International Electrotechnical Commission Research Articles

Hydrokinetic tidal energy resource assessment following international electrotechnical commission guidelines

Energetic tidal streams are an especially attractive source of clean energy due to the daily occurrence of high tidal flows. However, before any deployment of tidal turbine farms, it is essential to perform a resource assessment depending on the scope and scale of the project. The International Electrotechnical Commission has developed a technical specification for assessing the tidal stream resource “IEC TS 62600-201” to aid in this effort: determine a particular site’s feasibility and design the project layout. In this study, we implemented and validated a three-dimensional numerical model and provided results following the specification for a ‘Stage 2’ project layout design in a highly energetic tidal channel: Tacoma Narrows of Puget Sound, in the State of Washington, USA. Implementation of the numerical model based on the specification has helped estimate the annual energy production with higher model accuracy. We also used the same setup to evaluate the undisturbed theoretical and technical resources, where the latter included energy extraction from the flow field arranging a hypothetical tidal energy converter array. Ultimately, this work has shown the important role of the technical specification in larger project layout design, which can simultaneously act as a benchmark for other ‘Stage 2’ theoretical and technical resource assessment studies worldwide.

The occurrence and mechanism of hysteresis between axial deformation and short‐circuit electromagnetic force during the vibration of power transformer windings

AbstractMechanical stability is one of the core capabilities of power transformers. External short‐circuit accidents are the main cause of winding instability. International Electrotechnical Commission 60076‐5 standard recommends a method to calculate the short‐circuit strength of power transformer windings by comparing the stress within windings under the effect of the maximum electromagnetic force with the critical stress of the winding. This method assumes that the maximum deformation will be produced by the maximum electromagnetic force, which corresponds to the first peak of the waveform. However, owing to the interactions between disks during the vibration process, the maximum deformation may occur after the occurrence of the maximum electromagnetic force. The hysteresis phenomenon between disk deformation and electromagnetic force is studied. The definition of the hysteresis phenomenon during the vibration process is first demonstrated, and the mechanism of the hysteresis phenomenon is investigated. The vibration model is established. By decoupling analysis, the conditions for the formation of hysteresis are proposed, and the mechanism of the hysteresis phenomenon is validated by the experiment, which is conducted on a winding sample. In the deformation formula, the term that determines the time‐varying characteristic is found. The waveform‐determining term is the difference between the two cosine components, whose frequencies are the natural vibration frequency and the electromagnetic force frequency. When the two frequencies are close, the maximum deformation lags behind the maximum force, and the hysteresis phenomenon occurs.

Improving Thermal Stability of Perovskite Solar Cells by Suppressing Ion Migration

Ion migration presents a formidable obstacle to the stability and performance of perovskite solar cells (PSCs), hindering their progress toward commercial feasibility. Herein, the degradation mechanism of PSCs caused by iodide ion migration, which leads to abnormal changes in photoluminescence transients at the buried interface of perovskite films, is investigated. In light of this problem, a novel strategy is proposed to mitigate ion migration by introducing poly(2‐vinylnaphthalene) into poly[bis(4‐phenyl)(2,4,6‐trimethylphenyl)amine] as the hole transport layer with improved ion‐blocking capability. Consequently, this layer effectively reduces defect concentration, suppresses ion migration, and modulates energy level alignment, leading to an impressive efficiency exceeding 23% for doctor‐bladed FAPbI3 PSCs. Moreover, the corresponding unencapsulated devices demonstrate remarkable durability, maintaining over 80% of their initial value after undergoing rigorous stress tests in accordance with the International Electrotechnical Commission 61215 standard for temperature, humidity, and illumination. These tests include 1000 h of thermal cycling and a long‐term operational test lasting 600 h under maximum power point tracking.

Tropical cyclone low-level wind speed, shear, and veer: sensitivity to the boundary layer parametrization in the Weather Research and Forecasting model

Abstract. Mesoscale modeling can be used to analyze key parameters for wind turbine load assessment in a large variety of tropical cyclones. However, the modeled wind structure of tropical cyclones is known to be sensitive to the boundary layer scheme. We analyze modeled wind speed, shear, and wind veer across a wind turbine rotor plane in the eyewall and outer cyclone. We further assess the sensitivity of wind speed, shear, and veer to the boundary layer parametrization. Three model realizations of Typhoon Megi are analyzed over the open ocean using three frequently used boundary layer schemes in the Weather Research and Forecasting (WRF) model. All three typhoon simulations reasonably reproduce the cyclone track and structure. The boundary layer parametrization causes up to 15 % differences in median wind speed at hub height between the simulations. The simulated wind speed variability also depends on the boundary layer scheme. The modeled median wind shear is smaller than or equal to 0.11 used in the current IEC (International Electrotechnical Commission) standard regardless of the boundary layer scheme for the eyewall and outer cyclone region. However, up to 43.6 % of the simulated wind profiles in the eyewall region exceed 0.11. While the surface inflow angle is sensitive to the boundary layer scheme, wind veer in the lowest 400 m of the atmospheric boundary layer is less affected by the boundary layer scheme. Simulated median wind veer reaches values up to 1.7×10-2° m−1 (1.2×10-2° m−1) in the eyewall region (outer cyclone region) and is relatively small compared to moderate-wind-speed regimes. On average, simulated wind speed shear and wind veer are highest in the eyewall region. Yet strong spatial organization of wind shear and veer along the rainbands may increase wind turbine loads due to rapid changes in the wind profile at the turbine location.

A Design and Construction of the Vibration Perception Threshold Measurement Device for Diabetes

A Design and Construction of the Vibration Perception Threshold Measurement Device for Diabetes

Enhanced authentication and device integrity protection for GDOI using blockchain

AbstractRecent device‐level cyber‐attacks have targeted IoT critical applications in power distribution systems integrated with the Internet communications infrastructure. These systems utilize group domain of interpretation (GDOI) as designated by International Electrotechnical Commission (IEC) power utility standards IEC 61850 and IEC 62351. However, GDOI cannot protect against novel threats, such as IoT device‐level attacks that can modify device firmware and configuration files to create command and control malicious communication. As a consequence, the attacks can compromise substations with potentially catastrophic consequences. With this in mind, this article proposes a permissioned/private blockchain‐based authentication framework that provides a solution to current security threats such as the IoT device‐level attacks. Our work improves the GDOI protocol applied in critical IoT applications by achieving decentralized and distributed device authentication. The security of our proposal is demonstrated against known attacks as well as through formal mechanisms via the joint use of the AVISPA and SPAN tools. The proposed approach adds negligible authentication latency, thus ensuring appropriate scalability as the number of nodes increases.

Repeatability and reproducibility of physically consistent single sheet testing with H-coil

Measurements of magnetic losses of electric steel are usually performed by International Electrotechnical Commission standardized Epstein testers or Single Sheet Testers (SSTs). According to round robin tests, the corresponding levels of repeatability are of the order of 0.1%, and those of reproducibility are of the order of 1%. However, orders of absolute accuracy are unknown due to the applied “current method.” Here, we report corresponding tests for the so-called “physically consistent SST.” Consistency is achieved by a “giant” tangential field coil on a 50 cm long and 17 cm wide soft magnetic sample, using a thin amorphous yoke for magnetization. Tests were made in two labs with very different working conditions (sea levels of 200 and 1100 m, respectively), with very similarly built-up testers. Measurements were made for peak inductions between 1 and 1.9 T. For two distributed samples, the repeatability errors were lower than 0.3%, and the reproducibility errors were lower than 1%. This indicates that SSTs with an H-coil are not less reliable than current based ones. However, the absolute accuracy can be estimated to be much better, being close to 2%.

Quantitative classification of equipment protection level in concept of zone classification with downtime of protective measures

Handling flammable materials has a risk that can create explosive atmosphere. Such locations are classified as hazardous area, depending on the frequency and volume of explosive atmospheres. General electrical equipment is prohibited in the hazardous area and explosion protected equipment is used. These are the spatial isolation of ignition sources within the fire triangle, but even time isolation can prevent explosion hazards as well. It is proposed a method to classify zones from the calculation of downtime of protective measures based on failure rates and repair times of protective measures related to ventilation in explosive gas atmospheres with the Functional Safety under the time isolation concept. On the other hand, according to International Electrotechnical Commission (IEC) System for Certification to Standards Relating to Equipment for Use in Explosive Atmospheres, explosion protected equipment was also classified as an Equipment Protection Level, "EPL". The EPL should be selected according to the risk of the hazardous area. However, in IEC60079–14:2013, users can choose any EPL according to their risk assessment. In this paper, we clarify the quantitative risk difference of EPLs with expansion the idea of classifying hazardous area from the downtime of protective measures and introduce a means to quantitatively classify the EPL of equipment in an explosive gas atmosphere.

Trends in Measuring Instrument Transformers for Gas-Insulated Switchgears: A Review

Voltage and current measurements in high-voltage substations are fundamental for stable operation. Conventional instrument transformers (ITs) face challenges in gas-insulated switchgears (GISs), such as size, weight, accuracy limitations, and behavioral instability at abnormal voltages and currents. Non-conventional instrument transformers (NCITs) have emerged to address these issues, complying with International Electrotechnical Commission (IEC) standards and providing millivolt-level signals, enabling downsizing of GIS bays. The transition to digital substations, as mandated by IEC 61850-9-2, requires a shift from the conventional 110 V/5 A outputs to levels ranging from millivolts to volts. Electronic instrument transformers (EITs), compliant with the IEC 60044-7 and 8 standards, offer alternatives to conventional ITs with smaller sizes and wider frequency ranges. However, issues remain with EITs, including limited adoption, the necessity of separate power sources, and susceptibility to electromagnetic interference. Recent standards, transitioning to IEC 61869, focus on low-power instrument transformers (LPITs). Low-power voltage transformers (LPVTs) and low-power current transformers (LPCTs), designed with passive components, present potential solutions by directly connecting to merging units (MUs) for digital signal transmission. This review outlines the current status of various IT standards, covering conventional ITs, EITs based on IEC 60044-7 and 8, and LPITs based on IEC 61869-10 and 11. Advancements in sensor technology relevant to these standards are also explored. The paper provides insights into the evolving landscape of instrument transformers, addressing challenges and offering potential pathways for future developments in digital substations.

Secondary neutron dosimetry for conformal FLASH proton therapy.

Cyclotron-based proton therapy systems utilize the highest proton energies to achieve an ultra-high dose rate (UHDR) for FLASH radiotherapy. The deep-penetrating range associated with this high energy can be modulated by inserting a uniform plate of proton-stopping material, known as a range shifter, in the beam path at the nozzle to bring the Bragg peak within the target while ensuring high proton transport efficiency for UHDR. Aluminum has been recently proposed as a range shifter material mainly due to its high compactness and its mechanical properties. A possible drawback lies in the fact that aluminum has a larger cross-sectionof producing secondary neutrons compared to conventional plastic range shifters. Accordingly, an increase in secondary neutron contamination was expected during the delivery of range-modulated FLASH proton therapy, potentially heightening neutron-induced carcinogenic risks to thepatient. We conducted neutron dosimetry using simulations and measurements to evaluate excess dose due to neutron exposure during UHDR proton irradiation with aluminum range shifters compared to plastic rangeshifters. Monte Carlo simulations in TOPAS were performed to investigate the secondary neutron production characteristics with aluminum range shifter during 225MeV single-spot proton irradiation. The computational results were validated against measurements with a pair of ionization chambers in an out-of-field region ( 30cm) and with a Proton Recoil Scintillator-Los Alamos rem meter in a far-out-of-field region (0.5-2.5m). The assessments were repeated with solid water slabs as a surrogate for the conventional range shifter material to evaluate the impact of aluminum on neutron yield. The results were compared with the International Electrotechnical Commission (IEC) standards to evaluate the clinical acceptance of the secondary neutronyield. For a range modulation up to 26cm in water, the maximum simulated and measured values of out-of-field secondary neutron dose equivalent per therapeutic dose with aluminum range shifter were found to be and , respectively, overall higher than the solid water cases (simulation: ; measurement: ). The maximum far out-of-field secondary neutron dose equivalent was found to be ( ) and ( ) for the simulations and rem meter measurements, respectively, also higher than the solid water counterparts (simulation: ( ) ; measurement: ( ) ). We conducted simulations and measurements of secondary neutron production under proton irradiation at FLASH energy with range shifters. We found that the secondary neutron yield increased when using aluminum range shifters compared to conventional materials while remaining well below the non-primary radiation limit constrained by the IECregulations.

Healthcare Providers’ Readiness to Address Medical Device Cybersecurity within the Irish Healthcare System

Medical devices that can diagnose and treat critically ill patients have become sophisticated and complex. Device manufacturers have been developing these systems to meet market requirements as technology evolves. Combining medical devices and ICT into a distributed medical device IT system can be a solution to incorporating continuous monitoring from the patient bedside to interoperability with a clinical information system. These technology innovations aim to manage patient data and configure medical devices into networked systems that can provide functionality and safety. The implementation of a medical device network solution allows a healthcare provider to take advantage of managing the flow of information to improve clinical work practices and implement a system that can be interoperable with other clinical information systems. International Electrotechnical Commission (IEC) 80001-1 was developed to assist healthcare providers in identifying and managing the risks associated with medical devices sharing the same IT network with other systems and software. This standard defines roles, responsibilities, and activities in relation to the management of risk with medical devices on an IT network. This study aims to determine if the standard International Electrotechnical Commission (IEC) 80001-1 is being implemented and determine familiarity with regulations and appropriate standards and guidance for an effective medical device security risk-management program with Irish healthcare providers. A literature review highlighted the restrictions healthcare providers face in adopting and implementing IEC 80001-1 and the security threats and risks present when integrating medical devices and IT networks. The study research was conducted with clinical engineering members of the Biomedical and Clinical Engineering Association of Ireland (BEAI). This survey targeted BEAI members due to their wealth of experience, knowledge, and skill level in supporting complex medical device systems. An online anonymous survey was created to determine knowledge, awareness, and familiarity with IEC 80001-1 and other medical device security risk-management guidelines. The study research results revealed low knowledge, awareness, and familiarity among research participants with IEC 80001-1 and guidelines on medical device security risk management. These results were consistent with the literature review that a key to the success of standard adoption is collaboration between stakeholders and a multidisciplinary approach to compliance.

Cybersecurity of Industrial Systems—A 2023 Report

The article explores the importance of cybersecurity in Industry 4.0, specifically focusing on safeguarding industrial automation systems from cyberattacks. It discusses essential security measures, network monitoring, and employee training, emphasizing the significance of risk management for ensuring industry stability. Adherence to industrial security standards, such as ISA/IEC 62443, is crucial (ISA—International Society of Automation, IEC—International Electrotechnical Commission). The article outlines cyberthreat challenges and their impact on various sectors, including healthcare and finance, as well as the risks faced by large industrial enterprises. Additionally, it elucidates evolving cybersecurity strategies and principles, underscoring the necessity for continuous, multi-layered protection. Collaboration with operators, strict information security policies, and robust incident response plans are emphasized. The importance of risk monitoring and adaptability to ever-changing threat landscapes is highlighted, emphasizing the collaborative and flexible nature of cybersecurity in the face of escalating digital threats.

Robotics, Artificial Intelligence, and Drones in Solar Photovoltaic Energy Applications—Safe Autonomy Perspective

While there is evidence of substantial improvement in efficiency and cost reduction from the integration of Robotics, Artificial Intelligence, and Drones (RAID) in solar installations; it is observed that there is limited oversight by international standards such as the International Electrotechnical Commission (IEC) in terms of the hazards and untapped potentials. This is partly because it is an emerging application and generally burdened with social acceptability issues. Thus, the safety regulations applied are adaptations of device-specific regulations as deemed fit by individual companies. Also, due to the fast-paced technological development of these platforms, there is huge potential for applications that are not currently supported by the device-specific regulations. This creates a multi-faceted demand for the establishment of standardized, industry-wide polices and guidelines on the use of RAID platforms for Solar PV integrations. This work aims to address critical safety concerns by conducting a comprehensive high-level system examination applicable to the monitoring and maintenance of Solar PV systems. Standard safety assurance models and approaches are examined to provide a safe autonomy perspective for Solar PVs. It is considered that, as RAID applications continue to evolve and become more prevalent in the Solar PV industry, standardized protocols or policies would be established to ensure safe and reliable operations.

Modelling of cup anemometry and dynamic overspeeding in average wind speed measurements

Abstract. Cup anemometers measure average wind speed in the atmosphere and have been used for one and a half centuries by meteorologists. Within the last half century, cup anemometers have been used extensively in wind energy to measure wind resources and performance of wind turbines. Meteorologists researched cup anemometer behaviour and found dynamic overspeeding to be an inherent and significant systematic error. The wind energy community has strong accuracy requirements for power performance measurements on wind turbines, and this led in the last 2 decades to new research on cup anemometer characteristics, which was taken to a new level with the development of improved calibration procedures, cup anemometer calculation models and classification methods. Research projects in wind energy demonstrated, by field and wind tunnel measurements, that angular response was a significant contributor to uncertainty and that dynamic overspeeding was a significant but less important contributor. Earlier research was mainly made on cup anemometers with hemispherical cups on long arms, ​​​​​​​and dynamic overspeeding was considered an inherent and high uncertainty error for cup anemometers. Research on conical cups on short arms has now shown that zero or low overspeeding is present on a well-designed cup anemometer, providing a much lower overspeeding uncertainty error. Different cup anemometer calculation models were investigated in order to find derived overspeeding characteristics. The general and often used parabolic torque coefficient model showed that zero overspeeding is present when the speed ratio roots of the torque coefficient curve go through the equilibrium speed ratio and zero. The two-cup drag model is a special case of the parabolic torque coefficient model but with the second root being reciprocal to the equilibrium speed ratio. The drag model always results in a positive maximum overspeeding of the order of 1.1 times the turbulence intensity squared. A linear torque coefficient results in maximum overspeeding levels equal to the turbulence intensity squared. Torque characteristics of a cup anemometer with hemispherical cups fit slightly well to the drag model, but a cup anemometer with conical cups does not fit to the drag model nor the parabolic model; it fits better to a partial linear model and even better to an optimized torque model. The most accurate modelling of cup anemometer characteristics is at present made with the ACCUWIND model (Dahlberg et al., 2006). This model uses tabulated torque coefficient and angular response data measured in a wind tunnel. The ACCUWIND model is found in International Electrotechnical Commission (IEC) wind turbine power performance standards, where it is used in a classification system for estimation of operational uncertainties. For an actual comparison of two cup anemometers, with respectively hemispherical and conical cups, the influence of dynamic overspeeding was found to be relatively low compared to angular response, but for conical cups it was specifically low.

Pathways to IEC Standards for Heliostat Design Qualification and Site Acceptance in Central Receiver CSP Applications

This paper surveys the existing landscape of standards relevant to heliostats, identifies their gaps, and proposes a path forward to a comprehensive set of heliostat guidelines, technical specifications, and standards under the framework of International Electrotechnical Commission (IEC) TC 117. Gaps in existing guidelines and standards are surveyed using a three-tiered taxonomy: component-level, heliostat-level, and field-level. At each level, the gap analysis is followed by a proposal for a coordinated path forward on the development of standards. At the component level, advances in the understanding of wind loading should inform a technical specification for drives and structures. Reflectors require consolidation of measurement guidelines into existing standards documents. Communications & controls require technical standards to inform their selection and secure implementation. At the heliostat level, IEC 62817 (solar trackers) adequately characterizes drive systems, structures, and electronics, but requires adaptation to heliostats’ use patterns, operating modes, and expected life cycles. IEC 62817 does not address heliostat beam quality and pointing accuracy, but the process for determining both is elaborated in the SolarPACES Guideline for Heliostat Performance Testing. This SolarPACES document requires two main modifications: adaptation to IEC language and inclusion of testing after heliostats which have undergone accelerated weathering and mechanical cycling (to understand performance degradation). At the field level, IEC 62862-4-2 addresses the function and control of heliostat fields but does not cover the statistically rigorous testing of heliostat groups, or field performance factors like security and soiling. The addition of documents under IEC-62862-4 is proposed to address this gap.

A hybrid simulator with novel bicone-wire grid antenna.

The simulator is an indispensable device for the study of high-altitude electromagnetic pulse (HEMP) effects. In order to improve the quality of the electric field waveforms of the HEMP simulator, we carried out simulation and experimental studies for the biconical-wire grid antenna. A new bicone-wire grid antenna HEMP simulator was designed by using skeletonized cones instead of solid cones, which can substantially improve the mobility of the simulator. The effects of different aspect ratios and different cone structures of the simulator on the waveform and distribution characteristics of the electric field were analyzed. The accuracy of the simulation results was verified by testing the bicone-wire grid antenna simulator with the new structure. The results obtained are as follows: First, the simulator can provide a HEMP environment compliant with the International Electrotechnical Commission (IEC) standard in an area of 5 × 6 × 2m3. Second, the simulator possesses optimal waveform quality and working space among simulators with different aspect ratios. Finally, the influence of using skeletonized cones instead of solid cones on the simulator's electric field waveforms is negligible, and the mobility of the new simulator is significantly improved compared to the original simulator.

A metaheuristic-based method for photovoltaic temperature computation under tropical conditions

Tropical climates have favorable irradiation levels for the development of photovoltaic systems; however, high temperatures have a negative impact on the efficiency of solar cells. Since direct measurement of cell temperature is not common, mathematical models are needed to make predictions. Numerous models have been documented, highlighting the challenge of applying a universal model to different climatic conditions. The main contribution of this study is the proposal of a metaheuristic algorithm to accurately compute the temperature of solar cells. This method is simple and effective in exploring numerous potential states of the reference parameters (i.e., irradiance and ambient temperature). Data collected over a 23-month period in two photovoltaic installations with an output power of 2.2 MW of multicrystalline silicon technology were used to develop the proposed method and validate it. The proposed model was compared with 19 previously reported models in the literature. Compared to the model recommended by the International Electrotechnical Commission (IEC Standard 61215-1), the mean square error, mean absolute error (MAE) and mean absolute percentage error were reduced by 4.9, 4.8, and 2.4 times, respectively. The accuracy of the proposed method is demonstrated by MAE errors ranging from 0.56 °C to 1.88 °C, obtained by considering three different daily profiles of irradiance and ambient temperature. Therefore, the proposed method is recommended to more accurately calculate the temperature of the photovoltaic cell in tropical areas.

A novel approach for oil-based transformer fault identification in electrical secondary distribution networks

Oil-immersed transformers are mostly installed equipment in electrical power networks. Thus, ensuring the reliability of these equipment is paramount. Fault identification is one of the measures taken to ensure the reliability. Concerning fault identification mechanisms, several methods exist; one of which is the dissolved gas analysis (DGA) tool that has been widely used purposefully for oil-immersed transformers. The tool is used to capture and analyze the gases dissolved in the oil. Studies have proposed various fault identification methods based on this tool such as the Dornenburg, key gas, and International Electrotechnical Commission (IEC) standards methods using DGA data. However, the accuracy of these methods seems to be limited by the context, such as the type and number of parameters used. In this study, the novel hybrid fault identification method based on multilayer neural networks (MLANN) and expert knowledge is proposed to improve the accuracy fault identification process by considering the specific characteristic parameters extracted from the historical DGA dataset. The proposed hybrid method improves accuracy by 14.46% when compared to 12 benchmark methods. This improvement portrays that our method can be integrated into a scheduling platform for maintenance decision support in an electrical power network with accuracy. Furthermore, the promising accuracy in transformer fault identification is expected to increase safety and power reliability.

Analysis of NREL-5MW wind turbine wake under varied incoming turbulence conditions

The offshore environment is an ideal site for wind farm development as it offers abundant wind energy resources. Investigating offshore wind turbine wake under different turbulence conditions is essential for enhancing energy generation efficiency and promoting sustainable development. This paper utilizes a synthetic turbulence method called Discretizing and Synthesizing Random Flow Generation (DSRFG) to generate four categories of turbulence environments based on International Electrotechnical Commission design requirements for offshore wind turbines. A standalone NREL offshore 5-MW baseline wind turbine is then simulated using the actuator line method coupled with large eddy simulation. Proper Orthogonal Decomposition is employed to analyze the wake characteristics under different incoming turbulence conditions. For the overall wake behaviors, the flow mode, in which some tip vortices flow back towards the hub, become more significant with higher incoming turbulence intensity. Those vortices disturb the turbine and result in unfavorable effects. Meanwhile, when the detailed characteristics of the wake are studied, each primary mode experiences an increase in the number of small-scale vortices with higher incoming turbulence intensity. It results from the interaction between the wake and outer flow, which accelerates wake recovery and benefits the downstream turbine.

Data quality processing for photovoltaic system measurements

The operation and maintenance activities in photovoltaic systems use meteorological and electrical measurements that must be reliable to check system performance. The International Electrotechnical Commission (IEC) standards have established general criteria to filter erroneous information; however, there is no standardized process for the evaluation of measurements. In the present work we developed 3 procedures to detect and correct measurements of a photovoltaic system based on the single diode model. The performance evaluation of each criterion was tested with 6 groups of experimental measurements from a 3 kWp installation. Based on the error of the 3 procedures performed, the most unfavorable case has been prioritized. Then, the reduction of errors between the estimated and measured value has been achieved, reducing the number of measurements to be corrected. For the clear sky categories, the coefficient of determination is 0.9975 and 0.9961 for the high irradiance profile. Although an increase of 2.5% for coefficient of determination has been achieved, the overcast sky categories should be analyzed in more detail. Finally, the different causes of measurement error should be analyzed, associated with calibration errors and sensor quality.