Intraparticle Diffusion Model Research Articles

Kinetic and Mechanistic Modelling of Pyrimethanil Fungicide Adsorption onto Soils of Varying Physico-chemical Properties.

Pesticide transport in the environment is impacted by the kinetics of its adsorption onto soil. The adsorption kinetics of pyrimethanil was investigated in ten soil samples of varying physicochemical properties. The highest adsorption was in the soil having the maximum silt and CaCO3 contents, pH and electrical conductance but the lowest amorphous Fe oxides and CaCl2 extractable Mn. Pseudo-second order kinetics and intra-particle diffusion model best accounted the adsorption kinetics of pyrimethanil. The equilibrium adsorption estimated by pseudo-second order kinetics (q02) was significantly and positively correlated with CaCl2 extractable Cu content (r = 0.709) while rate coefficient (k02) had a negative correlation with crystalline iron oxides content (r = -0.675). The intra-particle diffusion coefficient (ki.d.) had inverse relationship with CaCl2 extractable Mn content in soils (r = -0.689). FTIR spectra showed a significant interaction of pyrimethanil with micronutrient cations. Adsorption kinetic parameters of pyrimethanil could be successfully predicted by soil properties. The findings may help to evolve fungicide management decisions.

Synthesis and characterisation of novel beta-cyclodextrin based Fe3O4 nanocomposite: adsorption behaviour and photocatalytic dye degradation studies

ABSTRACT Novel Beta-Cyclodextrin-based Fe3O4 nanocomposite has been synthesised through copolymerisation by incorporating Fe3O4 nanoparticles into the polymer matrix. Ultraviolet-Visible (UV-Visible) spectroscopy, Fourier transform infrared (FTIR) spectroscopy, Thermogravimetric (TGA) analysis, Point of Zero Charge, X-ray diffraction (XRD), and Scanning electron microscopy (SEM) analysis have been used to characterise the Fe3O4 Nanoparticles and β-CDHs@Fe3O4 nanocomposite. The synthesised β-CDHs@Fe3O4 nanocomposite has been utilised for the adsorption of methylene blue (MB) dye from aqueous solutions. The maximum percentage removal of MB dye at optimum pH 7 and was found to be 98.51%. The adsorption capacity (qe) of β-CDHs@Fe3O4 nanocomposite has been found to be 268.09 mg/g at optimum dosages 1.2 g/L, pH 7, temperature 25°C, concentration 100 mg/L and an agitation speed of 200 rpm. Adsorption data have been fitted with three isotherm models namely Langmuir, Freundlich, and Temkin, and it was found to be the best fit with the Langmuir isotherm model. Kinetic studies like the pseudo-first order, pseudo-second order, and intra-particle diffusion model were also performed to study the adsorption mechanism. Further, thermodynamic studies demonstrate that the reaction was exothermic and spontaneous. Photocatalytic degradation of MB dye under visible light has also been studied, and 79.01% degradation of the dye was observed. Also, desorption of the nanocomposite was performed, and it was found to be reusable up to 5 times with 90% dye-desorption in the fifth cycle.

Adsorptive removal of oxytetracycline antibiotics on magnetic nanoparticles NiFe2O4/Au: Characteristics, mechanism and theoretical calculations

This investigation aims to develop a specialized adsorbent for the efficient removal of Oxytetracycline (OTC) from complex matrices. We employed a magnetic composite, NiFe2O4/Au (NFO/Au), as the adsorbent, which exhibited remarkable ease of material recovery due to the reasonable magnetic property of NFO. Simultaneously, gold nanoparticles (AuNPs) on the NFO surface amplified the material's adsorption capacity by demonstrating a strong affinity for the amine groups within the OTC structure. The crystal and morphological structure and surface chemistry of the prepared material were identified by XRD, TEM, BET, and XPS. Their magnetic and optical properties were studied by VSM and UV-VIS. Cubic or rectangular shapes (50–100 nm) of NFO were surrounded by spherical AuNPs (10–30 nm). The saturation magnetization slightly decreased from 33 emu/g to 30 emu/g upon coating the NFO surface with AuNPs, which still ensures good magnetism of the composite. A maximum adsorption capacity of 43.48 mg/g was achieved at optimum adsorption conditions. The novel adsorbent exhibits fast adsorption after 30 min, high adsorption capacity, and good reusability after five cycles. The adsorption equilibrium adhered to a monolayer Langmuir isotherm, while the adsorption kinetics followed pseudo-second-order kinetics and the intraparticle diffusion models. The first principle calculation based on the density functional theory revealed that the fundamental reason behind the enhanced adsorption capacity is through greater electron populations, more negative binding energy, and higher effective charge transfer. This composite material was employed to remove OTC from water samples taken from a shrimp pond, demonstrating an impressive adsorption efficiency of approximately 90 %.

Olive leaf extract-assisted preparation of nanoferrite for adsorptive removal of cationic dye

In this work, magnetic Fe3O4 nanoparticles synthesized with olive leaf extract were used to investigate the adsorption of Basic violet 16 from aqueous solutions. The physicochemical characteristics of Fe3O4 nanoparticles were evaluated by DLS, zeta potential, XRD, FTIR SEM, EDX, N2 adsorption-desorption, TEM, and VSM analyses. Using DLS analysis, the average size of the Fe3O4 nanoparticles was found to be 231.2 nm. Zeta potential studies indicated that the synthesized nanoparticles were moderately stable, and zeta potential was calculated as −14.9 mV. According to TEM analysis, the synthesized nanoparticles ranged in size from 6.28 to 17.3 nm. The optimum parameters for the adsorption of basic violet 16 with Fe3O4 nanoparticles were determined as pH: 9.0, adsorbent dose: 0.8 g, contact time: 210 min, stirring speed: 250 rpm. Langmuir, Freundlich, Dubinin Radushkevich (D-R) and Temkin isotherm models were used to characterize the basic violet 16 sorption data onto Fe3O4 nanoparticles and it was seen that Basic violet 16 adsorption onto the Fe3O4 nanoparticles followed Langmuir isotherm model at all temperatures. The maximum adsorption capacity of Basic violet 16 with Fe3O4 nanoparticles was determined as 117.64 mg/g at 318 K. Pseudo-first-order, pseudo-second-order and intraparticle diffusion models were used to describe the adsorption kinetics at 298–318 K. The adsorption followed the pseudo-second-order kinetic model. Adsorption of Basic violet 16 onto Fe3O4 nanoparticles occurred spontaneously and endothermically. Characteristic peaks Fe3O4 nanoparticles were visible in the XRD analysis. The SBET surface area dropped from 110.42 m2/g to 91.27 m2/g after dye adsorption. Peaks in the FTIR analysis showed that Basic violet 16 had been successfully adsorbed on Fe3O4 nanoparticles.

Enhancing irrigation water quality efficiently with potassium feldspar-derived adsorbent: Heavy metal detoxification and nutrient augmentation

The pollution of Pb2+ and Cd2+ in both irrigation water and soil, coupled with the scarcity of vital mineral nutrition, poses a significant hazard to the security and quality of agricultural products. An economical potassium feldspar-derived adsorbent (PFDA) was synthesized using potassium feldspar as the main raw material through ball milling-thermal activation technology to solve this problem. The synthesis process is cost-effective and the resulting adsorbent demonstrates high efficiency in removing Pb2+ and Cd2+ from water. The removal process is endothermic, spontaneous, and stochastic, and follows the quasi-second-order kinetics, intraparticle diffusion, and Langmuir model. The adsorption and elimination of Pb2+ and Cd2+ is largely dependent on monolayer chemical sorption. The maximum removal capacity of PFDA for Pb2+ and Cd2+ at room temperature is 417 and 56.3 mg·g−1, respectively, which is superior to most mineral-based adsorbents. The desorption of Pb2+/Cd2+ on PFDA is highly challenging at pH≥3, whereas PFDA and Pb2+/Cd2+ are recyclable at pH≤0.5. When Pb2+ and Cd2+ coexisted, Pb2+ was preferentially removed by PFDA. In the case of single adsorption, Pb2+ was mainly adsorbed onto PFDA as Pb2SiO4, PbSiO3·xH2O, Pb3SiO5, PbAl2O4, PbAl2SiO6, PbAl2Si2O8, Pb2SO5, and PbSO4, whereas Cd2+ was primarily adsorbed as CdSiO3, Cd2SiO4, and Cd3Al2Si3O12. After the complex adsorption, the main products were PbSiO3·xH2O, PbAl2Si2O8, Pb2SiO4, Pb4Al2Si2O11, Pb5SiO7, PbSO4, CdSiO3, and Cd3Al2Si3O12. The forms of mineral nutrients in single and complex adsorption were different. The main mechanisms by which PFDA removed Pb2+ and Cd2+ were chemical precipitation, complexation, electrostatic attraction, and ion exchange. In irrigation water, the elimination efficiencies of Pb2+ and Cd2+ by PFDA within 10 min were 96.0 % and 70.3 %, respectively, and the concentrations of K+, Si4+, Ca2+, and Mg2+ increased by 14.0 %, 12.4 %, 55.7 %, and 878 %, respectively, within 60 min. PFDA holds great potential to replace costly methods for treating heavy metal pollution and nutrient deficiency in irrigation water, offering a sustainable, cost-effective solution and paving a new way for the comprehensive utilization of potassium feldspar.

Synergistic adsorption of methylene blue using ternary composite of phosphoric acid geopolymer, calcium alginate, and sodium lauryl sulfate.

The removal of dyes from the aquatic ecosystem is necessary being a major threat to life. For enhanced remediation of methylene blue (MB) dye, a new ternary biopolymer-geopolymer-surfactant composite adsorbent is synthesized by combining phosphoric acid geopolymer (PAGP), calcium alginate (Alg), and sodium lauryl sulfate (SLS). During the synthesis of the composites, PAGP and SLS were mixed with the alginate matrix, producing porous hybrid beads. The PAGP-SLS-alginate (PSA) beads prepared were characterized using different analytical tools, i.e., scanning electron microscopy (SEM), Fourier transform infrared spectrophotometry (FTIR), X-ray diffractometry (XRD), surface area and porosimetery (SAP), and thermogravimetric analysis (TGA). To ascertain the ideal conditions for the adsorption process, a batch reactor procedure was used to investigate the effects of several parameters on MB adsorption, including pH (2, 4, 6, 8, 10), PSA adsorbent dosage (0.06-0.12 g), MB concentration (50-500 mg/L), contact time (15 to 300 min), and temperature (25, 35, and 45 °C). The SEM investigation indicated that ~ 1860 μm-sized PSA beads with 6-8 μm voids are generated. Based on XRD, FTIR, and SAP examinations, the material is amorphous, having numerous functional groups and an average pore size of 6.42 nm. Variation of pH has a little effect on the adsorption process, and the pH of 7.44 was found to be the pHpzc of the PSA beads. According to the findings of the batch study, equilibrium adsorption was obtained in 270-300 min, showing that the adsorption process was moderately slow-moving and effective. The dye adsorption linearly increased with initial dye concentration over concentration range of 50-500 mg/L and reciprocally decreased with rise in temperature. 0.06 g adsorbent dose, 25 °C, pH10, and 270 min were found to be the better conditions for adsorption experiments. Langmuir isotherm fitted well compared to Freundlich, Temkin, and Dubinin-Radushkevich (DR) isotherm models on the experimental data, and the maximum adsorption capacity(qmax) calculated was 1666.6 mg. g-1. Pseudo-second-order (PSO) kinetics model and multi steps (two) intra particle diffusion (IPD) model fitted well on the adsorption kinetics data. The system's entropy, Gibbs free energy, and change in enthalpy were measured and found to be -109.171 J. mol-1. K-1, - 8.198 to - 6.014 kJ. mol-1, and - 40.747 kJ. mol-1. Thermodynamics study revealed that adsorption process is exothermic, energetically favorable and resulting in the decrease in randomness. Chemisorption is found to be the dominant mechanism as confirmed by pH effect, Langmuir isotherm, PSO kinetics, IPD model, and thermodynamics parameters. PSA beads were successfully regenerated using ethanol in a course of 120 min and re-used for five times. To sum up, the PSA adsorbent's impressive adsorption capability of 1666.66 mg/g highlights its potential as a successful solution for methylene blue removal. The results of this study add to the expanding corpus of information on sophisticated adsorption materials and demonstrate PSA's potential for real-world uses in wastewater treatment and environmental clean-up.

Reduction of organic contaminants from industrial effluent using the advanced oxidation process, chemical coagulation, and green nanotechnology

Municipal wastewater treatment systems use the chemical oxygen demand test (COD) to identify organic contaminants in industrial effluents that impede treatment due to their high concentration. This study reduced the COD levels in tannery wastewater using a multistage treatment process that included Fenton oxidation, chemical coagulation, and nanotechnology based on a synthetic soluble COD standard solution. At an acidic pH of 5, Fenton oxidation reduces the COD concentration by approximately 79%. It achieves this by combining 10 mL/L of H2O2 and 0.1 g/L of FeCl2. Furthermore, the author selected the FeCl3 coagulant for the coagulation process based on the best results of comparisons between different coagulants. At pH 8.5, the coagulation dose of 0.15 g/L achieved the maximum COD removal efficiency of approximately 56.7%. Finally, nano bimetallic Fe/Cu was used to complete the degradation and adsorption of the remaining organic pollutants. The XRD, SEM, and EDX analyses proved the formation of Fe/Cu nanoparticles. A dose of 0.09 g/L Fe/Cu NPs, 30 min of contact time, and a stirring rate of 200 rpm achieve a maximum removal efficiency of about 93% of COD at pH 7.5. The kinetics studies were analyzed using pseudo-first-order P.F.O., pseudo-second-order P.S.O., and intraparticle diffusion models. The P.S.O. showed the best fit among the kinetic models, with an R2 of 0.998. Finally, the authors recommended that technique for highly contaminated industrial effluents treatment for agriculture or industrial purposes.

Zinc oxide nanoparticles encapsulated in alginate beads: a promising and recyclable adsorbent for simultaneous uptake of toxic metals

Heavy metal toxicity is a known problem and various methods are used for treatment. Adsorption has some advantages and it would be promising if environmentally friendly and cheap materials were utilized. Alginate and zinc oxide nanoparticles were selected and composite alginate beads were used for the removal of mixed metals from aqueous solutions. Batch and column experiments were conducted to determine some parameters’ effects and the adsorbent’s real application potential. According to the batch experiments, zinc oxide nanoparticles to alginate ratio of 0.5 g g−1, and pH levels nearby to the neutral range led to better metal removals. 0.5 ml min−1 of flow rate supplied better metal removal efficiencies in columns, with the highest treatment as 86% of Pb2+. Acid treatment can be successfully applied for the regeneration of the adsorbent, at least three times only with a 4% reduction in the adsorption efficiency. Heavy metal uptake was compatible with the pseudo 2nd order model indicating chemisorption as a dominant mechanism. Also, the intraparticle diffusion model illustrated adsorption might govern more than one step. The Langmuir model had the best fit and suggested monolayer covering for Pb2+, 76.3 mg g−1. Alginate-based nanocomposite beads were useful for mixed metal removal and could be used.

The valorization of Prunus mahaleb shell through acid modification for the sorption of Pb2+ removal from aqueous solution

AbstractThis study aimed to investigate the biosorption performance of acid-modified waste Prunus mahaleb (PMA) shells in the removal of Pb2+ ions from aqueous solutions. Changes in the morphological properties and functional components of PMA biosorbent were characterized using SEM–EDX, FT-IR, BET, and PZC analyses. The effect of various parameters such as initial Pb2+ concentration, pH, PMA dosage, contact time, and temperature on biosorption was investigated using a batch biosorption procedure. The maximum biosorption capacity, determined using the Langmuir isotherm, was calculated to be 119 mg g−1. It was found that the biosorption kinetic mechanism followed pseudo-second-order kinetics and intraparticle diffusion model. According to the determined thermodynamic parameters, the biosorption mechanism was found to be endothermic (ΔH° > 0), spontaneous (ΔS° > 0), and entropy-increasing (ΔG° < 0). The outcomes of the experiment were evaluated in comparison to other sorbents that have been previously commonly used in the literature. It was demonstrated that PMA could be a promising, environmentally friendly, cost-effective, and sustainable potential biosorbent for the removal of Pb2+ ions.

Investigation of effectiveness of KOH-activated olive pomace biochar for efficient direct air capture of CO2

The capture of CO2 directly from the air is one of the most promising methods under investigation in recent years to reduce the environmental concentration of this pollutant in order to mitigate its effects on climate change. In this work, the activation of olive pomace biochar with potassium hydroxide, KOH, has been studied for its use as a CO2 adsorbent. The effectiveness of biochar activated with KOH at 750 °C in an inert N2 atmosphere was evaluated, using different mass ratios of biochar/KOH, 1:0.5, 1:1, and 1:2. Various characterisation analyses of the biochar were performed to determine its chemical composition, specific surface area, pore size and volume, structure, morphology, and functional groups. The adsorption isotherm was determined at atmospheric pressure and a temperature of 10 °C. The experimental equilibrium results were fitted to the Langmuir, Freundlich, and Temkin models. Additionally, the kinetic behavior of biochar/KOH as an adsorbent was studied, and dynamic experiments were conducted at atmospheric pressure and 10 °C. The experimental data were fitted to various kinetic models (pseudo-first order, pseudo-second order, Avrami, and Elovich). Furthermore, the mass transfer mechanism during the adsorption process was evaluated using the intra-particle diffusion model. Finally, biochar regeneration was investigated for its subsequent reuse as an adsorbent. For this purpose, complete desorption of the captured CO2 in the biochar was easily carried out by modifying the temperature.

Design and development of rare earth elements anchored pectin/chitosan integrated magnesia hybrid composite for effective defluoridation of water

Fluoride pollution in drinking water is a worldwide concern arises from natural and human actions. The excessive fluoride present in drinking water leads to fluorosis. In this study, dual polysaccharide biopolymers namely pectin and chitosan were incorporated with magnesia followed by imprinted with lanthanum and cerium ions gives PCML (pectin/chitosan/magnesia/lanthanum) and PCMC (pectin/chitosan/magnesia/cerium) hybrid materials for fluoride adsorption investigation. The enhanced defluoridation capacities (DCs) of PCML and PCMC composites were seen as 4.976 and 4.972 mg g−1 by 30 min individually. To decide the impact of various affecting parameters viz., dosage, initial fluoride concentration, pH, contact time and challenging anions were examined in batch method. The pH results show the utmost DCs of PCML and PCMC composites was noted at pH 6 and in co-ions experiments, the significant competition found with bicarbonate ion owing to the superior electronic building of bicarbonate ion. The defluoridation equilibrium data of PCML and PCMC composites follows Langmuir, pseudo-second-order and intraparticle diffusion models. The positive ΔH° value as 3.04 kJ mol−1 for PCML composite and 2.88 kJ mol−1 for PCMC composite were exposed that the endothermic nature of fluoride adsorption occurs onto PCML and PCMC composites. The defluoridation mechanism of PCML and PCMC composites were attained by complexation, ion-exchange and electrostatic interaction. The reusability results shows that the synthesized PCML and PCMC composites can be reused upto six cycles. Field trail result demonstrates the synthesized PCML and PCMC composites were applicable at field conditions by reducing fluoride concentration below 1.5 mg/L.

Hydrophobic hypercrosslinked polymers prepared by secondary pore-forming method as excellent toluene adsorbents

In this work, inspired by molecular imprinting technology, we developed a secondary pore-forming method to chemically etch three hypercrosslinked polymers which are constructed from three novel hexapolar monomers containing imine groups, resulting in three novel hydrophobic porous hyper-crosslinked polymers (HCPs) pGly-TPA, pP-TPA and pBP-TPA. The structures were determined by FT-IR and solid-state 13C NMR spectroscopic techniques. The specific surface areas of pGly-TPA, pP-TPA and pBP-TPA are 694.1, 197.9 and 497.7 m2/g, respectively. All three porous polymers exhibit high hydrophobic properties with wetting angles of much greater than 90°. The breakthrough adsorption experiments revealed that the three prepared polymers exhibited significant adsorption capacity for toluene (322.05 mg/g for pGly-TPA, 114.43 mg/g for pP-TPA and 279.14 mg/g for pBP-TPA), but showed almost no adsorption for ethyl acetate, cyclohexane, and n-hexane, exhibiting certain molecular size and polarity selectivity. The adsorption behaviors of toluene on pGly-TPA, pP-TPA and pBP-TPA can be fit by the Boltzmann model and the Yoon-Nelson model, suggesting that the fixed bed has low mass transfer resistance. The adsorption rate is controlled by both external diffusion and intraparticle diffusion, as shown by the intraparticle diffusion model analysis. In addition, the adsorption capacity of toluene on pGly-TPA is almost unchanged under high humidity (70 %) or five adsorption–desorption processes, which demonstrates exceptional water-resistance and stability. This work is a reference for preparing novel hydrophobic HCPs using the secondary pore-forming method for removing VOCs from humid air.

Photocatalytic degradation of Direct Black 10 B dye in aqueous phase using nanophotocatalyst

ABSTRACT In this study, the photocatalytic degradation of an aqueous solution containing a mixture of Direct Black 10 B dye using titanium dioxide (TiO2) as a catalyst was investigated. The degradation of Direct Black 10 B dye was studied for several parameters, including the catalyst, dosage, initial concentration of dye, and pH. Variable catalyst quantities (0.25, 0.50, 0.75, 1, and 1.25 g), pH (3, 5, 9, and 11), and beginning dye concentration were used in the studies (62.5, 125, 250 and 500 ppm). 0.75 g/litre of catalyst was found to be the ideal dose. The ideal catalyst concentration was determined to be 0.75 g/litre, and the maximal dye decolourization rate was further studied in a basic media, i.e. at pH 9 Blue turned into grey and finally white in the acidic medium, whereas blue turned into pink and then white in the basic medium. After 3 hours 98% of the colour was completely removed at this optimal point. The Langmuir, Freundlich and Temkin isotherms were examined. The langmuier isothers with regression coefficient 0.99 is best fitted as compared to Freundlich and Temkin isotherms. The findings of the kinetic analysis suggest that the Pseudo Second order with regression coefficient 0.9923 is best suited as compared with the pseudo first order and Intra-particle diffusion model.

Hydrothermally Produced Activated Carbon Impregnated with ZnO for the Adsorptive Removal of Toxic Pharmaceutical Contaminants from Aqueous Solution

This research explores the adsorption (AD) of diclofenac sodium (DS) onto a Hydrothermally produced activated carbon impregnated with ZnO (HTC-AC/ZnO) surface, considering various factors such as initial concentration (IC), adsorbent dose, contact time, and pH. The characterization of HTC-AC/ZnO was performed using X-ray diffractometer (XRD), scanning electron microscope (SEM), Fourier-transform infrared spectroscopy (FTIR), and nitrogen physisorption spectroscopy (BET). Tests were conducted with different adsorbent doses (0.5–4 g/L) at 303 K and various initial diclofenac concentrations (ranging from 50 mg/L to 250 mg/L) to observe their effects. Additionally, pH values were altered from 2 to 12 to study their influence on AD. Kinetic studies, thermodynamic studies, and AD isotherm models were examined. The Temkin isotherm model (TIM) was found to be the most accurate for DS-AD on HTC-AC/ZnO. For DS-AD on HTC-AC/ZnO, pseudo-first-order models (PFOM), intraparticle diffusion model (IPDM), and pseudo-second-order models (PSOM) were applied, with a correlation coefficient of 0.945, indicating a good fit for PFOM. The kinetics suggested rapid adsorption. Notably, the HTC-AC/ZnO composite exhibited consistent AD characteristics across four consecutive cycles, with a removal efficiency exceeding 99.38%. This suggests that HTC-AC/ZnO is an appropriate and economically viable adsorbent for the elimination of DS from water-based solutions. The investigation provides compelling evidence that HTC-AC/ZnO is a viable adsorbent for the effective elimination of DS from water sources.

The Effectiveness of Carbonized Neem Leaves Adsorbent for the Removal of Phenol from Synthesized Effluent Using the Batch Process Method

The adsorption of phenol in aqueous solution was investigated using carbonized neem leaves adsorbents. The effect of various factors such as contact time, phenol concentration, pH, temperature, and amount of adsorbent on the adsorption capacity of the adsorbents was determined. The results show that maximum adsorption was obtained at a contact time of 150 minutes, at a phenol concentration of 50 mg/L, optimum adsorption temperature of 45⁰C, pH of 2 and adsorbent dosage of 3 g/L. The equilibrium data was well described by the Freundlich isotherm equation (R2= 0.955 ). This shows a heterogenous adsorption process. The kinetics of the process were explained by the intra-particle diffusion models (R2>0.9). This fitted data indicates a degree of boundary layer control and is not limited to intra-particle diffusion.

Revealing the contribution of Cu(II) and Cu(I) inherent in MOF-199 for efficient thiophene removal at room temperature

Thiophene (C4H4S) removal from coke oven gas is critical to its subsequent high valuable utilization but remains a challenge. MOF-199 was considered as a promising candidate for C4H4S adsorption removal owing to its nature of enriched opened Cu sites. However, the presence of mixed valence of Cu(II) and Cu(I) in MOF-199 makes it puzzling to their respective contribution to the removal of C4H4S. Herein, a series of MOF-199 with different Cu(I) contents were synthesized using different methods, including hydrothermal, solution diffusion, and ultrasonic, and their C4H4S adsorption performance were investigated. The respective contributions of Cu(II) and Cu(I) to the C4H4S removal was systematically discussed. The collected results indicated that although the samples prepared with different methods present a remarkable difference in textural characters, the latter was found to have a negligible influence on the C4H4S removal owing to MOF-199(H) affording an inferior surface area and pore volumes but performing the best C4H4S removal capacity of 53.7 mg S/g. The co-adsorption results of CH3SCH3 and C4H4S indicated that the excellent performance of MOF-199(H) mainly attributed to the presence of Cu(I), which provides active sites for C4H4S adsorption through π complex coordination. Cu(II) species was also found to the C4H4S adsorption via soft-acid-base coordinated interaction, but its contribution is 8.3 mg S/g, only accounting for 15.5 %. Additionally, the adsorption of C4H4S on MOF-199(H) was found to follow the intra-particle diffusion model and the Langmuir models. Moreover, MOF-199(H) also exhibited an excellent regeneration performance due to the weak interaction between C4H4S and their opened Cu sites, the C4H4S adsorption capacity still reaches 50.6 mg S/g after three regeneration cycles, about 94 % of its initial value. The results collected in this study will provide new insights for the manipulation of performance of C4H4S adsorption on the MOF-199.

Diclofenac sodium adsorption in aqueous media by activated carbon obtained from einkorn (Triticum monococcum L.) husk

AbstractThe uncontrolled release of waste diclofenac with low biodegradability is considered to be a potential threat for the environment and creatures. To find effective solution for this issue, this study reports the adsorption performance of diclofenac sodium salt (DCF) by using activated carbon (EHAC) obtained from einkorn (Triticum monococcum L.) husk in aqueous solution under various circumstances. It was found that DCF adsorption on EHAC was highly solution pH dependent, and DCF adsorption by EHAC decreased with increasing adsorption temperature. Equilibrium data showed that fitted isotherm model with the experiment results of DCF adsorption on EHAC followed the order of Langmuir > Temkin > Freundlich > Dubinin-Radushkevich. Adsorption capacity of EHAC for DCF adsorption in aqueous solution was calculated to be 147.06 mg/g at 25 °C. The adsorption kinetic of DCF adsorption on EHAC was determined to obey the pseudo-second-order kinetic model. By utilizing FTIR and pH data obtained from DCF adsorption on EHAC, DCF adsorption mechanisms with some interactions such as π-π stacking, electrostatic interactions, and hydrogen bonding were suggested at diverse pH values. Additionally, intraparticle diffusion model was applied to kinetic results to further recognize the kinetic mechanism of DCF adsorption on EHAC. Furthermore, thermodynamic parameters for DCF adsorption on EHAC were calculated and evaluated, in which DCF adsorption process by EHAC was determined to be exothermic, spontaneous, and feasible.

Synthesis of MgZnAl Layered Triple Hydroxide Nanoplates as an Efficient Adsorbent for Removing the Acid Yellow 76 Azo Dye

AbstractA simple hydrothermal method was employed for synthesizing MgZnAl layered triple hydroxide nanoplates (MgZnAl LTH) as an efficient adsorbent for removing the Acid Yellow 76 (AY76) azo dye. A batch process was used to perform adsorptions were and investigate the effects of experimental parameters including temperature, adsorbent dosage, solution pH. The best adsorption conditions obtained were pH of 4, MgZnAl LTH dosage of 20 mg and temperature of 55 °C. The kinetics of adsorption was studied using pseudo‐first‐order, pseudo‐second‐order, Elovich, and intraparticle diffusion models. To obtain equilibrium absorption data, Freundlich, Langmuir, and Temkin isotherms were utilized. The findings showed that the adsorption data based on the experiment had a good agreement with the Freundlich model. The highest capacity of adsorption equal to 277.8 mg/g was obtained for the MgZnAl LTH nanoplates toward AY76. Thermodynamic results showed that the process of adsorption of AY76 onto MgZnAl LTH nanoplates had a spontaneous and endothermic nature.

Phosphate adsorption on dried alum sludge: Modeling and application to treatment of dairy effluents

This study evaluates Alum sludge from drinking water treatment plants for the efficient and cost-effective removal of phosphates from aqueous solutions. Extensive characterization and batch experiments have established that optimal phosphate removal was achieved with a sludge dosage of 20 g L−1 (at an initial phosphate concentration of 100 mg L−1), a pH of 5, a temperature of 23 °C, and a stirring speed of 200 rpm. These conditions significantly reduced phosphate levels, ensuring compliance with legal discharge limits. The Langmuir isotherm, pseudo-second-order kinetic and intraparticle diffusion models best described the adsorption process, highlighting the spontaneous and endothermic nature of the phenomenon. The sludge effectively reduced phosphate concentrations to acceptable levels when applied to dairy effluents. This study underscores the potential of Alum sludge as a viable solution for phosphate management in environmental cleanup efforts.

Determination of water quality and efficient removal of arsenic and iron from groundwater using mahogany fruit husk and banana peduncle charcoals

The groundwater (GW) of Bangladesh is predominantly contaminated with arsenic (As) and iron (Fe) which has a bad impact on human health. We tried to remove these elements with easily available mahogany-fruit (Swietenia mahagoni) husk charcoal (MHC) and banana (Musa acuminata) peduncle charcoal (BPC). The trial was implemented with 3 replications throughout the research. The sampled GW contained 0.06 mg As L−1 and 4.83 mg Fe L−1. Firstly, the pH was 3, 5, 7, and 9 with a 250 mg L−1 dose. The MHC removed almost 91.05 % of As at pH 5.0, and BPC removed almost 86.67 % of As at pH 9. However, in the case of Fe, the MHC removed almost 100 % at pH 7 and 9; and BPC removed the same quantity at pH 5, 7, and 9. Secondly, the contact times were 0, 5, 10, 20, and 40 min with a 250 mg L−1 dose at pH 7.0. The maximum removal of As and Fe was 100 % with MHC and BPC at 5 min. The pseudo-first-order kinetic, pseudo-second-order kinetic, and intra-particle diffusion models were considered. The result showed that the rate of adsorption followed the pseudo-second-order kinetic model. Lastly, the adsorbent doses were 0, 50, 150, 250, and 350 mg L−1. At pH 7, the highest removal of As was 79.47 % and Fe removal was 100 % at 350 mg L−1 dose for MHC. Similarly, the values were 79.29 % and 100 % for the same at 350 mg L−1 dose of BPC, indicating these charcoal are good for heavy metals removal.