liquid separation efficiency of spiral separators with different number of spiral turns and pitches via the fluent numerical simulation software and laboratory experiments. The results showed that a greater number of spiral turns and a larger particle diameter could lead to higher separation efficiency. The separation efficiency has an optimum value for the pitch. The performance of the downhole spiral separator was verified by laboratory experiments, and the separation efficiency was above 90% under the conditions where the treatment amount was either unchanged or changed. These results can provide a reference for the application of spiral separators in oil fields.

Dip coating of viscous granular suspensions

A solid substrate withdrawn from a liquid bath is coated with a uniform thickness given by the Landau–Levich–Derjaguin (LLD) law. If the bath is a suspension of neutrally buoyant particles, the liquid coating can entrain particles in a process known as capillary filtration that only depends on the capillary number Ca. Experiments were performed using a custom-built dip coating apparatus and gravimetry techniques. The working liquids were monodisperse and bidisperse suspensions with larger particle diameters and higher liquid viscosity than previously reported. The single particle entrainment point for monodisperse suspensions agrees well with the critical capillary number predicted in prior literature. Bidisperse suspensions exhibit active filtration regions where only the smallest particles are entrained with the range of Ca for active filtration consistent with reported models. These experimental results both validate and enhance our understanding of capillary filtration by exploring larger particle-sized granular suspensions of higher viscosity solutions, as relevant to applications in construction, medical care, personal care products, and food science.