IOM Sampler Research Articles

Personal inhalable paper dust exposure and potential determinants among paper industry workers in Ethiopia

PurposeExcessive paper dust during paper production may harm the workers’ respiratory health. We wanted to assess the inhalable paper dust levels and its determinants among paper industry workers.MethodsA study was conducted in Ethiopia to assess the level of personal inhalable paper dust exposure among four paper mills. A total of 150 samples were collected using the IOM sampler attached to Side Kick Casella pumps at a flow rate of 2 L/min. The samples were analyzed in Nemko Norlab, Norway. Linear mixed-effect models were applied to identify determinants of inhalable paper dust.ResultsThe geometric mean of personal inhalable paper dust was 3.3 mg/m3 with 80% of the measurements exceeding the Swedish occupational exposure limit (OEL) of 2 mg/m3. The linear mixed-effects model showed that the level of dust was 28% higher when using high-speed than when using low-speed rewinding machines, while paper mills with an average of more than four machines per job group had 22% higher exposure than paper mills with a lower number of machines. Furthermore, working in packing and preparation was associated with higher dust exposure than in other areas.ConclusionsThe dust exposure levels were above the Swedish OEL for 80% of the samples. This indicates that preventive measures should be established in the industry. The exposure model identified high-speed rewinding machines, a high number of machines, and work in preparation and packing as associated with high levels of paper dust exposure.

Exposure to gallium arsenide nanoparticles in a research facility: a case study using molecular beam epitaxy

We evaluated GaAs nanoparticle-concentrations in the air and on skin and surfaces in a research facility that produces thin films, and to monitored As in the urine of exposed worker. The survey was over a working week using a multi-level approach. Airborne personal monitoring was implemented using a miniature diffusion size classifier (DiSCMini) and IOM sampler. Environmental monitoring was conducted using the SKC Sioutas Cascade Impactor to evaluate dimensions and nature of particles collected. Surfaces contamination were assessed analyzing As and Ga in ghost wipes. Skin contamination was monitored using tape strips. As and Ga were analyzed in urines collected every day at the beginning and end of the shift. The greatest airborne exposure occurred during the cutting operations of the GaAs Sample (88883 np/cm3). The highest levels of contamination were found inside the hood (As max = 1418 ng/cm2) and on the laboratory floor (As max = 251 ng/cm2). The average concentration on the worker’s skin at the end of the work shift (3.36 ng/cm2) was more than 14 times higher than before the start of the shift. In weekly urinary biomonitoring an average As concentration of 19.5 µg/L, which was above the Società Italiana Valori di Riferimento (SIVR) reference limit for the non-occupational population (2.0 – 15 µg/L), but below the ACGIH limit (30 µg/L). Overall, airborne monitoring, surface sampling, skin sampling, and biomonitoring of worker confirmed the exposure to As of workers. Systematic cleaning operations, hood implementation and correct PPE management are needed to improve worker protection.

11 Platinum Speciation in Air Samples

Abstract The health effects of chloroplatinates are generally well recognised and acknowledged by regulators in both EU and USA (Platinum salt sensitivity). But what about Platinum species? Speciation is essential for valid toxicology assessments and speciation studies are lacking in this respect – it’s known that certain Platinum chloro complexes are more sensitising than others. A method for the separation of platinum chloro-complexes and their hydrolysis products has been developed. The different platinum chemical species are separated into their charged compounds in 0.07 M HCl: [PtCl4]2-, [PtCl6]2-, [PtCl3(H2O)]-, [PtCl5(H2O)]- and a zero charged/ bis-aquo compound. The separation was carried via an ion exchange chromatographic column coupled to a quadrupole ICP-MS for the detection of the different anionic platinum chloro-species. A gradient program consisting of a mixture of HCl and HClO4 was used as eluent to ensure the separation of the species. A process has been developed for the analysis of platinum species extracted from air filters in a PGM facility with JM. Although the methodology for speciation is robust, further work needs to be carried out in terms of alternative sample collection to the air filters such as bubblers as the process of sonication, drying and acid contact on the filters does adversely affect the chemical species in solution. A comparison between Platinum speciation in air filters collected form IOM samplers and bubblers will be included in this presentation. This work will generate data to help characterise different workplaces based on the types of task-based exposure.

Review of Published Laboratory-Based Aerosol Sampler Efficiency, Performance and Comparison Studies (1994-2021).

We provide a narrative review on the published peer-reviewed scientific literature reporting sampler efficiency, performance and comparison studies (where two or more samplers have been assessed) in laboratory settings published between 1994 and 2021 (27 year period). This review is a follow-up to our narrative review on the published peer-reviewed scientific literature reporting sampler comparison in workplace settings. Search terms were developed for Web of Science and PubMed bibliographic databases. The retrieved articles were then screened for relevance, with those studies meeting the inclusion criteria being taken forward to data extraction (25 studies). The most common fraction assessed has been the inhalable fraction, with the IOM sampler being the most studied inhalable sampler and the SKC Aluminium cyclone being the most studied respirable sampler from the identified relevant articles. The most common aerosol used has been aluminium oxide. It was evident that standardisation for these sampler performance experiments is lacking. It was not possible to identify any discernible trends for the performance of samplers when assessed with different aerosols. The need for more detailed and informative data sharing from authors is highlighted. This includes provision of clear identifiable information on the samplers used for testing, sampler flow rates (both manufacturer and those actually used in the study, with an explanation given of any differences), detailed information on the test aerosols used and the sampler substrate materials used. An identified gap in the literature is the potential to perform studies aimed at revaluating the performance of samplers to allow any longer-term temporal changes in performance to be assessed. One approach in advancing the field is to produce an updated protocol for the laboratory testing of samplers. This updated protocol would be beneficial for both the research and occupational hygiene community and would allow harmonised assessment and reporting of sampler comparison studies.

Exposure to bacterial and fungal bioaerosols in facilities processing biodegradable waste.

The aim of the study was to determine the exposure of workers within biodegradable waste processing facilities to bacteria and fungi to identify any exposures of potential concern to health. Occupational measurements were performed in six composting and three bioenergy (bioethanol or methane/biogas) producing facilities. Bioaerosols were measured from breathing zones with Button aerosol or open face cassette filter samplers, and swab specimens were taken from the nasal mucous membranes of the workers. Aspergillus fumigatus, Bacillus cereus group, Campylobacter spp., Salmonella spp., Streptomyces spp., and Yersinia spp. were determined by real-time polymerase chain reaction (qPCR). A. fumigatus, and mesophilic and thermophilic actinobacteria were also cultivated from filters. Bacterial airborne endotoxins collected by IOM samplers were analyzed using a Limulus assay. Bioaerosol levels were high, especially in composting compared to bioenergy producing facilities. Endotoxin concentrations in composting often exceeded the occupational exposure value of 90 EU/m3, which may be harmful to the health. In addition to endotoxins, the concentrations of A. fumigatus (up to 2.4 × 105 copies/m3) and actinobacteria/Streptomyces spp. (up to 1.6 × 106 copies/m3) in the air of composting facilities were often high. Microbial and endotoxin concentrations were typically highest in waste reception and pre-treatment, equal or decreased during processing and handling of treated waste, and lowest in wheel loader cabins and control rooms/outdoors. Still, the parameters measured in wheel loader cabins were often higher than in the control sites, which suggests that the use of preventive measures could be improved. B. cereus group, Salmonella spp., and Yersinia spp. were rarely detected in bioaerosols or nasal swabs. Although Campylobacter spp. DNA was rarely detected in air, as a new finding, Campylobacter ureolyticus DNA was frequently detected in the nasal mucous membranes of workers, based on partial 16S rDNA sequencing. Moreover, especially A. fumigatus and C. ureolyticus spp. DNA concentrations in swabs after the work shift were significantly higher than before the shift, which indicates their inhalation or growth during the work shift. Microbial qPCR analysis of bioaerosols and swab samples of nasal mucosa allowed measuring exposure in various work operations and during the work shift, identifying problems for health risk assessment to improve working conditions, and evaluating the effectiveness of preventive measures and personal protection of workers.

Occupational exposure and risk assessment for agricultural workers of thiamethoxam in vineyards

Dermal & inhalation exposure was examined and according to these results, risk assessment of agricultural workers to thiamethoxam was performed during pesticide mixing/loading and hand-held sprayer application (11 replicates, each of about 1000 L of spray suspension) in vineyards. For the whole body dosimetry (WBD), clothing (Outer and inner), gauze, and nitrile gloves were analyzed to determine dermal exposure using whole-body dosimetry exposure protocol. The inhalation exposure was measured using a glass fiber filter with an IOM sampler. Analytical method validation of exposure matrices was evaluated including the field recovery and breakthrough test. The dermal exposure amount during mixing/loading was 0.163 mg (0.0004% of the total mixed/loaded active ingredient [a.i.]), whereas there was no inhalation exposure. The gloves (0.154 mg, 94.5%) were the most exposed body parts followed by the chest and stomach (0.009 mg, 5.5%). During application, the dermal and inhalation exposure amounts were 32.3 mg (0.07% of the total applied a.i.) and 10.8 µg (2.4 × 10−6% of the total applied a.i), respectively. The shin (35.1%) had the highest exposure to pesticides, followed by the chest & stomach (15.6%) and pelvis (12.6%). In case of mixing/loading, the amounts of actual dermal exposure (ADE) and actual inhalation exposure (AIE) were 0.0 and 0.0 μg/day, while those of ADE and AIE were 4707.6 and 15.8 μg/day for application. In risk assessment of the two different scenarios, the risk index was much lower than 1 (mixing/loading:0.000, application:0.014), indicating that vineyard workers are at low risk of thiamethoxam exposure. To determine the validity of the risk assessment using WBD method, the urinary metabolite was analyzed. Comparison of biomonitoring data and WBD exposure data show a reliable correlation (r = 0.885, p = 0.0003), suggesting that these are suitable methods to estimate exposure.

Occupational exposure to inhalable and respirable wood dust of pedunculate oak (Quercus robur L.) in a furniture factory

Given the well-known carcinogenicity of hardwood dust, occupational exposure to oak wood dust has been determined in a furniture factory on different wood processing machines during sanding, planing, and milling. Determination of the mass concentrations of respirable and inhalable oak wood dust from ambient air was performed using personal sampling pumps and two types of filter holders: the Higgins-Dewell respirable dust cyclone, manufactured by Casella (Bedford, UK), and the inhalable dust IOM sampler manufactured by SKC (Dorset, UK). Out of a total of 30 values of inhalable mass concentration, 7 (23%) exceeded the occupational exposure level (OEL). The highest exposure levels for inhalable and respirable wood dust from the belt sander were 1.569 to 3.710 mg/m3 and 0.243 to 1.342 mg/m3, respectively. Worker exposure may be below the level of increased risk of 2 mg/m3 if a machine such as a planer or router is connected to a suction system. The share of respirable particles in the inhalable fraction ranged between 12% and 31%, and for samples with an inhalable mass concentration exceeding 2 mg/m3, the share was lower than 16%, with a slightly decreasing tendency. Thus, the risk of lower respiratory tract diseases increases with higher exposure to inhalable particles, and the OEL is an indirect measure of protection against exposure to respirable particles.

Hygienic Monitoring of Working Area Air Pollution by Particulate Matter of ticagrelator in the Pharmaceutical Factory

Introduction. Hygienic monitoring of air pollution at the pharmaceutical enterprise required by the law of the Russian Federation (orders, standards, methodological guidelines and guidelines). This requirement follows from the need to protect the personnel of the pharmaceutical plant from the adverse air conditions of the working area, which may contain suspended solids of active pharmaceutical ingredient (API). Despite the use of breathing equipment by staff and occupational safety requirements, the risk to workers should be minimized by regular assessment of air pollution. Aim. The purpose of the stady is to carry out hygienic monitoring of working area air tikagrelor – API of the medicinal preparation Brilinta®. Materials and methods. The subject of this research is API ticagrelor including air and flush samples from the surface of LLC «AstraZenica Industries», collected during the production of the consignment of Brilinta® (MNN – ticagrelor). Air samples of the working area were collected using air intake systems of type "IOM Sampler", using both personal and stationary systems. Flushing from the surface is done by template v printing using cotton swaps. Sampling points selected to cover. All stages of the production cycle. Subsequently, the quantification of ticagrelor in samples was carried out by the method of high-efficiency liquid chromatography with UV detection (HPLC-UV). Results and discussions. The quantitative determination showed that 4 air samples and 25 surface fluxes exceeding the allowable content of ticagrelor. Each sample was related to the time and place of sampling, and assumptions were made as to why the sample points exceeded the standard values. Conclusion. At the pharmaceutical enterprise we have carried out hygienic monitoring of the working area air for the content of API ticagrelor. The results of the measurements were obtained and processed, on the basis of which measures were proposed to reduce the concentration of ticagrelor in the air in order to protect personnel from the adverse effects of the work area. These measures include optimization of process operations and/or training of personnel in new approaches to the operation and cleaning of equipment.

Analysis of the airborne mercury and particulate arsenic levels close to an abandoned waste dump and buildings of a mercury mine and the potential risk of atmospheric pollution

The project SUBproducts4LIFE is a research project financed by the European Union within the framework of the LIFE programme which proposes to demonstrate innovative circular economy concepts by the reuse of industrial subproducts/waste (coal ash and gypsum from coal power plants, blast furnace slag and steelmaking slag from steel factories) for the remediation at a real scale of contaminated soils and brownfield areas related to Hg mining. The area it is developing includes the waste dumps and demolition waste of the metallurgical plant of the abandoned mercury mine La Soterraña in Asturias, Northern Spain. Before this restoration research project takes place, this paper aims to evaluate airborne mercury and arsenic levels in land strongly contaminated with arsenic and mercury. The goal is to evaluate the air quality and compare it with international literature under reference levels. The study sampled gaseous mercury with a high-resolution direct reading device (LUMEX RA-915) and arsenic and mercury particulates with an IOM sampler, Casella personal pump, analyzed in the laboratory, to ensure the Health and Safety of workers, visitors and pedestrians walking near the mine and near the villages. The study concludes that As and Hg levels in the air are below 1 μg/m3 for the general public and villages near the mine. For works in the rubble area in the mine, it is recommended that workers use personal protective equipment and control measures are used to keep arsenic and mercury levels as low as technically possible.Article HighlightsGaseous Hg and airborne Hg and As particulates are measured in a strongly contaminated mercury mining and metallurgy site.High concentration of gaseous Hg is present in the strongly contaminated soils; therefore protective measures must be adopted for workers.Apart from an area with demolition rubble of a metallurgical plant, airborne Hg-As contamination is not harmful to workers or the general public.

Review of Workplace Based Aerosol Sampler Comparison Studies, 2004-2020.

We provide a narrative review on published peer-reviewed scientific literature reporting comparisons of personal samplers in workplace settings published between 2004 and 2020. Search terms were developed for Web of Science and PubMed bibliographic databases. The retrieved studies were then screened for relevance, with those studies meeting the inclusion criteria being taken forward to data extraction (22 studies). The inhalable fraction was the most common fraction assessed with the IOM sampler being the most studied sampler. The most common workplace environment where samplers had been compared was that where metals/metalloids were present. The requirements of EN13205 standard (Workplace exposure. Assessment of sampler performance for measurement of airborne particle concentrations) have also been considered, with these requirements not currently being met, or at least referred to, in the included published literature. A number of conclusions have been drawn from this narrative review. For studies that reported correction factors, no discernible trends could be identified. Correction factors also varied between samplers and settings, with correction factors varying from 0.67 for Button/IOM in agriculture settings to a correction factor of 4.2 for the closed face cassette/IOM samplers in aluminium smelters. The need for more detailed and informative data sharing from authors is highlighted, providing more context to both the sampling strategy and methodology, as well as the data analysis. It is recommended that the requirements of EN13205 are taken into account when designing sampler comparison studies at the workplace and that these are also reported. It is also considered that there is a need for a clear standardized workplace sampler comparison protocol to be developed, which can be used by the research and occupational hygiene community to allow more robust and transparent assessment of aerosol samplers and better-quality evidence for use by industrial hygienists, epidemiologists, and occupational safety specialists alike.

Determining Potassium Bromate in the Inhalable Aerosol Fraction in Workplace Air with Ion Chromatography.

BackgroundThe article presents the results of studies performed in order to develop a new method of airborne potassium bromate(V) determination at workplaces.MethodsThe method is based on a collection of the inhalable fraction of potassium bromate(V) using the IOM Sampler, then extraction of bromates with deionized water and chromatographic analysis of the obtained solution. The analysis was performed using ion chromatography with conductometric detection. The tests were performed on a Dionex IonPac®AS22 analytic column (250 × 4 mm, 6 μm) with AG22 precolumn (50 × 4 mm 11 μm).ResultsThe method provides for potassium bromate(V) determination within the concentration range of 0.043 ÷ 0.88 mg/m3 for an air sample of 0.72 m3 in volume, i.e., 0.1–2 times the exposure limit value as proposed in Poland. The method was validated in accordance with PN-EN 482. The obtained validation data are as follows: measuring range: 3.1–63.4 μg/mL, limit of detection (LOD) = 0.018 μg/mL and limit of quantification (LOQ) = 0.053 μg/mL. The developed method has been tested in the work environment, on laboratory employees having contact with potassium bromate(V).ConclusionThe analytical method allowed the determination of the inhalable fraction of airborne potassium bromate(V) at workplaces and can be used to assess occupational exposure.

Relative Differences in Concentration Levels during Sawing and Drilling of Car Bumpers Containing MWCNT and Organic Pigment.

Introduction. Knowledge on the exposure characteristics, including release of nanomaterials, is especially needed in the later stages of nano-enabled products’ life cycles to perform better occupational risk assessments. The objective of this study was to assess the concentrations during sawing and drilling in car bumpers containing multi-walled carbon nanotubes (MWCNTs) and nanosized organic pigment (OP) under variable realistic workplace situations related to the ventilation in the room and machine settings. Methods. Twelve different experiments were performed in triplicate (N = 36) using tools powered by induction engines that allow interference-free particle measurements. A DiSCmini was used to measure particle number concentrations, whereas particle size distributions were measured using Aerodynamic Particle Sizer (TSI), Scanning Mobility Particle Sizer (TSI), and Electrical Low Pressure Impactor (Dekati). In addition, inhalable particles were sampled using IOM samplers on filters for scanning electron microscope/energy-dispersive X-ray spectrometry (SEM/EDX) analyses. Data were analysed to estimate the effects of individual exposure determinants, in a two-stage modelling strategy using Autoregressive Integrated Moving Average models (stage 1) and subsequently combining first stage results in simulations using multiple linear regression models (stage 2). Results. In sawing experiments, partly melted carbon-rich particles (mainly ~2 to ~8 µm) were identified with SEM/EDX, whereas drilling experiments revealed no activity-related particles. In addition, no pristine engineered nanoparticles (MWCNTs and OP) were observed to be liberated from the matrix. Statistical analyses showed significant effects of a higher sawing speed, a reduction in air concentration due to mechanical ventilation, and less exposure during sawing of car bumpers containing MWCNTs compared to bumpers containing OP. Conclusion. The experiments in this study give an indication of the effects of different abrasive activities (sawing, drilling), machine settings (sawing speed, drill size), mechanical ventilation, and material characteristics on the manufactured nano-objects, their agglomerates, and aggregates concentration levels.

Performance evaluation of disposable inhalable aerosol sampler at a copper electrorefinery

This study evaluates the performance of the disposable inhalable aerosol sampler (DIAS), a new sampler developed to be more cost-effective than the traditional inhalable particle samplers and comparable to the inhalable particle sampling convention. Forty-eight pairs of the DIAS prototype and the IOM sampler were utilized to collect copper exposure measurements (23 personal and 25 area) at an electrorefinery facility. The geometric mean (GM) value of ratios of exposure data (DIAS/IOM) was 1.1, while the GM of ratios (DIAS/IOM) was 1.6 for the area exposure data, revealing 84% of the ratios were greater than one. For both personal and area exposure data, the concordance correlation coefficient tests revealed significant disagreements between the two types of samplers and suggested precision as the source of the disagreement. The estimated mean concentration was higher for the DIAS compared that for the IOM for the area exposure data (p < 0.05), while the results were comparable for the personal exposure data (p = 0.49). Overall, the DIAS generated higher exposure results compared to the IOM sampler for the area exposures. For the personal exposures, the findings were inconclusive due to inconsistent results of factors aforementioned. This study is limited to one metal component (copper) of the dust at a worksite. To date, this is the first field evaluation using personal exposure data to test the performance of the DIAS and the second evaluation using area exposure data. Thus, it will be necessary to conduct additional field evaluations with various elements to further evaluate the performance of the DIAS. In addition, particle migration to the internal walls of the cap was observed during the transportation of collected samples to a laboratory for both sampler types (6.4% for the DIAS and 7.4% for the IOM). Occupational health and safety professionals should be aware of potential errors caused from transferring samples from a field to a laboratory and should be careful not to exclude particles collected on the caps.

Relative Differences in Concentration Levels during Sawing and Drilling of Car Bumpers Containing MWCNT and Organic Pigment

Knowledge on the exposure characteristics, including release of nanomaterials, is especially needed in the later stages of nano-enabled products' life cycles to perform better occupational risk assessments. The objective of this study was to assess the concentrations during sawing and drilling in car bumpers containing multi-walled carbon nanotubes (MWCNTs) and nanosized organic pigment (OP) under variable realistic workplace situations related to the ventilation in the room and machine settings. Twelve different experiments were performed in triplicate (N = 36) using tools powered by induction engines that allow interference-free particle measurements. A DiSCmini was used to measure particle number concentrations, whereas particle size distributions were measured using Aerodynamic Particle Sizer (TSI), Scanning Mobility Particle Sizer (TSI), and Electrical Low Pressure Impactor (Dekati). In addition, inhalable particles were sampled using IOM samplers on filters for scanning electron microscope/energy-dispersive X-ray spectrometry (SEM/EDX) analyses. Data were analysed to estimate the effects of individual exposure determinants, in a two-stage modelling strategy using Autoregressive Integrated Moving Average models (stage 1) and subsequently combining first stage results in simulations using multiple linear regression models (stage 2). In sawing experiments, partly melted carbon-rich particles (mainly ~2 to ~8 µm) were identified with SEM/EDX, whereas drilling experiments revealed no activity-related particles. In addition, no pristine engineered nanoparticles (MWCNTs and OP) were observed to be liberated from the matrix. Statistical analyses showed significant effects of a higher sawing speed, a reduction in air concentration due to mechanical ventilation, and less exposure during sawing of car bumpers containing MWCNTs compared to bumpers containing OP. The experiments in this study give an indication of the effects of different abrasive activities (sawing, drilling), machine settings (sawing speed, drill size), mechanical ventilation, and material characteristics on the manufactured nano-objects, their agglomerates, and aggregates concentration levels.

A field evaluation of a single sampler for respirable and inhalable indium and dust measurements at an indium-tin oxide manufacturing facility

Indium-tin oxide production has increased greatly in the last 20 years subsequent to increased global demand for touch screens and photovoltaics. Previous studies used measurements of indium in blood as an indicator of indium exposure and observed associations with adverse respiratory outcomes. However, correlations between measurements of blood indium and airborne respirable indium are inconsistent, in part because of the long half-life of indium in blood, but also because respirable indium measurements do not incorporate inhalable indium that can contribute to the observed biological burden. Information is lacking on relationships between respirable and inhalable indium exposure, which have implications for biological indicators like blood indium. The dual IOM sampler includes the foam disc insert and can simultaneously collect respirable and inhalable aerosol. Here, the field performance of the dual IOM sampler was evaluated by comparing performance with the respirable cyclone and traditional IOM for respirable and inhalable indium and dust exposure, respectively. Side-by-side area air samples were collected throughout an indium-tin oxide manufacturing facility. Cascade impactors were used to determine particle size distribution. Several statistical methods were used to evaluate the agreement between the pairs of samplers including calculating the concordance correlation coefficient and its accuracy and precision components. One-way ANOVA was used to evaluate the effect of dust concentration on sampler differences. Respirable indium measurements showed better agreement (concordance correlation coefficient: 0.932) compared to respirable dust measurements (concordance correlation coefficient: 0.777) with significant differences observed in respirable dust measurements. The dual IOM measurements had high agreement with the traditional IOM for inhalable indium (concordance correlation coefficient: 0.997) but lower agreement for inhalable dust (concordance correlation coefficient: 0.886 and accuracy: 0.896) with a significantly large mean bias (-146.9 µg/m3). Dust concentration significantly affected sampler measurements of inhalable dust and inhalable indium. Results from this study suggest that the dual IOM is a useful single sampler for simultaneous measurements of occupational exposure to respirable and inhalable indium.

Concentrations and number size distribution of fine and nanoparticles in a traditional Finnish bakery

ABSTRACTIn bakeries, high concentrations of flour dust can exist and ovens release particles into the air as well. Particle concentrations (mass, number) and number size distribution may vary considerably but the variation is not commonly studied. Furthermore, the role of the smallest size fractions is rarely considered in the exposure assessment due to their small mass. The objectives of this work were to find out how concentrations and number size distribution of fine and nanoparticles vary in a traditional Finnish bakery and to determine the exposure of a dough maker to the nanoparticle fraction of the inhalable dust.Two measurement campaigns were carried out in a traditional, small-scale bakery. Sampling was performed at the breathing zone of the dough maker and three stationary locations: baking area, oven area, and flour depository. Both real-time measurements and conventional gravimetric sampling were conducted. Nanoparticle fraction of the inhalable dust was determined using an IOM sampler with a customized precyclone.Number concentration of fine and nanoparticles, and mass concentrations of both the inhalable dust and nanoparticles were high. The nanoparticle fraction was 9–15% of the inhalable dust at the breathing zone of the dough maker. Different sources, such as ovens and doughnut baking affected the number size distribution.Flour dust contained nanoparticles but most of the fine and nanoparticles were released into the air from the oven operations. However, nanoparticles are not a primary concern in bakeries compared to health effects linked to the large flour particles such as flour-induced sensitization or asthma and development of occupational rhinitis.

Validation protocol for whole-body dosimetry in an agricultural exposure study

Agricultural workers exposed to pesticides can experience adverse health impacts depending on toxicity and exposure amount. Whole-body dosimetry (WBD) is the most reliable, practical, and realistic method for measuring exposure. Since validation of analytical and experimental methodologies is critical for quantitative determination of exposure, we conducted a validation procedure to design an essential protocol for WBD exposure studies. Using the fungicide kresoxim-methyl, matrix-matched standards were prepared with various matrices including outer cloth, inner cloth, washing solution for gloves and hands, gauze, and glass fiber filter (IOM sampler) to determine the instrumental limit of quantitation for high-performance liquid chromatography (HPLC) (2 ng) and liquid chromatography–tandem mass spectrometry (LC–MS/MS) (10 pg). Method limits of quantitation (MLOQ) were also set for HPLC (0.1 mg/L) and LC–MS/MS (0.005 mg/L). We observed good analysis repeatability (coefficient of variation < 6%), and the linearity of the calibration curves was reasonable (r 2 > 0.998) in the range of 0.001–10 mg/L in various matrices. Recovery tests were carried out at three levels of concentration (MLOQ, 10 MLOQ, and 100 MLOQ) and resulted in good recoveries (72.7–105.6%). We did not observe breakthrough of the compound in tests of holding capacity for glass fiber pesticide filters. The procedures established in the present study are applicable as an essential, comprehensive protocol for exposure assessment studies using WBD.

A New Approach Combining Analytical Methods for Workplace Exposure Assessment of Inhalable Multi-Walled Carbon Nanotubes.

To date there is no consensus about the most appropriate analytical method for measuring carbon nanotubes (CNTs), hampering the assessment and limiting the comparison of data. The goal of this study is to develop an approach for the assessment of the level and nature of inhalable multi-wall CNTs (MWCNTs) in an actual workplace setting by optimizing and evaluating existing analytical methods. In a company commercially producing MWCNTs, personal breathing zone samples were collected for the inhalable size fraction with IOM samplers; which were analyzed with carbon analysis, inductively coupled plasma mass spectrometry (ICP-MS) and scanning electron microscopy/energy dispersive X-ray spectroscopy (SEM/EDX). Analytical methods were optimized for carbon analysis and SEM/EDX. More specifically, methods were applied and evaluated for background correction using carbon analyses and SEM/EDX, CNT structure count with SEM/EDX and subsequent mass conversion based on both carbon analyses and SEM/EDX. A moderate-to-high concordance correlation coefficient (RC) between carbon analyses and SEM/EDX was observed [RC = 0.81, 95% confidence interval (CI): 0.59-0.92] with an absolute mean difference of 59 µg m-3. A low RC between carbon analyses and ICP-MS (RC = 0.41, 95% CI: 0.07-0.67) with an absolute mean difference of 570 µg m-3 was observed. The large absolute difference between EC and metals is due to the presence of non-embedded inhalable catalyst particles, as a result of which MWCNT concentrations were overestimated. Combining carbon analysis and SEM/EDX is the most suitable for quantitative exposure assessment of MWCNTs in an actual workplace situation.

Determining exhaust fumes exposure in chainsaw operations

The objective of this study was to investigate the inhalation exposure of forest operators to polycyclic aromatic hydrocarbons (PAHs) and BTEX (benzene, toluene, ethylbenzene and total xylenes) contained in the exhaust fumes released from chainsaws and to suggest possible countermeasures. The study was carried out in four silvicultural treatments (coppice clearcut, conifer thinning, conifer pruning, and sanitary cut), using three types of chainsaw fuel (normal two-stroke petrol mix and two alkylate fuels). Eighty personal air samples were collected; IOM samplers combined with Amberlite XAD-2 sorbent tubes were used for collecting PAHs and Radiello® samplers were used for BTEX.Results indicate that none of the four silvicultural treatments significantly affected the PAHs and BTEX inhalation exposure of forest workers. On the other hand, statistically significant differences were recorded in the inhalation exposure to PAHs and BTEX when using different fuel types. In particular, the inhalation exposure to PAHs and BTEX was generally one order of magnitude lower when using modern alkylate fuels as compared to the traditional oil and lead-free petrol mixture. The small, non-statistically significant differences in inhalation exposure recorded between the two alkylate fuels suggests that the two fuels might be equivalent in terms of quality. Our study indicates that while forest workers are exposed to PAHs and BTEX, the maximum values are generally well below accepted occupational exposure limits.

Characterization of particle exposure in ferrochromium and stainless steel production

ABSTRACT This study describes workers’ exposure to fine and ultrafine particles in the production chain of ferrochromium and stainless steel during sintering, ferrochromium smelting, stainless steel melting, and hot and cold rolling operations. Workers’ personal exposure to inhalable dust was assessed using IOM sampler with a cellulose acetate filter (AAWP, diameter 25 mm; Millipore, Bedford, MA). Filter sampling methods were used to measure particle mass concentrations in fixed locations. Particle number concentrations and size distributions were examined using an SMPS+C sequential mobile particle sizer and counter (series 5.400, Grimm Aerosol Technik, Ainring, Germany), and a hand-held condensation particle counter (CPC, model 3007, TSI Incorporated, MN). The structure and elemental composition of particles were analyzed using TEM-EDXA (TEM: JEM-1220, JEOL, Tokyo, Japan; EDXA: Noran System Six, Thermo Fisher Scientific Inc., Madison,WI). Workers’ personal exposure to inhalable dust averaged 1.87, 1.40, 2.34, 0.30, and 0.17 mg m−3 in sintering plant, ferrochromium smelter, stainless steel melting shop, hot rolling mill, and the cold rolling mill, respectively. Particle number concentrations measured using SMPS+C varied from 58 × 103 to 662 × 103 cm−3 in the production areas, whereas concentrations measured using SMPS+C and CPC3007 in control rooms ranged from 24 × 103 to 243 × 103 cm−3 and 5.1 × 103 to 97 × 103 cm−3, respectively. The elemental composition and the structure of particles in different production phases varied. In the cold-rolling mill non-process particles were abundant. In other sites, chromium and iron originating from ore and recycled steel scrap were the most common elements in the particles studied. Particle mass concentrations were at the same level as that reported earlier. However, particle number measurements showed a high amount of ultrafine particles, especially in sintering, alloy smelting and melting, and tapping operations. Particle number concentration and size distribution measurements provide important information regarding exposure to ultrafine particles, which cannot be seen in particle mass measurements.