Simulated Intrapulpal Pressure Research Articles

Effect of Simulated Intrapulpal Pressure on Microtensile Bond Strength of Self-adhesive Resin Composite to Dentin

Effect of Simulated Intrapulpal Pressure on Microtensile Bond Strength of Self-adhesive Resin Composite to Dentin

Effects of dentin surface preparations on bonding of self-etching adhesives under simulated pulpal pressure.

ObjectivesThis study evaluated the effects of different smear layer preparations on the dentin permeability and microtensile bond strength (µTBS) of 2 self-etching adhesives (Clearfil SE Bond [CSE] and Clearfil Tri-S Bond Universal [CTS]) under dynamic pulpal pressure.Materials and MethodsHuman third molars were cut into crown segments. The dentin surfaces were prepared using 4 armamentaria: 600-grit SiC paper, coarse diamond burs, superfine diamond burs, and carbide burs. The pulp chamber of each crown segment was connected to a dynamic intra-pulpal pressure simulation apparatus, and the permeability test was done under a pressure of 15 cmH2O. The relative permeability (%P) was evaluated on the smear layer-covered and bonded dentin surfaces. The teeth were bonded to either of the adhesives under pulpal pressure simulation, and cut into sticks after 24 hours water storage for the µTBS test. The resin-dentin interface and nanoleakage observations were performed using a scanning electron microscope. Statistical comparisons were done using analysis of variance and post hoc tests.ResultsOnly the method of surface preparation had a significant effect on permeability (p < 0.05). The smear layers created by the carbide and superfine diamond burs yielded the lowest permeability. CSE demonstrated a higher µTBS, with these values in the superfine diamond and carbide bur groups being the highest. Microscopic evaluation of the resin-dentin interface revealed nanoleakage in the coarse diamond bur and SiC paper groups for both adhesives.ConclusionsSuperfine diamond and carbide burs can be recommended for dentin preparation with the use of 2-step CSE.

Evaluation of shear bond strength of various adhesives under Simulated intrapulpal pressure: An in vitro study.

Introduction:The presence of pulpal fluid can influence dentin bonding. This study aimed to evaluate the shear bond strength of universal dental adhesives under simulated intrapulpal pressure.Materials and Methods:Forty intact maxillary premolars were distributed into four groups (Group 1 – 3M ESPE Adper Single Bond 2 total etch adhesive, Group 2 – 3M ESPE Single Bond Universal, Group 3 – Prime and Bond universal adhesive, and Group 4 – Ivoclar Tetric N Bond Universal). Adhesive restorative procedures were carried under intrapulpal pressure simulation following which it was subjected to a shear load of 0.5 mm/min. Fracture mode analysis was performed using a stereomicroscope. The data obtained were subjected to ANOVA and Tukey post hoc test with a P < 0.05.Results:Highest bond strength was exhibited by Group 3 (7.01 ± 2.02 MPa) and least by Group 1 (5.36 ± 3.03 MPa). However, there were no statistical differences among the groups. Group 1 and 2 showed mostly cohesive failure, whereas Group 3 and 4 showed mixed failure.Conclusion:The results demonstrated that the experimental universal adhesive agents exhibited comparative shear bond strength when subjected to pulpal pressure. Pulpal pressure has a significant effect on bond strength.

Effect of the additive dentine conditioning in all-in-one adhesives on the bonding strength at simulated intrapulpal pressure

The aim of the study was to investigate the influence of additive etching of dentine with phosphoric acid on the shear bond strength of two different, self-conditioning, all-in-one adhesives [Adect (ADE), and One-Up-Bond F (OUP)].

Effect of intrapulpal pressure on the bonding strength of resin cement to dentin

OBJECTIVE To evaluate the effect of intrapulpal pressure simulation on the micro-tensile bond strength (μTBS) of resin cement to dentin. METHODS Thirty extracted human third molars were selected. Occlusal enamel was removed to expose dentine surface and teeth with residual dentin thickness of 0.5-2.5 mm were selected. Dye permeation through dentin tubules with or without intrapulpal pressure (IPP) simulation, or after Single Bond Universal (SBU) application on dentin surface with IPP simulation were observed at the end of 0 min, 5 min, 30 min and 2 h. The teeth with residual dentin thickness of (1.0±0.1) mm were divided into 2 groups with IPP simulation of 15 or 0 cmH2O (1 cmH2O=0.098 kPa), which was maintained for 30 min before bonding procedure. SBU was applied on the dentin surface and light cured, then RelyX Ultimate (RLX) cement was heaped on the dentin surface (diameter=10 mm, height=4 mm) and light-cured. After the dentin-resin cement samples were stored in distilled water for 24 h at 37 °C, the samples were cut into beams with cross sectional area of 0.9 mm×0.9 mm for μTSB testing (n=100). The data were analyzed with two independent samples t-test (α=0.05). The fracture mode was observed using scanning electron microscopy (SEM). The results were analyzed with Fisher exact test (α=0.05). The rest of dentin-resin cement samples (five samples for each group) were cut perpendicular to the bonding interface and the morphology of the bonding interface was observed using SEM. RESULTS The dye permeation through dentin tubules with IPP simulation was faster than those without IPP simulation. The μTSB of RLX to dentin with and without IPP simulation were (26.26±9.78) MPa and (28.70±9.0) MPa, respectively. The most frequent fracture mode was mixed-fracture mode. There was no significant difference between the two groups for neither bond strength nor fracture types distribution (P>0.05). Regarding the morphology of dentin-resin cement bonding interface, both groups showed 4-8 μm finger-like resin tags. CONCLUSION With SBU pretreatment, the IPP simulation had no influence on the immediate bond strength of RLX to dentin.

Mineral density in carious dentine after treatment with calcium silicates and polyacrylic acid-based cements.

To test the hypothesis that polyacrylic acid-based and calcium silicate materials are able to increase mineral density of artificially demineralized dentine produced by a microcosm model for caries formation. Forty-five dentine cavities were prepared in nine sound human third molars (five in each tooth). Specimens received a bacterial inoculum and were incubated in BHI plus 5% of sucrose for 96h to allow biofilm formation. After that, the specimens were scanned in a high energy micro-CT (baseline stack) and then, each cavity was filled with different cements: zinc polycarboxylate (Poly Zinc™, Prevest DenPro, Jammu, India), conventional glass-ionomer (Ketac Molar, 3M ESPE, Seefeld, Germany) and two calcium silicate-based materials (MTA, Angelus, Londrina, Brazil and Biodentine™, Septodont, Saint Maur des Fosses, France) whilst the central cavity was filled with utility wax (negative control). Specimens were kept for 45days under simulated intrapulpal pressure using simulated body fluid and after, they were again scanned (treated stacks). Reconstruction of the acquired projections was accomplished using standardized parameters, and the percentage mineral density change was calculated around each cavity. Data were tested for normality using the Shapiro-Wilk test, followed by nonparametric methods. A microcosm artificial caries model was able to cause dentine demineralization (±90% related to sound dentine). Significant increases in dentine mineral density were achieved using MTA or Poly Zinc™ (43.56% and 41.64% remineralization), followed by Biodentine™ (36.40%) and Ketac Molar (32.54%), P<0.05. All cements increased mineral density in demineralized dentine, but zinc polycarboxylate cement and MTA had greater bioactive potential. Micro-CT proved to be an effective method to evaluate changes in mineral density within dentine in contact with bioactive materials.

Microshear Bond Strength of High-viscosity Glass-ionomer to Normal and Caries-affected Dentin Under Simulated Intrapulpal Pressure.

The use of high-viscosity glass-ionomer cements (HVGICs) for atraumatic restorative treatment (ART) restorations is widely practiced with the advent of various HVGICs. However, the bonding of the latter to caries-affected dentin (CAD) should be validated, especially because it is the common substrate left after conservative caries removal following the ART approach. Hence, this study was carried out to evaluate the microshear bond strength (μSBS) of three HVGICs to normal dentin (ND) and CAD under intrapulpal pressure (IPP) simulation. The occlusal enamel of 90 molars with mid-coronal caries was cut to expose flat dentin surfaces containing both ND and CAD. Dentin substrates (ND and CAD) were differentiated using visual, tactile, caries-detecting dye, and dye-permeability methods. Prepared crown segments were equally divided (n=30) according to the tested HVGICs into GC Fuji IX GP Fast, Fuji IX GP containing chlorhexidine, and zinc-reinforced ChemFil Rock HVGIC. Microcylinders of tested HVGICs were built up on both dentin substrates (n=30 for each tested HVGIC per each substrate) using starch tubes while the specimens were subjected to simulated IPP of 15 mm Hg. The μSBS test was conducted using a universal testing machine, and failure modes were determined using a scanning electron microscope. Data were statistically analyzed using two-way analysis of variance (ANOVA) with repeated measures, one-way ANOVA, and Bonferroni post hoc tests (α=0.05). For both dentin substrates (ND and CAD), the μSBS values of ChemFil Rock were significantly higher than those recorded for the other HVGICs. The μSBS values of each tested HVGIC to ND and CAD were not statistically different. Failure modes were mainly mixed. Zinc-reinforced HVGIC ChemFil Rock showed superior bonding to ND and CAD compared to the GC Fuji IX GP Fast and Fuji IX with chlorhexidine. However, each of the tested HVGICs showed comparable bonding to both dentin substrates (ND and CAD).

One-year Adhesive Bond Durability to Coronal and Radicular Dentin Under Intrapulpal Pressure Simulation.

To evaluate the microtensile bond strength (μTBS) of different adhesives to coronal vs radicular dentin after one year of storage in artificial saliva and under intrapulpal pressure (IPP) simulation. Roots of 36 freshly extracted premolars were sectioned 5 mm apical to the cemento-enamel junction and pulp tissue was removed. Buccal enamel and cementum were trimmed to obtain standardized flat dentin surfaces. Specimens were divided into three groups (n=12/group) according to the adhesive strategies utilized: a two-step etch-and-rinse adhesive; a two-step self-etch adhesive; and a single-step self-etch adhesive. Adhesives and resin composite were applied to coronal and radicular dentin while the specimens were subjected to IPP simulation. After curing, specimens were stored in artificial saliva at 37°C in a specially constructed incubator while the IPP was maintained for either 24 hours or one year prior to testing. Bonded specimens were sectioned into sticks with a cross section of 0.8 ± 0.01 mm(2) and subjected to μTBS testing. Data were statistically analyzed using multi-way analysis of variance (ANOVA) with repeated measures; one-way ANOVA tests; and Bonferroni post hoc test (p<0.05). Failure modes were determined using a scanning electron microscope at 100× magnification. ANOVA results revealed a statistically significant effect for the adhesive strategy (p<0.001) and storage period (p<0.001) as well as for their interaction (p=0.024) on the μTBS. However, dentin substrate and its interactions revealed no significant effects. For both dentin substrates, the two-step self-etch adhesive revealed statistically significantly higher μTBS values than did the other two adhesives after 24 hours and one year of storage. After one-year storage, a significant decrease in bond strength values of all tested adhesives occurred with both dentin substrates. Modes of failure were mainly adhesive and mixed. Adhesives were not sensitive to structural differences between coronal and radicular dentin even after one year of storage under IPP simulation. However, all tested adhesive systems strategies were sensitive to storage.

Durability of solvent-free one-step self-etch adhesive under simulated intrapulpal pressure.

Background There are different solvents presented in simplified adhesives. Bond-1 SF has been developed, which contains neither water nor organic solvents, in order to eliminate technical issues in terms of evaporation of solvents and concerns for the durability of resin-dentin bond. Thus this study was conducted to evaluate the microtensile bond strength (?TBS) of solvent-free and ethanol-based one-step self-etch adhesives to dentin under simulated intrapulpal pressure (IPP). Material and Methods Occlusal surfaces of human molars were prepared to expose mid-dentin depth. Bond-1SF Solvent-Free SE [SF] and AdperTM easy one adhesives [AE] were applied on dentin specimens. Resin composite build up was done in increments. Then specimens were stored under simulated IPP 20 mmHg, immersed in artificial saliva at 37 ºC for 24 hours (24h) and 6 months (6m). Specimens were sectioned into sticks of (1 mm²) to be tested for (?TBS) using a universal testing machine. Both fractured sections of each stick were inspected using a stereomicroscope at 40× magnification to determine the mode of failure. Data were statistically analyzed by Two-way ANOVA of Variance. Results There was no statistically significant difference between the mean ?TBS of both [SF] and [AE] adhesives at both aging periods, 24h and 6m (p< 0.1103) and (p< 0.7148) respectively. Only for [AE] there was statistical significance for aging periods (p< 0.0057*). The most represented modes of failure were adhesive failure at tooth side. Conclusions Under simulated IPP solvent-free adhesive [SF] had comparable performance as ethanol-based adhesive [AE] when bonded to dentin substrate. Key words:Bond strength, dentin, simulated intrapulpal pressure, self-etch adhesives, solvents.

Effect of preheating of low shrinking resin composite on intrapulpal temperature and microtensile bond strength to dentin

The effect of preheating of the silorane-based resin composite on intrapulpal temperature (IPT) and dentin microtensile bond strength (μTBS) was evaluated. For the IPT, teeth (n=15) were sectioned to obtain discs of 0.5mm thickness (2 discs/tooth). The discs were divided into three groups (n=10/group) according to the temperature of the Filtek LS™ silorane-based resin composite during its placement, either at room temperature (23±1°C) or preheated to 54°C or 68°C using a commercial Calset™ device. Discs were subjected to a simulated intrapulpal pressure (IPP) and placed inside a specially constructed incubator adjusted at 37°C. IPT was measured before, during and after placement and curing of the resin composite using K-type thermocouple. For μTBS testing, flat occlusal middentin surfaces (n=24) were obtained. P90 System Adhesive was applied according to manufacturer’s instructions then Filtek LS was placed at the tested temperatures (n=6). Restorative procedures were done while the specimens were connected to IPP simulation. IPP was maintained and the specimens were immersed in artificial saliva at 37°C for 24h before testing. Each specimen was sectioned into sticks (0.9±0.01mm2). The sticks (24/group) were subjected to μTBS test and their modes of failure were determined using scanning electron microscope (SEM). For both preheated groups, IPT increased equally by 1.5–2°C upon application of the composite. After light curing, IPT increased by 4–5°C in all tested groups. Nevertheless, the IPT of the preheated groups required a longer time to return to the baseline temperature. One-way ANOVA revealed no significant difference between the μTBS values of all groups. SEM revealed predominately mixed mode of failure. Preheating of silorane-based resin composite increased the IPT but not to the critical level and had no effect on dentin μTBS.

Bond durability of different resin cements to caries-affected dentin under simulated intrapulpal pressure.

To evaluate the durability of the bond of different resin cement systems to normal dentin (ND) and caries-affected dentin (CAD) with and without simulated intrapulpal pressure (IPP). Molars with midcoronal caries were used. Occlusal enamel was cut to expose both dentin substrates (ND and CAD). Dentin substrates were differentiated using visual, tactile, caries-detecting dye, and dye-permeability methods. Prepared crown segments were equally divided according to the tested resin cement systems: etch-and-rinse resin cement, self-etch resin cement containing methacryloyloxydecyl dihydrogen phosphate (MDP), and self-adhesive resin cement. In addition to the dentin substrates and the resin cement types, the effect of application/storage conditions (with or without simulated IPP and with or without thermocycling) were tested. A microtensile bond strength test was done using a universal testing machine. Failure modes were determined using a scanning electron microscope. Etch-and-rinse resin cement strength values were significantly affected by the difference in the dentin substrates as well as the different application/storage conditions. Self-etch adhesive containing MDP bonded equally to ND and CAD and remained stable under all tested conditions. Self-adhesive resin cement revealed a similar bond to ND and CAD; however, its values were the lowest, especially when IPP and thermocycling were combined. Mixed failure was the predominant failure mode. Etch-and-rinse resin cement was sensitive to dentin substrate and application/storage conditions. Resin cement with self-etch adhesive containing MDP revealed more reliable bonding to ND/CAD even when IPP and thermocycling were combined. The bonding of the self-adhesive resin cement could not compete with other resin cements.

Influence of different intrapulpal pressure simulation liquids on the microtensile bond strength of adhesive systems to dentin.

To evaluate the effect of three different liquids used for intrapulpal pressure (IPP) simulation on the microtensile bond strength (µTBS) of three adhesive systems to dentin. The occlusal surfaces of sound human molars were ground flat down to mid-dentin depth. The teeth were bonded under 15 mmHg simulated IPP using distilled water, phosphate buffered saline, or human plasma as a simulating liquid. Three adhesive systems were tested: a single-bottle etch-and-rinse adhesive (SingleBond, 3M ESPE), and two single-step self-etching adhesives (G-Bond, GC) and (iBond, Heraeus Kulzer). Resin composite (Tetric EvoCeram, Ivoclar Vivadent) buildups were made in 2 increments, each 2 mm in height. Specimens were stored in artificial saliva under 20 mmHg IPP at 37°C for 24 h prior to testing. µTBS (n = 15) was tested using a universal testing machine, and failure modes were determined. Data were statistically analyzed using ANOVA and Bonferroni post-hoc tests at p <= 0.05. With SingleBond adhesive, distilled water showed significantly higher µTBS compared to plasma and phosphate buffered saline. With G-Bond, no significant difference was found between distilled water and phosphate buffered saline, whereas plasma showed significantly lower µTBS values. In contrast, no significant difference was encountered between the three IPP liquids for iBond adhesive. Predominant modes of failure were adhesive and mixed. A difference in intrapulpal pressure simulating liquids influences the bonding of adhesives to dentin. Etch-and-rinse adhesives are more sensitive to intrapulpal simulating liquids than are self-etching adhesives. Adhesives containing protein-coagulating components perform better with plasma perfusion than those lacking such components.

Bond Durability of Self-etch Adhesive to Ethanol-Based Chlorhexidine Pretreated Dentin after Storage in Artificial Saliva and under Intrapulpal Pressure Simulation

To evaluate the bond strength durability of a single-step self-etch adhesive to dentin pretreated with either ethanol-based chlorhexidine (ECHX) or water-based chlorhexidine (WCHX) after storage in artificial saliva and under intrapulpal pressure simulation (IPPS). The occlusal enamel of 30 freshly extracted premolars was trimmed to expose midcoronal dentin. Roots were sectioned to expose the pulp chamber. Specimens were distributed over three groups (n=10) according to the dentin pretreatment used. In the first group, Adper Easy One (3M ESPE) was applied to the dentin surfaces according to the manufacturer's instructions (control group). In the second group, dentin was pretreated before bonding with 1 mL of 2% CHX diacetate dissolved in 100% ethanol (ECHX). The third group received the same pretreatment; however, CHX was dissolved in distilled water (WCHX). Pretreatment and bonding were carried out while the specimens were subjected to IPPS. Resin composite (Valux Plus, 3MESPE) buildups were made. After curing, specimens were stored in artificial saliva and under IPPS at 37°C in a specially constructed incubator (n=5/group) either for 24 hours or six months prior to testing. Thereafter, bonded specimens were sectioned into sticks with a cross section of 0.9 ± 0.01 mm(2) and subjected to microtensile bond strength (μTBS) testing (n=25/subgroup) using a universal testing machine. Data were statistically analyzed using two-way analysis of variance (ANOVA) with repeated measures, one-way ANOVA , and Bonferroni post hoc tests (p≤0.05). Failure modes were determined using a scanning electron microscope. After 24 hours of storage, control and WCHX groups revealed significantly higher μTBS than the ECHX group. After six-month storage in artificial saliva and IPPS, only the WCHX group maintained its μTBS value. The predominant mode of failure was the mixed type, except for the ECHX group, which was mostly adhesive. Pretreatment of the dentin with ECHX had a negative effect on bonding of the tested single-step self-etch adhesive; however, WCHX showed bond stability under IPPS.

Bond Durability of Adhesives Containing Modified-monomer With/Without-fluoride After Aging in Artificial Saliva and Under Intrapulpal Pressure Simulation

To evaluate the dentin bond strength durability of adhesives containing modified-monomer with/without-fluoride after storage in artificial saliva and under intrapulpal pressure simulation (IPPS). The occlusal enamel of 48 freshly extracted teeth was trimmed to expose midcoronal dentin. Roots were sectioned to expose the pulp chamber and to connect the specimens to the pulpal-pressure assembly. Specimens were assigned into four groups (n=12) according to adhesive system utilized: a two-step etch-and-rinse adhesive system (SB, Adper Single Bond 2, 3M ESPE), a two-step self-etch adhesive system (CSE, Clearfil SE Bond, Kuraray Medical Inc), and two single-step self-etch adhesives with the same modified monomer (bis-acrylamide)-one with fluoride (AOF, AdheSE One F, Ivoclar-Vivadent) and the other without (AO, AdheSE One, Ivoclar-Vivadent). Bonding was carried out while the specimens were subjected to 15-mm Hg IPPS. Resin composite (Valux Plus, 3M ESPE) buildups were made. After curing, specimens were aged in artificial saliva and under 20-mm Hg IPPS at 37°C in a specially constructed incubator either for 24 hours or six months prior to testing. Bonded specimens (n=6/group) were sectioned into sticks (n=24/group) with a cross section of 0.9 ± 0.01 mm(2) and subjected to microtensile bond strength (μTBS) testing using a universal testing machine. Data were statistically analyzed using two-way analysis of variance (ANOVA) with repeated measures, one-way ANOVA tests, and a t-test (p<0.05). Failure modes were determined using a scanning electron microscope. The μTBS values of SB and CSE fell significantly after six-month storage in artificial saliva and under IPPS, yet these values remained significantly higher than those for the other two adhesives with modified monomers. There was no significant difference in the bond strength values between fluoride-containing and fluoride-free self-etch adhesive systems (AOF and AO) after 24 hours or six months. Modes of failure were mainly adhesive and mixed. Based on the results of this study, 1) Fluoride addition did not affect dentin bond durability; and 2) despite the fact that the single-step adhesive system with modified monomer showed stability, bond strengths associated with these systems remained lower than those of multistep adhesive systems.

Effect of re-etching oxalate-occluded dentin and enamel on bonding effectiveness of etch-and-rinse adhesives.

To determine whether or not re-etching of oxalate-treated dentin and enamel increases microshear bond strength (µSBS) and improves hybridization. Two single-bottle etch-and-rinse adhesives, SingleBond (3M/ESPE) and OptiBond S (Kerr), were bonded to deep occlusal dentin and enamel after perfusion under 20 mmHg simulated intrapulpal pressure. For each adhesive tested, the experimental groups were: G1: bonding according to manufacturer's instructions (control); G2: application of oxalate desensitizer (D/Sense Crystal, Centrix) to acid-etched substrate followed by 60 s water rinsing prior to bonding; G3: same as G2, but with a further 15-s re-etching with 35% phosphoric acid before bonding. The microshear bond strength (µSBS) to dentin and enamel was tested (n = 15); a scanning electron microscopic (SEM) analysis of surface topography (n = 2), interface (n = 2), and failure mode was also performed. The data were statistically analyzed using ANOVA and Tukey's tests at p ≤ 0.05. In enamel, both adhesives showed no significant difference in μSBS among groups. In dentin, the highest statistically μSBS for both adhesives was recorded for G1, followed by G2, with the lowest values revealed remnants of calcium oxalate crystals that were removed only from enamel surfaces after re-etching. SEM images of the interface revealed inadequate dentin hybridization in G2 and G3 compared to G1. Re-etching after oxalate treatment compromises bonding of single-bottle etch-and-rinse adhesives to dentin and provides no added benefits to enamel bonding.

Effect of Chlorhexidine Pretreatment on Bond Strength Durability of Caries–affected Dentin Over 2-Year Aging in Artificial Saliva and Under Simulated Intrapulpal Pressure

To evaluate the influence of 2% and 5% chlorhexidine (CHX) pretreatment on bond durability of a self-etching adhesive to normal (ND) and caries-affected (AD) dentin after 2-years of aging in artificial saliva and under simulated intrapulpal pressure (IPP). One hundred twenty freshly extracted carious teeth were ground to expose ND and AD. Specimens were distributed into three equal groups (n=40) according to whether the dentin substrates were pretreated with 2% or 5% CHX or with water (control). Clearfil SE Bond (Kuraray) was applied to both substrates and composite cylinders (0.9 mm diameter and 0.7 mm height) were formed. Pretreatment and bonding were done while the specimens were subjected to 15 mm Hg IPP. After curing, specimens were aged in artificial saliva at 37°C and under IPP at 20 mm Hg until being tested after 24 hours or 2 years (n=20/group). Microshear bond strength was evaluated. Failure modes were determined using a scanning electron microscope (SEM) at 400× magnification. Data were statistically analyzed using three-way analysis of variance (ANOVA); one-way ANOVA tests, and t-test (p<0.05). Additional specimens (n=5/group) were prepared to evaluate interfacial silver precipitation. For the 24-hour groups, there were no significant differences among the ND groups and AD groups. For ND aged specimens, the 5% CHX group had the highest value followed by the 2% CHX and control groups, although the difference was statistically insignificant. For AD aged specimens, the 5% CHX group revealed statistically higher bond values compared to the 2% CHX and control groups. Fracture modes were predominately adhesive and mixed. Different interfacial silver depositions were recorded. Two percent or 5% CHX pretreatment has no adverse effect on the 24-hour bonding to ND and AD. Five percent CHX was able to diminish the loss in bonding to AD after 2years of aging in artificial saliva and under simulated IPP.

Influence of intrapulpal pressure simulation on the bond strength of adhesive systems to dentin

The purpose of this study was to evaluate the influence of intrapulpal pressure simulation on the bonding effectiveness of etch & rinse and self-etch adhesives to dentin. Eighty sound human molars were distributed into eight groups, according to the permeability level of each sample, measured by an apparatus to assess hydraulic conductance (Lp). Thus, a similar mean permeability was achieved in each group. Three etch & rinse adhesives (Prime & Bond NT - PB, Single Bond -SB, and Excite--EX) and one self-etch system (Clearfil SE Bond--SE) were employed, varying the presence or absence of an intrapulpal pressure (IPP) simulation of 15 cmH2O. After adhesive and restorative procedures were carried out, the samples were stored in distilled water for 24 hours at 37 degrees C, and taken for tensile bond strength (TBS) testing. Fracture analysis was performed using a light microscope at 40 X magnification. The data, obtained in MPa, were then submitted to the Kruskal-Wallis test ( a = 0.05). The results revealed that the TBS of SB and EX was significantly reduced under IPP simulation, differing from the TBS of PB and SE. Moreover, SE obtained the highest bond strength values in the presence of IPP. It could be concluded that IPP simulation can influence the bond strength of certain adhesive systems to dentin and should be considered when in vitro studies are conducted.

Effect of dentin conditioning on dentin permeability and micro‐shear bond strength

The purpose of this study was to compare fluid flow rates across dentin surfaces treated with four conditioners. The effect of conditioning on the micro-shear bond strengths of glass ionomer cement (Fuji IX GP) and resin-based adhesives (Single Bond 2 or Clearfil SE Bond) were also investigated. Under a simulated pressure of 1.3 kPa, two dentin conditioners, phosphoric acid, and a self-etching primer were applied to the dentin surfaces. Dentinal fluid flows at baseline and after conditioning were recorded for 15 min each. The conditioned surfaces were examined using a scanning electron microscope. The micro-shear bond strengths of the glass ionomer cement and of the resin-based adhesives bonded to conditioned dentin surfaces were evaluated while simulated intrapulpal pressure was maintained at 0 or 1.3 kPa. Only the dentin surface etched with phosphoric acid showed a significant increase in permeability. Micro-shear bond strengths of Fuji IX GP were not affected by conditioning the dentin surfaces or by bonding at different intrapulpal pressures (0 or 1.3 kPa). The effects on bond strengths of resin-based adhesives depended on the system used. The simulated positive intrapulpal pressure during bonding significantly affected the adherence of Single Bond 2, whereas Clearfil SE Bond was unaffected.

Adhesive performance of dentin bonding agents applied in vivo and in vitro. Effect of intrapulpal pressure and dentin depth

The purpose of this study was to evaluate the influence of intrapulpal pressure and dentin depth on bond strengths of an etch-and-rinse and a self-etching bonding agent to dentin in vitro and in vivo. Twenty-four pairs of premolars were randomly divided into four groups (n = 6) according to the dentin bonding agent, Single Bond and Clearfil SE Bond, and intrapulpal pressure, null or positive. Each tooth of the pair was further designated to be treated in vivo or in vitro. The intrapulpal pressure was controlled in vivo by the delivery of local anesthetics containing or not a vasoconstrictor, while in vitro, it was achieved by keeping the teeth under hydrostatic pressure. Class I cavities were prepared and the dentin bonding agents were applied followed by incremental resin restoration. For the teeth treated in vitro, the same restorative procedures were performed after a 6 month-storage period. Beams with 1 mm(2) cross-sectional area were prepared and microtensile tested. Clearfil SE Bond was not influenced by any of the variables of the study, while bond strengths produced in vitro were significantly higher for Single Bond. Overall, lower bond strengths were produced in deep dentin, which reached statistical significance when Single Bond was applied under physiological or simulated intrapulpal pressure. In conclusion, in vitro bonding may overestimate the immediate adhesive performance of more technique-sensitive dentin bonding systems. The impact of intrapulpal pressure on bond strength seems to be more adhesive dependent than dentin morphological characteristics related to depth.

The effect of simulated intrapulpal pressure on bond strength to enamel and dentine.

The purpose of this study was to evaluate the effect of simulated intrapulpal pressure on the shear bond strength (SBS) of a self-etching bonding system (Clearfil Liner Bond II) to both enamel and dentine surfaces. Forty-two caries-free human molar teeth were randomly assigned to two equal groups (n=21). One group of 21 teeth was connected to a special pulpal pressure machine, which is developed to simulate in vivo conditions. The buccal and lingual surfaces of the teeth were prepared with a diamond wheel to create flat dentine and enamel surfaces. A self-etching bonding system was then applied under pulpal pressure and 2.5 mm diameter composite cylinders were bonded to the prepared surfaces. The samples were then stored in distilled water at room temperature for 24 h under pulpal pressure before SBS was tested. The second restored group was used as a control and the teeth were not connected to the pulpal pressure apparatus during material application and test procedures. They were stored for 24 h in distilled water at room temperature before the SBS test. Fracture analysis of the enamel and dentinal surfaces was performed using a stereomicroscope. Shear bond strength values to dentine was significantly reduced with pulpal pressure (P < 0.001). However, in the enamel, SBS was increased (P < 0.001). In the control group, the SBS values to dentine and enamel did not show any significant difference (P > 0.05). Based on these results, it can be concluded that further analysis of enamel histology and bonding mechanisms are needed.