Kinetics Of Reduction Reaction Research Articles

Steering the Orbital Hybridization to Boost the Redox Kinetics for Efficient Li-CO2 Batteries.

The sluggish CO2 reduction and evolution reaction kinetics are thorny problems for developing high-performance Li-CO2 batteries. For the complicated multiphase reactions and multielectron transfer processes in Li-CO2 batteries, exploring efficient cathode catalysts and understanding the interplay between structure and activity are crucial to couple with these pendent challenges. In this work, we applied the CoS as a model catalyst and adjusted its electronic structure by introducing sulfur vacancies to optimize the d-band and p-band centers, which steer the orbital hybridization and boost the redox kinetics between Li and CO2, thus improving the discharge platform of Li-CO2 batteries and altering the deposition behavior of discharge products. As a result, a highly efficient bidirectional catalyst exhibits an ultrasmall overpotential of 0.62 V and a high energy efficiency of 82.8% and circulates stably for nearly 600 h. Meanwhile, density functional theory calculations and multiphysics simulations further elucidate the mechanism of bidirectional activity. This work not only provides a proof of concept to design a remarkably efficient catalyst but also sheds light on promoting the reversible Li-CO2 reaction by tailoring the electronic structure.

P-band regulation guides the free-standing porous carbon electrode for efficient Na-CO2 batteries

The Na-CO2 batteries with low-cost resources and high energy density have attracted huge attention in Mars and deep ocean exploration, but the slow CO2 reduction reaction (CO2RR) and CO2 evolution reaction (CO2ER) kinetics severely limit their practical application. Developing free-standing cathodes and understanding the relationship between the catalyst's active center and activity are essential to address long-standing challenges. This manuscript explores the promising metal-free porous carbon as a catalyst. The porous carbon network vertically grows on the surface of free-standing carbon paper to maximum exposure to the active site and optimization of electron/electrolyte transfer. Moreover, the active center of the carbon catalyst is optimized by introducing nitrogen or sulfur hetero-atom to regulate the p-band center, which steers the orbital hybridization and accelerates CO2RR and CO2ER kinetics The p-band optimized free-standing porous carbon electrode shows outstanding cycling of 1000 h with a small voltage gap of 1.04 V and a large energy efficiency of 71.2 % at 10 uA cm−2. This study provides a new strategy for designing and fabricating p-band guided free-standing electrodes aiming at high-performance and wearable Na-CO2 batteries.

A perovskite-fluorite dual-phase cathode for boosting oxygen reduction reaction in NH3-Fueled solid oxide fuel cells

Ammonia (NH3), a promising carbon-free energy carrier, can be directly and efficiently converted into electricity in solid oxide fuel cells (SOFCs). However, the NH3-fueled SOFC (NH3–SOFC) still suffered from several difficulties, including sluggish oxygen reduction reaction (ORR) kinetics and poor cathode durability. In this study, we develop a LSCF-GDC dual-phase cathode with uniform distribution for NH3–SOFC. In comparison with commercial counterpart, the dual-phase cathode shows a lower ORR resistance of 0.114 Ω cm2 for at 700 °C due to reduced grain sizes and expanded triple-phase boundary (TPB) length. The resultant NH3–SOFC follows the H2 oxidation process and delivers a comparable peak power density of 0.347 Wcm−2 to H2–SOFC at 700 °C, which is further improved to 0.516 Wcm−2 after 280 h activation at 0.7 V. Further operation of five thermal cycles between 700 and 500 °C results in a performance degradation, which can be explained by the microstructure changes of Ni-based anode rather than the dual-phase cathode. Moreover, the thermal cycled NH3–SOFC can maintain stable operation without current decay at constant 700 °C and 0.7 V in the subsequent 135 h, further demonstrating the robustness of the dual-phase cathode. Therefore, the introduction of GDC into self-assembled dual-phase cathode is an effective way to synergistically promote the electrochemical activity and durability of the cathode for NH3–SOFC.

Cu Regulating the Bifunctional Activity of Co-O Sites for the High-Performance Rechargeable Zinc-Air Battery.

The rational design of cost-effective and highly active electrocatalysts becomes the crucial energy storage technology to boost the kinetics of the oxygen reduction reaction (ORR) and the oxygen evolution reaction (OER), which hinders the large-scale application of metal-air batteries under the situation of increasingly pressing energy anxiety. Herein, the Co-based ZIF introduced the moderate amount of Cu2+-derived Cu/Co metal nanoparticles (NPs) embedded in carbon frameworks after high-temperature calcination. The Co-O bond on the surface of Co nanoparticles is modulated by adjacent Cu nanoparticles with the surface Cu-O bonds. The resulted increase of the Co2+/Co3+ ratio in 0.1CuCo-NC enhances the ORR/OER bifunctional catalytic kinetics along with the ΔE of 0.639 V. In situ Raman spectra of the catalyst on the three-electrode system as well as in the driven zinc-air battery (ZAB) show that the Co-O active sites regulated by Cu nanoparticles with Cu-O bonds maintain a periodic lattice expansion and compression during discharging and charging. The zinc-air battery based on 0.1CuCo-NC has a peak power density of up to 198.3 mW cm-2, a mass-specific capacity of 798.2 mAh g-1, and a cycling stability of 923 h at room temperature. This work makes up the research gap of a Co-based metal-organic framework (MOF)-derived catalyst regulated by a transition metal.

Valence electronic structure on oxygen reduction reaction kinetics of Cu-doped Ba0.5Sr0.5FeO3−δ for IT-SOFCs

Ba0.5Sr0.5Fe1-xCuxO3-δ (BSFCx, x = 0–0.2) cathodes were investigated in the relationship between electronic structure and oxygen reduction reaction (ORR) kinetics. Electronic structure analysis revealed that Cu doping increased the oxygen vacancies (δ) from 0.384 (BSF) to 0.638 (BSFC0.2). The valence band maximum (VBM) shifted from 0.68 eV (BSF) to 0.24 eV (BSFC0.2), which implies a lower activation energy for charge transfer to the adsorbed oxygen. The area specific resistance was 0.042 Ω cm2 at 700 °C (BSFC0.2), a reduction of more than 50 % compared to 0.086 Ω cm2 (BSF). For the distribution of relaxation times analysis, BSFC0.2 showed the smallest peak area in medium frequency region, where the charge exchange and ion transfer occur at cathode.

Three-dimensional porous structured cobalt- and nitrogen-doped carbon nanotube electrocatalyst derived from cobalt-based zeolitic imidazolate framework nanoleaves for high performance zinc-air battery

The development of efficient and cost-effective electrocatalysts to overcome the intrinsic sluggish kinetics of the oxygen reduction reaction (ORR) in zinc-air batteries is crucial. In this study, we introduce a strategy that integrates a template-assisted synthesis with subsequent thermal treatment to fabricate an active and stable cobalt-based nitrogen-doped carbon electrocatalyst, denoted as Co-N-CNT. The strategy adjusts the disordered architecture of the zeolitic imidazolate framework (ZIF) through the synergistic effect of bimetallic species, restricted the growth of zeolitic imidazolate framework nanoleaves (ZIF-L) using salt templates, and directed the transformation from a two-dimensional blade-like morphology to a three-dimensional multi-tiered composite structure. Notably, the Co-N-CNT-800 sample, synthesized at an optimized pyrolysis temperature of 800 °C, exhibits a half-wave potential of 0.89 V and demonstrates stability with sustained cycling over 21 h, which is comparable to the performance of commercial Pt/C electrocatalysts. Moreover, when employed as the cathode in zinc-air batteries, Co-N-CNT-800 not only surpasses Pt/C in terms of power density but also exhibits long-term charge/discharge stability. This findings offer a viable pathway for the design of active and cost-effective ORR electrocatalysts, holding promise for applications in the electrochemical energy storage and conversion systems.

MOF-on-MOF-derived FeCo@NC OER&ORR bifunctional electrocatalysts for zinc-air batteries

Zinc-air batteries, as one of the emerging areas of interest in the quest for sustainable energy solutions, are hampered by the intrinsically sluggish kinetics of the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER), and still suffer from the issues of low energy density. Herein, we report a MOF-on-MOF-derived electrocatalyst, FeCo@NC-II, designed to efficiently catalyze both ORR (Ehalf = 0.907 V) and OER (Ej=10 = 1.551 V) within alkaline environments, surpassing esteemed noble metal benchmarks (Pt/C and RuO2). Systematically characterizations and density functional theory (DFT) calculations reveal that the synergistic effect of iron and cobalt bimetallic and the optimized distribution of nitrogen configuration improved the charge distribution of the catalysts, which in turn optimized the adsorption / desorption of oxygenated intermediates accelerating the reaction kinetics. While the unique leaf-like core–shell morphology and excellent pore structure of the FeCo@NC-II catalyst caused the improvement of mass transfer efficiency, electrical conductivity and stability. The core and shell of the precursor constructed through the MOF-on-MOF strategy achieved the effect of 1 + 1 > 2 in mutual cooperation. Further application to zinc-air batteries (ZABs) yielded remarkable power density (212.4 mW/cm2), long cycle (more than 150 h) stability and superior energy density (∼1060 Wh/kg Zn). This work provides a methodology and an idea for the design, synthesis and optimization of advanced bifunctional electrocatalysts.

Cu into Cu2O/RuAl intermetallic heterojunction for lowering the thermodynamic energy barrier of the CO2 reduction and evolution reactions in Li–CO2 battery

The Li–CO2 battery has been under the spotlight of future battery technologies since it can achieve CO2 utilization and energy conversion simultaneously. However, its advancement is hampered by poor energy efficiency and limited reversibility due to the sluggish kinetics of the CO2 reduction and evolution reactions. Herein, a multiscale nanoporous interpenetrating‑phase nanohybrid of RuAl intermetallic and Cu2O (MP-Cu2O/RuAl) was carved by driving synchronous phase and microstructure evolutions through dealloying of one RuCuAl master alloy. The built-in RuAl intermetallic and Cu2O closely stack to form abundant nano-interfaces with revolutionized electronic structure. The theoretical simulations reveal that the Cu2O/RuAl interface can distinctly reduce the energy barrier of the Li2CO3 decomposition reaction. The interconnected pore channels with large surface area can enhance catalytic site accessibility, mass transfer, and uniform deposition of the discharge products. In situ differential electrochemical mass spectrometry discloses that the CO2-to-electron ratio during charging coincides with the theoretical value of 3/4, demonstrating the high efficacy of MP-Cu2O/RuAl in achieving the recycling of CO2. The dealloying protocol provides an affordable platform to empower transition metal oxides into high-efficiency electrocatalysts by hybridizing with metallic nano-sponge for advancing the application of Li–CO2 batteries.

FeMnO3/CNT as a synergistic bifunctional electrocatalyst for oxygen reduction and oxygen evolution reactions in alkaline medium

The development of highly effective and low-cost electrocatalysts for energy conversion and storage devices is triggered by the sluggish kinetics of oxygen reduction and evolution reactions. Perovskite-based oxides are identified as potential ORR and OER electrocatalysts in an alkaline medium. Thus, the present study discusses the synthesis and characterization of FeMnO3/CNT as a bifunctional catalyst with a low potential gap of 0.89 V. The FeMnO3/CNT composite was synthesized by the solution combustion method and characterized using spectroscopic and electron microscopic techniques. The increase in the ID/IG ratio obtained from the Raman spectra of the FeMnO3/CNT composite with respect to bare CNT indicates the functionalization of CNT. The ORR and OER characteristics of the FeMnO3/CNT composite were analyzed with rotating ring disc electrode and rotating disc electrode measurements. The LSV curve of the FeMnO3/CNT composite synthesized with 0.3g of CNT show better ORR and OER activity. The ORR activity measurements of the composite done in 0.1 M KOH electrolyte show a good onset potential of 0.95 V vs. RHE and a half-wave potential of 0.74 V. The HPRR studies show that the ORR reaction mechanism follows a 2e− + 2e− reduction pathway. The OER measurements in an alkaline medium show an onset potential of 1.63 V vs. RHE with a Tafel slope of 115.3 mV dec−1. Also, this work gives an insight into the fundamental understanding of the synergy between the perovskite and CNT, leading to an enhanced ORR and OER catalytic activity. In addition, the material exhibits good stability for ORR and OER stability studies.

Enhanced Oxygen Accumulation for a Hydrophobic Cathode in Lean-Oxygen Seawater Batteries.

The unsatisfactory oxygen reduction reaction (ORR) kinetics caused by the inherent lean-oxygen marine environment brings low power density for metal-dissolved oxygen seawater batteries (SWBs). In this study, we propose a seawater/electrode interfacial engineering strategy by constructing a hydrophobic coating to realize enhanced mass transfer of dissolved oxygen for the fully immersed cathode of SWBs. Accumulation of dissolved oxygen from seawater to the catalyst is particularly beneficial for improving the ORR performance under lean-oxygen conditions. As a result, SWB assembled with a hydrophobic cathode achieved a power density of up to 2.32 mW cm-2 and sustained discharge at 1.3 V for 250 h. Remarkably, even in environments with an oxygen concentration of 4 mg L-1, it can operate at a voltage approximately 100 mV higher than that of an unmodified SWB. The introduction of a hydrophobic interface enhances the discharge voltage and power of SWBs by improving interfacial oxygen mass transfer, providing new insights into improving the underwater ORR performance for practical SWBs.

Phosphorus-Doping Enables the Superior Durability of a Palladium Electrocatalyst towards Alkaline Oxygen Reduction Reactions.

The sluggish kinetics of oxygen reduction reactions (ORRs) require considerable Pd in the cathode, hindering the widespread of alkaline fuel cells (AFCs). By alloying Pd with transition metals, the oxygen reduction reaction's catalytic properties can be substantially enhanced. Nevertheless, the utilization of Pd-transition metal alloys in fuel cells is significantly constrained by their inadequate long-term durability due to the propensity of transition metals to leach. In this study, a nonmetallic doping strategy was devised and implemented to produce a Pd catalyst doped with P that exhibited exceptional durability towards ORRs. Pd3P0.95 with an average size of 6.41 nm was synthesized by the heat-treatment phosphorization of Pd nanoparticles followed by acid etching. After P-doping, the size of the Pd nanoparticles increased from 5.37 nm to 6.41 nm, and the initial mass activity (MA) of Pd3P0.95/NC reached 0.175 A mgPd-1 at 0.9 V, slightly lower than that of Pd/C. However, after 40,000 cycles of accelerated durability testing, instead of decreasing, the MA of Pd3P0.95/NC increased by 6.3% while the MA loss of Pd/C was 38.3%. The durability was primarily ascribed to the electronic structure effect and the aggregation resistance of the Pd nanoparticles. This research also establishes a foundation for the development of Pd-based ORR catalysts and offers a direction for the future advancement of catalysts designed for practical applications in AFCs.

Synergistic Bulk and Surface Engineering for Expeditious and Durable Reversible Protonic Ceramic Electrochemical Cells Air Electrode.

Reversible protonic ceramic electrochemical cells (R-PCECs) offer the potential for high-efficiency power generation and green hydrogen production at intermediate temperatures. However, the commercial viability of R-PCECs is hampered by the sluggish kinetics of the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) within conventional air electrodes operating at reduced temperatures. To address this challenge, this work introduces a novel approach based on the simultaneous optimization of bulk-phase metal-oxygen bonds and in-situ formation of a metal oxide nano-catalyst surface modification. This strategy is designed to expedite the ORR/OER electrocatalytic activity of air electrodes exhibiting triple (O2-, H+, e-) conductivity. Specifically, this engineered air electrode nanocomposite-Ba(Co0.4Fe0.4Zr0.1Y0.1)0.95Ni0.05F0.1O2.9-δ demonstrates remarkable ORR/OER catalytic activity and exceptional durability in R-PCECs. This is evidenced by significantly improved peak power density from 626 to 996mW cm-2 and highly stable reversibility over a 100-h cycling period. This research offers a rational design strategy to achieve high-performance R-PCEC air electrodes with superior operational activity and stability for efficient and sustainable energy conversion and storage.

Bimetallic-doped three-dimensional carbon skeleton porous material as efficient catalysts for oxygen reduction reaction

The slowness of the oxygen reduction reaction (ORR) kinetics of the fuel cell cathode has terrifically inhibited its development process. Now it is of considerable importance to research low-cost, multi-defect, high-performance non-noble metal ORR catalysts. Specifically, CuO nanosheets are grown in situ on ZIF-8 to form a composite material (zif-8@CuO), and then undergo a high-temperature carbonization process. Finally, the Zn-Cu codoped composite material Zn-xCu-N/C with a porous structure supported by a three-dimensional carbon skeleton can be obtained. The material has a 3D carbon skeleton support and a rich pore structure, which can expose more active sites. The combination of bimetallic Zn and Cu with carbon materials also increases the overall stability and conductivity of the material, which is beneficial to improvement of catalytic performance. The electrochemical performance test results show that the onset potential and half-wave potential of the Zn-0.1Cu-N/C material are 0.889 V and 0.803 V respectively, with a low Tafel slope of 62 mV dec−1 and excellent long-term stability. After 10000 cycles, the ORR curve only changed 18 mV, while the carbon skeleton can still maintain unchanged.

Crystalline CdS/Amorphous Cd(OH)2 Composite for Electrochemical CO2 Reduction to CO in a Wide Potential Window.

Electrochemical CO2 reduction is a promising method for converting atmospheric CO2 into valuable low-carbon chemicals. In this study, a crystalline cadmium sulfide/amorphous cadmium hydroxide composite was successfully deposited on the carbon paper substrate surface by in-situ chemical bath deposition (named as c-CdS/a-Cd(OH)2/CP electrodes) for the efficient electrochemical CO2 reduction to produce CO. The c-CdS/a-Cd(OH)2/CP electrode exhibited high CO Faradaic efficiencies (>90 %) under a wide potential window of 1.0 V, with the highest value reaching ~100 % at the applied potential ranging from -2.16 V to -2.46 V vs. ferrocene/ferrocenium (Fc/Fc+), superior to the crystalline counterpart c-CdS/CP and c-CdS/c-Cd(OH)2@CP electrodes. Meanwhile, the CO partial current density reached up to 154.7 mA cm-2 at -2.76 V vs. Fc/Fc+ on the c-CdS/a-Cd(OH)2/CP electrode. The excellent performance of this electrode was mainly ascribed to its special three-dimensional structure and the introduction of a-Cd(OH)2. These structures could provide more active sites, accelerate the charge transfer, and enhance adsorption of *COOH intermediates, thereby improving the CO selectivity. Moreover, the electrolytes consisting of 1-butyl-3-methylimidazolium tetrafluoroborate and acetonitrile also enhanced the reaction kinetics of electrochemical CO2 reduction to CO.

Asymmetric Coordination of Bimetallic Fe-Co Single-Atom Pairs toward Enhanced Bifunctional Activity for Rechargeable Zinc-Air Batteries.

The advancement of rechargeable zinc-air batteries (RZABs) faces challenges from the pronounced polarization and sluggish kinetics of oxygen reduction and evolution reactions (ORR and OER). Single-atom catalysts offer an effective solution, yet their insufficient or singular catalytic activity hinders their development. In this work, a dual single-atom catalyst, FeCo-SAs, was fabricated, featuring atomically dispersed N3-Fe-Co-N4 sites on N-doped graphene nanosheets for bifunctional activity. Introducing Co into Fe single-atoms and secondary pyrolysis altered Fe coordination with N, creating an asymmetric environment that promoted charge transfer and increased the density of states near the Fermi level. This catalyst achieved a narrow potential gap of 0.616 V, with a half-wave potential of 0.884 V for ORR (vs the reversible hydrogen electrode) and a low OER overpotential of 270 mV at 10 mA cm-2. Owing to the superior activity of FeCo-SAs, RZABs exhibited a peak power density of 203.36 mW cm-2 and an extended cycle life of over 550 h, exceeding the commercial Pt/C + IrO2 catalyst. Furthermore, flexible RZABs with FeCo-SAs demonstrated the promising future of bimetallic pairs in wearable energy storage devices.

Unveiling the role of proton concentration in dinuclear metal complexes for boosting photocatalytic CO2 reduction

The reaction kinetics of photocatalytic CO2 reduction is highly dependent on the transfer rate of electrons and protons to the CO2 molecules adsorbed on catalytic centers. Studies on uncovering the proton effect in catalysts on photocatalytic activity of CO2 reduction are significant but rarely reported. In this paper, we, from the molecular level, revealed that the photocatalytic activity of CO2 reduction is closely related to the proton availability in catalysts. Specifically, four dinuclear Co(II) complexes based on Robson-type ligands with different number of carboxylic groups (-nCOOH; n = 0, 2, 4, 6) were designed and synthesized. All these complexes show photocatalytic activity for CO2 reduction to CO in a water-containing system upon visible-light illumination. Interestingly, the CO yields increase positively with the increase of the carboxylic-group number in dinuclear Co(II) complexes. The one containing -6COOH shows the best photocatalytic activity for CO2 reduction to CO, with the TON value reaching as high as 10,294. The value is 1.8, 3.4, and 7.8 times higher than those containing -4COOH, -2COOH, and -0COOH, respectively. The high TON value also makes the dinuclear Co(II) complex with -6COOH outstanding among reported homogeneous molecular catalysts for photocatalytic CO2 reduction. Control experiments and density functional theory calculation indicated that more carboxylic groups in the catalyst endow the catalyst with more proton relays, thus accelerating the proton transfer and boosting the photocatalytic CO2 reduction. This study, at a molecular level, elucidates that more carboxylic groups in catalysts are beneficial for boosting the reaction kinetics of photocatalytic CO2 reduction.

Single-atom Al precisely modulate the strain of Pt3Co intermetallic for superior oxygen catalytic performance

Precisely controlling the strain of Pt-based intermetallic to ensure high performance and stability is a massive task for sustainable proton-exchange-membrane-fuel-cells. Herein, the Al single-atom was trapped into the L12-Pt3Co intermetallic core to precisely tailor the strain state on the Pt-skin for fast oxygen reduction reaction kinetics. Theoretical calculations firstly predicted that only tailored tension can accelerate the protonation of O2 on L12-Pt3Co@Pt without creating an additional energy barrier for subsequent oxygen-containing intermediates desorption. Experimentally, Al single-atom confined in the L12-Pt3Co lattice by substituting partial Co occupancy, imposing tailored ∼ 0.2 % tension on Pt-skin compared to the L12-Pt3Co. L12-Al-Pt3Co@Pt/C exhibits enhanced mass activity which is ten-time improvement over commercial Pt/C. More significantly, XAS and DFT results reveal that the Al single-atom can strengthen the Pt-Co bonding, enhancing the stability of L12-Al-Pt3Co@Pt/C in oxygen reduction. This work provides an avenue to design the strain by single-atom for sustainable energy conversion technologies.

The construction of Cs3MoxSbyBr9/BiVO4 S-scheme heterojunction photocatalyst for efficient photocatalytic N2 fixation

Synergistic nitrogen (N2) reduction with water (H2O) oxidation is meaningful but challenging owing to the inertness of the N2 molecule and the sluggish kinetics of H2O oxidation. Herein, a simutaneous-promotion strategy of redox capacities is presented for constructing a lead-free Cs3Sb2Br9-based S-scheme heterojunction, by decorating Mo-functionalized Cs3Sb2Br9 nanocrystals (Cs3MoxSbyBr9) on BiVO4 nanosheet through an in-situ plane-to-point growth manner. The Mo-functionalization for Cs3Sb2Br9 enables the regulation of the d-band center position, greatly improving surface reaction kinetics for N2 reduction. Furthermore, the construction of the S-scheme heterojunction enhances the driving force for H2O oxidation and spatial charge separation of photocatalysts. As anticipated, the resultant Cs3MoxSbyBr9/BiVO4 exhibits an excellent photocatalytic N2 reduction activity under ambient atmosphere, achieving ammonia (NH3) production at a rate of 300 ± 5 μmol g−1 h−1 under simulated sunlight illumination (100 mW cm−2), which is nearly 20-fold higher than that of pristine Cs3Sb2Br9.

Reverse Atom Capture on Perovskite Surface Enabling Robust and Efficient Cathode for Protonic Ceramic Fuel Cells.

Protonic ceramic fuel cells (PCFCs) hold potential for sustainable energy conversion, yet their widespread application is hindered by the sluggish kinetics and inferior stability of cathode materials. Here, a facile and efficient reverse atom capture technique is developed to manipulate the surface chemistry of PrBa0.5Sr0.5Co1.5Fe0.5O5+ δ (PBSCF) cathode for PCFCs. This method successfully captures segregated Ba and Sr cations on the PBSCF surface using W species, creating a (Ba/Sr)(Co/Fe/W)O3- δ (BSCFW)@PBSCF heterostructure. Benefiting from enhanced kinetics of proton-involved oxygen reduction reaction and strengthened chemical stability, the single cell using the optimized 2W-PBSCF cathode demonstrates an exceptional peak power density of 1.32W cm-2 at 650°C and maintains durable performance for 240h. Theoretical calculations unveil that the BSCFW perovskite delivers lower oxygen vacancy formation energy, hydration energy, and proton transfer energy compared to the PBSCF perovskite. This protocol offers new insights into advanced atom capture techniques for sustainable energy infrastructures.

Influence of Preoxidation Treatment on the Reduction Behavior and Reaction Kinetics of Vanadium Titanomagnetite by Hydrogen

Influence of Preoxidation Treatment on the Reduction Behavior and Reaction Kinetics of Vanadium Titanomagnetite by Hydrogen