Integrated Microring Resonator Research Articles

Design and simulation of a tunable parity-time symmetric optoelectronic oscillator utilizing integrated components

Non-Hermitian photonics, relaying on parity-time (PT) symmetry, have shown promise in achieving mode selection for optical or microwave single-mode oscillation. Typically, a PT-symmetric system is constructed using two coupled loops with identical geometry. This article utilizes the PT-symmetry property to select a single frequency mode in an optoelectronic oscillator (OEO). However, traditional OEO implementations often involve discrete components, limiting widespread adoption due to factors such as size, weight, power consumption, and cost. Our aim in this paper is to leverage integrated components within the OEO loop. The proposed structure incorporates an integrated micro-ring resonator (MRR) with a high-quality factor (Q-factor) that serves both as a modulator and a resonator. Additionally, we suggest employing an adjustable integrated power splitter utilizing a micro heater to balance the gain and loss of two mutually coupled OEO loops. In this configuration, two integrated photo detectors (PD) are also utilized. In this setup, the single-frequency mode can be easily identified by simultaneously utilizing the properties of PT-symmetry and an integrated high-Q-factor resonator, obviating the need for a narrowband microwave filter. By adjusting the center frequency of the microwave photonic filter (MPF), the frequency of the generated signal can be tuned over a wide range. For instance, setting the generated frequency of the microwave signal to 11.5 GHz results in a measured phase noise of − 76.5 dBc/Hz at a 10-kHz offset frequency, with a side mode suppression ratio (SMSR) of 40 dB.

On-Chip Quantum Information Processing with Distinguishable Photons.

Multiphoton interference is at the heart of photonic quantum technologies. Arrays of integrated cavities can support bright sources of single photons with high purity and small footprint, but the inevitable spectral distinguishability between photons generated from nonidentical cavities is an obstacle to scaling. In principle, this problem can be alleviated by measuring photons with high timing resolution, which erases spectral information through the time-energy uncertainty relation. Here, we experimentally demonstrate that detection can be implemented with a temporal resolution sufficient to interfere photons detuned on the scales necessary for cavity-based integrated photon sources. By increasing the effective timing resolution of the system from 200 to 20ps, we observe a 20% increase in the visibility of quantum interference between independent photons from integrated microring resonator sources that are detuned by 6.8GHz. We go on to show how time-resolved detection of nonideal photons can be used to improve the fidelity of an entangling operation and to mitigate the reduction of computational complexity in boson sampling experiments. These results pave the way for photonic quantum information processing with many photon sources without the need for active alignment.

Integrated photon pair source based on a silicon nitride micro-ring resonator for quantum memories.

We report the design of an integrated photon pair source based on spontaneous four-wave mixing (SFWM), implemented in an integrated micro-ring resonator in the silicon nitride platform (Si3N4). The signal photon is generated with emission at 606 nm and bandwidth of 3.98 MHz, matching the spectral properties of praseodymium ions (Pr), while the idler photon is generated at 1430.5 nm matching the wavelength of a CWDM channel in the E-band. This novel, to the best of our knowledge, device is designed to interact with a quantum memory based on a Y2SiO5 crystal doped with Pr3+ ions, in which we used cavity-enhanced SFWM along with dispersion engineering to reach the required wavelength and the few megahertz signal photon spectral bandwidth.

Mode-locked laser with multiple timescales in a microresonator-based nested cavity

Mode-locking techniques have played a pivotal role in developing and advancing laser technology. Stable fiber-cavity configurations can generate trains of pulses spanning from MHz to GHz speeds, which are fundamental to various applications in micromachining, spectroscopy, and communications. However, the generation and exploitation of multiple timescales in a single laser cavity configuration remain unexplored. Our work demonstrates a fiber-cavity laser configuration designed to generate and control pulse trains from nanosecond to picosecond timescales with a broadband output and a low mode-locking threshold. Our approach exploits a frequency mode-locking mechanism that simultaneously drives the modes of an integrated microring resonator nested within an external fiber-loop cavity, guaranteeing ultra-stable operation. By selectively filtering the nested cavity modes, we can transition from nanosecond pulses to pulse burst trains in which nanosecond and picosecond components coexist. Our laser configuration produces a train of pulses with durations of 5.1 ns and 3.1 ps at repetition rates of 4.4 MHz and 48.7 GHz, with time-bandwidth products close to the transform-limited values of 0.5 and 0.46, respectively. Moreover, in the absence of frequency modulation, we demonstrate the generation of comb spectra with an adjustable central wavelength. Our findings have the potential to significantly contribute to the development of cutting-edge technologies and applications, harnessing the distinct advantages of mode-locked pulses across various scientific and engineering disciplines.

Optical Feedback FM-to-AM Conversion with integrated Micro-Ring Resonator for Displacement Sensing Applications

In this study, we show the capability of integrated Micro-Ring Resonators (MRRs) to perform frequency-to-amplitude (FM-to-AM) conversion of optical feedback interferometry (OFI) signals with improved signal-to-noise ratio compared to conventional AM OFI signals. Further, contrary to traditional OFI FM-to-AM conversion techniques using gas cell-based edge filters and free-space or fiber Mach-Zehnder Interferometers (MZI), integrated photonic processing offers greater compactness and perturbation resilience, enhancing noise performance through improved temperature control and immunity to parasitic mechanical vibrations. The OFI FM-to-AM conversion was performed with a fabricated silicon nitride MRR of radius 120 μm and a quality factor of 130,000. The FM-to-AM conversion factor achieved was 0.61 GHz−1, with a noise equivalent displacement of only 4.9 nm for a 1 kHz bandwidth. This demonstration highlights the potential of integrated edge filters to replace traditional freespace and fiber architectures, more prone to environmental perturbations, in OFI signal processing for vibrometric applications.

Dynamic Spectrum Assignment in Passive Optical Networks Based on Optical Integrated Microring Resonators Using Machine Learning and a Routing, Modulation Level, and Spectrum Assignment Method

The rising demand for bandwidth in optical communication networks has led to the need for more efficient solutions for spectrum allocation. This article presents a solution to enhance the capacity and efficiency of passive optical networks (PON) using optical microring resonators and dynamic spectrum allocation. The solution relies on wavelength division multiplexing (WDM). It proposes using a support vector machine (SVM) and a Routing, Modulation Level, and Spectrum Assignment (RMLSA) method to manage spectrum allocation based on the bandwidth and distance of multiple requests. The network employs a pulse shaper to physically allocate the spectrum, allowing for the separation of the spectrum generated by the microring resonators into different wavelengths or wavelength ranges (super-channel). Additionally, the SVM and RMLSA algorithms regulate the pulse shaper to execute the allocation. This photonic network achieves improved spectrum utilization and reduces the network blocking probability. Our proposal shows that we successfully addressed 1090 requests with a zero blocking probability, accounting for 81% of the total requests. These request scenarios can simultaneously accommodate up to 200 requests, with a maximum bandwidth of 31 THz. This highlights the efficacy of our approach in efficiently managing requests with substantial processing capacity.

Thermo-Optic Response and Optical Bistablility of Integrated High-Index Doped Silica Ring Resonators.

The engineering of thermo-optic effects has found broad applications in integrated photonic devices, facilitating efficient light manipulation to achieve various functionalities. Here, we perform both an experimental characterization and a theoretical analysis of these effects in integrated microring resonators made from high-index doped silica, which have had many applications in integrated photonics and nonlinear optics. By fitting the experimental results with theory, we obtain fundamental parameters that characterize their thermo-optic performance, including the thermo-optic coefficient, the efficiency of the optically induced thermo-optic process, and the thermal conductivity. The characteristics of these parameters are compared to those of other materials commonly used for integrated photonic platforms, such as silicon, silicon nitride, and silica. These results offer a comprehensive insight into the thermo-optic properties of doped silica-based devices. Understanding these properties is essential for efficiently controlling and engineering them in many practical applications.

Microresonator Effective Thermal Parameters Definition via Thermal Modes Decomposition

High-Q optical microresonators are particularly efficient practical tools of modern applied optics and photonics. Using them, one inevitably faces the problem of thermal effects. Accurate determination of effective thermal parameters of high-Q microresonators (effective thermal relaxation rate and optical absorption rate) is of particular importance for developing microresonator-based devices. Our investigation looks into diverse methodologies to estimate these effective parameters for such systems, ultimately revealing a divergence between the commonly employed simplified model, the direct numerical approach, and classical analytical formulas. We introduce a novel approach to calculate effective parameters based on the decomposition of the thermal field into microresonator thermal modes, which inherently considers the intricate geometry and material anisotropy inherent in microresonators, as well as the influence of external conditions. The method for the accurate determination of the effective thermal parameters of the microresonator for corresponding thermal modes is developed. As a result of applying this method, we modified the classical approach for the simulation of thermal effects in optical microresonators for better agreement with the numerical simulations. By accounting for the complexities of microresonator shapes, material properties, and external factors, our proposed method contributes to a more accurate understanding of thermal dynamics and enhances the predictive capabilities of simulations for these systems. We demonstrated the application of this method on the example of integrated microring resonators, but it can be used to analyze thermal effects in other microresonator platforms.

Sidewall grating slot waveguide microring resonator biochemical sensor.

Integrated microring resonator structures based on silicon-on-insulator (SOI) platforms are promising candidates for high-performance on-chip sensing. In this work, a novel sidewall grating slot microring resonator (SG-SMRR) with a compact size (5 µm center radius) based on the SOI platform is proposed and demonstrated experimentally. The experiment results show that the refractive index (RI) sensitivity and the limit of detection value are 620 nm/RIU and 1.4 × 10-4 RIU, respectively. The concentration sensitivity and minimum concentration detection limit are 1120 pm/% and 0.05%, respectively. Moreover, the sidewall grating structure makes this sensor free of free spectral range (FSR) limitation. The detection range is significantly enlarged to 84.5 nm in lab measurement, four times that of the FSR of conventional SMRRs. The measured Q-factor is 3.1 × 103, and the straight slot waveguide transmission loss is 24.2 dB/cm under sensing conditions. These results combined with the small form factor associated with a silicon photonics sensor open up applications where high sensitivity and large measurement range are essential.

Influence of Losses, Device Size, and Mode Confinement on Integrated Micro-Ring Resonator Performance for Absorption Spectroscopy Using Evanescent Field Sensing

This work presents a detailed modeling-based analysis of integrated micro-ring resonators used for absorption spectroscopy. Generally, sensors based on micro-ring resonators detect changes in the real part of the sensing medium refractive index, at critical coupling. In absorption spectroscopy, however, micro-ring resonators are used to measure changes in the imaginary part of the index and are most sensitive away from critical coupling, with separate maxima in the under- and over-coupled regimes. In this work, we present a detailed analysis of the under-coupled regime, explaining the relationships between sensitivity, mode confinement, and losses. The analysis is based on reverse-symmetry waveguides to increase the proportion of mode power in the sensing medium and incorporates a realistic model of propagation losses based on experimental measurements of sidewall roughness. The analysis demonstrates that the resonant nature of the sensor is most effective at small radii compared to a non-resonant structure of equal size and shows a behavior of diminishing returns at larger device sizes regarding sensitivity and elevated proportions of mode power in the evanescent field.

Power-fading-mitigation approach in an intensity-modulated radio-over-fiber link using a single integrated micro-ring resonator

In this paper we address the limiting effect of power fading (PF) in fiber optic communication links, due to the fiber’s dispersive properties, and suggest a mitigation approach in intensity-modulated radio-over-fiber (RoF) applications. The proposed method is independent of the length of the optical transmission path. PF is mitigated by employing a simple integrated photonic structure, i.e., a single micro-ring resonator. The latter features a periodic notch-filter response, employed to suppress one of the sidebands in an optical double sideband (ODSB) modulation, reducing the PF of the received RF signal. The suppression ratio measured by the optical spectrum analyzer is 24 dB. In this way we succeeded in reducing the RF signal’s power ripple at the receiving end to 3 dB. The proposed approach promises an economic yet effective solution to overcoming the PF in point-to-multipoint-topology optical networks.

Microwave frequency measurement using a silicon integrated microring resonator.

Photonics-assisted instantaneous frequency measurement of a microwave signal using a silicon integrated microring resonator (MRR) is proposed and experimentally demonstrated. The frequency of a microwave signal has a unique relationship with the power ratio between the two microwave signals at the outputs of two microwave photonic filters (MPF) with complementary frequency responses. The key device to implement the MPFs is a silicon integrated MMR, which is employed to convert a phase-modulated optical signal to an intensity-modulated optical signal by placing two optical carriers at the complementary slopes of the MRR. For a given frequency measurement range and resolution, an MRR is designed and fabricated, and its use for instantaneous microwave frequency (IMF) measurement is implemented. For the fabricated MRR, an IMF measurement range of 14-25 GHz with a measurement accuracy of ±0.2GHz is achieved.

Degenerate squeezing in a dual-pumped integrated microresonator: Parasitic processes and their suppression

Using a general Hamiltonian treatment, we theoretically study the generation of degenerate quadrature squeezing in a dual-pumped integrated microring resonator coupled to a waveguide. Considering a dual-pump four-wave mixing configuration in an integrated $\text{Si}_3\text{N}_4$ platform, and following the coupled-mode theory approach, we investigate the effects of parasitic quantum nonlinear optical processes on the generation of squeezed light. Considering five resonance modes in this approach allows us to include the most important four-wave mixing processes involved in such a configuration. We theoretically explore the effects of the pump detunings on different nonlinear processes and show that the effects of some of the parasitic processes are effectively neutralized by symmetrically detuning the two pumps. This yields a significant enhancement in the output squeezing quality without physically changing the structure, but suffers from the trade-off of requiring substantially higher pump power for a fixed target level of squeezing.

Conversion Efficiency in Kerr-Microresonator Optical Parametric Oscillators: From Three Modes to Many Modes.

Optical parametric oscillation in a Kerr nonlinear microresonator can generate coherent laser light with frequencies that are widely separated from the pump frequency, allowing, for example, visible light to be generated using a near-infrared pump. To be practically useful, the pump-to-signal conversion efficiency must be far higher than what has been demonstrated in microresonator-based oscillators with widely-separated output frequencies. To address this challenge, here we theoretically and numerically study parametric oscillations in Kerr nonlinear microresonators, revealing an intricate solution space that arises from an interplay of nonlinear processes. As a start, we use a three-mode approximation to derive an efficiency-maximizing relation between pump power and frequency mismatch. However, realistic devices, such as integrated microring resonators, support far more than three modes. Hence, a more accurate model that includes the entire modal landscape is necessary to determine potential inefficiencies arising from unwanted competing nonlinear processes. To this end, we numerically simulate the Lugiato-Lefever Equation that accounts for the full spectrum of nonlinearly-coupled resonator modes. We observe and characterize two nonlinear phenomena linked to parametric oscillations in multi-mode resonators: Mode competition and cross phase modulation-induced modulation instability. Both processes may impact conversion efficiency. Finally, we show how to increase the conversion efficiency to ≈ 25 % by tuning the microresonator loss rates. Our analysis will guide microresonator designs that aim for high conversion efficiency and output power.

MoS2 hybrid integrated micro-ring resonator phase shifter based on a silicon nitride platform

We demonstrate a low-power, compact micro-ring phase shifter based on hybrid integration with atomically thin two-dimensional layered materials, and experimentally establish a low-loss silicon nitride platform. Using a wet transfer method, a large-area few-layer MoS2 film is hybrid integrated with a micro-ring phase shifter, leading to a tuning efficiency of 5.8 pm V-1 at a center wavelength of 1545.294 nm and a half-wave-voltage-length product as low as 0.09 V cm. Our device is designed to provide a hybrid-integration-based active phase modulation scheme for integrated optical communication networks with large-cross-section silicon nitride waveguides.

Blind source separation with integrated photonics and reduced dimensional statistics.

Microwave communications have witnessed an incipient proliferation of multi-antenna and opportunistic technologies in the wake of an ever-growing demand for spectrum resources, while facing increasingly difficult network management over widespread channel interference and heterogeneous wireless broadcasting. Radio frequency (RF) blind source separation (BSS) is a powerful technique for demixing mixtures of unknown signals with minimal assumptions, but relies on frequency dependent RF electronics and prior knowledge of the target frequency band. We propose photonic BSS with unparalleled frequency agility supported by the tremendous bandwidths of photonic channels and devices. Specifically, our approach adopts an RF photonic front-end to process RF signals at various frequency bands within the same array of integrated microring resonators, and implements a novel two-step photonic BSS pipeline to reconstruct source identities from the reduced dimensional statistics of front-end output. We verify the feasibility and robustness of our approach by performing the first proof-of-concept photonic BSS experiments on mixed-over-the-air RF signals across multiple frequency bands. The proposed technique lays the groundwork for further research in interference cancellation, radio communications, and photonic information processing.

Current sensor based on an integrated micro-ring resonator and superparamagnetic nanoparticles.

An ultra-small integrated photonic current sensor based on a silicon micro-ring resonator (MRR) with a cladding layer of Fe3O4 superparamagnetic nanoparticles (SPNPs) is demonstrated. In the magnetic field generated by an alternating current, the Fe3O4 SPNPs lose energy and change the MRR temperature, which leads to a spectral shift in the MRR transmission. The sensor was demonstrated with good linearity in the frequency range 0-60 kHz and current amplitudes from 0 to 0.5 A. This work provides a basis for integrated micro-current sensors, and promotes the development of photoelectric sensors on silicon substrates.

Broadband Microwave Frequency Conversion Based on an Integrated Optical Micro-Comb Source

We report a broadband microwave frequency converter based on a coherent Kerr optical micro-comb generated by an integrated micro-ring resonator. The coherent micro-comb displays features that are consistent with soliton crystal dynamics with an FSR of 48.9GHz. We use this to demonstrate a high-performance millimeter-wave local oscillator at 48.9GHz in the Q-band for microwave frequency conversion. We experimentally verify the microwave performance up to 40 GHz, achieving a ratio of 6.8 dB between output RF power and IF power and a spurious suppression ratio of > 43.5 dB. The experimental results show good agreement with theory and verify the effectiveness of microwave frequency converters based on coherent optical micro-combs, with the ability to achieve reduced size, complexity, and potential cost.

Enhanced NRZ multi-carriers modulation technologies for microresonators in THz technology applications

Abstract Multi-optical carriers suitable for use in an optical communication system have been generated via integrated microring resonators. These carriers were sufficiently stable for travel in either a free space channel or waveguides while experiencing very low dispersion. Multiple carriers were created using the integrated microring resonators, with each carrier possessing a frequency at 193.012, 193.086, 193.186 and 193.268 terahertz (THz). The second part which is the non-return-to-zero (NRZ) modulation has been performed using the microring resonator modulators. The objective of the research is to generate multi-carriers at infrared region and modulate them for the optical communication application using the microring resonators. At the transmitter part, series of microring resonators have been used to generate four different THz frequencies which can be either de-multiplexed and modulated individually using the NRZ modulation format or modulated without de-multiplexing them as these enter a series of microring resonator modulators and microring resonator drop filters. As results, the detection of the four NRZ modulated frequencies has been performed successfully with high signal qualities. Therefore, in this research microring resonators are used for different purposes as to generate optical signals (at the transmitter part), modulate and filter them along an optical transmission link.

Orthogonally Polarized RF Optical Single Sideband Generation and Dual-Channel Equalization Based on an Integrated Microring Resonator

We demonstrate narrowband orthogonally polarized optical radio frequency (RF) single sideband generation as well as dual-channel equalization based on an integrated dual-polarization-mode high- Q microring resonator. The device operates in the optical communications band and enables narrowband RF operation at either 16.6 or 32.2 GHz, determined by the free spectral range and TE/TM mode interval in the resonator. We achieve a very large dynamic tuning range of over 55 dB for both the optical carrier-to-sideband ratio and the dual-channel RF equalization.