Large-scale Hydrogen Production Research Articles

Dynamic hydrogen bubble template electrodeposition of a self-supported Co-P electrocatalyst for efficient alkaline oxygen evolution reaction

The development of efficient, inexpensive, and earth-abundant electrocatalysts for the oxygen evolution reaction (OER) represents a significant challenge for the large-scale production of hydrogen. The primary obstacle to the advancement of OER is the necessity for a considerably higher overpotential than the theoretical oxygen evolution potential, due to the sluggish kinetics of the electron transfer reaction, which involves a large amount of thermodynamic energy. In this article, amorphous and cauliflower-like Co-P electrocatalysts were in situ grown on nickel foam by dynamic hydrogen bubble template (DHBT) electrodeposition method. The Co-P electrocatalyst with Co/P ratio optimal presented excellent electrocatalytic activities with a low overpotential of 239 mV for OER at 10 mA·cm−2 and long-term stability in 1.0 M KOH. The outstanding OER performance of the catalyst is mainly attributed the synergistic effect of amorphous and cauliflower-like structure, superhydrophilicity surface, and the electronic regulation by adjusting the atomic ratio of Co to P. This research will bring fresh ideas and strategies for developing novel simple, affordable, and efficient electrocatalysts to boost OER kinetics.

Polyhydroxykanoate-Assisted Photocatalytic TiO2 Films for Hydrogen Production.

The photocatalytic production of hydrogen using biopolymer-immobilized titanium dioxide (TiO2) is an innovative and sustainable approach to renewable energy generation. TiO2, a well-known photocatalyst, benefits from immobilization on biopolymers due to its environmental friendliness, abundance, and biodegradability. In another way, to boost the efficiency of TiO2, its surface properties can be modified by incorporating co-catalysts like platinum (Pt) to improve charge separation. In this work, the surface of commercial TiO2 PC500 was modified with Pt nanoparticles (Pt1%@PC500) and then immobilized on glass surfaces using polyhydroxyalkanoate biopolymer poly(hydroxybutyrate-co-hydroxyhexanoate) (PHBH). The as-prepared immobilized Pt-modified TiO2 photocatalysts were fully characterized using various physicochemical techniques. The photocatalytic activity of the photocatalyst film was investigated for photocatalytic hydrogen production through water reduction using ethanol as a sacrificial donor. The impact of the film preparation conditions, e.g., PHBH concentration, PHBH:catalyst ratio, and temperature, on activity and stability was studied in detail. The application of biopolymer PHBH as a binder provides a green alternative to conventional immobilization methods, and with the application of PHBH, a stable and active photocatalyst film that showed lower activity compared to that of the suspended photocatalyst but good recyclability in six runs was prepared. A long-term photocatalytic hydrogen production experiment was carried out. In 98 h of operation, 12 mmol of hydrogen was produced in three consecutive runs with a PHBH/Pt1%@PC500 film having an area of ∼5.3 cm2. A significantly lower hydrogen productivity was observed after the first run, possibly due to a change in film structure, but thereafter, the productivity remained almost constant for the second and third runs. Hydrogen was the main product in the gas phase (90%), but carbon dioxide (4-5%) and methane (4-5%) were obtained as important byproducts. The byproducts are a consequence of the use of the sacrificial reagent ethanol. The results of the film performance are very promising, with regard to large-scale continuous hydrogen production.

Dual chalcogenide coordination engineering on a self-supported alloy electrode for enhanced hydrogen evolution reaction.

The electrochemical hydrogen evolution reaction (HER) holds substantial promise for large-scale green hydrogen production due to its cost-effectiveness, high performance, and scalability for repeated implementation. A promising strategy that involves a novel transition-metal chalcogenide with a self-supported framework can improve the reaction kinetics in the HER. We synthesize a nano three-dimensional self-supported HER catalyst via a straightforward one-step chemical vapor deposition process. This method incorporates a dual co-reaction with sulfur (S) and selenium (Se) onto a commercially available Monel alloy (CNSSe). The dynamics ion exchange redox reactions promote the formation of heterogeneous catalyst structures. Density functional theory (DFT) calculations indicate that the CNSSe catalyst exhibits low hydrogen coverage, as evidenced by a thermoneutral free energy of adsorbed hydrogen (ΔGH*) of 0.105 eV, which can be attributed to the dual introduction of S and Se. Consequently, the optimized CNSSe electrocatalyst achieves an enhancement in HER performance exceeding 100% compared to catalysts introduced exclusively with either S or Se. These results underscore the substantial potential of the optimized CNSSe electrocatalyst to improve both the performance and economic feasibility of HER technologies in alkaline water electrolysis.

Regulation of Oxide Pathway Mechanism for Sustainable Acidic Water Oxidation.

The advancement of acid-stable oxygen evolution reaction (OER) electrocatalysts is crucial for efficient hydrogen production through proton exchange membrane (PEM) water electrolysis. Unfortunately, the activity of electrocatalysts is constrained by a linear scaling relationship in the adsorbed evolution mechanism, while the lattice-oxygen-mediated mechanism undermines stability. Here, we propose a heterogeneous dual-site oxide pathway mechanism (OPM) that avoids these limitations through direct dioxygen radical coupling. A combination of Lewis acid (Cr) and Ru to form solid solution oxides (CrxRu1-xO2) promotes OH adsorption and shortens the dual-site distance, which facilitates the formation of *O radical and promotes the coupling of dioxygen radical, thereby altering the OER mechanism to a Cr-Ru dual-site OPM. The Cr0.6Ru0.4O2 catalyst demonstrates a lower overpotential than that of RuO2 and maintains stable operation for over 350 h in a PEM water electrolyzer at 300 mA cm-2. This mechanism regulation strategy paves the way for an optimal catalytic pathway, essential for large-scale green hydrogen production.

Contribution of Copper Slag to Water Treatment and Hydrogen Production by Photocatalytic Mechanisms in Aqueous Solutions: A Mini Review.

Hydrogen has emerged as a promising energy carrier, offering a viable solution to meet our current global energy demands. Solar energy is recognised as a primary source of renewable power, capable of producing hydrogen using solar cells. The pursuit of efficient, durable, and cost-effective photocatalysts is essential for the advancement of solar-driven hydrogen generation. Copper slag, a by-product of copper smelting and refining processes, primarily consists of metal oxides such as hematite, silica, and alumina. This composition makes it an attractive secondary resource for use as a photocatalyst, thereby diverting copper slag from landfills and generating 0.113 μmol/g h of hydrogen, as noted by Montoya. This review aims to thoroughly examine copper slag as a photocatalytic material, exploring its chemical, physical, photocatalytic, and electrochemical properties. Additionally, it evaluates its suitability for water treatment and its potential as an emerging material for large-scale solar hydrogen production.

The role of FexCu(1‒x) electrodeposits from a deep eutectic solvent in promoting the hydrogen evolution reaction

Hydrogen from water splitting is more powerful, clean, and more energy-efficient than fossil fuels. Since the electrode material influences the performance and operating cost of industrial electrolyzers, this work induces technological innovation through FexCu(1−x) alloys with electrocatalytic action toward the hydrogen evolution reaction (HER). The materials were galvanostatically deposited on 1020 carbon steel. It was used electrolytes formulated with deep eutectic solvents (DES) and aqueous solvents (AQS) were used to verify their influence on the coatings' composition, morphology, and electrocatalytic activity. The results proved that even after fixing the operating conditions (electrochemical potential, current density, and deposition time), the alloys produced in DES are richer in Fe (≅ 77-85%, w/w). For comparison, those obtained from AQS have greater proportion of Cu (≅ 65%, w/w). Stoichiometry changes also alter the topography, surface area, and electrocatalytic activity of FexCu(1−x) alloys for hydrogen production. The electrochemical studies carried out also revealed that the association between Fe and Cu as alloying elements has a positive synergistic effect of reducing the HER overpotential by around 125 mV, using 1 mol L−1 KOH at 296 K. Considering stability and resistance to corrosion, FexCu(1−x) alloys produced in DES stood out as the most promising for possible adaptation in electrolyzers developed for large-scale hydrogen production.

Boosted Hydrogen evolution reaction based on synergistic effect of graphene, MoS2 and RuO2 ternary electrocatalyst

Hydrogen holds the promise of replacing fossil fuels and offers a sustainable pathway for energy generation. However, the large-scale production of hydrogen via the environment friendly electrocatalytic process relies heavily on the performance of electrocatalysts. In this study, we investigate the electrocatalytic performance of graphene nanosheets (GNS), molybdenum disulfide (MoS2), ruthenium dioxide (RuO2), and their composites for hydrogen evolution reaction (HER), a novel combination that has not been explored in previous literature. We synthesize the materials using Liquid Phase Exfoliation at 500 and 1000 RPMs for GNS and MoS2 and via hydrothermal methods for RuO2 nanosheets and nanoparticles, aiming to exploit synergistic effects for enhanced activity and stability. The synthesized GNS-1000/MoS2-1000/RuO2-NSs composite demonstrates promising HER results, showcasing a low overpotential of 63 mV and a reduced Tafel slope of 59 mV/dec. This improvement indicates enhanced electron transfer, improved active site dispersion, and increased surface area due to the synergistic effects, which also aids in long-term electrochemical stability. Our study underlines the potential of GNS/MoS2/RuO2 composites, particularly the GNS-1000/MoS2-1000/RuO2-NSs, in transforming hydrogen production methods and promoting efficient, sustainable energy solutions. The implications of our findings extend the boundaries of materials engineering, edging us closer to a sustainable energy future.

Sustained hydrogen production through alkaline water electrolysis using Bridgman–Stockbarger derived indium-impregnated copper chromium selenospinel

The depletion of conventional fossil fuels necessitates the development of sustainable energy alternatives, with electrochemical water splitting for hydrogen (H2) production being a promising solution. However, large-scale hydrogen generation is hindered by the scarcity of cost-effective electrocatalysts to replace noble metals such as Pt and RuO2 in the Oxygen Evolution Reaction (OER) and Hydrogen Evolution Reaction (HER). In this study, we report the synthesis of CuCr2-xInxSe4 (x = 0, 0.2, 0.4) using a dual approach combining the Bridgman-Stockbarger method and ball milling. Among the synthesized materials, CuCr1.8In0.2Se4 demonstrates outstanding HER activity in 1.0 M KOH, achieving a potential of −0.16 V vs. RHE at a current density of 10 mA cm−2. Moreover, the material shows remarkable durability during a three-electrode accelerated degradation test in an alkaline medium, maintaining its performance over 24 h at a constant current density of −200 mA cm−2, with a stable potential of −0.57 V vs. RHE. Additionally, CuCr1.8In0.2Se4 was tested in a two-electrode configuration alongside CoFe LDH, achieving a benchmark of 1.7 V for overall water splitting. It sustained a current density of 400 mA cm−2 for 24 h in an accelerated degradation test, exhibiting a minimal loss of 0.1 V after the testing period. These results highlight CuCr1.8In0.2Se4 as a promising non-noble metal catalyst for HER, demonstrating its potential to reduce reliance on noble materials for large-scale hydrogen production.

Rational Design of Ultrahigh-Loading Ir Single Atoms on Reconstructed Mn─NiOOH for Enhanced Catalytic Performance in Urea-Water Electrolysis.

Investigating advanced electrocatalysts is crucial for improving the efficacy of water splitting to generate environmentally friendly fuel. The discovery of highly effective electrocatalysts, capable of driving oxygen evolution reaction (OER) and urea oxidation reaction (UOR) in urea-alkaline environments, is pivotal for advancing large-scale hydrogen production. This study aims to introduce a new method that involves creating nanosheets of high-loading iridium single atoms embedded in a manganese-containing nickel oxyhydroxide matrix (Ir@Mn─NiOOH). These nanostructures are derived from self-supported hydrate pre-catalyst nanosheets grown on nickel foam and then activated through electrochemical etching pretreatment. The Ir@Mn─NiOOH nanoarchitecture displays outstanding electrocatalytic activity, having a low overpotential of just 258mV and a potential of 1.319V (at 10mAcm-2) for OER and UOR, respectively. Such extraordinary catalytic characteristics of Ir@Mn─NiOOH is mainly owing to the strong synthetic electronic interaction between Ir single atoms and Mn─NiOOH, which can change its electronic characteristics and boost electrochemical catalytic sites. This research presents a new way to produce exceptionally efficient catalysts by adding a synergistic effect to complex multi-electron processes.

Electronic Structure Engineering of Single-Atom Tungsten on Vacancy-enriched V3S4 Nanosheets for Efficient Hydrogen Evolution.

Constructing single-atom catalysts (SACs) and optimizing the electronic structure between metal atoms and support interactions is deemed one of the most effective strategies for boosting the catalytic kinetics of the hydrogen evolution reaction (HER). Herein, a sulfur vacancy defect trapping strategy is developed to anchor tungsten single atoms onto ultrathin V3S4 nanosheets with a high loading of 25.1wt.%. The obtained W-V3S4 catalyst exhibits a low overpotential of 54mV at 10mA cm-2 and excellent long-term stability in alkaline electrolytes. Density functional theory calculations reveal that the in situ anchoring of W single atoms triggers the delocalization and redistribution of electron density, which effectively accelerates water dissociation and facilitates hydrogen adsorption/desorption, thus enhancing HER activity. This work provides valuable insights into understanding highly active single-atom catalysts for large-scale hydrogen production.

Interfacial Electronic Structure Engineering of NiCo2Se4 and NiTe2 Nanorods for Enhanced Hydrogen Evolution Reaction.

Finding the best candidates with outstanding electrocatalytic capabilities for the hydrogen evolution reaction is essential for realizing large-scale hydrogen production through electrolysis. In this study, we synthesized NiCo2Se4 (NCS) and NiTe2 (NT) nanorod arrays using a hydrothermal method. The confirmation of catalyst formation was achieved through X-ray diffraction analysis, electron microscopy imaging, and X-ray photoelectron spectroscopy. Leveraging the plentiful heterointerfaces and synergistic effects arising from the incorporation of bimetallic components, the NCS/NT electrocatalyst demonstrates remarkable efficacy in catalyzing the hydrogen evolution reaction. It achieves a minimal overpotential of 163 mV to attain a current density of 50 mA cm-2, showcasing exceptional catalytic activity. Further exploration has revealed that the engineering of heterogeneous interfaces and the morphology of nanorods not only guarantee the exposure of numerous active sites and expedite electron-mass transfer but also trigger electron modulation. Such modulation serves to fine-tune the adsorptive and desorptive dynamics of reaction intermediates, culminating in an enhancement of the catalyst's inherent activity. This study illuminates the novel composite electrocatalyst with robust synergy, highlighting the pivotal role of their unique nanostructures in achieving high-efficiency hydrogen production via electrolysis.

A gradient porous transport layer enabling a high-performance proton-exchange membrane electrolysis cell

Large-scale green hydrogen production through proton-exchange membrane electrolysis cells (PEMECs) is constrained by high costs. Operating PEMECs at high current densities while minimizing overpotentials, particularly the mass transport overpotential due to intense water-oxygen two-phase flow, is crucial. The porous transport layer (PTL) plays a key role in facilitating water-oxygen two-phase flow and affecting ohmic resistance and catalyst utilization. In this study, a gradient PTL has been developed by introducing titanium mesh with tunable pores between the titanium felt and the flow field. The woven mesh structure with large pores facilitates water transport under the ribs, while the titanium felt reduces ohmic resistance and improves catalyst utilization. Experimental results demonstrate that the gradient PTL with a single layer of titanium mesh (pore size: 0.6 mm) can reduce the mass transport overpotential from 0.478 V to 0.206 V at 5 A/cm2 and maintain low ohmic and activation overpotentials compared with the conventional PTLs. Additionally, the gradient PTL with two titanium mesh layers (pore sizes: 0.6 mm and 0.28 mm) can further facilitate water transport, reducing mass transport overpotential to 0.149 V at 5 A/cm2. Numerical simulations reveal that the developed gradient PTL increases the volume fraction of liquid water and ensures uniform water distribution in the catalyst layer. The combined results indicate that the gradient PTL design is promising for enhancing mass transport performance while maintaining low ohmic resistance and high catalyst utilization, making PEMECs more viable for large-scale hydrogen production.

Amorphous/crystalline Ni-Fe based electrodes with rich oxygen vacancies enable highly active oxygen evolution in seawater electrolysis

To realize large-scale production of hydrogen through seawater electrolysis, it is highly crucial to engineer high-activity and robustly stable catalytic materials for oxygen evolution reaction (OER). Here, a facile etching growth strategy based on Ni foam (NF) is employed to fabricate an amorphous/crystalline Ni-Fe based electrode with rich oxygen vacancies as a promising OER electrocatalyst (a/c-NiFeOxHy@NF). Of note, the introduction of Fe induces the generation of plentiful Ni(Fe)OOH species, which can contribute to the remarkable OER behavior. Profiting from the favorable geometric microstructure of ultrathin nanosheets coupled with 3D open-pore architecture and regulated electronic state by increased oxygen vacancies and abundant crystalline-amorphous boundaries, the resulting a/c-NiFeOxHy@NF displays prominent electrocatalytic OER activity in pure alkaline solution and seawater, achieving impressive overpotentials of only 219 and 233 mV to reach 100 mA cm−2, respectively. More significantly, the electrode can keep stable operation without obvious attenuation for over 1200 h at 100 mA cm−2, demonstrating its exceptional corrosion resistance. Such robustness of this electrode surpasses those of almost all reported OER electrocatalysts. Furthermore, in a self-assembled seawater electrolyzer with a/c-NiFeOxHy@NF as the anode and l-RuP@NF as the cathode, a large current density of 500 mA cm−2 is easily achieved at the voltage of 1.795 V at 65 °C. The work offers a novel paradigm for constructing low-cost, high-efficiency, and ultra-stable OER catalysts, which shows huge promise for industrial seawater electrolysis applications.

Selenate oxyanion-intercalated NiFeOOH for stable water oxidation via lattice oxygen oxidation mechanism

Transition metal-based compounds can serve as pre-catalysts to obtain genuine oxygen evolution reaction (OER) electrocatalysts in the form of oxyhydroxides through electrochemical activation. However, the role and existence form of leached oxygen anions are still controversial. Herein, we selected iron selenite-wrapped hydrated nickel molybdate (denoted as NiMoO/FeSeO) as a pre-catalyst to study the oxyanion effect. It is surprising to find that SeO42− exists in the catalyst in the form of intercalation, which is different from previous studies that suggest that anions are doped with residual elements after electrochemical activation, or adsorbed on the catalyst surface. The experiment and theoretical calculations show that the existence of SeO42− intercalation effectively adjusts the electronic structure of NiFeOOH, promotes intramolecular electron transfer and O–O release, and thus lowers the reaction energy barrier. As expected, the synthesized NiFeOOH-SeO only needs 202 and 285 mV to attain 100 and 1000 mA cm−2 in 1 M KOH. Further, the anion exchange membrane water electrolyzer (AEMWE) consisting of NiFeOOH-SeO anode and Pt/C cathode can reach 1 A cm−2 at 1.70 V and no significant attenuation within 300 h. Our findings provide insights into the mechanism, by which the intercalated oxyanions enhance the OER performance of NiFeOOH, thereby facilitating large-scale hydrogen production through AEMWE.

Oxygen-coordinated cobalt single atom steered by doped-O and CoO for efficient hydrogen evolution at industrial current densities

The exploration and design of highly active, low-cost, transition metal-based electrocatalysts are crucial for large-scale green hydrogen production. Here, the heterostructure of oxygen-coordinated cobalt single atoms with O-doped carbon and CoO nanowires (Co-O-C-O/CoO/CF) is constructed for efficient and stable HER at industrial current densities. Benefiting from the synergistic effect of O doping and CoO nanowires, Co-O-C-O/CoO/CF exhibits extremely low overpotentials of 24.8, 229, and 239 mV to achieve current densities of 10, 500, and 1000 mA cm−2 in 1.0 M KOH solution, respectively, and operates stably for 1000 h at 1000 mA cm−2. Additionally, when coupled with NiFe-LDH in a self-assembled electrolyzer, it delivers a high current density of 1000 mA cm−2 at 1.97 V, along with outstanding stability, outperforming Pt/C||NiFe-LDH and most reported electrolyzers. Density functional theory (DFT) calculations reveal that the optimized d-band center and binding strength of H* and OH* intermediates for Co-O-C-O/CoO/CF lower the energy barrier of the rate-determining step. This work provides a new pathway for engineering Co-based catalysts for green hydrogen production at industrial current densities.

A Review of Stoichiometric Nickel Sulfide-Based Catalysts for Hydrogen Evolution Reaction in Alkaline Media

Efficient and cost-effective catalysts for hydrogen evolution reaction (HER) are essential for large-scale hydrogen production, which is a critical step toward reducing carbon emissions and advancing the global transition to sustainable energy. Nickel sulfide-based catalysts, which exist in various stoichiometries, show promise for HER in alkaline media. However, as single-phase materials, they do not demonstrate superior activity compared to Pt-based catalysts. This review highlights recent strategies to enhance the HER performance of nickel sulfides, including heteroatom doping, heterostructure construction, and vacancy engineering, tailored to their different stoichiometric ratios. The study also examines synthesis methods, characterizations, and their impact on HER performance. Furthermore, it discusses the challenges and limitations of current research and suggests future directions for improvement.

Chitosan–sodium Tripolyphosphate–CuO Biopolymer–nanocomposite as an Efficient Electrocatalyst for Water Splitting

Background: Fossil fuels have been used extensively as primary energy sources, which has resulted in nearly depleted reserves, a contaminated environment, and a variety of negative health effects globally. Hydrogen has been proposed by researchers as an effective “carbon neutral” fuel. Large-scale hydrogen production through electrochemical water splitting necessitates the use of inexpensive, extremely effective, and earth-abundant electrocatalysts. Method: In this study, chitosan–sodium tripolyphosphate (TPP) nanoparticles are combined with CuO nanostructures to produce chitosan–TPP–CuO (CT/CuO) nanocomposite. Chitosan–TPP nanoparticles were first synthesized using the ionic gelation method. These nanoparticles were then extracted, and CuO was synthesized in situ in polymer nanoparticles using a simple chemical precipitation method. Chitosan and CuO are abundantly available and are environmentally beneficial materials. The porous structure and open channels within the chitosan polymer matrix host the CuO nanostructures, which promote electrolyte penetration, mass transport, and charge transfer, while the metal-oxide nanostructures act as catalytic centers. The structural and morphological properties of the CT/CuO nanocomposite were investigated using XRD, HRSEM, and HRTEM. The band gap and functional groups in the material were measured by UV–Vis DRS and FTIR methods, respectively. Elemental analysis was conducted utilizing EDS, HRSEM, and XPS. Thermal characteristics of the CT/CuO nanocomposite were investigated using TG-DTA and DSC methods. Electrochemical techniques were used to investigate the activities of HER and OER. Results: The XRD examination of the CT/CuO nanocomposite revealed semi-crystalline chitosan peaks and a monoclinic CuO structure. HRSEM and HRTEM pictures indicated that chitosan–TPP nanoparticles and CuO nanostructures were evenly spread and clustered to create a nanoparticulate matrix. UV–Vis DRS indicated that the CT/CuO nanocomposite had a direct band gap of 1.702 eV. The FTIR and XPS studies revealed the various bonds and oxidation states of the nanocomposite. Thermal analyses demonstrated that the inclusion of CuO increased the thermal stability of the CT/CuO nanocomposite. CT/CuO nanocomposite exhibited excellent OER and HER activity, requiring a low overpotential of 444 mV and 379 mV at 10 mA cm−2 and -10 mA cm−2, respectively. Conclusion: Biopolymer metal-oxide nanocomposites could potentially be used as electrocatalysts in water splitting, energy conversion, storage devices, sensors, and several other fields.

Design and Optimization of Large-Scale Green Liquid Hydrogen Production Integrated with Heat Recovery and Absorption Precooling

Design and Optimization of Large-Scale Green Liquid Hydrogen Production Integrated with Heat Recovery and Absorption Precooling

Determination of hydrogen fuel production from GIS-based selected ponds using hybrid renewable energy systems in Kayseri

This study offers the feasibility study of large-scale hydrogen production to establish environmentally friendly hybrid energy facilities based on wind and solar energy resources in the vicinity of lakes and rivers within the Kayseri region of Türkiye. The ultimate objective is to enable hydrogen production from lakes and rivers and identify optimal locations for the installation of hydrogen fuel stations. The precise selection of locations for the designated province is based on geographical, environmental, and infrastructural considerations by utilizing GIS technology which allows spatial analysis and superimposition of various layers. The methodology also involves the utilization of the HOMER software to facilitate the integration of wind and solar power, along with hydrogen production, providing a platform for environmentally friendly energy system design and optimization. A comprehensive evaluation has been conducted for the sizing and placement of renewable energy systems based on microgrid analysis, the design of hydrogen production facilities, and the establishment of hydrogen refueling infrastructure. The study also incorporates a financial analysis to assess the economic viability of the project over its lifecycle. Among the five water sources considered, the highest annual hydrogen production is 830 tons in Zamantı River, while Kızılırmak River has the lowest value according to LCOE and LCOH values, 0.030 $/kWh and 3.85 $/kgH2, respectively.

In-situ exfoliating graphene to anchor Mo2C NPs and modulate crystal planes for hydrogen production

An economical and efficient noble metal-free catalyst is necessary for large-scale hydrogen production. Here, Mo2C nanoparticles (NPs) were well-dispersed on the surface of 2D graphene nanosheets by in-situ propping oxide graphene (GO) layers, anchoring molybdate ions between GO layers and pyrolysis. The exposed crystal planes were also adjusted by above strategy. The results indicate that uniform and well-dispersed Mo2C NPs with a narrow size distribution were anchored on 2D rGO nanosheets and exposed dual crystal planes. The results of hydrogen evolution reaction (HER) show that the optimal Mo2C/rGO catalyst only needs low overpotential (η10, 112 mV) to drive 10 mA cm−2 in alkaline solution, and η10 only increased by 12 mV after 1000 cycles test, indicating high activity and stability for HER. Notably, the overpotential is below than that of Pt/C commercial catalyst when current density is more than 100 mA cm−1. The excellent performance is benefit from low hydrogen adsorption Gibbs free energy (ΔGH∗) on the Mo2C catalyst. Therefore, the proposed strategy is efficient to prepare well-dispersed and dual crystal planes-exposed Mo2C NPs for electrocatalytic hydrogen evolution.