Large Hadron Collider Luminosity Upgrade Research Articles

Gain reduction mechanism observed in Low Gain Avalanche Diodes

Low Gain Avalanche Diodes (LGADs) is one of the candidate sensing technologies for future 4D-tracking applications and recently have been qualified to be used in the ATLAS and CMS timing detectors for the CERN High Luminosity Large Hadron Collider upgrade. LGADs can achieve an excellent timing performance by the presence of an internal gain that improves the signal-to-noise ratio leading to a better time resolution.These detectors are designed to exhibit a moderate gain with an increase of the reverse bias voltage. The value of the gain strongly depends on the temperature. Thus, these two values must be kept under control in the experiments to maintain the gain within the required values. A reduction in the reverse bias or an increase in the temperature will reduce the gain significantly.In this paper, a mechanism for gain reduction in LGADs is going to be presented. It was observed, that the gain measured in these devices depends on the charge density projected into the gain layer, generated by a laser or a charged particle in their bulk. Measurements performed with different detectors showed that ionizing processes that induce more charge density in the detector bulk lead to a decrease in the detector’s measured gain.Measurements conducted with an IR-laser and a Sr-90 in the lab, modifying the charge density generated in the detector bulk, confirmed this mechanism and will be presented here.

Pre-Load Studies on a 2-m Long Nb3Sn 11 T Model Magnet for the High Luminosity Upgrade of the LHC

The Large Hadron Collider luminosity upgrade requires the replacement of standard 8.3 T Nb-Ti main dipole magnets with pairs of shorter 11 T Nb <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">3</sub> Sn dipole magnets. After the manufacturing and testing of several 2 m-long 11 T models, the full-length 11 T magnet series production is now ongoing. As a result of a degraded quench performance in several short models, attributed to excessive stress in the coils' midplanes, an upper hard limit for the coils' pre-stress was set to avoid any conductor degradation. With the aim of further investigating the influence of a lower pre-stress, an additional double-aperture short model was manufactured. The first aperture was assembled with the standard pre-stress target, in line with the series production. The second aperture was assembled with half of the standard pre-stress. Both apertures were then assembled into a 2-in-1 structure, but connected individually in order to power them independently to allow for comparison studies. Contrary to previously built 11 T magnets, the conductor type is also different as Powder-in-tube (PIT) cable was used, instead of standard Restacked-Rod-Process (RRP) cable. Additionally, the quench heaters for magnet protection were not impregnated as previously done, but placed on the outer radial surface of the coils, in agreement with the final decision for the 11 T series production. This paper describes the manufacturing and testing campaign results of this last 11 T short model.

The Development of the Superconducting Dipoles D2 for the High Luminosity Upgrade of LHC

The recombination dipoles D2 (MBRD) for the luminosity upgrade of the Large Hadron Collider (LHC) are double aperture magnets to be placed on each side of ATLAS and CMS experiments, generating 4.5 T along a magnetic length of 7.78 m and a bore diameter of 105 mm. Its development plan foresees the construction of a short model 1.6 m long, followed by a prototype and by the series of 6 magnets. The magnet design was carried out at INFN Genova in a collaboration framework with CERN and the construction is ongoing in the industry (ASG Superconductors, Italy). The short model activities have just been accomplished after a successful power test performed at CERN, while the prototype is in its construction phase. In this contribution, the main features of the D2 magnet will be described, underlining the improvements implemented in the prototype with respect to the short model design. Then, the main results of the power test will be presented, focusing on training performance, protection scheme effectiveness and magnetic measurements.

Humidity sensitivity of large area silicon sensors: Study and implications

The production of large area sensors is one of the main challenges that the ATLAS collaboration faces for the new Inner-Tracker full-silicon detector. During the prototype fabrication phase for the High Luminosity Large Hadron Collider upgrade, several ATLAS institutes observed indications of humidity sensitivity of large area sensors, even at relative humidities well below the dew point. Specifically, prototype Barrel and End-Cap silicon strip sensors fabricated in 6-inch wafers manifest a prompt decrease of the breakdown voltage when operating under high relative humidity, adversely affecting the performance of the sensors. In addition to the investigation of these prototype sensors, a specific fabrication batch with special passivation is also studied, allowing for a deeper understanding of the responsible mechanisms.This work presents an extensive study of this behaviour on large area sensors. The locations of the hotspots at the breakdown voltage at high humidity are revealed using different infrared thermography techniques. Several palliative treatments are attempted, proving the influence of sensor cleaning methods, as well as baking, on the device performance, but no improvement on the humidity sensitivity was achieved. Furthermore, a study of the incidence of the sensitivity in different batches is also presented, introducing a hypothesis of the origins of the humidity sensitivity associated to the sensor edge design, together with passivation thickness and conformity. Several actions to be taken during sensor production and assembly are extracted from this study, in order to minimize the impact of humidity sensitivity on the performance of large area silicon sensors for High Energy Physics experiments.

Mechanical analysis of the Nb3Sn 11 T dipole short models for the High Luminosity Large Hadron Collider

For the Large Hadron Collider luminosity upgrade, two of the NbTi 8.3 T main bending dipoles will be replaced by two shorter Nb3Sn 11.2 T dipoles to create space for the installation of collimators in the dispersion suppression region. With the aim to verify the design features, several 2 m long 11 T models have been constructed and tested at CERN. During the fabrication and assembly of, so far, seven single and two double aperture short model magnets, several challenges were identified and tackled. These include reproducibility in coil fabrication and assembly procedure, as well as control of mechanical stresses in the conductor and surrounding structure. In order to limit coil over-compression and improve reproducibility, the cable insulation was re-optimized. In addition, a review of the collaring procedure of the 11 T magnet was launched with the goal of reducing the risk of conductor degradation due to excessive stress. In this paper, the main fabrication and assembly steps are described, including the description of the actions taken to resolve the identified weakness.

A data acquisition system for HV-CMOS sensor research and development in the upgrade of ATLAS experiment.

In the high luminosity Large Hadron Collider upgrade of the A Toroidal LHC ApparatuS (ATLAS) experiment in 2026, the new inner tracker detector will be installed. As a promising candidate for the outer layer of the inner tracker detector, the High Voltage CMOS (HV-CMOS) pixel sensors are being investigated by the ATLAS collaboration. A Front-End LInk eXchange (FELIX) based Data Acquisition (DAQ) system is developed for the R&D of the HV-CMOS sensors. A FELIX card with a Peripheral Component Interconnect express interface in the back-end is used to control, monitor, calibrate, and read out the front-end electronics. In the front-end, a Xilinx evaluation board ZC706 works as the interface between the back-end and the custom boards with HV-CMOS sensors and the readout Application-Specific Integrated Circuit. The DAQ system was successfully deployed for the testbeam experiment at CERN. The design of the DAQ system, the tuning of sensors, and the testbeam results will be described in details.

Field Measurement to Evaluate Iron Saturation and Coil End Effects in a Modified Model Magnet of Beam Separation Dipole for the HL-LHC Upgrade

A beam separation dipole magnet for the high luminosity large hadron collider upgrade is developed. The development of the 2-m-long model magnet (MBXFS1) was initiated so as to evaluate the design and performance of the beam separation dipole magnet. In the first cold test in 2016, the quench performance was not satisfactory because the coil prestress at the pole was completely released during excitation. After reassembly to improve the quench performance, the excitation test of the modified model magnet (MBXFS1b) was performed at 1.9 K in 2017 at KEK. Due to the large coil aperture and limited outer diameter of the iron yoke, the control of iron saturation effects on the field quality has been a design issue. Regarding the magnetic performance, field saturation effects on the transfer function and the multipole field variation along the excitation, and coil end effects to the straight section need to be evaluated by the field measurement. In this paper, field measurement results will be presented and the comparison with the three-dimensional field calculation will be discussed.

Influence of 3-D Effects on Field Quality in the Straight Part of Accelerator Magnets for the High-Luminosity Large Hadron Collider

A dedicated D1 beam separation dipole is currently being developed at KEK for the large hadron collider luminosity upgrade (HL-LHC). Four 150-mm aperture, 5.6-T magnetic field, and 6.7-m-long Nb–Ti magnets will replace resistive D1 dipoles. The development includes fabrication and testing of 2.2-m model magnets. The dipole has a single-layer coil and thin spacers between coil and iron, giving a nonnegligible impact of saturation on field quality at nominal field. The magnetic design of the straight section coil cross section is based on two-dimensional (2-D) optimization and a separate optimization concerns the coil ends. However, magnetic measurements of the short model showed a large difference (tens of units) between the sextupole harmonic in the straight part and the 2-D calculation. This difference is correctly modeled only by a 3-D analysis: 3-D calculations show that the magnetic field quality in the straight part is influenced by the coil ends, even for the 6.7-m-long magnets. The effect is even more remarkable in the short model. We investigate similar 3-D effects for other magnets, namely the 11-T dipole for HL-LHC. We also consider the case of the 4.5-T recombination magnets for HL-LHC (D2), where the larger space between coil and iron makes this effect less important, but still visible. We conclude the paper by outlining the different classes of accelerator magnets, where this coupling between 3-D effects and iron saturation can be relevant.

Magnetic Field Measurement of 2-m-Long Model of Beam Separation Dipole for the HL-LHC Upgrade

KEK has been developing a beam separation dipole magnet for the high luminosity large hadron collider upgrade. The magnet has a coil aperture of 150 mm and uses NbTi superconducting cable. A dipole magnetic field of 5.6 T is generated at 12 kA at 1.9 K to provide a field integral of 35 T·m. KEK has started the development of the first 2-m-long model magnet to evaluate the design and performance of the beam separation dipole magnet. The excitation test at 1.9 K of the first 2-m-long model magnet was performed from April to June 2016 at KEK. This paper presents the results of the magnetic field measurements of the first 2-m-long model magnet by a rotating coil probe.

Magnetic Analysis of the Nb3Sn Low-Beta Quadrupole for the High-Luminosity LHC

Author(s): Bermudez, SI; Ambrosio, G; Chlachidze, G; Ferracin, P; Holik, E; Di Marco, J; Todesco, E; Sabbi, GL; Vallone, G; Wang, X | Abstract: As part of the Large Hadron Collider Luminosity upgrade (HiLumi-LHC) program, the US LARP collaboration and CERN are working together to design and build 150-mm aperture Nb3Sn quadrupoles for the LHC interaction regions. A first series of 1.5-m-long coils were fabricated, assembled, and tested in the first short model. This paper presents the magnetic analysis, comparing magnetic field measurements with the expectations and the field quality requirements. The analysis is focused on the geometrical harmonics, iron saturation effect, and cold-warm correlation. Three-dimensional effects such as the variability of the field harmonics along the magnet axis and the contribution of the coil ends are also discussed. Moreover, we present the influence of the conductor magnetization and the dynamic effects.

Mechanical Design Studies of the MQXF Long Model Quadrupole for the HiLumi LHC

The Large Hadron Collider Luminosity upgrade (HiLumi) program requires new low-β triplet quadrupole magnets, called MQXF, in the interaction region to increase the LHC peak and integrated luminosity. The MQXF magnets, designed and fabricated in collaboration between CERN and the U.S. LARP, will all have the same cross section. The MQXF long model, referred as MQXFA, is a quadrupole using the Nb3Sn superconducting technology with 150 mm aperture and a 4.2 m magnetic length and is the first long prototype of the final MQXF design. The MQXFA magnet is based on the previous LARP HQ and MQXFS designs. In this paper, we present the baseline design of the MQXFA structure with detailed three-dimensional (3-D) numerical analysis. A detailed tolerance analysis of the baseline case has been performed by using a 3-D finite element model, which allows fast computation of structures modeled with actual tolerances. Tolerance sensitivity of each component is discussed to verify the actual tolerances to be achieved by vendors. Tolerance stack-up analysis is presented in the end of this paper.

Design Optimization of the Nb3Sn 11 T Dipole for the High Luminosity LHC

As a part of the large hadron collider luminosity upgrade (HiLumi-LHC) program, CERN is planning to replace some of the 8.33-T 15-m-long Nb-Ti LHC main dipoles with shorter 11 T Nb3Sn magnets providing longitudinal space for additional collimators. Whereas the present design of the 11 T dipole enables the use of RRP conductor with critical current degradation after cabling at the level of 5%, new cross sections of the cable have been studied in order to further decrease the degradation of both critical current and resistivity of the copper matrix. This change is particularly beneficial for the PIT conductor. The coil layout is reoptimized to accommodate the new cable geometry, using the ROXIE code. A set of additional design changes are implemented, such as reduction of the outer yoke diameter. In this paper, we review the main parameters of the present design, describe the changes implemented in the new design, and discuss their impact on both the electromagnetic and structural properties.

Progress on the Development of the Nb3Sn 11T Dipole for the High Luminosity Upgrade of LHC

The high-luminosity large hadron collider (LHC) project at CERN entered into the production phase in October 2015 after the completion of the design study phase. In the meantime, the development of the 11 T dipole needed for the upgrade of the collimation system of the machine made significant progress with very good performance of the first two-in-one magnet model of 2-m length made at CERN. The 11 T dipole, which is more powerful than the current main dipoles of LHC, can be made shorter with an equivalent integrated field. This will allow creating space for the installation of additional collimators in specific locations of the dispersion suppressor regions. Following tests carried out during heavy ions runs of LHC in the end of 2015, and a more recent review of the project budget, the installation plan for the 11 T dipole was revised. Consequently, one 11 T dipole full assembly containing two 11 T dipoles of 5.5-m length will be installed on either side of interaction point 7. These two units shall be installed during the long shutdown 2 in years 2019-2020. After a brief reminder on the design features of the magnet, this paper describes the current status of the development activities, in particular the short model programme and the construction of the first full scale prototype at CERN. Critical operations such as the reaction treatment and the coil impregnation are discussed, the quench performance tests results of the two-in-one model are reviewed and finally, the plan toward the production for the long shut down 2 is described.

New Analysis Framework Software for the CERN Superconducting Magnet Test Facility

Since 2013, the existing but aging analysis tools that were routinely used for the large hadron collider (LHC) magnet series production measurement campaigns conducted at the CERN superconducting Magnet Test Facility (SM18) are being replaced by a novel open-data and user-driven analysis environment. This effort is running in parallel to the current development of magnet prototypes in the framework of the High Luminosity Upgrade of the CERN LHC (HL-LHC project). This R&D phase requires new features in the quench analysis software to cope with the dedicated or specific magnet tests (splice resistance, inductance, ac loss, Quench Heater efficiency, Hot Spot Temperature assessment, etc…), as well as a more open access to the mathematical routines and to the output results. The new data handling and analysis tools framework that is currently deployed is based on two pillars. First, the availability of the legacy proprietary raw data in an open and widely accessible format. Second, the new possibility for the user to process with the data through dedicated numerical tools and algorithms recently developed for data viewing, analysis, and formatted test result reports. In this paper, the initial analysis framework is described in terms of the acquisition system that produces data, the conversion tool that standardizes the file format, the new analysis tool that replaces the existing quench analysis software, and the database tool that archives the summary of every test. Finally, some statistics of the current situation are presented, based on facts and results of one year of analysis working within the superconducting magnet test facility.

Design, prototyping, and testing of a compact superconducting double quarter wave crab cavity

A novel design of superconducting Crab Cavity was proposed and designed at Brookhaven National Laboratory. The new cavity shape is a Double Quarter Wave or DQWCC. After fabrication and surface treatments, the niobium proof-of-principle cavity was cryogenically tested in a vertical cryostat. The cavity is extremely compact yet has a low frequency of 400 MHz, an essential property for service for the Large Hadron Collider luminosity upgrade. The electromagnetic properties of the cavity are also well matched for this demanding task. The demonstrated deflecting voltage of 4.6 MV is well above the requirement for a crab cavity in the future High Luminosity LHC of 3.34 MV. In this paper we present the design, prototyping and test results of the DQWCC.

Fabrication of a Second-Generation of &lt;formula formulatype="inline"&gt;&lt;tex Notation="TeX"&gt;$\hbox{Nb}_{3} \hbox{Sn}$&lt;/tex&gt;&lt;/formula&gt; Coils for the LARP HQ02 Quadrupole Magnet

In the framework of the Large Hadron Collider Luminosity upgrade (HiLumi-LHC) project, the US LHC accelerator research program is developing high-gradient, large-aperture Nb3 Sn quadrupole magnets for the LHC interaction regions. The fabrication and tests of a first series of 120-mm-aperture “HQ01” coils revealed design issues that resulted in limited performance. A second series of coils was fabricated in which a number of improved features were implemented (HQ02 coils). The improvements were partly validated with the successful test of an HQ02 coil in a mirror structure, which reached 97% of the short sample. Here, we review the modifications in the coil design and the coil fabrication process, report the issues met during the fabrication, give details of the few differences that exist within the set of HQ02 coils, and discuss a list of further improvements that will be implemented in a third series of HQ coils.

Magnetic Design Optimization of a 150 mm Aperture &lt;formula formulatype="inline"&gt;&lt;tex Notation="TeX"&gt;$ \hbox{Nb}_{3}\hbox{Sn}$&lt;/tex&gt;&lt;/formula&gt; Low-Beta Quadrupole for the HiLumi LHC

As part of the Large Hadron Collider Luminosity upgrade (HiLumi) program, the US LARP collaboration and CERN are working together to design and build a 150 mm aperture <formula formulatype="inline" xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"><tex Notation="TeX">$\hbox{Nb}_{3} \hbox{Sn}$</tex></formula> quadrupole magnet that aims at providing a nominal gradient of 140 T/m. In this paper we describe the optimization process yielding the selected 2D coil cross-section and the 3D coil ends design. For the 2D optimization a sector-coil model that allows fast computation of field harmonics is used to identify, among a large number of cases, those cross-sections that provide an acceptable field quality. A more detailed analysis of these solutions is then performed and it led to the selection of an optimized cross-section from which a real coil is built by approximating sectors with blocks of cable. A 3D design of the coil ends is then realized with the Roxie software. Optimization constraints are set on the integrated multipoles, the peak field, and the coil head length.

Quench Protection Study of the $\hbox{Nb}_{3}\hbox{Sn}$ Low-$\beta$ Quadrupole for the LHC Luminosity Upgrade

In the framework of the HiLumi program, the development of high field (conductor peak field 12 T) and large aperture (150 mm in diameter) superconducting quadrupoles is under way. These quadrupoles will provide the final focusing of the beam in the interaction region of the Large Hadron Collider (LHC), in the program of the luminosity upgrade. The quench protection of these magnets is a challenging aspect, mainly for the magnet dimension (8 m long), for the large value of the stored magnetic energy (12 MJ) and for the use of Nb <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">3</sub> Sn as conductor. In this paper, the quench protection study is reported, comparing results obtained with different codes for quench analysis. The parametric analysis of the transition under different conditions for the protection scheme is also presented.

Coil End Optimization of the Nb3Sn Quadrupole for the High Luminosity LHC

As part of the Large Hadron Collider Luminosity upgrade (HiLumi-LHC) program, the US LARP collaboration and CERN are working together to design and build a 150 mm aperture quadrupole magnet that aims at providing a nominal gradient of 140 T/m. The resulting conductor peak field of more than 12 T requires the use of Nb <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">3</sub> Sn superconducting coils. In this paper the coil design for the quadrupole short model (SQXF) is described, focusing in particular on the optimization of the end-parts. We first describe the magnetic optimization aiming at reducing the peak field enhancement in the ends and minimizing the integrated multipole content. Then we focus on the analysis and tests performed to determine the most suitable shapes of end turns and spacers, minimizing the mechanical stress on the cables. We conclude with a detailed description of the baseline end design for the first series of the short model coils.

Design of a Large Single-Aperture Dipole Magnet for HL-LHC Upgrade

An upgrade of the low-beta insertion system for the ATLAS and Compact Muon Solenoid experiments is proposed in the high luminosity Large Hadron Collider upgrade project. It includes final beam focusing quadrupoles, beam separation and recombination dipoles, and larger aperture matching section quadrupoles. KEK is in charge of the conceptual design of the large aperture separation dipole D1. The latest design parameters are a main field of ~ 5 T at 1.9 K with Nb-Ti superconducting technology, a coil aperture of 160 mm, and a cos-theta one-layer coil with Large Hadron Collider dipole cable. Because the new D1 is expected to be operated in a very high radiation environment, radiation resistance and a cooling scheme are being carefully considered. The collaring-yoke structure is adopted to provide the mechanical support for the single-layer Nb-Ti coil. We summarize the design study of this magnet, including i) the very large iron saturation effect on field quality due to the large aperture and limited size of the iron yoke, ii) the stray field at the outer surface of the iron cryostat, and iii) the stress management from room temperature assembly to final operation.