Kbps Data Rate Research Articles

A Miniature Batteryless Bioelectronic Implant Using One Magnetoelectric Transducer for Wireless Powering and PWM Backscatter Communication.

Wireless minimally invasive bioelectronic implants enable a wide range of applications in healthcare, medicine, and scientific research. Magnetoelectric (ME) wireless power transfer (WPT) has emerged as a promising approach for powering miniature bio-implants because of its remarkable efficiency, safety limit, and misalignment tolerance. However, achieving low-power and high-quality uplink communication using ME remains a challenge. This paper presents a pulse-width modulated (PWM) ME backscatter uplink communication enabled by a switched-capacitor energy extraction (SCEE) technique. The SCEE rapidly extracts and dissipates the kinetic energy within the ME transducer during its ringdown period, enabling time-domain PWM in ME backscatter. Various circuit techniques are presented to realize SCEE with low power consumption. This paper also describes the high-order modeling of ME transducers to facilitate the design and analysis, which shows good matching with measurement. Our prototyping system includes a millimeter-scale ME implant with a fully integrated system-on-chip (SoC) and a portable transceiver for power transfer and bidirectional communication. SCEE is proven to induce >50% amplitude reduction within 2 ME cycles, leading to a PWM ME backscatter uplink with 17.73 kbps data rate and 0.9 pJ/bit efficiency. It also achieves 8.5 × 10-5 bit-error-rate (BER) at a 5 cm distance, using a lightweight multi-layer-perception (MLP) decoding algorithm. Finally, the system demonstrates continuous wireless neural local-field potential (LFP) recording in an in vitro setup.

Magnetoeletric Backscatter Communication for Millimeter-Sized Wireless Biomedical Implants

Magnetoelectric power transfer has shown remarkable promise for the development of wireless millimetric bioelectronic implants with its low tissue absorption, high efficiency, and low misalignment sensitivity. Utilizing the same physical mechanism for power and communication is critical for implant miniaturization. For the first time, we designed and demonstrated near-zero power magnetoelectric backscatter from mm-sized implants by exploiting the converse magnetostriction effects. The prototype system consists of an 8.2-mm3 wireless implant integrating an application-specific integrated circuit (ASIC) that achieves frequency-shift-keying backscattering via capacitive load modulation and a custom transceiver demodulating data through frequency-to-digital conversion. The magnetoelectric backscatter archives > 1 kbps data rate at the 335-kHz carrier frequency, with a communication distance greater than 2 cm and a bit error rate (BER) less than 1E-3.

Efficient Ambient LoRa Backscatter With On-Off Keying Modulation

Backscatter communication holds potential for ubiquitous and low-cost connectivity among low-power IoT devices. To avoid interference between the carrier signal and the backscatter signal, recent works propose a frequency-shifting technique to separate these two signals in the frequency domain. Such proposals, however, have to occupy the precious wireless spectrum that is already overcrowded, and increase the power, cost, and complexity of the backscatter tag. In this paper, we revisit the classic ON-OFF Keying (OOK) modulation and propose Aloba, a backscatter system that takes the ambient LoRa transmissions as the excitation and piggybacks the in- band OOK modulated signals over the LoRa transmissions. Our design enables the backscatter signal to work in the same frequency band of the carrier signal, meanwhile achieving flexible data rate at different transmission range. The key contributions of Aloba include: i) the design of a low-power backscatter tag that can pick up the ambient LoRa signals from other signals; ii) a novel decoding algorithm to demodulate both the carrier signal and the backscatter signal from their superposition. We further adopt link coding mechanism and interleave operation to enhance the reliability of backscatter signal decoding. We implement Aloba and conduct head-to-head comparison with the state-of-the-art LoRa backscatter system PLoRa in various settings. The experiment results show Aloba can achieve 39.5–199.4 Kbps data rate at various distances, 10.4– <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$52.4\times $ </tex-math></inline-formula> higher than PLoRa.

Low-Cost Underwater Communication System: A Pilot Study

The aim of the paper is to present a simplified implementation of quadrature phase shift keying (QPSK) based underwater communication system. The presented solution addresses the problem of developing inexpensive, compact ultrasound modems able to be mounted on underwater robots. Simplifications introduced into the modulation and demodulation of QPSK signals do not disturb any parameter of the data link. The paper indicates that it is possible to realize modulation and demodulation on a simple microcontroller. Many hints are given on how to use hardware blocks embedded in a microcontroller, such as ADC, DMA, timers, etc. Experiments performed with the prototype modems allow to reach 4 kbps data rate on a distance of about 18 m.

A Gated Oscillator Clock and Data Recovery Circuit for Nanowatt Wake-Up and Data Receivers

This article presents a data-startable baseband logic featuring a gated oscillator clock and data recovery (GO-CDR) circuit for nanowatt wake-up and data receivers (WuRxs). At each data transition, the phase misalignment between the data coming from the analog front-end (AFE) and the clock is cleared by the GO-CDR circuit, thus allowing the reception of long data streams. Any free-running frequency mismatch between the GO and the bitrate does not limit the number of receivable bits, but only the maximum number of equal consecutive bits (Nm). To overcome this limitation, the proposed system includes a frequency calibration circuit, which reduces the frequency mismatch to ±0.5%, thus enabling the WuRx to be used with different encoding techniques up to Nm = 100. A full WuRx prototype, including an always-on clockless AFE operating in subthreshold, was fabricated with STMicroelectronics 90 nm BCD technology. The WuRx is supplied with 0.6 V, and the power consumption, excluding the calibration circuit, is 12.8 nW during the rest state and 17 nW at a 1 kbps data rate. With a 1 kbps On-Off Keying (OOK) modulated input and −35 dBm of input RF power after the input matching network (IMN), a 10−3 missed detection rate with a 0 bit error tolerance is measured, transmitting 63 bit packets with the Nm ranging from 1 to 63. The total sensitivity, including the estimated IMN gain at 100 MHz and 433 MHz, is −59.8 dBm and −52.3 dBm, respectively. In comparison with an ideal CDR, the degradation of the sensitivity due to the GO-CDR is 1.25 dBm. False alarm rate measurements lasting 24 h revealed zero overall false wake-ups.

Review of 5&amp;lt;sup&amp;gt;th&amp;lt;/sup&amp;gt; Generation Wireless Mobile Network

Mobile wireless communication has experienced few generations. the first Technologies started with an analog system and developed into a digital communication system. 1G made possible for mobile communication, it has bandwidth between 10 kHz up to 30 kHz, this generation was first launched by Japanese company Nippon Telegraph and Telephone (NTT). in the second generation offered a 9.6 kbps data rate which increase up to 300 Kbps. it has second phase with 200 kHz bandwidth. In third generation Voice and data communication were focused. All generations were making diverse new features. Fourth generation (4G) technology was used in many countries around the world with providing high mobility and high-speed data rate by internet protocol (IP). However wireless communication systems facing new challenges every day which even fourth-generation cannot solve. Therefore, experts have already started an investigation also tested on beyond fourth-generation wireless systems with no limitation. To create new generation technology, companies and researchers need to focus five fundamental new technologies. These new technologies will deliver a good data rate less than a millisecond of a slowdown and bring a high speed of downlink. To realize how 5G technology is different from the current generation 4G, we need to understand all of these five technologies.

LoRadar: Enabling Concurrent Radar Sensing and LoRa Communication

Miniature radar has demonstrated its great potential in smart homes, such as understanding the wellness of the residents and providing ubiquitous interactions. While it has many promising applications, it also results in congested RF (radio frequency) environments as there is an unprecedented amount of traffic in a smart home. To ease the strain on the limited spectrum, we ask the question that, can we reuse the sensing signals for data communication? With such a capability, we can improve the spectrum utilization by sharing the spectrum between sensing and communication systems. However, radar signals are customized for the sensing purpose and are incompatible with legacy communication standards. To address this challenge, we have an observation that, non-linearity effect in RF circuits can convert wideband radar signals into a LoRa signal. Based on this observation, in this paper, we present LoRadar, which enables an FMCW (Frequency-Modulated Continuous Wave) radar to carry LoRa signals in sensing waves. We present both the downlink and uplink design, enabling a LoRadar device to communicate with LoRa nodes in a bi-directional way. We implement LoRadar and evaluation results show that LoRadar can achieve home-level coverage with 3.4kbps data rate while it preserves the sensing resolution of the radar.

HyperSight: A Precise Decoding Algorithm for VLC With Mobile-Phone Camera

In this paper, we propose and experimentally demonstrate HyperSight, which is a precise image decoding algorithm for the mobile-phone camera based visible light communication (VLC) system. The conventional algorithms have to select an appropriate column matrix, and then decode the image according to the fitting curve. The selection of the column matrix and the fitting of the function are not only time-consuming but also error-prone, leading to low decoding efficiency and high bit error rate (BER). While HyperSight calculates characteristic grayscale matrix to avoid column matrix selection and uses critical grayscale to replace the function fitting to decode the image. As expected, our algorithm not only reduces the BER, but also improves the processing performance. The experimental results show that, the BER can be reduced by two orders of magnitude on average compared with the conventional scheme. For the $4.8\,$ kbps data rate, our algorithm can achieve the transmission distance of $50\,$ cm under the $7\%$ forward error correction (FEC) threshold with the low illuminance of $702\,$ lux.

Live Wire – A Low-Complexity Body Channel Communication System for Landmark Identification

This paper presents a robust simplex Body Channel Communication (BCC) system aimed at providing an interactive infrastructure solution for visually impaired people. Compared to existing BCC solutions, it provides high versatility, wearability and installability in an environment in a low complexity hardware-software solution. It operates with a ground referred–transmitter (TX) and it is based on an asynchronous threshold receiver (RX) architecture. Synchronization, demodulation and packetizing and threshold control are completely software defined and implemented using MicroPython. The RX includes Bluetooth® (BT) radio connectivity and a cell-phone application provides push text-to-speech notifications to a smartphone. The hardware achieves a Packet Error Rate (PER) of <inline-formula><tex-math notation="LaTeX">$\sim$</tex-math></inline-formula> 0.1 at 550 kHz pulse center frequency, Synchronized-On Off Keying (S-OOK) modulation and 1 kbps data rate, for an average current consumption of 44 mA.

An RF-Energy Harvester and IR-UWB Transmitter for Ultra-Low-Power Battery-Less Biosensors

A fully integrated 802.15.4a-LRP-UWB-PHY- and ETSI-compliant impulse-radio ultra-wide-band (IR-UWB) transmitter (TX) front-end, powered by an RF-energy-harvester in 180 nm CMOS technology, is presented. The TX is working in the 7 GHz band transmitting with -42 dBm at 5.12 kbps data rate, consuming 1.89 μW. Two circuit implementations of RF-energy-harvesters are presented and, based on measurements, a combined and optimized structure is proposed which is capable of generating 5 μW dc-power at -13.3 dBm RF input power at a frequency of 868 MHz. According to the overall SoC power budget, this amount of harvested energy is sufficient to power the IR-UWB-TX front-end, an ADC with pre-amplifier and the digital core logic for a wireless bio-sensing chip. Furthermore, improvements of the presented IR-UWB TX circuitry are discussed.

A Fixed Rate Speech Coder Based on the Filter Bank Method and the Inflection Point Detection

A fixed rate speech coder based on the filter bank and the non-uniform sampling technique is proposed. The non-uniform sampling is achieved by the detection of inflection points (IPs). A speech block is band passed by the filter bank, and the subband signals are processed by the IP detector, and the detected IP patterns are compared with entries of the IP database. For each subband signal, the address of the closest member of the database and the energy of the IP pattern are transmitted through channel. In the receiver, the decoder recovers the subband signals using the received addresses and the energy information, and reconstructs the speech via the filter bank summation. As results, the coder shows fixed data rate contrary to the existing speech coders based on the non-uniform sampling. Through computer simulation, the usefulness of the proposed technique is confirmed. The signal-to-noise ratio (SNR) performance of the proposed method is comparable to that of the uniform sampled pulse code modulation (PCM) below 20 kbps data rate.

A 2.4 GHz ULP OOK Single-Chip Transceiver for Healthcare Applications

This paper describes an ultra-low power (ULP) single chip transceiver for wireless body area network (WBAN) applications. It supports on-off keying (OOK) modulation, and it operates in the 2.36-2.4 GHz medical BAN and 2.4-2.485 GHz ISM bands. It is implemented in 90 nm CMOS technology. The direct modulated transmitter transmits OOK signal with 0 dBm peak power, and it consumes 2.59 mW with 50% OOK. The transmitter front-end supports up to 10 Mbps. The transmitter digital baseband enables digital pulse-shaping to improve spectrum efficiency. The super-regenerative receiver front-end supports up to 5 Mbps with -75 dBm sensitivity. Including the digital part, the receiver consumes 715 μW at 1 Mbps data rate, oversampled at 3 MHz. At the system level the transceiver achieves PER=10 (-2) at 25 meters line of site with 62.5 kbps data rate and 288 bits packet size. The transceiver is integrated in an electrocardiogram (ECG) necklace to monitor the heart's electrical property.

수중에서 OFDM 변조를 이용한 음향 통신의 성능분석

The performance of underwater communication system is influenced on channel characteristic. Delay spread cause by reverberation and multi-path happen the ISI (Inter Symbol Interference) and reduces the communication performance. In this paper, we analyze the performance of acoustic communication experiment in underwater to use the OFDM (Orthogonal Frequency Division Multiplexing) technique for overcome the reverberation and multi-path. As a result, we acquired the BER of modulation techniques. The BER of 2kbps data rate is and BER of 4 kbps data rate is .

A 2 MHz Wireless CMOS Transceiver for Implantable Biosignal Sensing Systems

An implementation of an implantable sensing biosystem composes of a readout circuit, a power management block, an embedded microcontroller unit (MCU), an implantable drug delivery section and a wireless uplink transceiver system. This paper describes a bi-directional wireless transceiver system for implantable sensing systems. The transceiver system is composed of an external and implantable transceiver, communicating through an inductive link. Half duplex communication between transceivers at a 10 Kbps data rate was achieved at a maximum distance of 4 cm. Command and data will be supplied to the implantable module by radio frequency (RF) telemetry utilizing an amplitude shift keying (ASK) modulated 2 MHz carrier frequency. A capacitor-less amplitude demodulation receiver architecture was produced in the research with implantable receiver core area measuring at 113.2 µm by 171.8 µm with average power dissipation at 815.1 µW at a 3.3 V single rail power supply. An active uplink transceiver utilizing load shift keying (LSK) as backward data telemetry was designed. Implantable transmitter core area measures 251.7 µm by 139.3 µm, consuming 103.62 mW while driving an RF ferrite core antenna at maximum reading range. Integrating both circuits, implantable transceiver, measuring 355.3 µm by 171.8 µm, was designed and implemented using TSMC 0.35 µm mixed-signal 2P4M 3.3 V standard CMOS process. The integrated circuit solution addressed solutions for many of the problems associated with implanted devices and introduces circuits which improve in several ways over previously published designs, in functionality and integration level. In addition to being fully integrated in plain CMOS technology, not relying at least partly on available specialized elements and expensive technologies, these building blocks improve on previous designs in performance and/or power consumption. This work succeeded in implementing building blocks for an implantable transceiver, which depends only on the absolute minimum off-chip components. A complete implantable chip is presented, which highlight the design tradeoffs and optimizations applied to the design of CMOS implantable system chips.

A FREQUENCY OFFSET ESTIMATION AND COMPENSATION ALGORITHM FOR K/Ka-BAND COMMUNICATIONS

This paper presents a new open-loop technique for estimating and correcting Doppler frequency shift in K/Ka-band communication systems with special reference to the advanced communications technology satellite (ACTS) mobile terminal (AMT) modem, which utilizes square-wave pulse-shaped, binary differential phase shift-keyed (DPSK) modulation. The novelty of this estimation scheme is that it exploits the Doppler-induced phase shift over a fraction of a symbol interval to provide an estimate of the Doppler offset, without requiring symbol synchronization. Furthermore, by utilizing time-differential detection (delay-and-multiply), the proposed technique can tolerate much larger frequency offsets than existing open- or closed-loop techniques. Analytical results are provided for the variance of the above estimator and the error probability performance of the AMT is evaluated in the presence of the Doppler correction. Practical design considerations are also discussed, including a method for modifying the front end, digital bandlimiting filter in such a way that Doppler bias effects in the new estimator are eliminated. Simulation results reveal that, in general, performance improves with increasing data rates, i.e., the new frequency offset estimation/compensation algorithm induces a degradation from ideal of approximately 1 dB at a 6 dB energy per data symbol (bit) and a 2.4 kbps data rate. However, there is no appreciable degradation when the data rate is increased to 9.6 or 19.2 kbps.

A FREQUENCY OFFSET ESTIMATION AND COMPENSATION ALGORITHM FOR K/Ka‐BAND COMMUNICATIONS

This paper presents a new open-loop technique for estimating and correcting Doppler frequency shift in K/Ka-band communication systems with special reference to the advanced communications technology satellite (ACTS) mobile terminal (AMT) modem, which utilizes square-wave pulse-shaped, binary differential phase shift-keyed (DPSK) modulation. The novelty of this estimation scheme is that it exploits the Doppler-induced phase shift over a fraction of a symbol interval to provide an estimate of the Doppler offset, without requiring symbol synchronization. Furthermore, by utilizing time-differential detection (delay-and-multiply), the proposed technique can tolerate much larger frequency offsets than existing open- or closed-loop techniques. Analytical results are provided for the variance of the above estimator and the error probability performance of the AMT is evaluated in the presence of the Doppler correction. Practical design considerations are also discussed, including a method for modifying the front end, digital bandlimiting filter in such a way that Doppler bias effects in the new estimator are eliminated. Simulation results reveal that, in general, performance improves with increasing data rates, i.e., the new frequency offset estimation/compensation algorithm induces a degradation from ideal of approximately 1 dB at a 6 dB energy per data symbol (bit) and a 2⋅4 kbps data rate. However, there is no appreciable degradation when the data rate is increased to 9⋅6 or 19⋅2 kbps.