Introduction Of Exhaust Gas Recirculation Research Articles

Effect of exhaust gas recirculation(EGR) on combustion and emission of butanol/gasoline combined injection engine

N-butanol is a kind of biomass alcohol which can be produced by fermentation, and it is also a clean alternative fuel. The combustion and emissions characteristics of n-butanol/gasoline SI engine under different combined injection modes with the introduction of EGR was studied. N-butanol inlet injection plus gasoline in-cylinder direct injection is called N-GXDI; Gasoline inlet injection plus n-butanol in-cylinder direct injection is called G-NXDI. Through the analysis of combustion and emission performance under different EGR rates, injection modes and direct injection ratios (DIr), it is found that with the increase of DIr, cylinder temperature, pressure, and IMEP increase first and then decrease. Under the DIr = 50%, the combustion is more complete when the EGR rate is 5%. Under the same DIr, with the increase of EGR rate, CO emission decreased first and then increased, NOx emission opposite, THC emission increased. Under the same EGR rate, the total particle number of the two modes decreases first and then increases with the increase of DIr. The G-NXDI mode has advantages in combustion and primary emissions, while the N-GXDI mode has advantages in particulate emissions, suitable injection mode combined with EGR can greatly improve combustion and emission performance.

The combined effect of split fueling strategy and EGR on the combustion, performance, and emission characteristics of a CRDI biofuel engine

AbstractThe current research investigates the impact of a split fueling strategy combined with several flow rates of exhaust gas recirculation (EGR) on the combustion and emission characteristics of a diesel engine running on B20 waste cooking oil (WCO) biodiesel. A four‐stroke single‐cylinder common rail direct injection engine was employed for experiments. It operates with a B20 blend of WCO biodiesel at 600 bar pressure for varying pilot fueling conditions of 10%, 20%, and 30%. The B20 blend with 30% pilot fuel injection (B20P30) showed excellent performance and emission characteristics compared with B20 blend with 10% pilot fuel injection (B20P10) and B20 with 20% pilot fuel injection (B20P20). However, B20P30 had greater levels of nitrogen oxide (NOx) emissions than those by diesel. EGR discharge levels in 5% increments, ranging from 0% to 15% were introduced to address this issue. The experimental findings revealed that both cylinder peak pressure and heat release rate showed a reduction when the EGR flow rate was enhanced. The recirculation of exhaust gas into the combustion chamber led to a slight increase in the emission levels of hydrocarbon (HC), carbon monoxide (CO), and smoke, as well as a decrease in carbon dioxide (CO2). Nevertheless, the introduction of EGR significantly decreased NOx emissions by 22.94%, 35.05%, and 47.96% for EGR flow rates of 5%, 10%, and 15%, respectively, when compared with the engine operating without EGR. Overall, the two‐stage fueling strategy, B20P30 blended with 10% EGR corroborated to be beneficial in reducing NOx emissions with minimal performance penalties. Although there was a slight uptick in certain emissions, the overall trade‐off between emission reduction and performance was favorable. The culmination of this study is targeting the objectives of sustainable development goal 7 (clean energy) and goal 13 (climate action) to be achieved by 2030.

Performance enhancements and NOx emission reductions using novel exhaust-driven hybrid gas turbine inlet air-cooling techniques

For combined cycles, gas turbine inlet air-cooling (GTIAC) increases the mass flow rates of both air and the generated steam of the heat recovery steam generator and hence power output. The introduction of exhaust gas recirculation (EGR) to reduce NOx emissions necessitates the application of GTIAC to overcome the adverse effects of gas turbine (GT) inlet air heating that accompany EGR. For a hot-humid climate, the r5egular cooling methods consume a significant amount of energy while desiccant and inlet-fogging are not effective. The main purpose of this study is to introduce innovative exhaust-driven hybrid GTIAC techniques that can reduce effectively the inlet temperature of the combined cycle in a hot-humid climate without consuming a substantial amount of energy and examine the effects of applying such techniques on the performance and NOx emissions. In this paper, a thorough analysis for the effect of increasing ambient temperature ( To) and relative humidity ( RHo) on the performance and NOx emissions of the air-cooled GT combined cycle (ACGTCC) is presented and the novel exhaust-driven hybrid (NE-DH) GTIAC systems of desiccant-ejector, ejector-refrigeration, and desiccant-ejector-refrigeration are applied to ACGTCC and optimized for maximum power output. The 1-D model at the double choking was used to model the performance of the ejector GTIAC technique. The results indicate that applying NE-DH GTIAC techniques results in gains in power, which vary between 0.31% and 0.6% per °C rise in To and an efficiency improvement of up to about 0.5 percentage point and significant reductions in both capital and maintenance costs compared with applying the refrigeration GTIAC system. The introduction of ejector and desiccant cooling decreases NOx emissions further and adds no additional equipment cost if implemented together with EGR or some CO2 capture techniques. A suggested plan for GTIAC that reduces NOx emissions by up to 25% is presented.

Computational optimization of the performance of a heavy-duty natural gas pre-chamber engine

Optimization of the performance of a heavy-duty natural gas active pre-chamber (PC) engine was conducted using computational fluid dynamics (CFD) simulations. Seven different piston geometries were evaluated for their impact on engine performance. Unlike the narrow-throat PC, various piston geometries yielded a significant impact on the PC flow motion and fuel–air mixing process using the large-throat PC. Compared to flat-bottom pistons, ω-bottom pistons promoted the reverse flow from the MC and induced a broader lean-mixture distribution in the PC. For various ω-bottom pistons, enlarging the inner piston radius resulted in slower flame propagation within the PC, delaying the jet issuing and slowing down the turbulent flame propagation within the MC. The flat piston effectively reduced jet flame-piston interaction and promoted turbulent flame propagation within the squish region during the late combustion stage, but it generated higher wall heat transfer loss from the cylinder liner. A composite of ω- and flat-shaped pistons maintained the benefits of relatively high flame propagation speed within the squish region but low wall heat transfer loss, yielding the highest thermal efficiency of seven piston designs. The PC fueling ratio (PCFR) was found to be a critical factor in influencing the jet issuing process. A lower PCFR to establish a near-stoichiometric mixture within the PC promoted flame propagation and led to a faster jet ejection. An increase in compression ratio yielded higher engine efficiency due to the advanced combustion phasing and larger expansion ratio, it also resulted in higher wall heat transfer loss and nitric oxide (NOx) emission. The introduction of exhaust gas recirculation was able to effectively inhibit NOx formation, while also resulting in higher engine efficiency due to the lower wall heat transfer loss.

EFFECT OF EGR ON COMBUSTION AND EMISSION CHARACTERISTICS IN DIESEL BIOETHANOL DUAL-FUEL ENGINE

The diminution of global fossil fuel reserves is a main concern and alternative fuel sources are needed to tackle the issue of global warming caused by greenhouse gases. Biofuels have been considered as an alternative to the depleting oil resources. This study investigates the effect of exhaust gas recirculation (EGR) on combustion, performance and emission characteristics in a single-cylinder reactivity-controlled compression ignition engine using diesel-bioethanol as fuel. A dual-fueling strategy is achieved such that bioethanol is introduced into the intake manifold using a port-fuel injector (PFI) while diesel is directly injected into the combustion chamber. Various percentage of EGR rate were considered and compared. The important parameters that were taken into consideration are: engine efficiency, combustion characteristics, and exhaust gas emissions. Experimental results revealed that the EGR variation had a noticeable effect on the engine performance, emissions, and combustion characteristics with diesel-bioethanol dual fuel operation. Introduction of EGR has effectively reduced the combustion pressure rise rate along with keeping the NOx emission within the legislation norm. Besides, the results also revealed that the diesel-bioethanol dual fuel combustion has low smoke emission across all EGR ratios. Lastly, the results showed that the engine operating under diesel-bioethanol fueling could achieve high efficiency with near zero nitrogen oxides (NOx) and smoke emissions.

Effect of fuel composition and EGR on spark-ignited engine combustion with LPG fueling: Experimental and numerical investigation

This paper presents an experimental and numerical investigation of a spark-ignited (SI) cooperative fuel research (CFR) engine fueled with different liquefied petroleum gas (LPG) fuels and exhaust gas recirculation (EGR). The effects of LPG fuel composition on engine combustion characteristics are initially evaluated at two different compression ratios (CR). Results show normal combustion at CR 7 and heavy knocking combustion at CR 10 for all the tested fuels, with a more substantial impact for the LPG fuel with high proportions of n-butane species. The Livengood-Wu (LW) integral method is then used to analyze the knock occurrence risk of individual fuel based on the reactivity of the tested fuels. The introduction of EGR then demonstrates the potential of knock intensity reduction below the borderline knock limit. A zonal-based kinetic interactions study is also performed to understand the knock mitigation effectiveness of EGR over the pressure–temperature domain relevant to SI engine operation. Finally, a multidimensional, computational fluid dynamics (CFD) simulation model is shown to predict the LPG combustion characteristics and presents the evolution of in-cylinder temperature and chemical species to demonstrate the development of end-gas autoignition events without and with EGR.

Understanding the role of exhaust gas recirculation in gasoline/diesel dual-fuel combustion soot features

Exhaust gas recirculation (EGR) can not only mitigate the pressure rise rate but also reduce the NO x emissions in dual-fuel combustion, especially at high loads. With the introduction of EGR, the thermal, chemical, and dilution effects may alter the soot oxidation reactivity and related features. However, little research has been conducted on the effect of EGR on dual-fuel combustion soot features. The paper targets this gap by assessing the oxidation reactivity, morphology and nanostructure, and oxygenated surface functional groups of particulates from dual-fuel combustion with various EGR ratios. The results from thermogravimetric analysis showed that increasing EGR ratios decreased the mass distribution of volatile organic fraction and soot oxidation reactivity under the operating point. This indicated that introducing EGR in dual-fuel combustion would increase the regeneration temperature of diesel particulate filters. Owing to the dilution and thermal effects, mean primary particle diameter gradually increased with the increasing EGR ratio. Soot particulates produced by higher EGR ratios tended to a more graphitic structure, characterized by longer fringe length but smaller tortuosity from high resolution transmission electron micrograph (HRTEM) images. The Raman results also verified the observations from HRTEM. In addition, the concentration of C-OH slightly reduced with increasing EGR ratio, while that of C=O showed no clear trend.

Effects of Injection Overlap and EGR on Performance and Emissions of Natural Gas HPDI Marine Engine

ABSTRACT Due to the increasingly stringent emission regulations and the growing concern about energy hazard, natural gas (NG) has emerged as an alternative fuel with abundant reserves, low cost, high combustion performance and low pollutant emissions. In this study, a NG high pressure direct injection (HPDI) model is embedded in a Cummins ISX marine medium-speed four-stroke natural gas-diesel dual fuel (NGDDF) engine model. The strategies with different injection overlap of NG and pilot diesel oil (PDO) and different exhaust gas recirculation (EGR) were investigated, the following conclusions are drawn. At the same EGR rate, the injection start point of NG (SOING) has impact on the compression end pressure to some extent, while the injection end point of the pilot diesel oil (EOIPDO) makes little difference to the compression end pressure. With the increase of SOING, the maximum pressure (PMax) rises gradually. When the SOING remains unchanged, the longer the pilot diesel oil (PDO) injection lasts, the higher the PMax. The heat release rate (HRR) of HPDI engine has two peaks. The first one decreases as the EGR rate rises, while the other is inversely proportional only to the EGR rate. As the EGR rate increasing, the position of the second peak of HRR is increasingly delayed, irrespective of the injection strategy used. At the same EGR rate, the overlapping injection strategy has only a limited impact on the maximum in-cylinder temperature (about 42 K) and the soot emission (about 0.003 g/kwh). The first stage of nitrogen oxides (NOX) generation is closely related to the EGR rate. The higher the EGR rate, the longer the interval between the first and second stage of NOX generation. Though both reasonable injection overlap and delay of EOIPDO are conducive to reduce pollutant emissions, it remains necessary to delay the position of the overlap angle as much as possible, and the emission reduction effect of injection overlap will diminish as the EGR rate increasing. Either the injection overlap formed by delaying EOIPDO or advancing SOING has a positive impact on indicated mean effective pressure (IMEP). The introduction of EGR will increase indicated specific fuel consumption (ISFC) of the engine, while the injection overlap strategy can be used to reduce it by 5.35 g/kwh. In order to meet the Tier III standard, the combination of injection strategy B and 18% EGR can be considered as the most effective solution for soot, ISFC and IMEP factors.

Effect of induction on exhaust gas recirculation and hydrogen gas in compression ignition engine with simarouba oil in dual fuel mode

Biofuels extracted from non-edible oil is sustainable and can be used as an alternative fuel for internal combustion engines. This study presents the performance, emission and combustion characteristic analysis by using simarouba oil (obtained from Simarouba seed) as an alternative fuel along with hydrogen and exhaust gas recirculation (EGR) in a compression ignition (CI) engine operating on dual fuel mode. Simarouba biofuel blend (B20) was prepared on volumetric basis by mixing simarouba oil and diesel in the proportion of 20% and 80% (v/v), respectively. Hydrogen gas was introduced at the flow rate of 2.67 kg/min, and EGR concentration was maintained at 30% of total air introduction. Performance, combustion and emission characteristics analysis were examined with biodiesel (B20), biodiesel with hydrogen substitution and biodiesel, hydrogen with EGR and were compared with neat diesel operation. Results indicate that BTE of the engine operating with biodiesel B20 was decreased when compared to neat diesel operation. However, introducing hydrogen along with B20 blend into the combustion chamber shows a slight increase in the BTE by 1%. NOx emission was increased to 18.13% with the introduction of hydrogen than that of base fuel (diesel) operation. With the introduction of EGR, there is a significant reduction in NOx emission due to decrease in in-cylinder temperature by 19.07%. A significant reduction in CO, CO2, and smoke emissions were also noted with the introduction of both hydrogen and EGR. The ignition delay and combustion duration were increased with the introduction of hydrogen, EGR with biodiesel than neat diesel operation. Hence, the proposed biodiesel B20 with H2 and EGR combination can be applied as an alternative fuel in CI engines.

Knock analysis of bio-butanol in TISI engine based on chemical reaction kinetics

The knocking combustion of n-butanol (bio-butanol) combined with exhaust gas recirculation (EGR) in turbocharge direct injection spark ignition (TISI) engine with high compression ratio is studied. Mainly analyze the influence of EGR rate and composition on knock combustion and the indication effect of unconventional emission of free radicals on knock. The research results show that adding appropriate EGR can reduce the engine knock intensity, but the introduction of a large amount of EGR can cause the knock intensity to increase. When the EGR rate is 8%, the MAPO is less than 0.1 MPa, indicating that knocking combustion does not occur in the cylinder. When the EGR rate is increased to 15%, the MAPO is greater than 0.15 MPa, indicating that knocking combustion is intensified. Knock combustion is mainly concentrated on the intake side, which is related to the flame propagation speed. The addition of EGR can reduce the temperature in the cylinder, mainly because the specific heat capacity of H2O and CO2 in the EGR component is relatively large, which can significantly reduce the temperature of the mixture. The variation of CH2O, CH3CHO and C2H4 can reflect the knock intensity of the mixture in the cylinder. In conclusion, the introduction of EGR into the TISI engine can effectively reduce the knock intensity. The variation of mixture composition can better reflect the knock region and knock intensity.

Emission profiling of a common rail direct injection diesel engine fueled with hydrocarbon fuel extracted from waste high density polyethylene as a partial replacement for diesel with some modifications

A hydrocarbon fuel extracted from waste high-density polyethylene (WHDPE) by catalytic pyrolysis in a batch scale reactor is blended with diesel by 30% vol. (called as D70H30) is tested in a variable compression ratio engine equipped with a common rail system. Experiments were conducted at three compression ratios (16:1, 17.5:1, and 19:1) and exhaust gas re-circulation (EGR) rates (0%, 10%, and 20%) at the engine’s rated power to evaluate its combustion, performance and emission characteristics. The results revealed that, increasing the compression ratio resulted in higher peak cylinder pressure (PCP) and heat release rates (HRR). Introduction of EGR diminished both PCP and HRR peaks. The brake thermal efficiency of D70H30 blend was 4% lower than diesel at same operating conditions which got better at higher compression ratio without EGR. NOx emission was highest when injected at compression ratio 19:1 and at 0% EGR rate which was 6% and 3% higher than diesel and D70H30 blend operated at engine stock settings. In comparison with baseline diesel smoke opacity remained lower at all operating conditions, where lowest smoke emission was recorded at CR19 and at 0% EGR rate. UHC and CO emission followed the similar trend of smoke opacity. Whereas CO2 emission increased with compression ratio and reduced with induction of EGR. It can be concluded from the study that at higher compression ratio and low EGR rates D70H30 blend can be effectively utilized in a CRDi engine.

Exploring the high load potential of diesel–methanol dual-fuel operation with Miller cycle, exhaust gas recirculation, and intake air cooling on a heavy-duty diesel engine

Legislations concerning emissions from heavy-duty diesel engines are becoming increasingly stringent. This requires conventional diesel combustion to be compliant using costly and sophisticated aftertreatment systems. Preferably, diesel–methanol dual-fuel is one of the suitable alternative combustion modes as it can potentially reduce the formation of nitrogen oxide and soot emissions which characterised the diesel mixing-controlled combustion. This is primarily due to the high latent heat of vaporisation and oxygen content of the methanol fuel. At high engine loads, however, the potential of diesel–methanol dual-fuel operation is constrained by the excessive combustion pressure rise rate and peak in-cylinder pressure, which limits both the engine efficiency and the percentage of methanol that can be used. For the first time, experimental studies were conducted to explore advanced combustion control strategies such as Miller cycle, exhaust gas recirculation, and intake air cooling for improving upon high load diesel–methanol dual-fuel combustion. Experiments were carried out at 1200 r/min and 18 bar indicated mean effective pressure on a single-cylinder heavy-duty diesel engine, which equipped with a high pressure common rail diesel injection, a methanol port fuel injection, and a variable valve actuation system on the intake camshaft. Results showed that the methanol energy fraction of a conventional diesel–methanol dual-fuel operation with a baseline intake valve closing timing was limited to 28%. This was due to the high combustion temperature at a high load which advanced the ignition timing of the premixed charge, resulting in high levels of pressure rise rate. The application of lower effective compression ratio and intake air temperature ( Tint) effectively decreased the compression temperature, which successfully delayed the ignition timing of the premixed charge. This allowed for a more advanced diesel injection timing to achieve improvement in the thermal efficiency and potentially enabled a higher methanol substitution ratio. Although the introduction of exhaust gas recirculation demonstrated very slight impact on the ignition timing of the premixed charge, a higher net indicated efficiency was observed due to a relatively lower local combustion temperature which reduced heat transfer loss. Moreover, the optimised diesel–methanol dual-fuel operation allowed a higher methanol energy fraction of 40% to be used at an effective compression ratio of 14.3 and Tint of 305 K and achieved the highest net indicated efficiency of 47.4%, improving by 3.7% and 2.6%, respectively, when compared to the optimised conventional diesel combustion (45.7%) and conventional diesel–methanol dual-fuel (46.2%). This improvement was accompanied with a reduction of 37% in nitrogen oxide emissions and little impact on soot emissions in comparison with the conventional diesel combustion.

Variable valve actuation–based combustion control strategies for efficiency improvement and emissions control in a heavy-duty diesel engine

High nitrogen oxide levels of the conventional diesel engine combustion often requires the introduction of exhaust gas recirculation at high engine loads. This can adversely affect the smoke emissions and fuel conversion efficiency associated with a reduction of the in-cylinder air-fuel ratio (lambda). In addition, low exhaust gas temperatures at low engine loads reduce the effectiveness of aftertreatment systems necessary to meet stringent emissions regulations. These are some of the main issues encountered by current heady-duty diesel engines. In this work, variable valve actuation–based advanced combustion control strategies have been researched as means of improving upon the engine exhaust temperature, emissions, and efficiency. Experimental analysis was carried out on a single-cylinder heady-duty diesel engine equipped with a high-pressure common-rail fuel injection system, a high-pressure loop cooled exhaust gas recirculation, and a variable valve actuation system. The variable valve actuation system enables a late intake valve closing and a second intake valve opening during the exhaust stroke. The results showed that Miller cycle was an effective technology for exhaust temperature management of low engine load operations, increasing the exhaust gas temperature by 40 °C and 75 °C when running engine at 2.2 and 6 bar net indicated mean effective pressure, respectively. However, Miller cycle adversely effected carbon monoxide and unburned hydrocarbon emissions at a light load of 2.2 bar indicated mean effective pressure. This could be overcome when combining Miller cycle with a second intake valve opening strategy due to the formation of a relatively hotter in-cylinder charge induced by the presence of internal exhaust gas recirculation. This strategy also led to a significant reduction in soot emissions by 82% when compared with the baseline engine operation. Alternatively, the use of external exhaust gas recirculation and post injection on a Miller cycle operation decreased high nitrogen oxide emissions by 67% at a part load of 6 bar indicated mean effective pressure. This contributed to a reduction of 2.2% in the total fluid consumption, which takes into account the urea consumption in aftertreatment system. At a high engine load of 17 bar indicated mean effective pressure, a highly boosted Miller cycle strategy with exhaust gas recirculation increased the fuel conversion efficiency by 1.5% while reducing the total fluid consumption by 5.4%. The overall results demonstrated that advanced variable valve actuation–based combustion control strategies can control the exhaust gas temperature and engine-out emissions at low engine loads as well as improve upon the fuel conversion efficiency and total fluid consumption at high engine loads, potentially reducing the engine operational costs.

Injection Strategy in Natural Gas–Diesel Dual-Fuel Premixed Charge Compression Ignition Combustion under Low Load Conditions

Dual-fuel premixed charge compression ignition (DF-PCCI) combustion has been proven to be a viable alternative to conventional diesel combustion in heavy-duty compression ignition engines due to its low nitrogen oxides (NOx) and particulate matter (PM) emissions. When natural gas (NG) is applied to a DF-PCCI engine, its low reactivity reduces the maximum pressure rise rate under high loads. However, the NG–diesel DF-PCCI engine suffers from low combustion efficiency under low loads. In this study, an injection strategy of fuel supply (NG and diesel) in a DF-PCCI engine was investigated in order to reduce both the fuel consumption and hydrocarbon (HC) and carbon monoxide (CO) emissions under low load conditions. A variation in the NG substitution and diesel start of energizing (SOE) was found to effectively control the formation of the fuel–air mixture. A double injection strategy of diesel was implemented to adjust the local reactivity of the mixture. Retardation of the diesel pilot SOE and a low fraction of the diesel pilot injection quantity were favorable for reducing the combustion loss. The introduction of exhaust gas recirculation (EGR) improved the fuel economy and reduced the NOx and PM emissions below Euro VI regulations by retarding the combustion phasing. The combination of an NG substitution of 40%, the double injection strategy of diesel, and a moderate EGR rate effectively improved the combustion efficiency and indicated efficiency, and reduced the HC and CO emissions under low load conditions.

Experimental study on lean-burn characteristics of an SI engine with hydrogen/gasoline combined injection and EGR

Hydrogen has shown potential for improving the combustion and emission characteristics of the spark ignition (SI) dual-fuel engine. To reduce the additional NOx emissions caused by hydrogen direct injection, in this research, the cooperative control of the addition of hydrogen with exhaust gas recirculation (EGR) in the hydrogen/gasoline combined injection engine was investigated. The results indicate that both the addition of hydrogen and the use of EGR can increase the brake mean effective pressure (BMEP). As the αH2 value increases from 0% to 25%, the maximum BMEP increases by 9%, 12.70%, 16.50%, 11.30%, and 8.20%, respectively, compared with the value without EGR at λ = 1.2. The CA0-10 tends to increase with increases in the EGR rate. However, the effect of EGR in increasing the CA0-10 can be offset by the addition of 15% hydrogen at λ = 1.2. Measurements of the coefficient of variation of the indicated mean effective pressure (COVIMEP) indicate that the addition of hydrogen can effectively extend the EGR limit. Regarding gaseous emissions, NOx emissions, after the introduction of EGR and the addition of hydrogen, are lower than those of pure gasoline without EGR. An 18% EGR rate yields a significant reduction in NOx, reaching maximum decreases of about 82.7%, 77.8%, and 60% compared to values without EGR at λ = 1.0, 1.2, and 1.4, respectively. As the EGR rate increases, the hydrocarbon (HC) emissions continuously increase, whereas a blend of 5% hydrogen can significantly reduce the HC emissions at high EGR rates at λ = 1.4. Finally, according to combustion and emissions, the coupling of a 25% addition of hydrogen with 30% EGR at λ = 1.2, and the coupling of a 20% addition of hydrogen with an 18% EGR rate at λ = 1.4 yield the best results.

Emission Character Study on temperature Combustion Performance of Electronic Controlled Diesel Engine Mixed with Butanol

In this paper, through the electromechanical control modification of 4190 ZLC-2 diesel, the electronic fuel injection model is established by AMESim simulation software, and the high pressure circulation model of butanol/diesel dual fuel engine is established by AVL-FIRE software, the appropriate initial parameters module and corresponding boundary conditions are set. At the condition of low-temperature combustion through exhaust gas recirculation (EGR), in the optimization scheme studying the influence of butan blending ratio and EGR rate on diesel engine emissions. The result shows that the addition of butanol can improve the low temperature combustion, reducing the formation of CO and soot. The introduction of EGR can achieve low temperature combustion and significantly reduce NO emissions. The optimal parameter set for parameter matching is obtained: B20/EGR12.5 %.

Modeling and Analysis of Tier 4 Locomotives Operating in a High-Altitude Tunnel

Tunnels represent one of the most severe operating conditions for diesel engines in diesel-electric locomotive applications, specifically for nonventilated tunnels located at high elevation. High ambient air temperatures are observed in these tunnels due to heat rejected from the locomotive engines through the exhaust and engine cooling and lubrication systems. Engine protection algorithms cause the maximum allowable engine horsepower to be reduced due to these conditions leading to a reduction in train speed and occasionally train stall. A first law based model was developed to simulate the performance of a train pulled by GE diesel-electric locomotives equipped with medium speed diesel engines in a high altitude and nonventilated tunnel. The model was compared against and calibrated to actual tunnel operation data of EPA Tier 2 compliant locomotives. The model was then used to study the impact of engine design changes required for EPA Tier 4 compliant locomotives, specifically the introduction of exhaust gas recirculation (EGR), on engine, locomotive, and train performance in the tunnel. Simulations were completed to evaluate engine control strategies targeting same or better train performance than the EPA Tier 2 compliant locomotive baseline case. Simulation results show that the introduction of EGR reduces train performance in the tunnel by increasing the required reduction in engine horsepower, but is slightly offset by improved performance from other engine design changes. The targeted engine and train performance could be obtained by disabling EGR during tunnel operation.

Improvement of combustion and emissions with exhaust gas recirculation in a natural gas-diesel dual-fuel premixed charge compression ignition engine at low load operations

Dual-fuel premixed charge compression ignition (DF-PCCI) combustion has been demonstrated as a promising solution for simultaneous reduction of nitrogen oxides (NOX) and particulate matter (PM) emissions in heavy-duty compression ignition engines. The use of natural gas (NG) as the low-reactivity fuel in DF-PCCI combustion can expand the limited range of high load operations owing to the lower reactivity of NG than that of gasoline. However, the lower reactivity of NG results in significant hydrocarbon (HC) and carbon monoxide (CO) emissions at the low load operations. In this study, the mixture formations with and without exhaust gas recirculation (EGR) in NG-diesel DF-PCCI combustion were assessed to reduce the HC and CO emissions as well as to improve the fuel economy at low load operations. Diesel injection timing and NG substitution ratio (SR), which is defined as the proportion of energy stored in NG with respect to the total energy amount, were changed to examine the effects of the mixture formation on the DF-PCCI combustion. The NG SR, which was required to maintain the combustion phasing at a constant crank angle degree (CAD), was increased as the diesel injection timing was retarded in the mixture formation without EGR. The introduction of EGR, in addition to the diesel injection timing and the NG SR, contributed to the favorable mixture formation for the low load operations. The NOX and PM emissions were lower than the EURO VI limitations in both the mixture formations with and without EGR. When the EGR rate of 50% was applied, the indicated thermal efficiency (ITE) increased compared to the case without EGR. The increased ITE was due to the improved combustion efficiency, the higher peak heat release rate (HRR), and the shorter combustion duration. The HC and CO emissions also decreased significantly with the EGR.

Availability analysis on combustion of n-heptane and isooctane blends in a reactivity controlled compression ignition engine

Unfortunately, energy demands and destruction of the environment from uncontrolled manipulation of fossil fuels have increased. Climate change concerns have resulted in the rapid use of new, alternative combustion technologies. In this study, reactivity controlled compression ignition (RCCI) combustion, which can simply be exploited in internal combustion (IC) engines, is investigated. To introduce and identify extra insightful information, an exergy-based study was conducted to classify various irreversibility and loss sources. Multidimensional models were combined with the primary kinetics mechanism to investigate RCCI combustion, incorporating the second law of thermodynamics. The n-heptane, a highly reactive fuel, was supplied by direct injection into the cylinder, whereas premixed fuel was supplied through the intake port in an isooctane/ n-heptane RCCI engine. For five n-heptane increments (5%, 7.5%, 15%, 25%, and 40%) and six different exhaust gas recirculation (EGR) rates (0%, 10%, 20%, 30%, 40%, and 50%), accumulation of different exergy terms was calculated. The results show that as EGR introduction increases from 0% to 50%, the exergy destruction increases from 21.1% to 28.9%. Furthermore, the value of exhaust thermomechanical exergy decreases from 18.4% to 14.4% of the mixture fuel chemical exergy. Among the five different high reactive fuel mass regimes, the 40% n-heptane mass fraction has the major heat transfer exergy owing to its advanced CA50 that exerts a unique influence on cylinder charge temperature of heat transfer layer. The utilization efficiency of exhaust in RCCI is less affected by the variation of reactive fuel mass fraction by contrast; it will significantly influence heat transfer availability. This study revealed that with increasing reactive fuel ( n-heptane) from 7.5% to 40% the irreversibility decreased from 28.6% to 25.8% and the second law efficiency first increased from 43.2% to 44.6% at 15% n-heptane then decreased to 42.9% at 40% n-heptane.

Analysis of Exhaust Gas Recirculation (EGR) effects on exergy terms in an engine operating with diesel oil and hydrogen

Despite the fact that the high diffusivity of hydrogen in air leads to the fast mixing and homogeneous premixed mixture, it is not suitable for operation as a single fuel because it needs a high temperature to reach self-ignition; moreover, its operation results in knocking. In this study, a Deutz dual fuel (operation with diesel oil and hydrogen) was used and from the view point of second law the effects of EGR introduction was investigated. The fuel injection amount and gas fuel-air ratio were kept constant in 6.48 mg/cycle and øH2 = 0.3, respectively. For combustion simulation and exergetic analyses, the Extend Coherent Flame Model-Three Zone model (ECFM-3Z) and a FORTRAN-based code were used, respectively. For four EGR mass fraction cases (i.e. 0%, 10%, 20%, and 30%) the rate and accumulation of various exergy terms were calculated. The results showed that as EGR introduction increases from 0% to 30%, the exergy efficiency decreases from 42.4% to 14.1%. Furthermore, the value of exhaust loss exergy increases from 14.9% to 56.7% of the mixture fuel chemical exergy. The results of the current study were compared with those existing in the relevant literature, and an acceptable behavior was observed.