Intact Cervical Spine Research Articles

Biomechanical analysis of single and multi-level artificial disc replacement (ADR) in cervical spine using multi-scale loadings: A finite element study.

Artificial disc replacement (ADR) is a clinical procedure used to diagnose cervical degenerative disc disease, preserving range of motion (ROM) at the fixation level and preventing adjacent segment degeneration (ASD). This study analyzed the biomechanics of ADR by examining range of motion (ROM), stress levels in bone and implants, and strain in the bone-implant interface using multi-scale loadings. The study focused on single- and double-level patients across various loading scales during physiological motions within the cervical spine. Results showed increased ROM in single-level and double-level fixations during physiological loadings, while ROM decreased at the adjacent level of fixation with the intact cervical spine model. The Prodisc-Implant metal endplate experienced a maximum von Mises stress of 432 MPa during axial rotation, confirming the long durability and biomechanical performance of the bone-implant interface.

Biomechanical effects of endplate sagittal coverage change on cervical disc replacement: a finite element analysis.

In recent years, the number of artificial cervical disc replacements has increased, and paravertebral ectopic ossification is a common complication. Although the exact mechanism is not clear, some studies suggest that it is related to the concentration of tissue stress caused by incomplete coverage of the trailing edge of the endplate. Therefore, this study performed a quantitative analysis to compare the biomechanical effects of different sagittal distances at the posterior edge of the endplate of the upper and lower prosthesis on the cervical spine and to explore the mechanical response of incomplete coverage of the posterior edge of the endplate on the paravertebral tissues. A C2-C7 nonlinear finite element model of the cervical spine was established and validated. Based on the cervical spine model, cervical disc replacement surgery models were constructed with different distances of sagittal distance at the posterior edge of the upper prosthetic endplate (0, 1, 2, 3mm, respectively) and sagittal distance at the posterior edge of the lower prosthetic endplate (1, 2, 3mm, respectively). Each model was subjected to the same 1Nm torque and 73.6N driven compressive load. Range of motion (ROM), intervertebral disc pressure (IDP), facet joint force (FJF), and endplate stress were measured at the cervical surgical and other segments. Compared to the intact cervical spine model, the sagittal distance of the posterior edge of the prosthesis endplate at different distances increased the stress on the intervertebral disc and the capsular joint in the adjacent vertebral body segments to different degrees, especially in extension. In different directions of motion, the posterior margin sagittal distance of the posterior edge of the endplate of the lower prosthesis has a greater mechanical influence on the cervical spine compared to the posterior margin sagittal distance of the posterior edge of the endplate of the upper prosthesis. Compared with the intact model, the biomechanical parameters (ROM, FJF, endplate stress) of the C5-C6 segment increased the most when the sagittal distance of the posterior edge of the endplate of the upper prosthesis was 3mm. Compared with the intact model, the maximum intervertebral disc stress of C4-C5 and C6-C7 was 0.57MPa and 0.53MPa, respectively, when the sagittal distance of the posterior edge of the upper prosthetic endplate was 3mm. After the sagittal distance of the posterior edge of the prosthetic endplate was completely covered, the mechanical influence of the entire cervical spine was low. The sagittal distance at the posterior edge of the endplate of different sizes changed the motion pattern and load distribution of the implanted segment to some extent. When the sagittal distance between the prosthesis and the upper endplate was greater than or equal to 3mm, the mechanical indices of the implanted segment increased significantly, increasing the risk of local tissue injury, especially during extension motion. Compared to the sagittal distance at the posterior edge of the endplate of the lower prosthesis, increasing the sagittal distance at the posterior edge of the endplate of the upper prosthesis has a greater effect on the mechanics of the cervical spine.

The move-C cervical artificial disc can restore intact range of motion and 3-D kinematics

BACKGROUND CONTEXTIn contrast to cervical discectomy and fusion, total disc replacement (TDR) aims at preserving the motion at the treated vertebral level. Spinal motion is commonly evaluated with the range of motion (ROM). However, more qualitative information about cervical kinematics before and after TDR is still lacking. PURPOSEThe aim of this in vitro study was to investigate the influence of cervical TDR on ROM, instantaneous centers of rotation (ICR) and three-dimensional helical axes. STUDY DESIGNAn in vitro study with human spine specimens under pure moment loading was conducted to evaluate the kinematics of the intact cervical spine and compare it to cervical TDR. METHODSSix fresh frozen human cervical specimens (C4–5, median age 28 years, range 19–47 years, two female and four male) were biomechanically characterized in the intact state and after implantation of a cervical disc prosthesis (MOVE-C, NGMedical, Germany). To mimic in vivo conditions regarding temperature and humidity, water steam was used to create a warm and humid test environment with 37°C. Each specimen was quasistatically loaded with pure moments up to ±2.5 Nm in flexion/extension (FE), lateral bending (LB) and axial rotation (AR) in a universal spine tester for 3.5 cycles at 1 °/s. For each third cycle of motion the ROM was evaluated and an established method was used to determine the helical axis and COR and to project them into three planar X-rays. Statistical analysis was conducted using a Friedman-test and post hoc correction with Dunn-Bonferroni-tests (p<.05). RESULTSAfter TDR, total ROM was increased in FE from 19.1° to 20.1°, decreased in LB from 14.6° to 12.6° and decreased in AR from 17.7° to 15.5°. No statistical differences between the primary ROM in the intact condition and ROM after TDR were detected. Coupled rotation between LB and AR were also maintained. The position and orientation of the helical axes after cervical TDR was in good agreement with the results of the intact specimens in all three motion directions. The ICR in FE and AR before and after TDR closely matched, while in LB the ICR after TDR were more caudal. The intact in vitro kinematics we found also resembled in vivo results of healthy individuals. CONCLUSIONThe results of this in vitro study highlight the potential of artificial cervical disc implants to replicate the quantity as well as the quality of motion of the intact cervical spine. CLINICAL SIGNIFICANCEPhysiological motion preservation was a driving factor in the development of cervical TDR. Our results demonstrate the potential of cervical TDR to replicate in vivo kinematics in all three motion directions.

Biomechanical effect of endplate defects on the intermediate vertebral bone in consecutive two-level anterior cervical discectomy and fusion: a finite element analysis

BackgroundIntermediate vertebral collapse is a newly discovered complication of consecutive two-level anterior cervical discectomy and fusion (ACDF). There have been no analytical studies related to the effects of endplate defects on the biomechanics of the intermediate vertebral bone after ACDF. This study aimed to compare the effects of endplate defects on the intermediate vertebral bone biomechanics in the zero-profile (ZP) and cage-and-plate (CP) methods of consecutive 2-level ACDF and to determine whether collapse of the intermediate vertebra is more likely to occur using ZP.MethodsA three-dimensional finite element (FE) model of the intact cervical spine (C2–T1) was constructed and validated. The intact FE model was then modified to build ACDF models and imitate the situation of endplate injury, establishing two groups of models (ZP, IM-ZP and CP, IM-ZP). We simulated cervical motion, such as flexion, extension, lateral bending and axial rotation, and compared the range of motion (ROM), upper and lower endplate stress, fusion fixation device stress, C5 vertebral body stress, intervertebral disc internal pressure (intradiscal pressure, or IDP) and the ROM of adjacent segments in the models.ResultsThere was no significant difference between the IM-CP model and the CP model in the ROM of the surgical segment, upper and lower endplate stress, fusion fixation device stress, C5 vertebral body stress, IDP, or ROM of the adjacent segments. Compared with the CP model, the endplate stress of the ZP model is significantly higher in the flexion, extension, lateral bending and axial rotation conditions. Compared with the ZP model, endplate stress, screw stress, C5 vertebral stress and IDP in IM-ZP were significantly increased under flexion, extension, lateral bending and axial rotation conditions.ConclusionsCompared to consecutive 2-level ACDF using CP, collapse of the intermediate vertebra is more likely to occur using ZP due to its mechanical characteristics. Intraoperative endplate defects of the anterior lower margin of the middle vertebra are a risk factor leading to collapse of the middle vertebra after consecutive 2-level ACDF using ZP.

Stress Distribution on Spinal Cord According to Type of Laminectomy for Large Focal Cervical Ossification of Posterior Longitudinal Ligament Based on Finite Element Method.

Most studies on the ossification of the posterior longitudinal ligament (OPLL) using the finite element method were conducted in the neutral state, and the resulting decompression was judged to be good. As these studies do not reflect the actual behavior of the cervical spine, this study conducted an analysis in the neutral state and a biomechanical analysis during flexion and extension behaviors. After validation via the construction of an intact cervical spine model, the focal OPLL model was inserted into the C4–C5 segment and a simulation was performed. The neutral state was shown by applying a fixed condition to the lower part of the T1 and Y-axis fixed condition of the spinal cord and simulating spinal cord compression with OPLL. For flexion and extension simulation, a ±30-degree displacement was additionally applied to the top of the C2 dens. Accordingly, it was confirmed that spinal cord decompression did not work well during the flexion and extension behaviors, but rather increased. Thus, if patients with focal OPLL inevitably need to undergo posterior decompression, additional surgery using an anterior approach should be considered.

Intubation biomechanics: Computational modeling to identify methods to minimize cervical spine motion and spinal cord strain during laryngoscopy and tracheal intubation in an intact cervical spine

Study objectiveTo minimize the risk of cervical spinal cord injury in patients who have cervical spine pathology, minimizing cervical spine motion during laryngoscopy and tracheal intubation is commonly recommended. However, clinicians may better aim to reduce cervical spinal cord strain during airway management of their patients. The aim of this study was to predict laryngoscope force characteristics (location, magnitude, and direction) that would minimize cervical spine motions and cord strains. DesignWe utilized a computational model of the adult human cervical spine and spinal cord to predict intervertebral motions (rotation [flexion/extension] and translation [subluxation]) and cord strains (stretch and compression) during laryngoscopy. InterventionsRoutine direct (Macintosh) laryngoscopy conditions were defined by a specific force application location (mid-C3 vertebral body), magnitude (48.8 N), and direction (70 degrees). Sixty laryngoscope force conditions were simulated using 4 force locations (cephalad and caudad of routine), 5 magnitudes (25–200% of routine), and 3 directions (50, 70, 90 degrees). Main resultsUnder all conditions, extension at Oc-C1 and C1-C2 were greater than in all other cervical segments. Decreasing force magnitude to values reported for indirect laryngoscopes (8–17 N) decreased cervical extension to ~50% of routine values. The cervical cord was most likely to experience potentially injurious compressive strain at C3, but force magnitudes ≤50% of routine (≤24.4 N) decreased strain in C3 and all other cord regions to non-injurious values. Changing laryngoscope force locations and directions had minor effects on motion and strain. ConclusionsThe model predicts clinicians can most effectively minimize cervical spine motion and cord strain during laryngoscopy by decreasing laryngoscope force magnitude. Very low force magnitudes (<5 N, ~10% of routine) are necessary to decrease overall cervical extension to <50% of routine values. Force magnitudes ≤24.4 N (≤50% of routine) are predicted to help prevent potentially injurious compressive cord strain.

Intubation Biomechanics: Clinical Implications of Computational Modeling of Intervertebral Motion and Spinal Cord Strain during Tracheal Intubation in an Intact Cervical Spine.

In a closed claims study, most patients experiencing cervical spinal cord injury had stable cervical spines. This raises two questions. First, in the presence of an intact (stable) cervical spine, are there tracheal intubation conditions in which cervical intervertebral motions exceed physiologically normal maximum values? Second, with an intact spine, are there tracheal intubation conditions in which potentially injurious cervical cord strains can occur? This study utilized a computational model of the cervical spine and cord to predict intervertebral motions (rotation, translation) and cord strains (stretch, compression). Routine (Macintosh) intubation force conditions were defined by a specific application location (mid-C3 vertebral body), magnitude (48.8 N), and direction (70 degrees). A total of 48 intubation conditions were modeled: all combinations of 4 force locations (cephalad and caudad of routine), 4 magnitudes (50 to 200% of routine), and 3 directions (50, 70, and 90 degrees). Modeled maximum intervertebral motions were compared to motions reported in previous clinical studies of the range of voluntary cervical motion. Modeled peak cord strains were compared to potential strain injury thresholds. Modeled maximum intervertebral motions occurred with maximum force magnitude (97.6 N) and did not differ from physiologically normal maximum motion values. Peak tensile cord strains (stretch) did not exceed the potential injury threshold (0.14) in any of the 48 force conditions. Peak compressive strains exceeded the potential injury threshold (-0.20) in 3 of 48 conditions, all with maximum force magnitude applied in a nonroutine location. With an intact cervical spine, even with application of twice the routine value of force magnitude, intervertebral motions during intubation did not exceed physiologically normal maximum values. However, under nonroutine high-force conditions, compressive strains exceeded potentially injurious values. In patients whose cords have less than normal tolerance to acute strain, compressive strains occurring with routine intubation forces may reach potentially injurious values.

CT Osteoabsorptiometry Assessment of Subchondral Bone Density Predicts Intervertebral Implant Subsidence in a Human ACDF Cadaver Model.

Cadaveric biomechanics study. Subchondral bone mineral density (sBMD) reflects the long-term mineralization and distribution of stress on joints. The use of 3-dimensional (3-D) methods to evaluate sBMD, including computed tomography osteoabsorptiometry (CT-OAM), enables the assessment of density distribution with emphasis on subchondral bone. This study sought to measure the sBMD of cervical endplates using CT-OAM and correlate it to mechanical implant subsidence in a cadaveric model. Fourteen fresh human cadaveric cervical spines were subjected to dynamic testing after single level discectomy and instrumentation using a PEEK interbody spacer. Specimens were imaged with CT 3 times: 1st) whole intact cervical spine, 2nd) after implantation, and 3 rd) after testing. These images were used to assess sBMD distributions using CT-OAM directly underneath the spacer. Subsidence was defined as the displacement of the device into the endplates. The observed "failure mode" was consistently recorded as subsidence, with a mean of 0.45 ± 0.36 mm and 0.40 ± 0.18 mm for the C4-5 and C6-7 levels, respectively. There were no differences by level. The experimental cyclic test showed that denser endplates experienced less deformation under the same load. This study achieved its stated aim of validating the use of CT-OAM as a method to analyze the sBMD of the cervical endplates. Studies such as this are providing new information on available technology such as CT-OAM, providing new tools for clinicians treating spinal conditions in need of augmentation and stabilization via interbody devices.

A biomechanical analysis of four anterior cervical techniques to treating multilevel cervical spondylotic myelopathy: a finite element study

BackgroundThe decision to treat multilevel cervical spondylotic myelopathy (MCSM) remains controversial. The purpose of this study is to compare the biomechanical characteristics of the intervertebral discs at the adjacent segments and internal fixation, and to provide scientific experimental evidence for surgical treatment of MCSM.MethodsAn intact C2-C7 cervical spine model was developed and validated. Four additional models were developed from the fusion model, including multilevel anterior cervical discectomy and fusion (mACDF), anterior cervical corpectomy and fusion (ACCF), hybrid decompression and fusion (HDF), and mACDF with cage alone (mACDF-CA). Biomechanical characteristics on the plate and the disc of adjacent levels (C2/3, C6/7) were comparatively analyzed.ResultsOf the four models, stress on the upper (C2/3) adjacent intervertebral disc was the lowest in the mACDF-CA group and highest in the ACCF group. Stress on the intervertebral discs at adjacent segments was higher for the upper C2/3 than the lower C6/7 intervertebral disc. In all models, the mACDF-CA group had the lowest stress on the intervertebral disc, while the ACCF group had the highest stress. In the three surgical models with titanium plate fixation (mACDF, ACCF, and HDF), the ACCF group had the highest stress at the titanium plate-screw interface, while the mACDF group had the lowest stress.ConclusionAmong the four anterior cervical reconstructive techniques for MCSM, mACDF-CA makes little effect on the adjacent disc stress, which might reduce the incidence of adjacent segment degeneration (ASD) after fusion. However, the accompanying risk of the increased incidence of cage subsidence should never be neglected.

Biomechanical Study of Cervical Disc Arthroplasty Devices Using Finite Element Modeling.

Many artificial discs for have been introduced to overcome the disadvantages of conventional anterior discectomy and fusion. The purpose of this study was to evaluate the performance of different U.S. Food and Drug Administration (FDA)-approved cervical disc arthroplasty (CDA) on the range of motion (ROM), intradiscal pressure, and facet force variables under physiological loading. A validated three-dimensional finite element model of the human intact cervical spine (C2-T1) was used. The intact spine was modified to simulate CDAs at C5-C6. Hybrid loading with a follower load of 75 N and moments under flexion, extension, and lateral bending of 2 N·m each were applied to intact and CDA spines. From this work, it was found that at the index level, all CDAs except the Bryan disc increased ROM, and at the adjacent levels, motion decreased in all modes. The largest increase occurred under the lateral bending mode. The Bryan disc had compensatory motion increases at the adjacent levels. Intradiscal pressure reduced at the adjacent levels with Mobi-C and Secure-C. Facet force increased at the index level in all CDAs, with the highest force with the Mobi-C. The force generally decreased at the adjacent levels, except for the Bryan disc and Prestige LP in lateral bending. This study demonstrates the influence of different CDA designs on the anterior and posterior loading patterns at the index and adjacent levels with head supported mass type loadings. The study validates key clinical observations: CDA procedure is contraindicated in cases of facet arthroplasty and may be protective against adjacent segment degeneration.

The appropriate hybrid surgical strategy in three-level cervical degenerative disc disease: a finite element analysis

ObjectiveThe purpose of this FE study was to analyze the biomechanical characteristics of different HS strategies used in the treatment of three-level CDDD (one-level CDA and two-level ACDF).MethodsWe validated the FE model of an intact cervical spine established by transferring the data, collected by 3D CT scan, to the FE software ABAQUS and comparing these data with the data from published studies. Then, the FE model of hybrid surgery was reconstructed to analyze the range of motion (ROM), facet joint force, and stress distribution on an ultrahigh molecular weight polyethylene (UHMWPE) core.ResultsThe current cervical FE model was able to measure the biomechanical changes in a follow-up hybrid surgery simulation. The total ROM of the cervical HS models was substantially decreased compared with the total ROM of the intact group, and the M2 (C3/4 ACDF, C4/5 CDA, and C5/6 ACDF) model had the closest total ROM to the intact group, but the facet joint force adjacent to the treatment levels showed very little difference among them. The stress distribution showed noticeable similarity: two flanks were observed in the center core, but the inlay of M2 was more vulnerable.ConclusionsThrough the comparison of ROM, the facet joint force after CDA, and the stress distribution of the prosthesis, we find that M2 model has a better theoretical outcome, especially in preserving the maximum total ROM.

Correlation between compression depth and compressive stress of the anteroposterior cervical spinal cord in different sports positions

Objective To explore the relationship between the compression depth and compressive stress of the anterior and posterior cervical spinal cord in different sports positions. Methods Specimens of ten intact fresh cervical spine (C1-T1) from adult cadaver were collected. In order to simulate cervical disc degeneration and abnormal ligamentum flavum, we placed two hemispherical steel balls into the anterior and posterior side of the cervical spinal cord through the bone window of the C4, 5. The measurement was conducted in 10%, 20%, 30%, 40%, 50%, and 60% of the sagittal diameter for the compressive stress of the anterior and posterior cervical spinal cord under different compression depths of flexion, neutral, and posterior extension. Results The anterior depth of a certain pressure with the posterior pressure depth was increasing in neutral position, the stress on the anterior of the cervical cord-meningeal complex (CCMC) had no significant change, while the stress on the posterior of the CCMC increased greatly with the increasing of the degree of canal occlusion. The stress on the posterior of the CCMC varied insignificantly between 10% and 20% depth of canal occlusion (P>0.05). However, there was remarkable significance among 30% and 60% (P 0.05). However, there was remarkable significance among 20% and 60% (P 0.05). However, there was remarkable significance among 30% and 60% (P 0.05). However, there was remarkable significance among 20% and 60% (P<0.05). The stress on the posterior of the CCMC had no significant change. Compared with the neutral position, the anterior flexion position and the posterior extension position had different trends in the compressive stress in the anterior and posterior aspect of the cervical spinal cord. Conclusion The stress on the anterior and the posterior of the CCMC has a closely nonlinear relationship with the depth of canal occlusion. With the increase of the depth of canal occlusion, the stress is increasing, especially running over the 30% depress of canal occlusion under neutral position. However, the stress is increased, especially running over the 20% depress of canal occlusion under the flexion and extension position. Key words: Spinal cord; Stress, mechanical; Posture; Biomechanics

Anatomic morphology and clinical significance of intraforaminal ligaments of the cervical spine.

The cause of cervical spondylotic radiculopathy could be related to the intraforaminal ligaments (IFLs) of the cervical spine. The aim of this study is to identify and describe the IFLs and assess their clinical significance. Six intact cervical spine specimens from adult embalmed cadavers were dissected to expose the cervical nerve roots and their surrounding intraforaminal tissues fully. From the C1-C2 to the C7-T1 intervertebral foramina (IVF), the connective structures between each nerve root and its surrounding foraminal wall were examined under a surgical microscope. The morphology, number, and attachment points of the IFLs of each segment were documented, and the length, width, or diameter and thickness of the ligaments were measured with a vernier caliper. IFLs were observed in all 84 IVFs of the cervical spine. According to their locations, they can be divided into two categories: the first is entrance-zone IFLs, which are radially distributed around the nerve root; the second is mid-zone IFLs, which are thin, strip-shaped fibrous tissues intertwined around the nerve roots, the number of ligaments being considerable but difficult to quantify. Ligament structures have been identified in the IVF of the cervical spine. Under physiological conditions, they could be protective in maintaining the position, shape, and function of nerve roots. However, under pathological conditions, the IFLs of the cervical spine could aggravate the symptoms of cervical nerve root radicular pain associated with other types of compression. Clin. Anat. 32:654-660, 2019. © 2019 Wiley Periodicals, Inc.

Cervical Medial Branch Block Volume Dependent Dispersion Patterns as a Predictor for Ablation Success: A Cadaveric Study.

Neck pain is one of the most common causes of chronic pain and the fourth leading cause of disability worldwide; it is estimated that between 36% and 67% of this pain is due to facet arthropathy. For patients who have pain refractory to conservative treatments literature supports management with diagnostic cervical medial branch blocks (MBBs) to identify the associated facet innervation as the source of pain followed by therapeutic radiofrequency ablation (RFA) of the identified nerves. Cervical RFA has good published outcomes; however, the procedure is dependent upon the specificity of the diagnostic block to achieve maximal success. Currently, this prerequisite test has false positive rates between 27% and 63% and recent studies have shown that this may, in part, be a consequence of currently accepted injection volumes of 0.50 mL or more, which may decrease the sensitivity of MBBs. To evaluate the possible differences in volume dispersion between 0.25 and 0.50 mL of injectate during cervical MBBs. Cadaveric study. An academic medical center in the United States. Not applicable. This was a cadaveric study in which six subjects were chosen with intact cervical spines. Cervical MBB were performed bilaterally at the midcervical spine, using a posterior approach under fluoroscopic guidance. 0.25 or 0.50 mL of a 9:1 solution of Omnipaque 180 mg iodine/mL and 1% medical grade methylene blue were administered on the left and right sides, respectively. Postinjection computed tomography (CT) imaging and gross dissection were performed to assess injectate spread. Outcome measures after using commonly injected volumes for cervical MBB, included visualized and measured spread (by CT and gross dissection) of cervical medial branch blocks, coating adjacent structures not targeted by RFA. Postinjection CT imaging and cadaveric dissection demonstrated that, although both volumes adequately coated the medial branches, the 0.50 mL cohort reliably spread dorsally to superficial muscles (splenius) and nerves distant from the targeted nerves (dorsal motor branches to splenius), whereas the 0.25 mL injectate cohort was contained in the deep and intermediate muscular cervical layers directly juxtaposed to the targeted cMBBs. Results suggest that 0.50 mL injections of local anesthetic during cervical MBBs contacts many nonintended targets, thus decreasing the specificity of a targeted diagnostic cervical MBB. Furthermore, we demonstrated that 0.25 mL of injectate reliably bathed the cervical medial branches without extensive extravasation. This indicates that there would potentially be fewer local anesthetic effects on distant tissues, increasing the specificity of cervical MBBs and likely improving RFA planning.

Enhancing Evaluation of Cervical Spine: Thresholds for Normal CT Relationships in the Subaxial Cervical Spine.

Very little normative computed tomography (CT) scan data exist defining expected relationships of vertebral structures in the intact cervical spine. Better understanding of normal relationships should improve sensitivity of injury detection, particularly for facet subluxation. The purpose of this paper was to describe the normal anatomical relationships and most sensitive measurements to detect abnormal alignment in the subaxial cervical spine. A group of 30 CT scans with no documented cervical spine injury were utilized from an established database in a trauma population. Twenty-two anatomical measurements were made for each level of the subaxial cervical spine using Microview software. For the purposes of measurement, the upper confidence limit of normal was reported as two standard deviations from the mean. The novel, CT based measurements of bone articulation were generally smaller and had lower confidence intervals compared to traditional radiographic measurements of midline structures (such as interspinous distance, interlaminar widening, disc space widening). The upper limit of normal of facet joint height was reported (1.54 mm anterior, 1.27 mm posterior, and 2.0 mm midportion), which may help identify distractive-flexion injuries. The upper limit of normal vertebral translation (2.0 mm) was also reported to identify translation/rotation injuries. Normal CT measurements for the subaxial cervical spine, especially in the facets, were found to have small confidence limits and variation. Based upon these findings, we conclude that facet measurements and translation may be better screening tools than traditional radiographic criteria based upon midline structures. Using these measurements may improve detection of cervical spine injuries warranting further imaging or investigation and reducing missed injuries. Improved understanding of normal anatomic measures in the subaxial spine will allow for better screening and identification of injuries.

Wednesday, September 26, 2018 7:35 AM–9:00 AM ePosters: P14. Variations among human spine segments and their relationships to in vitro kinematics: a retrospective analysis of experimental data including 581 cervical motion segments from 147 donor spines

BACKGROUND CONTEXT Kinematic data from in vitro flexibility tests involving cadaveric spines are often used to validate finite element models of human spine segments. However, data describing relationships between motion segment features (ie, dimensions of vertebrae and discs, subject height) and kinematics are lacking. PURPOSE To retrospectively investigate the relationships between cadaveric cervical spinal motion segments and their biomechanical characteristics, including coupled motion. STUDY DESIGN/SETTING Standard nondestructive in-vitro flexibility tests were performed on intact cervical spine segments (Occ-C3 and C3-T1). Relationships between donor spine features and in vitro kinematic parameters were studied using Pearson correlation and multiple regression analyses. PATIENT SAMPLE A total of 581 cadaveric cervical motion segments from 147 donor spines [86M/61 F, range: 20-69years, mean age 53.5+10.6years, BMD 0.558+0.101 g/cm2, mean height 173.4+12.0 cm]. OUTCOME MEASURES Spinal flexibility of intact motion segments were assessed using intervertebral mean range of motion (ROM) during flexion–extension (FE), lateral bending (LB, average right and left), and axial rotation (AR, average right and left). Coupled motion (CM), that is LB during AR (LB/AR) and AR during LB (AR/LB) were also assessed. METHODS General spine tissue donor information (age, gender, height, and weight at time of death) was obtained from medical histories provided by tissue banks. Bone mineral densities (BMD) were obtained from DEXA scans. Dimensions of vertebrae and discs were measured using ImageJ. Kinematic data were retrieved from studies involving intact testing of the fresh cervical spine segments (Occiput-T1), with all tests performed in the same lab using the same protocol. Loads of 1.5 Nm were applied while optoelectronically measuring intervertebral rotations in three planes (FE, LB and AR) at all spinal levels. Relationships between donor information (vertebrae and disc dimensions, subject height, weight, gender), bone quality (BMD) and kinematic data (ROM, CF LB/AR and CF AR/LB) were studied using Pearson correlation and multiple regression analyses (p RESULTS Overall values for ROM for intact motion segments were within typical values as reported in the literature. There were significant negative correlations between BMD and ROM, starting at C4–C5 and continuing caudally (R .4). Multiple linear regression analysis showed that ROM of cervical motion segments can be predicted using relationships between subject cervical level, gender, age, weight and/or BMD [FL-EX: R=0.321, P CONCLUSIONS Significant relationships exist between cervical spine segments’ dimensions, BMD and biomechanical properties (ROM and CM) at mid- and lower cervical levels. These relationships are of value during the validation process of finite element models involving human cervical spine segments, especially in studies focusing on motion preservation.

The Influence of Artificial Cervical Disc Prosthesis Height on the Cervical Biomechanics: A Finite Element Study.

Artificial cervical disc replacement is expected to maintain normal cervical biomechanics. At present, the effect of the Prestige LP prosthesis height on cervical biomechanics has not been thoroughly studied. This finite element study of the cervical biomechanics aims to predict how the parameters, like range of motion (ROM), adjacent intradiscal pressure, facet joint force, and bone-implant interface stress, are affected by different heights of Prestige LP prostheses. The finite element model of intact cervical spine (C3-C7) was obtained from our previous study, and the model was altered to implant Prestige LP prostheses at the C5-C6 level. The effects of the height of 5, 6, and 7 mm prosthesis replacement on ROM, adjacent intradiscal pressure, facet joint force, as well as the distribution of bone-implant interface stress were examined. ROM, adjacent intradiscal pressure, and facet joint force increased with the prosthesis height, whereas ROM and facet joint force decreased at C5-C6. The maximal stress on the inferior surface of the prostheses was greater than that on the superior surface, and the stresses increased with the prosthesis height. The biomechanical changes were slightly affected by the height of 5 and 6 mm prostheses, but were strongly affected by the 7-mm prosthesis. An appropriate height of the Prestige LP prosthesis can preserve normal ROM, adjacent intradiscal pressure, and facet joint force. Prostheses with a height of ≥2 mm than normal can lead to marked changes in the cervical biomechanics and bone-implant interface stress.

Autologous Bone Harvest in Anterior Cervical Spine Surgery: A Quantitative and Qualitative InVitro Analysis of Cadaveric Tissue.

The cervical spine may be used as a harvesting site of local autograft material during anterior cervical discectomy and fusion procedures. We analyzed the quality and composition of bone grafts obtained from different parts of the cervical vertebrae in a cadaveric model. Five fresh adult human cadavers with intact cervical spines were used. Using a Smith-Robinson anterior approach to expose C4-5 and C5-6 vertebrae, samples from 4 vertebral sites were harvested under a microscope. Anterior osteophytes were removed piecemeal by a Leksell rongeur (sample A). A high-speed burr was used to drill the endplates of C4-5 and C5-6 (sample C) and uncovertebral joints of C4-5 (sample B) and C5-6 (sample D). Then 20 slides (4 per cadaver) were prepared and analyzed. Tissue fragmentation was associated with use of the high-speed burr. Sample A had minimal tissue fragmentation. Samples B-D showed moderate to high fragmentation. Cartilage was found in all samples. Of the 20 slides, 6 contained soft tissues (sample A in 4, sample D in 2). Disc material was identified in 6 slides (sample A in 1, sample B in 4, sample D in 1). Sample A had the greatest number of intact osteocytes and chondrocytes, and sample B had the least. Anterior osteophytes provide the highest number of osteocytes, with the highest osteocyte/chondrocyte ratio. Osteocyte viability is a function of vertebral body site and collection technique, with fragmentation caused by use of a high-speed burr decreasing the number of viable osteocytes.

Intubation biomechanics: validation of a finite element model of cervical spine motion during endotracheal intubation in intact and injured conditions.

OBJECTIVE Because of limitations inherent to cadaver models of endotracheal intubation, the authors' group developed a finite element (FE) model of the human cervical spine and spinal cord. Their aims were to 1) compare FE model predictions of intervertebral motion during intubation with intervertebral motion measured in patients with intact cervical spines and in cadavers with spine injuries at C-2 and C3-4 and 2) estimate spinal cord strains during intubation under these conditions. METHODS The FE model was designed to replicate the properties of an intact (stable) spine in patients, C-2 injury (Type II odontoid fracture), and a severe C3-4 distractive-flexion injury from prior cadaver studies. The authors recorded the laryngoscope force values from 2 different laryngoscopes (Macintosh, high intubation force; Airtraq, low intubation force) used during the patient and cadaver intubation studies. FE-modeled motion was compared with experimentally measured motion, and corresponding cord strain values were calculated. RESULTS FE model predictions of intact intervertebral motions were comparable to motions measured in patients and in cadavers at occiput-C2. In intact subaxial segments, the FE model more closely predicted patient intervertebral motions than did cadavers. With C-2 injury, FE-predicted motions did not differ from cadaver measurements. With C3-4 injury, however, the FE model predicted greater motions than were measured in cadavers. FE model cord strains during intubation were greater for the Macintosh laryngoscope than the Airtraq laryngoscope but were comparable among the 3 conditions (intact, C-2 injury, and C3-4 injury). CONCLUSIONS The FE model is comparable to patients and cadaver models in estimating occiput-C2 motion during intubation in both intact and injured conditions. The FE model may be superior to cadavers in predicting motions of subaxial segments in intact and injured conditions.

A Novel Anterior Transpedicular Screw Artificial Vertebral Body System for Lower Cervical Spine Fixation: A Finite Element Study.

A finite element model was used to compare the biomechanical properties of a novel anterior transpedicular screw artificial vertebral body system (AVBS) with a conventional anterior screw plate system (ASPS) for fixation in the lower cervical spine. A model of the intact cervical spine (C3-C7) was established. AVBS or ASPS constructs were implanted between C4 and C6. The models were loaded in three-dimensional (3D) motion. The Von Mises stress distribution in the internal fixators was evaluated, as well as the range of motion (ROM) and facet joint force. The models were generated and analyzed by mimics, geomagic studio, and ansys software. The intact model of the lower cervical spine consisted of 286,382 elements. The model was validated against previously reported cadaveric experimental data. In the ASPS model, stress was concentrated at the connection between the screw and plate and the connection between the titanium mesh and adjacent vertebral body. In the AVBS model, stress was evenly distributed. Compared to the intact cervical spine model, the ROM of the whole specimen after fixation with both constructs is decreased by approximately 3 deg. ROM of adjacent segments is increased by approximately 5 deg. Facet joint force of the ASPS and AVBS models was higher than those of the intact cervical spine model, especially in extension and lateral bending. AVBS fixation represents a novel reconstruction approach for the lower cervical spine. AVBS provides better stability and lower risk for internal fixator failure compared with traditional ASPS fixation.