Large Segmental Bone Defects Research Articles

3D-Printed Bifunctional Scaffold for Treatment of Critical Bone Defects Based on Osteoimmune Microenvironment Regulation and Osteogenetic Effects.

The critical-sized bone defect resulting from trauma, tumor resection, and congenital deformity fails to undergo spontaneous healing due to its substantial size, while the ensuing inflammatory process and hypoxic environment further impede the regenerative process. Therefore, it has consistently presented a significant clinical challenge. In the present study, we incorporate a glycyrrhizic acid (GA)-functionalized hydrogel onto the surface of a Hydroxyapatite (Hap)-modified Polycaprolactone (PCL) scaffold to fabricate a composite scaffold. The composed scaffold showed favorable anti-inflammatory and antioxidative capabilities by modulating macrophage polarization and scavenging reactive oxygen species (ROS); the modification of Hap enhanced its osteogenic ability. An in vivo rat skull defect model confirmed that the composed scaffold efficiently promotes bone regeneration. In general, the composed scaffold with the ability of osteoimmune microenvironment regulation can effectively repair critical-sized bone defects. This strategy provides a promising method for the reconstruction of large segmental bone defects.

Incorporating Hydrogel (with Low Polymeric Content) into 3D-Printed PLGA Scaffolds for Local and Sustained Release of BMP2 in Repairing Large Segmental Bone Defects.

Treating large bone defects remains a considerable challenge for clinicians: bone repair requires scaffolds with mechanical properties and bioactivities. Herein, based on crosslinking o-phthalaldehyde (OPA) with amine groups, 4-arm polyethylene glycol (4armPEG)-OPA/Gelatin hydrogel loaded with bone morphogenetic protein 2 (BMP2) is prepared and a three dimensional (3D)-printed poly (lactic-co-glycolic acid) (PLGA) porous scaffold is filled with the hydrogel solution. The composite scaffold, with a compression modulus of 0.68 ±0.097GPa similar to the cancellous bone, has a porosity of 56.67 ± 4.72% and a pore size of about 380µm, promoting bone growth. The hydrogel forms a porous network at low concentrations, aiding protein release and cell migration. The hydrogel degrades in approximately three weeks, and the scaffold takes five months, matching bone repair timelines. BMP2 release experiment shows a sustained BMP2 release with a 72.4 ± 0.53% release ratio. The ALP activity test and alizarin red staining shows effective osteogenic promotion, while RT-PCR confirms BMP2@Gel enhanced COL-1 and OPN expression. Animal experiments further validate the composite scaffold's bone repair efficacy. This study demonstrates the effectiveness of the hydrogel in releasing BMP2 and the mechanical support of the 3D-printed PLGA porous scaffold, providing a new treatment for bone defects.

Electrophoretic deposition of curcumin-loaded mesoporous bioactive glass nanoparticle-chitosan composite coatings on titanium for treating tumor-induced bone defect

Clinical treatment of osteosarcoma (OS) presents significant challenges in postoperative tumor recurrence and large segmental bone defects, often necessitating joint replacement or artificial bone implantation to repair failed or defective bone tissue. At the same time, fibroblastic encapsulation can impede direct contact between implants and bones, leading to implant failure. To tackle these issues, mesoporous bioactive glass nanoparticles (MBN) were synthesized and then loaded with curcumin (CUR). Subsequently, chitosan (CTS) was chosen as the charger and coating matrix, and electrophoretic deposition (EPD) was utilized to fabricate a CTS-MBN-CUR composite coating with triple functionality on Ti implants aiming for OS-induced bone repair. MBN-CUR nanoparticles are encapsulated in CTS and uniformly distributed within the coating, achieving robust adhesion and long-term release of CUR. Concurrently, the developed CTS-MBN-CUR coating exhibits moderate hydrophilicity, and good bioactivity. Moreover, three different types of cells, MC3T3-E1, L929, and MG63 cells, were individually cultured with the composite coating and subjected to comprehensive cellular studies. The coating presented favorable bioactivities, and osteogenic performance, and the ability to resist the activity of fibroblast and OS cells. These findings suggest that CTS-MBN-CUR holds promising potential for bone regeneration following OS resection surgery.

Research progress in repair and reconstruction of tumor-related bone defects in proximal femur

To review the repair and reconstruction methods for large segmental femoral proximal bone defects caused by tumors, and to explore their clinical application effects, advantages, and disadvantages, and future research directions. A comprehensive search of Chinese and foreign databases was conducted to select basic and clinical research literature related to the repair and reconstruction of femoral proximal bone defects caused by tumors. The studies were classified and analyzed based on two main strategies: hip-preserving reconstruction and non-hip-preserving reconstruction. In hip-preserving reconstruction, traditional methods such as allograft transplantation and vascularized autograft transplantation are common but have risks of poor bone integration and bone resorption. The clinical application of inactivated tumor segment reimplantation and distraction osteogenesis techniques is limited. In recent years, three-dimensional printing technology has become increasingly mature, with personalized prostheses and precise surgeries becoming development trends. Non-hip-preserving reconstruction primarily includes allograft prosthesis composite and total femoral replacement. The former focuses on improving the survival rate and bone integration efficiency of the allograft, while the latter requires the simultaneous reconstruction of hip and knee joint stability. Significant progress has been made in repairing and reconstructing proximal femoral bone defects caused by tumors, but many challenges remain. The integration of three-dimensional printing technology and digital design offers potential for precise bone defect repair. Future efforts should focus on new concepts, technologies, and materials through multidisciplinary approaches to provide personalized and precise solutions, thereby improving patient quality of life.

Smart Implantable Hydrogel for Large Segmental Bone Regeneration.

Large segmental bone defects often lead to nonunion and dysfunction, posing a significant challenge for clinicians. Inspired by the intrinsic bone defect repair logic of "vascularization and then osteogenesis", this study originally reports a smart implantable hydrogel (PDS-DC) with high mechanical properties, controllable scaffold degradation, and timing drug release that can proactively match different bone healing cycles to efficiently promote bone regeneration. The main scaffold of PDS-DC consists of polyacrylamide, polydopamine, and silk fibroin, which endows it with superior interfacial adhesion, structural toughness, and mechanical stiffness. In particular, the adjustment of scaffold cross-linking agent mixing ratio can effectively regulate the in vivo degradation rate of PDS-DC and intelligently satisfy the requirements of different bone defect healing cycles. Ultimately, PDS hydrogel loaded with free desferrioxamine (DFO) and CaCO3 mineralized ZIF-90 loaded bone morphogenetic protein-2 (BMP-2) to stimulate efficient angiogenesis and osteogenesis. Notably, DFO is released rapidly by free diffusion, whereas BMP-2 is released slowly by pH-dependent layer-by-layer disintegration, resulting in a significant difference in release time, thus matching the intrinsic logic of bone defect repair. In vivo and in vitro results confirm that PDS-DC can effectively realize high-quality bone generation and intelligently regulate to adapt to different demands of bone defects.

Research progress of gene therapy combined with tissue engineering to promote bone regeneration

Gene therapy has emerged as a highly promising strategy for the clinical treatment of large segmental bone defects and non-union fractures, which is a common clinical need. Meanwhile, many preclinical data have demonstrated that gene and cell therapies combined with optimal scaffold biomaterials could be used to solve these tough issues. Bone tissue engineering, an interdisciplinary field combining cells, biomaterials, and molecules with stimulatory capability, provides promising alternatives to enhance bone regeneration. To deliver and localize growth factors and associated intracellular signaling components into the defect site, gene therapy strategies combined with bioengineering could achieve a uniform distribution and sustained release to ensure mesenchymal stem cell osteogenesis. In this review, we will describe the process and cell molecular changes during normal fracture healing, followed by the advantages and disadvantages of various gene therapy vectors combined with bone tissue engineering. The growth factors and other bioactive peptides in bone regeneration will be particularly discussed. Finally, gene-activated biomaterials for bone regeneration will be illustrated through a description of characteristics and synthetic methods.

Gradual Transverse Transport of Naturally Tibialized Fibula Using Hexapod Frames to Treat Neglected Type V Tibial Segmental Defects.

Although several reconstructive methods have been developed to manage large segmental tibial bone defects including bone transport (distraction osteogenesis), contralateral fibular graft, allograft, tibiofibular synostosis, Masquelet technique, and 3D printed scaffold, neglected large tibial defects in adults remain challenging problems. This study describes gradual transverse transport of naturally tibialized fibula using hexapod frames in management of adult patients with neglected large tibial defects. We retrospectively reviewed four cases of transverse transport of naturally tibialized fibula from November 2018 to February 2022. We measured the length of the tibial defect and the transported fibular segment, the mid-diaphyseal diameter and cortical thickness of the affected fibula, contralateral fibula, and tibia. The parameters measured both preoperatively and postoperatively were leg length discrepancy, hip-knee-ankle angle, medial proximal tibial angle, posterior proximal tibial angle, lateral distal tibial angle, range of motion of the knee and ankle joints, and Lower Extremity Functional Scores (LEFS). Patients' satisfaction rates using Likert scale were also recorded. Among four female patients, three suffered from tibial osteomyelitis, and one was due to congenital pseudarthrosis of the tibia. The average follow-up time was 2.7 ± 1.4 years. The average length of tibial defect was 14.0 ± 0.8 cm. The average preoperative shortening of the affected leg was 9.0 ± 2.5 cm, which changed to 0.6 ± 0.8 cm postoperatively. The median length of the transported fibular segment was 15.2 cm. Two patients had varus deformity, two had recurvatum, and one had procurvatum preoperatively. Postoperative radiological measurement showed all deformities corrected and no ankle valgus deformity developed during follow-up. All patients achieved union and can fully weight bear on the affected extremity. The average fixator time was 12.9 ± 2.9 months. The average preoperative and postoperative LEFS, respectively, were 53.5 ± 5.0, 70.5 ± 1.3, with a significant difference (p = 0.003). Three patients reported very satisfied with the outcome, and one patient reported satisfied. Three patients had pin tract infections, and one patient had skin necrosis which healed after additional surgery. One patient had surgical release of the hamstring tendons due to flexion contracture of the knee. Two patients had 15° of reduction in ankle range of motion. One patient had transient common peroneal nerve palsy which spontaneously recovered within 6 weeks. The transverse transport of naturally tibialized fibula was both a safe and effective method to treat the long-standing type V tibial segmental defect.

Bone Transport for Large Segmental Tibial Defects Using Taylor Spatial Frame versus the Ilizarov Circular Fixator.

Bone transport has become the gold standard for treating large segmental tibial bone defects. The technique for application the Ilizarov circular fixator (ICF) has a long learning curve and is associated with many complications. There are few clinical studies on bone transport via the Taylor spatial frame (TSF). The main purpose of this study was to compare the radiological and clinical and outcomes of bone transport by using the TSF and the ICF. There were 62 patients included in this retrospective study from June 2011 to June 2021 and distributed to two groups according to the fixation method: a TSF group consisting of 30 patients and an ICF group consisting of 32 patients. Demographic information, surgical duration, external fixation times, external fixation index, final radiographic results, complications, and clinical outcomes were recorded and examined. The clinical outcomes were assessed using the ASAMI criteria during the most recent clinical visit. Then, statistical analysis such as independent-samples t tests or chi-Square test was performed. The mean surgical duration in the TSF group was 93.8 ± 7.3 min, which was shorter than that in the ICF group (109.8 ± 1.4 min) (p < 0.05). Compared to the ICF group (10.2 ± 2.0 months), the TSF group (9.7 ± 1.8 months) had a shorter average external fixation time (p > 0.05). The external fixation index was 1.4 ± 0.2 m/cm and 1.5 ± 0.1 m/cm in the two groups. Moreover, there was no significant difference between the two groups. At the last follow-up visit, the medial proximal tibial angle (MPTA) and posterior proximal tibial angle (PPTA) in the TSF group were 88.1 ± 12.1° and 80.9 ± 1.3°, respectively. The MPTA and PPTA in the ICF group were 84.4 ± 2.4° and 76.2 ± 1.9°, respectively. There were statistically significant differences between the two groups (all p < 0.05). The complication rate was 50% in the TSF group and 75% in the ICF group. Moreover, the ASAMI score between the two groups was no statistically significant difference (p > 0.05). No statistically significant difference was found in clinical outcomes between the use of Taylor spatial frame and Ilizarov circular fixator for treating large segmental tibial bone defects. However, TSF is a shorter and simpler procedure that causes fewer complications and improves limb alignment.

The Masquelet induced membrane technique with PRP-FG-nHA/PA66 scaffold can heal a rat large femoral bone defect

BackgroundMasquelet membrane induction technology is one of the treatment strategies for large bone defect (LBD). However, the angiogenesis ability of induced membrane decreases with time and autologous bone grafting is associated with donor site morbidity. This study investigates if the PRP-FG-nHA/PA66 scaffold can be used as a spacer instead of PMMA to improve the angiogenesis ability of induced membrane and reduce the amount of autologous bone graft.MethodsPlatelet rich plasma (PRP) was prepared and PRP-FG-nHA/PA66 scaffold was synthesized and observed. The sustained release of VEGFA and porosity of the scaffold were analyzed. We established a femur LBD model in male SD rats. 55 rats were randomly divided into four groups depending on the spacer filled in the defect area. “Defect only” group (n = 10), “PMMA” group (n = 15), “PRP-nHA/PA66” group (n = 15) and “PRP-FG-nHA/PA66” group (n = 15 ). At 6 weeks, the spacers were removed and the defects were grafted. The induced membrane and bone were collected and stained. The bone formation was detected by micro-CT and the callus union was scored on a three point system.ResultsThe PRP-FG-nHA/PA66 scaffold was porosity and could maintain a high concentration of VEGFA after 30 days of preparation. The induced membrane in PRP-FG-nHA/PA66 group was thinner than PMMA, but the vessel density was higher.The weight of autogenous bone grafted in PRP-FG-nHA/PA66 group was significantly smaller than that of PMMA group. In PRP-FG-nHA/PA66 group, the bone defect was morphologically repaired.ConclusionThe study showed that PRP-FG-nHA/PA66 scaffold can significantly reduce the amount of autologous bone graft, and can achieve similar bone defect repair effect as PMMA. Our findings provide some reference and theoretical support for the treatment of large segmental bone defects in humans.

Gradient gyroid Ti6Al4V scaffolds with TiO2 surface modification: Promising approach for large bone defect repair

Large bone defects, particularly those exceeding the critical size, present a clinical challenge due to the limited regenerative capacity of bone tissue. Traditional treatments like autografts and allografts are constrained by donor availability, immune rejection, and mechanical performance. This study aimed to develop an effective solution by designing gradient gyroid scaffolds with titania (TiO2) surface modification for the repair of large segmental bone defects. The scaffolds were engineered to balance mechanical strength with the necessary internal space to promote new bone formation and nutrient exchange. A gradient design of the scaffold was optimized through Finite Element Analysis (FEA) and Computational Fluid Dynamics (CFD) simulations to enhance fluid flow and cell adhesion. In vivo studies in rabbits demonstrated that the G@TiO2 scaffold, featuring a gradient structure and TiO2 surface modification, exhibited superior healing capabilities compared to the homogeneous structure and TiO2 surface modification (H@TiO2) and gradient structure (G) scaffolds. At 12 weeks post-operation, in a bone defect representing nearly 30 % of the total length of the radius, the implantation of the G@TiO2 scaffold achieved a 27 % bone volume to tissue volume (BV/TV) ratio, demonstrating excellent osseointegration. The TiO2 surface modification provided photothermal antibacterial effects, enhancing the scaffold's biocompatibility and potential for infection prevention. These findings suggest that the gradient gyroid scaffold with TiO2 surface modification is a promising candidate for treating large segmental bone defects, offering a combination of mechanical strength, bioactivity, and infection resistance.

The effects of 3D printing parameters, structural design and post-processing on the mechanical properties and corrosion resistance of SLMed ZK60 porous scaffolds

High-quality porous Mg alloy scaffolds show promise in repairing large segmental bone defects. In this study, the authors prepared porous ZK60 scaffolds using the selective laser melting (SLM) method with three different model structures: Gyroid (G), Diamond (D), and Dodecahedral (Do). The researchers investigated the structural refinement, mechanical properties, and corrosive properties of SLM-ed ZK60 by adjusting the 3D printing parameters, specifically the scanning speed and laser power. The results show that, with optimized process parameters of a scanning speed of 400 mm/s and a laser power of 110 W, the relative density of the prepared samples was higher than 97 %. After post-processing with electrolytic polishing, the G model scaffolds showed a smooth structural transition and the largest surface area compared to the other two models. The electrolytic polishing treatment also improved the structural refinement of the 70 % designed porosity, with an error of only 4.3 %. Additionally, the Do model scaffolds exhibited the best mechanical properties, with a yield strength of up to 24 MPa and an elastic modulus of up to 425 MPa. Furthermore, after coating treatment, the corrosion rate decreased from 5.67 mm/year to 1.34 mm/year after 48 h. These results demonstrate the potential of SLM-ed porous scaffolds for biomedical applications.

Reconstruction of Segmental Bone Defect in Canine Tibia Model Utilizing Bi-Phasic Scaffold: Pilot Study.

The reunion and restoration of large segmental bone defects pose significant clinical challenges. Conventional strategies primarily involve the combination of bone scaffolds with seeded cells and/or growth factors to regulate osteogenesis and angiogenesis. However, these therapies face inherent issues related to immunogenicity, tumorigenesis, bioactivity, and off-the-shelf transplantation. The biogenic micro-environment created by implanted bone grafts plays a crucial role in initiating the bone regeneration cascade. To address this, a highly porous bi-phasic ceramic synthetic bone graft, composed of hydroxyapatite (HA) and alumina (Al), was developed. This graft was employed to repair critical segmental defects, involving the creation of a 2 cm segmental defect in a canine tibia. The assessment of bone regeneration within the synthetic bone graft post-healing was conducted using scintigraphy, micro-CT, histology, and dynamic histomorphometry. The technique yielded pore sizes in the range of 230-430 μm as primary pores, 40-70 μm as secondary inner microchannels, and 200-400 nm as tertiary submicron surface holes. These three components are designed to mimic trabecular bone networks and to provide body fluid adsorption, diffusion, a nutritional supply, communication around the cells, and cell anchorage. The overall porosity was measured at 82.61 ± 1.28%. Both micro-CT imaging and histological analysis provided substantial evidence of robust bone formation and the successful reunion of the critical defect. Furthermore, an histology revealed the presence of vascularization within the newly formed bone area, clearly demonstrating trabecular and cortical bone formation at the 8-week mark post-implantation.

Application of double plate fixation combined with Masquelet technique for large segmental bone defects of distal tibia: a retrospective study and literature review.

There is no effective consensus on the choice of internal fixation method for the Masquelet technique in the treatment of large segmental bone defects of the distal tibia. Thus, the study aimed to investigate the outcomes of the Masquelet technique combined with double plate fixation in the treatment of large segmental bone defects. This was a retrospective study involving 21 patients with large segmental bone defects of the distal tibia who were treated between June 2017 and June 2020. The length of bone defect ranged from 6.0cm to 11cm (mean, 8.19cm). In the first stage of treatment, following complete debridement, a cement spacer was placed to induce membrane formation. In the second stage, double plate fixation and autologous cancellous bone grafting were employed for bone reconstruction. Each patient's full weight-bearing time, bone healing time, and Iowa ankle score were recorded, and the occurrence of any complications was noted. All patients were followed up for 16 to 26months (mean, 19.48months). The group mean full weight-bearing time and bone healing time after bone grafting were 2.41 (± 0.37) months and 6.29 (± 0.66) months, respectively. During the treatment, one patient had a wound infection on the medial side of the leg, so the medial plate was removed. The wound completely healed after debridement without any recurrence. After extraction of iliac bone for grafting, one patient had a severe iliac bone defect, which was managed by filling the gap with a cement spacer. Most patients reported mild pain in the left bone extraction area after surgery. The postoperative Iowa ankle score range was 84-94 (P < 0.05). In this cohort, 15 cases were rated as "excellent", and 6 cases as "good" on the Iowa ankle scoring system. The Masquelet technique combined with double plate fixation is a safe and effective method for the treatment of large segmental bone defects of the distal tibia.

Synergistic large segmental bone repair by 3D printed bionic scaffolds and engineered ADSC nanovesicles: Towards an optimized regenerative microenvironment

Achieving sufficient bone regeneration in large segmental defects is challenging, with the structure of bone repair scaffolds and their loaded bioactive substances crucial for modulating the local osteogenic microenvironment. This study utilized digital laser processing (DLP)-based 3D printing technology to successfully fabricate high-precision methacryloylated polycaprolactone (PCLMA) bionic bone scaffold structures. Adipose-derived stem cell-engineered nanovesicles (ADSC-ENs) were uniformly and stably modified onto the bionic scaffold surface using a perfusion device, constructing a conducive microenvironment for tissue regeneration and long bone defect repair through the scaffold's structural design and the vesicles' biological functions. Scanning electron microscopy (SEM) examination of the scaffold surface confirmed the efficient loading of ADSC-ENs. The material group loaded with vesicles (PCLMA-BAS-ENs) demonstrated good cell compatibility and osteogenic potential when analyzed for the adhesion and osteogenesis of primary rabbit bone marrow mesenchymal stem cells (BMSCs) on the material surface. Tested in a 15 mm critical rabbit radial defect model, the PCLMA-BAS-ENs scaffold facilitated near-complete bone defect repair after 12 weeks. Immunofluorescence and proteomic results indicated that the PCLMA-BAS-ENs scaffold significantly improved the osteogenic microenvironment at the defect site in vivo, promoted angiogenesis, and enhanced the polarization of macrophages towards M2 phenotype, and facilitated the recruitment of BMSCs. Thus, the PCLMA-BAS-ENs scaffold was proven to significantly promote the repair of large segmental bone defects. Overall, this strategy of combining engineered vesicles with highly biomimetic scaffolds to promote large-segment bone tissue regeneration holds great potential in orthopedic and other regenerative medicine applications.

Indications for Nonbiological Reconstruction of Posttraumatic Bone Defects About the Knee.

3D printing and modeling has continued to grow in popularity over the past decade because the technology has matured and become more affordable and widely available. The main indications for nonbiological reconstruction of large bone defects are principally those patients where the candidate is unlikely to be successful if reconstructed by other means. Bespoke, custom, patient-specific implants can be designed to very effectively address bone loss, incorporating design elements that are particular to the needs of any given unique clinical condition. These implants are generally designed as titanium scaffolds that encourage bony incorporation at the host implant junction both proximal and distal. These scaffolds are typically considered a cellular solid, with high porosity that also promotes bone ingrowth directly into the substance of the body of the implant. Titanium scaffolds of this type have become a useful treatment alternative for large segmental bone defects around the knee, especially distal femoral defects. These are often adult patients with local or systemic compromise, or instead they may be too young to be considered candidates for reconstruction using a megaprosthesis. The process requires careful evaluation of individual patients, then matching that patient with the best treatment option, while recognizing the expectations and demands specific to that particular patient. Several cases are presented here to illustrate the variety of indications that can be successfully addressed with this technology, highlighting the quality of the clinical outcome that can be achieved despite the complexity of the pathology encountered.

Which surgical technique may yield the best results in large, infected, segmental non-unions of the tibial shaft? A scoping review

PurposeInfected nonunion of the tibia with a large segmental bone defect is a complex and challenging condition for the patient and surgeon. This scoping review was conducted to identify existing evidence and knowledge gaps regarding this clinical scenario. Secondly, the objective of this study was to search for a valid recommendation on the optimal treatment.MethodsA comprehensive search was conducted in the bibliographic databases: PubMed, Embase.com, and Web of Science Core Collection. Studies reporting on bone transport techniques, the Masquelet technique, and vascularized fibular grafts in bone defects greater than 5 cm were included. Bone healing results and functional results were compared according to duration of nonunion, infection recurrence, bone consolidation, complication rate, external fixation time, and time until full weight-bearing.ResultsOf the 2753 articles retrieved, 37 studies could be included on bone transport techniques (n = 23), the Masquelet technique (n = 7), and vascularized fibular grafts (n = 7). Respective bone union percentages were 94.3%, 89.5%, and 96.5%. The percentages of infection recurrence respectively were 1.6%, 14.4% and 7.0%, followed by respectively 1.58, 0.78, and 0.73 complications per patient.ConclusionBone transport was found to be the most widely studied technique in the literature. Depending on the surgeon’s expertise, vascularized fibular grafts may be held as a favourable alternative. This review indicates that further high-quality research on large bone defects (≥\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\ge$$\\end{document} 5 cm) in patients with infected tibial nonunions is necessary to gain more insight into the potentially beneficial results of vascularized fibular grafts and the Masquelet technique.

Bone transport combined with sequential nailing technique for the management of large segmental bone defects after trauma.

Bone transport technique is widely used for the management of large segmental bone defects. However, several reasons may prevent its successful completion, such as poor osteogenesis, docking site nonunion, severe chronic pain and psychological problems. We used sequential nailing technique to solve these problems. The objective of this study was to analyze the clinical effects of our modified technique for the management of large segmental bone defects after trauma. Twenty-three patients using bone transport combined with sequential nailing technique in our institution from June 2011 to June 2020 were included and analyzed retrospectively. There were 15 males and eight females. The age ranged from 19 to 64 years. There were eight cases suffering from basic medical diseases. The initial injury was open in 14 patients. Seven cases encountered femoral defects and 16 for tibia. The main reasons for sequential nailing technique were docking site nonunion (nine cases), poor osteogenesis (five cases), severe chronic pain (five cases) and psychological problems (four cases). The residual bone defects after removing the external fixator, operation plans, complications and follow-up time were recorded. Bone defect healing was evaluated by Paley score. The mean residual bone defects were (2.9 ± 1.9) cm. The mean time in external fixator was (9.5 ± 3.4) months. The average follow-up time was (23 ± 3) months. With respect to complications, two cases suffered from nonunion again and were treated by bone graft with augmented plate fixation. No infection recurrence was found in these cases. The excellent and good rate of bone defect healing was 91.3%. Bone transport combined with sequential nailing technique could shorten the external fixation time, overcome the inconvenience of the external frame to patients, eliminate chronic pain and be easy for patients to accept. Patients using this modified technique achieved high satisfaction.

Dual-functional 3D-printed porous bioactive scaffold enhanced bone repair by promoting osteogenesis and angiogenesis

The treatment of bone defects is a difficult problem in orthopedics. The excessive destruction of local bone tissue at defect sites destroys blood supply and renders bone regeneration insufficient, which further leads to delayed union or even nonunion. To solve this problem, in this study, we incorporated icariin into alginate/mineralized collagen (AMC) hydrogel and then placed the drug-loaded hydrogel into the pores of a 3D-printed porous titanium alloy (AMCI/PTi) scaffold to prepare a bioactive scaffold with the dual functions of promoting angiogenesis and bone regeneration. The experimental results showed that the ACMI/PTi scaffold had suitable mechanical properties, sustained drug release function, and excellent biocompatibility. The released icariin and mineralized collagen (MC) synergistically promoted angiogenesis and osteogenic differentiation in vitro. After implantation into a rabbit radius defect, the composite scaffold showed a satisfactory effect in promoting bone repair. Therefore, this composite dual-functional scaffold could meet the requirements of bone defect treatment and provide a promising strategy for the repair of large segmental bone defects in clinic.

NR4A1 PROMOTES OSTEOGENIC DIFFERENTIATION OF MESENCHYMAL STEM CELLS AND IMPROVES INFLAMMATION-INHIBITED BONE REGENERATION

Stem cell therapy is an effective means to address the repair of large segmental bone defects. However, the intense inflammatory response triggered by the implants severely impairs stem cell differentiation and tissue regeneration. High-dose transforming growth factor β1 (TGF-β1), the most locally expressed cytokine in implants, inhibits osteogenic differentiation of bone marrow mesenchymal stem cells (BMSCs) and promotes tissue fibrosis, severely compromising the efficacy of stem cell therapy. Small molecule inhibitors of TGF-β1 can be used to ameliorate the osteogenic disorders caused by high concentrations of TGF-β1, but systemic inhibition of TGF-β1 function will cause strong adverse effects. How to find safe and reliable molecular targets to antagonize TGF-β1 remains to be elucidated. Orphan nuclear receptor Nr4a1, an endogenous inhibitory molecule of TGF-β1, suppresses tissue fibrosis, but its role in BMSC osteogenesis is unclear. We found that TGF-β1 inhibited Nr4a1 expression through HDAC4. Overexpression of Nr4a1 in BMSCs reversed osteogenic differentiation inhibited by high levels of TGF- β1. Mechanistically, RNA sequencing showed that Nr4a1 activated the ECM-receptor interaction and Hippo signaling pathway, which in turn promoted BMSC osteogenesis. In bone defect repair and fracture healing models, transplantation of Nr4a1-overexpressing BMSCs into C57BL/6J mice or treatment with the Nr4a1 agonist Csn-B significantly ameliorated inflammation-induced bone regeneration disorders. In summary, our findings confirm the endogenous inhibitory effect of Nr4a1 on TGF- β1 and uncover the effectiveness of Nr4a1 agonists as a therapeutic tool to improve bone regeneration, which provides a new solution strategy for the treatment of clinical bone defects and inflammatory skeletal diseases.

Absorbable calcium and phosphorus bioactive membranes promote bone marrow mesenchymal stem cells osteogenic differentiation for bone regeneration.

Large segmental bone defects are commonly operated with autologous bone grafting, which has limited bone sources and poses additional surgical risks. In this study, we fabricated poly(lactide-co-glycolic acid) (PLGA)/β-tricalcium phosphate (β-TCP) composite membranes by electrostatic spinning and further promoted osteogenesis by regulating the release of β-TCP in the hope of replacing autologous bone grafts in the clinical practice. The addition of β-TCP improved the mechanical strength of PLGA by 2.55 times. Moreover, β-TCP could accelerate the degradation of PLGA and neutralize the negative effects of acidification of the microenvironment caused by PLGA degradation. In vitro experiments revealed that PLGA/TCP10 membranes are biocompatible and the released β-TCP can modulate the activity of osteoblasts by enhancing the calcium ions concentration in the damaged area and regulating the pH of the local microenvironment. Simultaneously, an increase in β-TCP can moderate the lactate content of the local microenvironment, synergistically enhancing osteogenesis by promoting the tube-forming effect of human umbilical vein endothelial cells. Therefore, it is potential to utilize PLGA/TCP bioactive membranes to modulate the microenvironment at the site of bone defects to promote bone regeneration.