Inter-source Interferometry Research Articles

Inter-Source Interferometry of Seismic Body Waves: Required Conditions and Examples

Inter-Source Interferometry of Seismic Body Waves: Required Conditions and Examples

Toward Source Region Tomography With Intersource Interferometry: Shear Wave Velocity From 2018 West Bohemia Swarm Earthquakes

AbstractThe concept of seismic interferometry embraces the construction of waves traveling between receivers or sources with cross‐correlation techniques. In the present study cross correlations of coda waves are used to measure traveltimes of shear waves between earthquake locations for five event clusters of the 2018 West Bohemia earthquake swarm. With the help of a high‐quality earthquake catalog, I was able to determine the shear wave velocity in the region of the five clusters separately. The shear wave velocities range between 3.5 and 4.2 km/s. The resolution of this novel method is given by the extent of the clusters and better than for a comparable classical tomography. It is suggested to use the method in a tomographic inversion and map the shear wave velocity in the source region with unprecedented resolution. Furthermore, the influence of focal mechanisms and the attenuation properties on the polarity and location of the maxima in the cross‐correlation functions is discussed. The intracluster ratio of P wave to S wave velocity is approximately fixed at 1.68.

Near-surface scattered waves enhancement with source-receiver interferometry

Near-surface scattered waves (NSWs) are the main noise in seismic data in areas with a complex near surface and can be divided into surface-to-surface scattered waves and body-to-surface scattered waves. We have developed a method for NSW enhancement that uses modified source-receiver interferometry. The method consists of two parts. First, deconvolutional intersource interferometry is used to cancel the common raypath of seismic waves from a near-surface scatterer to the common receiver and the receiver function. Second, convolutional interreceiver interferometry is used to compensate the common raypath of seismic waves from the common source to the near-surface scatterer and the source function. For an isotropic point scatterer near the earth’s surface in modified source-receiver interferometry, a body-to-surface scattered wave can be reconstructed by constructive interference not only among three body-to-surface scattered waves but also among a body-to-surface scattered wave and two surface-to-surface scattered waves; a surface-to-surface scattered wave can be reconstructed by constructive interference not only among three surface-to-surface scattered waves but also among a surface-to-surface scattered wave and two body-to-surface scattered waves. According to stationary phase analysis based on the superposition principle, we have developed a so-called dual-wheel driving configuration of modified source-receiver interferometry for enhancing NSWs in the data of conventional seismic exploration. The main advantages of the scheme are that (1) it can be used to enhance NSWs without the need for any a priori knowledge of topography and near-surface velocity, (2) it can be used to reconstruct NSWs from real sources to real receivers, including 3D near-surface side-scattered waves, and (3) it can be applied to conventional seismic data with finite-frequency bandwidth, spatially limited and sparse arrays, different source and receiver functions, and static correction. Numerically simulated data and field seismic data are used to demonstrate the feasibility and effectiveness of the scheme.

Retrieving virtual reflection responses at drill-bit positions using seismic interferometry with drill-bit noise

In the field of seismic interferometry, researchers have retrieved surface waves and body waves by cross-correlating recordings of uncorrelated noise sources to extract useful subsurface information. The retrieved wavefields in most applications are between receivers. When the positions of the noise sources are known, inter-source interferometry can be applied to retrieve the wavefields between sources, thus turning sources into virtual receivers. Previous applications of this form of interferometry assume impulsive point sources or transient sources with similar signatures. We investigate the requirements of applying inter-source seismic interferometry using non-transient noise sources with known positions to retrieve reflection responses at those positions and show the results using synthetic drilling noise as source. We show that, if pilot signals (estimates of the drill-bit signals) are not available, it is required that the drill-bit signals are the same and that the phases of the virtual reflections at drill-bit positions can be retrieved by deconvolution interferometry or by cross-coherence interferometry. Further, for this case, classic interferometry by cross-correlation can be used if the source power spectrum can be estimated. If pilot signals are available, virtual reflection responses can be obtained by first using standard seismic-while-drilling processing techniques such as pilot cross-correlation and pilot deconvolution to remove the drill-bit signatures in the data and then applying cross-correlation interferometry. Therefore, provided that pilot signals are reliable, drill-bit data can be redatumed from surface to borehole depths using this inter-source interferometry approach without any velocity information of the medium, and we show that a well-positioned image below the borehole can be obtained using interferometrically redatumed reflection responses with just a simple velocity model. We discuss some of the practical hurdles that restrict the application of the proposed method offshore.

Source-receiver interferometry for seismic wavefield construction and ground-roll removal

Seismic interferometry describes the construction of unmeasured wavefield responses (or Green's functions) between two or more points by applying cross-correlation, deconvolution, or convolution to seismic data recordings. The practical implications are that, applying inter-receiver interferometry, a “virtual” (imaginary) source of energy can be created at the location to a real receiver by using energy recorded from surrounding sources. Similarly, by using inter-source interferometry, a virtual receiver can be created at the location of a real source by using energy recorded at surrounding receivers (Curtis et al., 2009). These two methods can be combined to create the new technique of source-receiver interferometry (Curtis, 2009; Curtis and Halliday, 2010; Halliday and Curtis, 2010) which synthesizes real-source to real-receiver Green's function estimates using only energy recorded at a surrounding boundary of receivers and from an additional surrounding boundary of sources. The boundary sources in each case can be active (such as an explosive or vibrating source) or passive (such as noise from anthropogenic activity or ocean waves). This paper describes the first real-data application of source-receiver interferometry, and demonstrates its potential to enhance existing methods of interferometric ground-roll suppression.