Knee Joint Surface Research Articles

Finite element simulation of knee joint pressure and surface displacement: relationship and influencing factors

Knee sleeves are widely used functional pressure garments that exert pressure on the knee, causing body surface displacement and deformation. Understanding the relationship between knee joint pressure distribution and body surface displacement, along with the factors affecting this displacement, is crucial for optimizing knee sleeves. This study established a biomechanical model of the human knee joint using three-dimensional reconstruction and finite element analysis. The study simulated the pressure distribution and body surface displacement after wearing five different knee sleeve designs. Using SPSS software, it analyzed clothing and human factors to determine the main influences on displacement, resulting in linear regression equations linking knee physiological characteristics and skin displacement. Findings indicated that skin curvature radius and the distance between skin and bone significantly affect displacement, while knee sleeve structure design shows less correlation. The study also divided the knee joint into eight sections to calculate volume shrinkage after compression, providing insights for designing knee sleeves that enhance comfort and functionality based on human physiology.

Differential analysis of the impact of lesions' location on clinical and radiological outcomes after the implantation of a novel aragonite-based scaffold to treat knee cartilage defects.

There is limited comparative evidence on patient outcomes following cartilage repair in various knee compartments. The aim of this study was to compare clinical and imaging outcomes after treating cartilage defects in femoral condyles and trochlea with either an aragonite-based scaffold or surgical standard of care (SSoC, i.e., debridement/microfractures) in a large multicentre randomized controlled trial. 247 patients with up to three knee joint surface lesions (ICRS grade IIIa or above) in the femoral condyles, trochlea or both ("mixed"), were enrolled and randomized to surgery with either a cell-free aragonite scaffold or SSoC. Patients were followed for up to 48 months by analysing subjective scores (KOOS and IKDC), radiological outcomes (defect filling on MRI), as well as treatment failure rates and adverse events. A differential analysis of outcomes for condylar, trochlear and mixed lesions was performed. The scaffold group significantly outperformed the SSoC group regardless of lesion location with statistically significantly better KOOS Overall scores at 24 months (all p ≤ 0.0009) and 48 months (all p ≤ 0.02). Similar results were observed for KOOS subscales and IKDC scores. For KOOS responder rates, superiority of the implant group was demonstrated at 24, 36, and 48 months (all p ≤ 0.004). Higher defect filling on MRI for implants was observed for all locations. Lower treatment failure rates for the implant were observed in condylar and mixed lesions. The aragonite-based scaffold was safe and effective regardless of the defect location, providing superior clinical and radiological outcomes compared to SSoC up to four years follow-up. I - Randomized controlled trial.

Successful Management of Waja’al-Rukba (Knee Osteoarthritis) with Unani Pharmacopeial Poultice: A Case Study

Knee osteoarthritis (Knee OA) is the most common Musculoskeletal disorder, which causes functional disability thus, increasing the economic burden in society. In Unani medicine knee Osteoarthritis is treated with various regimens and drugs. Among these regimens, Dimād (Poultice) is prepared with several single Unani pharmacopeial drugs that exert anti-inflammatory, analgesic and anti-arthritic actions. Keeping this in mind a case study was conducted to assess the efficacy of Dimād-i-jalinus a pharmacopeial Unani formulation in the management of Knee OA. A 63-year-old female patient with chief complaints of pain and swelling in the left knee joint, joint stiffness and mild tenderness feeling severe pain while performing daily activity for the last 6 months was treated at OPD of Hakim Syed Ziaul Hasan Govt. (Auto) Unani Medical College & Hospital, Bhopal. Dimād-i-jalinus was given to the patient, in paste form and the patient was explained to use this paste over the anterior surface of the Left knee joint and the bandage was wrapped to keep the medicines in place overnight every day for 14 days. The patient was assessed at baseline, 7th day and 14th day based on changes in subjective and objective parameters with the help of Visual Analogue Scale (VAS) and Western Ontario and McMaster Universities Arthritis Index (WOMAC). The present study reveals that Dimād-i-jalinus is safe and effective in treating Knee OA without any side effects. Therefore, further randomized clinical studies need to be carried out to validate the effectiveness of Dimād-i-jalinus in the management of Knee OA.

Infrared thermogram image guided discontinuous appearances of hyaluronic acid for classification of arthritic knee joints

The liveliness of a human potentially depends on his/her smooth movability. To accomplish the work of daily life, the joints of the body need to be healthy. However, the occurrence of Rheumatoid arthritis and Osteoarthritis has a significant prevalence towards the immovability of humankind. Rheumatoid arthritis (RA) and Osteoarthritis (OA) mostly affect the joints of the hand and knee which result in lifelong pain, inability to climb, walk, etc. In the early stages, these diseases attack the synovial membrane and synovial fluid, and further it destroys the soft tissues and bone structure. By early diagnosis, we can start the treatment in the early stage which may cure these diseases with such extreme consequences. As per clinical studies of previous literature, it is observed that synovial fluid imbalance appears in the early stage of such diseases and Hyaluronic Acid (HA) concentration also decreases for that. Therefore, estimation of HA is a significant key to arthritis disease classification and grading. In this paper, we proposed a hybrid framework for classification of arthritic knee joints based on the analysis of the discontinuous appearances of the HA concentration using infrared imaging technology. To meet up the specific necessities, firstly we have proposed a modified K-Means clustering algorithm for extraction of the region of interest (ROI) i.e., the knee joint surface. Secondly, a mathematical formulation is proposed to calculate the concentration of HA from the segmented ROIs. This experimental process was implemented on the publicly available IR (Infrared) Knee Joint Dataset and for further evaluation of the novelty of mathematical formulation, we have extended the proposed work to the classification of healthy and arthritis affected knee joints depending on significant discriminative characteristics of the HA concentration with respect to the existing significant imaging features. Experimental results and analysis demonstrates that concentration of HA has the dominant potential for classifying healthy and arthritic knee joints using infrared holistic images. Our experimental analysis reveals that estimation and combination of the HA concentration features with conventional handcrafted and deep features increases the classification performance with an average accuracy of 91% and 97.22% respectively as compared to the each individual feature sets.

Double-crosslinked self-healing hydrogel alleviates osteoarthritis by protecting from wearing and targeting NF-kB signaling

Osteoarthritis (OA) is a chronic disease that causes pain, morbidity, and disability. The main strategy for OA treatment focuses on inflammation suppression, inhibition of osteoclastogenesis, and protection of articular cartilage. These functions cannot be performed effectively by monotherapy. Therefore, an effective drug delivery system is required, capable of containing and controlling the efflux of various drugs to alleviate osteoclastogenesis, protect cartilage and subchondral bone, and suppress inflammation. In this work, an encapsulation system is constructed using a self-healing chitosan hydrogel and allocated compound drugs. The self-healing gel is composed of branched-functionalized chitosan, created by simultaneously using polycaprolactone polyethylene glycol azide as a block polymer and the host-guest assembly of β-cyclodextrin and adamantane. Inhibitors of the NFkB pathway are loaded into the cavities of β-cyclodextrin and the spring-like structure of the block polymer, which can be rapidly released upon joint friction (due to the reassembly of β-cyclodextrin and adamantane by shear stress and the stretch of the block polymer). In vitro experiments using BMMs and the ATDC5 cell line confirm that the developed hydrogel can simultaneously suppress osteoclastogenesis and induce chondrogenesis. Additionally, a model of knee arthritis in C57 mice was used to confirm that this double-crosslinked encapsulation system can lubricate the knee joint surface and provide adequate protection on demand through shear-responsive drug release.

A Biomimetic Osteochondral Scaffold Augmented With Filtered Bone Marrow Aspirate for the Treatment of Joint Surface Lesions in the Knee

Background: Multilayered osteochondral scaffolds are becoming increasingly utilized for the repair of knee joint surface lesions (KJSLs). However, the literature on predictive factors is rather limited. Purpose: To (1) evaluate the clinical outcomes and safety of a combined single-step approach using a biomimetic collagen-hydroxyapatite scaffold (CHAS) and filtered bone marrow aspirate (fBMA) for the treatment of KJSLs and (2) identify significant predictors of the treatment outcomes. Study Design: Case series; Level of evidence, 4. Methods: All patients who underwent surgery because of a KJSL (size ≥1.5 cm2; International Cartilage Regeneration & Joint Preservation Society grades 3-4) using the combination above were selected from a hospital registry database (100 patients; minimum 2-year follow-up). Patient characteristics, medical history, knee joint and lesion status, intraoperative details, and cellular parameters of the injected fBMA were collected. The arthroscopic evaluation of chondral and meniscal tissue quality in all knee compartments was performed using the Chondropenia Severity Score. Treatment outcomes were determined clinically using patient-reported outcome measures (Knee Injury and Osteoarthritis Outcome Score, EuroQol–5 Dimensions–3 Levels, EuroQol–Visual Analog Scale, and Tegner Activity Scale) and by assessing the occurrence of serious adverse events and graft failure. Multivariable regression analysis was performed to identify significant predictors of the treatment outcomes. Results: At a mean follow-up of 54.2 ± 19.4 months, 78 (87%) patients completed the questionnaires with significant improvements toward the baseline (P < .00625): KOOS Pain subscale from 62 ± 17 to 79 ± 18, KOOS Total score from 57 ± 16 to 70 ± 20, EuroQol–Visual Analog Scale from 61 ± 21 to 76 ± 16, EuroQol–5 Dimensions–3 Levels from 0.57 ± 0.20 to 0.80 ± 0.21, and Tegner Activity Scale from 2.8 ± 1.5 to 3.9 ± 1.9. The graft failure rate was 4%. A longer duration of preoperative symptoms, previous surgery, larger lesions, older age, and female sex were the main negative predictors for the treatment outcomes. The Chondropenia Severity Score and the number of fibroblast colony-forming units in fBMA positively influenced some of the clinical results and safety. Conclusion: A CHAS augmented with fBMA proved to be an adequate and safe approach for the treatment of KJSLs up to midterm follow-up. Based on the subanalysis of predictive factors, the surgical intervention should be performed in a timely and precise manner to prevent lesion enlargement, deterioration of the general knee cartilage status, and recurrent surgical procedures, especially in older and female patients. When a CHAS is used, the quantity of MSCs seems to play a role in augmentation. Registration: NCT06078072 (ClinicalTrials.gov identifier).

Frozen inactivated autograft replantation for bone and soft tissue sarcomas.

The frozen inactivation of autologous tumor bones using liquid nitrogen is an important surgical method for limb salvage in patients with sarcoma. At present, there are few research reports related to frozen inactivated autograft replantation. In this study, we retrospectively collected the clinical data of patients with bone and soft tissue sarcoma treated with liquid nitrogen-frozen inactivated tumor bone replantation, and analyzed the safety and efficacy of this surgical method. The healing status of the frozen inactivated autografts was evaluated using the International Society of Limb Salvage (ISOLS) scoring system. Functional status of patients was assessed using the Musculoskeletal Tumor Society (MSTS) scale. This study included 43 patients. The average length of the bone defect after tumor resection is 16.9cm (range 6.3-35.3 cm). Patients with autograft not including the knee joint surface had significantly better healing outcomes (ISOLS scores) (80.6% ± 15% vs 28.2% ± 4.9%, P<0.001) and limb function (MSTS score) (87% ± 11.6% vs 27.2% ± 4.4%, P<0.001) than patients with autografts including the knee joint surface. The healing time of the end of inactivated autografts near the metaphyseal was significantly shorter than that of the end far away from the metaphyseal (9.8 ± 6.3 months vs 14.9 ± 6.3 months, P=0.0149). One patient had local recurrence, one had an autograft infection, five (all of whom had an autograft including the knee joint surface) had joint deformities, and seven had bone non-union. Frozen inactivated autologous tumor bone replantation is safe and results in good bone healing. But this method is not suitable for patients with autograft involving the knee joint surface.

Morphohistological study of regeneration of knee joint cartilage defects in an experimental model under the influence of nuclear magnetic resonance therapy

Despite the variety of modern methods of treatment, the problem of hyaline cartilage regeneration is still relevant. Purpose of the study: to determine the effect of nuclear magnetic resonance therapy on the regenerative ability of simulated defects in the cartilage tissue of the knee joint in rats, to assess the dynamics of microscopic changes in articular cartilage in the main and control groups. The study was performed on 60 sex-mature rats. The defects were created in the area of the articular surfaces of the left knee joint – 30 defects in the main group and 30 defects in the control group. The right knee joint of both study groups was used as the norm. Medical (antibiotics, anti-inflammatory, analgesic) therapy was carried out for 3 days after the surgery. On the 4th day after surgery, rats of the main group were given nuclear magnetic resonance therapy for 60 minutes, for 7 days. After 7, 14, 21, 28 days after therapy, histological analysis of cartilage regenerate was performed. 28 days after the use of nuclear magnetic resonance therapy, the height of cartilage regenerate in rats was 82.12±8.89 μm in the intervention group and 56.34±7.82 μm in the control group. Cartilage regenerate in rats after nuclear magnetic resonance therapy was close to the structure of intact hyaline cartilage. However, complete regeneration did not occur, as evidenced by the smaller thickness of the articular cartilage compared to that in the right knee joint. In the control group, the formation of the regeneration had pronounced signs of dysregeneration. The cartilage tissue in the area of the defect, was predominantly fibrous in the nature with areas of necrosis. Nuclear magnetic resonance therapy contributes to the formation of articular cartilage in the defect – cartilage regenerate, which in its histological structure approaches hyaline cartilage.

Research on Digital Manufacturing Technology of Key Components of Artificial Knee Joint

The surface of the artificial knee joint manufactured by 3D printing technology is rough. This study uses advanced multi-axis machining technology to study how to improve the manufacturing accuracy of the artificial knee joint surface, and uses five-axis machining CAM software to analyze the process of three-dimensional model of the artificial knee joint and to compile tool path, create a five-axis special post-processor, convert the tool path point file into the NC program for machine tool processing. In order to ensure the safety and efficiency of the processing procedure, a Mikron HEM-500U machine tool simulation platform was built in the VERICUT simulation system for simulation processing verification, and then the blank prototype obtained by 3D printing was processed in a five-axis machine tool to meet medical clinical use requirements.

In Knee-Joint Surface Lesions, an Aragonite-Based Scaffold Improved Clinical and Radiographic Outcomes at 24 Months Versus Microfracture and Debridement.

In Knee-Joint Surface Lesions, an Aragonite-Based Scaffold Improved Clinical and Radiographic Outcomes at 24 Months Versus Microfracture and Debridement.

Numerical and Experimental Investigation on the Abrasive Flow Machining of Artificial Knee Joint Surface

The titanium alloy artificial knee joint is used extensively in the current medical industry due to its distinct characteristics and properties that are like the real human knee joint, but it does need to be polished to improve its performance and service life before it can be used. Due to the complicated surface profile, the traditional abrasive flow machining technique cannot achieve a good surface finish offering uniformity and quality. Thus, in this paper, a proper constrained flow channel is designed to conduct the abrasive flow machining of the titanium alloy artificial knee joint surface to overcome these issues. A numerical study is first conducted to explore the distribution of abrasive flow velocity and pressure near the target surface in the constrained flow channel by using the COMSOL Multiphysics software, and it is found from the distribution of the dimensionless material removal rate on the target surface that the exchange of the abrasive flow inlet and outlet during the machining process is recommended to improve the surface finish uniformity. Then, the corresponding experiments are conducted to analyze the surface morphology before and after the abrasive flow machining process. It is found that the surface roughness of the target surface decreases from approximately 394 nm to 171 nm with good uniformity as well. Therefore, the proposed abrasive flow machining method with a properly designed constrained flow channel is useful for the rough polishing and fine finishing of the titanium alloy artificial joint.

Intra- and interobserver reliability analysis of pediatric lower limb parameters on digital long leg radiographs

BackgroundMalalignments of the lower extremity are common reasons for orthopedic consultation because it may lead to osteoarthritis in adulthood. An accurate and reliable radiological assessment of lower limb alignment in children and adolescents is essential for clinical decision-making on treatment of limb deformities and for regular control after a surgical intervention.ObjectiveFirst, does the analysis of full-length standing anteroposterior radiographs show a good intra- and interobserver reliability? Second, which parameter is most susceptible to observer-dependent errors? Third, what is the Standard Error of Measurement (SEM95%) of the absolute femoral and tibial length?MethodsTwo observers evaluated digital radiographs of 144 legs from 36 children and adolescents with pathological valgus alignment before a temporary hemiepiphysiodesis and before implant removal. Parameters included Mechanical Femorotibial Angle (MFA), Mechanical Axis Deviation (MAD), mechanical Lateral Distal Femoral Angle (mLDFA), mechanical Medial Proximal Tibial Angle (mMPTA), mechanical Lateral Proximal Femoral Angle (mLPFA), mechanical Lateral Distal Tibial Angle (mLDTA), Joint Line Convergence Angle (JLCA), femur length, tibial length. Intra- and interobserver reliability (ICC2,1), SEM95% and proportional errors were calculated.ResultsThe intra- and interobserver reliability for almost all measurements was found to be good to excellent (Intra-ICC2,1: 0.849–0.999; Inter-ICC2,1: 0.864–0.996). The SEM95% of both observers was found to be ± 1.39° (MFA), ± 3.31 mm (MAD), ± 1.06° (mLDFA) and ± 1.29° (mMPTA). The proportional error of MAD and MFA is comparable (47.29% vs. 46.33%). The relevant knee joint surface angles show a lower proportional error for mLDFA (42.40%) than for mMPTA (51.60%). JLCA has a proportional error of 138%. Furthermore, the SEM95% for the absolute values of the femoral and tibial length was 4.53 mm for the femur and 3.12 mm for the tibia.ConclusionsIn conclusion, a precise malalignment measurement and the knowledge about SEM95% of the respective parameters are crucial for correct surgical or nonsurgical treatment. The susceptibility to error must be considered when interpreting malalignment analysis and must be considered when planning a surgical intervention. The results of the present study elucidate that MAD and MFA are equally susceptible to observer-dependent errors. This study shows good to excellent intra- and interobserver ICCs for all leg alignment parameters and joint surface angles, except for JLCA.Trial registration: This study was registered with DRKS (German Clinical Trials Register) under the number DRKS00015053.Level of evidenceI, Diagnostic Study.

Tribological behavior of CoCrMo artificial knee joint with symmetrically biomimetic textured surfaces on PEEK

CoCrMo alloys are extensively used in the field of artificial knee joints. However, wear performance is one of the most important problems of artificial knee joints, limiting service life. In this paper, symmetrically biomimetic textures with the spacing of 200 μm, the width of 45 μm, and the depth of 45 μm are fabricated on the surfaces of CoCrMo artificial knee joints to improve its tribological properties. Friction tests are conducted under the following conditions: frequency 1.5 Hz, sliding time 30 min, load (5 ∼ 15 N), lubricant concentration (15 ∼ 55 mg/ml). Results show that textures, lubricating condition, load and surface wettability have significant influence of friction properties, and textured CoCrMo artificial knee joints show the better friction performances compared STT-0, and samples with scaly textured structure (STT-3) own best friction performances with the lowest coefficients of friction. The responsible mechanisms on the enhancement of friction properties of textured joint are explained as follows: micro-texture plays the role of storing the wear debris and lubricating fluid, preventing the wear debris from entering between the friction pairs and forming hydrodynamic pressure to generate hydrodynamic lubrication effect. Derivative-cutting behavior of the lower edge of biomimetic textures can act as “another cutting tool” to remove the wear debris which adhered on the bottom of the PEEK balls.

Effects of Relative Inertial Load on Quadriceps Electromyography during Maximal Effort Flywheel-based Iso-Inertial Training (FIT) Squats

The effects of inertial load on quadriceps electromyography (EMG) during flywheel-based iso-inertial training (FIT) squats is unclear. Healthy, resistance-trained males (n=8) and females (n=8) completed five sets of five maximal-effort squats with varying inertial loads in a randomized order. Sagittal plane knee joint angles and surface EMG activity of the vastus lateralis (VL) were measured. Average knee angular velocity, but not peak knee flexion or total excursion, decreased during both the concentric and eccentric phases with increasing inertial load (p&lt;0.001) in both sexes. Integrated EMG (iEMG) activity increased with increasing inertial load for all muscles (p&lt;0.001). VL iEMG and peak amplitude were significantly greater in females. However, peak EMG amplitude was not significantly different among inertial loads for either sex. Mean EMG amplitude during the concentric phase and eccentric phases of the VL tended to be greater in females. Increasing relative inertial load increases quadriceps iEMG activity due to greater exercise duration, but has minimal effects on EMG amplitude.

Z-Plasty with Skin Grafting for Post-Burn Contracture - Study of 30 Cases

Introduction: Postburn contracture is a very common problem in case of undertreated and neglected cases of burns involving the flexor surface of joints of limbs. Satisfactory treatment of postburn contracture needs surgical excision of scar followed by Z-plasty. In case of a severe contracture of joints, Z-plasty is combined with skin grafting for the tension-free treatment of post-burn contracture. Methods: The study was conducted in Sadar Hospital, Sunamgonj and several private clinics in selected districts during the period from 2008 to 2020. Thirty (30) patients with contractures involving flexor surface of Elbow, Knee, and Metacarpophalangeal joints of hands of mild to severe degrees and various durations were treated with Z-plasty plus Split thickness Skin grafts. The operated limbs were immobilized with POP casts. Perioperative Parenteral Antibiotics were prescribed along with adequate Analgesics, Autiulcerants and vitamins, and proper nutrition. Both the operative sites (Recipient and donor areas) were examined by check dressing after the 7th to 14th postoperative days. Result: 5 and 12 patients had complications like infection, flap tip necrosis, and recurrent contractures respectively. But overall results were satisfactory in terms of joint extension, mobility, cosmetic appearance, and patient satisfaction. Very naturally in case of severe contractures, full correction was not possible by single-stage operation. Conclusion: Tension-free flap must be used in patients with mild to severe contractures. Combining skin Grafting with Z-plasty is easy and has better results than Z-plasty alone. It is recommended in patients of Z-plasty with intraoperative flap tension.

Estrogen alleviates post-traumatic osteoarthritis progression and decreases p-EGFR levels in female mouse cartilage

ObjectiveTo investigate the effect of estrogen on the progression of post-traumatic osteoarthritis (PTOA) in mice and its possible mechanism.MethodsTwelve-week-old ICR mice were divided into Group A (female control group), group B (ovariectomized(OVX) group), group C (OVX group supplemented with estrogen), and group D (male group) by destabilization of the medial meniscus (DMM)or sham operation. Safranin O staining was performed at 8 weeks and 12 weeks after operation, and the degree of articular cartilage lesion was evaluated using Mankin score. Twelve weeks after the operation, tissue sections were stained to analyze the matrix metalloproteinase 13(MMP13), phosphorylated epidermal growth factor receptor (p-EGFR) expression and apoptosis of chondrocytes.ResultsDecreased estrogen can significantly increase the weight of mice in female mice. The degree of cartilage damage in the knee joint on the DMM side of female mice was significantly severer than that on the Sham side. The DMM side also showed higher MMP13 expression and increased apoptotic chondrocytes. The degree of cartilage damage in the knee joint on the DMM side of female mice was significantly reduced after estrogen supplementation, and cartilage damage in the knee joint on the DMM side of female mice was less serious than that of male mice. As estrogen levels decreased, the severity of cartilage erosion in the knee joint on the DMM side was aggravated, and p-EGFR expression in the cartilage surface was also higher in female mice contrast to that in male mice. However, minimal changes in p-EGFR expression in the cartilage surface of bilateral knee joints of male mice were observe.ConclusionEstrogen has a regulatory effect on PTOA and its inhibits the expression of p-EGFR in cartilage on the knee joint surface and has a protective effect on articular cartilage in female mice.

Quadriceps electromyography during flywheel-based inertial training (FIT) and dynamic constant external resistance (DCER) squats at similar tempo

ABSTRACT Flywheel-based iso-inertial training (FIT) has been purported to provide enhanced adaptations to muscle overload compared to dynamic constant external resistance (DCER), but previous studies have not controlled for exercise intensity. We compared quadriceps electromyography (EMG) amplitude between FIT- and DCER-squats with similar tempo. Eleven (5 M and 6F) resistance-trained participants completed sets of five maximal velocity FIT (0.025 kg∙m2) and DCER (55 ± 15 %1RM) squats. Sagittal plane knee joint angles and surface EMG activity of the vastus lateralis (VL), vastus medialis (VM) and rectus femoris (RF) were measured. Repetition time and peak knee angles were similar between FIT and DCER squats. Mean knee angular velocity during the concentric (122.2 ± 23.6 vs. 108.9 ± 22.9, p = 0.022, Cohen’s D: 0.820), but not eccentric, phase was significantly greater during FIT. Peak VM (210.4 ± 49.3 vs. 177.5 ± 56.3 %MVIC, p = 0.001; Cohen’s D: 1.416), but not VL or RF, EMG amplitude was significantly greater in FIT compared to DCER. Mean EMG amplitude was significantly (p < 0.001) greater during the concentric than the eccentric phase for the VL and VM but not RF. Mean EMG amplitude was not significantly different between modes during either the concentric or eccentric phase. Quadriceps EMG amplitude is largely similar between FIT and DCER squats when matched for movement velocity.

Knee Joint Menisci Are Shock Absorbers: A Biomechanical In-Vitro Study on Porcine Stifle Joints

The aim of this biomechanical in vitro study was to answer the question whether the meniscus acts as a shock absorber in the knee joint or not. The soft tissue of fourteen porcine knee joints was removed, leaving the capsuloligamentous structures intact. The joints were mounted in 45° neutral knee flexion in a previously validated droptower setup. Six joints were exposed to an impact load of 3.54 J, and the resultant loss factor (η) was calculated. Then, the setup was modified to allow sinusoidal loading under dynamic mechanical analysis (DMA) conditions. The remaining eight knee joints were exposed to 10 frequencies ranging from 0.1 to 5 Hz at a static load of 1210 N and a superimposed sinusoidal load of 910 N (2.12 times body weight). Forces (F) and deformation (l) were continuously recorded, and the loss factor (tan δ) was calculated. For both experiments, four meniscus states (intact, medial posterior root avulsion, medial meniscectomy, and total lateral and medial meniscectomy) were investigated. During the droptower experiments, the intact state indicated a loss factor of η = 0.1. Except for the root avulsion state (−15%, p = 0.12), the loss factor decreased (p < 0.046) up to 68% for the total meniscectomy state (p = 0.028) when compared to the intact state. Sinusoidal DMA testing revealed that knees with an intact meniscus had the highest loss factors, ranging from 0.10 to 0.15. Any surgical manipulation lowered the damping ability: Medial meniscectomy resulted in a reduction of 24%, while the resection of both menisci lowered tan δ by 18% compared to the intact state. This biomechanical in vitro study indicates that the shock-absorbing ability of a knee joint is lower when meniscal tissue is resected. In other words, the meniscus contributes to the shock absorption of the knee joint not only during impact loads, but also during sinusoidal loads. The findings may have an impact on the rehabilitation of young, meniscectomized patients who want to return to sports. Consequently, such patients are exposed to critical loads on the articular cartilage, especially when performing sports with recurring impact loads transmitted through the knee joint surfaces.

The Assessment of the Condition of Knee Joint Surfaces with Acoustic Emission Analysis.

The knee joint, being the largest joint in the human body, is responsible for a great percentage of leg movements. The diagnosis of the state of knee joints is usually based on X-ray scan, ultrasound imaging, computerized tomography (CT), magnetic resonance imaging (MRI), or arthroscopy. In this study, we aimed to create an inexpensive, portable device for recording the sound produced by the knee joint, and a dedicated application for its analysis. During the study, we examined fourteen volunteers of different ages, including those who had a knee injury. The device effectively enables the recording of the sounds produced by the knee joint, and the spectral analysis used in the application proved its reliability in evaluating the knee joint condition.

Osteoarthritis-Related Degeneration Alters the Biomechanical Properties of Human Menisci Before the Articular Cartilage.

An exact understanding of the interplay between the articulating tissues of the knee joint in relation to the osteoarthritis (OA)-related degeneration process is of considerable interest. Therefore, the aim of the present study was to characterize the biomechanical properties of mildly and severely degenerated human knee joints, including their menisci and tibial and femoral articular cartilage (AC) surfaces. A spatial biomechanical mapping of the articulating knee joint surfaces of 12 mildly and 12 severely degenerated human cadaveric knee joints was assessed using a multiaxial mechanical testing machine. To do so, indentation stress relaxation tests were combined with thickness and water content measurements at the lateral and medial menisci and the AC of the tibial plateau and femoral condyles to calculate the instantaneous modulus (IM), relaxation modulus, relaxation percentage, maximum applied force during the indentation, and the water content. With progressing joint degeneration, we found an increase in the lateral and the medial meniscal instantaneous moduli (p < 0.02), relaxation moduli (p < 0.01), and maximum applied forces (p < 0.01), while for the underlying tibial AC, the IM (p = 0.01) and maximum applied force (p < 0.01) decreased only at the medial compartment. Degeneration had no influence on the relaxation percentage of the soft tissues. While the water content of the menisci did not change with progressing degeneration, the severely degenerated tibial AC contained more water (p < 0.04) compared to the mildly degenerated tibial cartilage. The results of this study indicate that degeneration-related (bio-)mechanical changes seem likely to be first detectable in the menisci before the articular knee joint cartilage is affected. Should these findings be further reinforced by structural and imaging analyses, the treatment and diagnostic paradigms of OA might be modified, focusing on the early detection of meniscal degeneration and its respective treatment, with the final aim to delay osteoarthritis onset.