Insulator Devices Research Articles

Comprehensive Mapping and Dynamic Monitoring of the Temporal Branch of the Facial Nerve in Complex Cranial Reconstruction Surgery and Revision Cranioplasty.

Facial nerve (FN) injury is a significant risk during complex cranial reconstruction surgeries, especially in revision cases where normal anatomy is distorted. The authors introduce a technique to mitigate FN injury, including preoperative FN mapping, intraoperative FN mapping, and continuous FN monitoring. Preoperative mapping uses a handheld ball-tip stimulator to elicit compound muscle action potentials (CMAP) in the frontalis muscle. Needle electrodes are placed above the orbital margin to record responses, starting at the stylomastoid foramen and extending until the entire temporal branch is mapped. Intraoperatively, continuous mapping is achieved using an electrified insulated suction device, allowing dynamic mapping during soft tissue dissection. Continuous monitoring involves placing stimulation electrodes near the stylomastoid foramen and recording CMAP responses from the frontalis and orbicularis oculi/orbicularis oris muscles. The authors tested this technique in 5 patients. The authors successfully mapped the temporal branch of the FN with isolated frontalis CMAP recordings in all patients. Intraoperative FN mapping and continuous monitoring were successfully performed in all cases. Two patients experienced complete cessation of FN CMAPs, which resumed upon loosening the tension on the myocutaneous flap held by fishhooks. One patient showed a 39% decrement in frontalis CMAP that did not recover. Despite these issues, all patients had intact FN function postoperatively and at follow-up. Our technique shows promise in mitigating FN injury during complex cranial reconstruction and cranioplasty revision surgery. Further research with a larger cohort is needed to confirm efficacy and statistical significance.

DFT study of Cun (n = 1–3) cluster-modified WSe2 monolayers for the detection of SF6 decomposition gases (H2S, SO2, SOF2 and SO2F2)

The role of SF6 in gas-insulated equipment is crucial for insulation and arc extinction. When subjected to electrical faults, thermal faults, and mechanical failures in insulation devices, SF6 can decompose into H2S, SO2, SOF2, and SO2F2. This study conducted first-principles simulations to analyze the effect of Cun (n = 1–3) cluster-modified monolayer WSe2 on sensing H2S, SO2, SOF2, and SO2F2 gases during SF6 decomposition. The optimal doping positions of Cun-WSe2 clusters at n = 1, 2, and 3 were determined, showcasing their superiority over pure WSe2 in terms of band gap, frontier orbitals, and density of states. Subsequently, a detailed investigation was carried out on the adsorption effects of the four gases at the optimal doping positions, including parameters such as adsorption distance, adsorption energy, charge transfer, differential charge density, and density of states. It was found that when the number of copper atoms in the cluster increased to 3, the banding energy sharply rose to -2.395 eV. Simulation results demonstrated the adsorption behavior of H2S on Cun (n = 1–3)-WSe2 demonstrates remarkable affinity, with an increasing adsorption energy as the number of Cu atoms rises. Notably, Cun (n = 1–3)-WSe2 exhibits favorable desorption times for SO2. At 378 K, the desorption time for SO2@Cu3-WSe2 is 14.7 s. At 498 K, desorption times for SO2@Cu1-WSe2 and SO2@Cu2-WSe2 are 7.59 s and 2.85 s, respectively. When the number of copper atoms is 2, the cluster-modified system desorbs SOF2 at room temperature in only 0.89 s. Moreover, Cun (n = 1–3)-WSe2 displays strong adsorption towards SO2F2, characterized by prolonged desorption times, rendering it a promising adsorbent for SO2F2 removal. This study aims to highlight the adsorption effects of different numbers of Cu atomic clusters in the Cun-WSe2 system on SF6 decomposition gas, further advancing research for developing high-performance SF6 decomposition gas sensors.

Machine learning assisted understanding of the layer-thickness dependent thermal conductivity in fluorinated graphene

Manipulating thermal conductivity (κ) plays vital role in high-performance thermoelectric conversion, thermal insulation and thermal management devices. In this work, we using the machine learning-based interatomic potential and the phonon Boltzmann transport equation to systematically investigate layer thickness dependent κ of fluorinated graphene (FG). We show that the lattice κ of FG can be significantly decreased with Bernal bilayer stacking. Surprisingly, the further increasing of stacking layer can no longer affect the κ, however, the κ is increased in the bulk configuration. The variation of κ can be attributed to the crystal symmetry change from P-3m1 (164) at single layer to P3m1 (156) at multilayer. The decreasing crystal symmetry from single layer to bilayer resulting stronger phonon scattering and thus leading a lower κ. Moreover, we also show that the contribution of acoustic mode to κ decreases with the increase of layers, while the contribution of optical mode to κ is increased with increasing layers. These results provide a further understanding for the phonon scattering mechanism of layer thickness dependent κ.

Selective and quasi-continuous switching of ferroelectric Chern insulator devices for neuromorphic computing.

Quantum materials exhibit dissipationless topological edge state transport with quantized Hall conductance, offering notable potential for fault-tolerant computing technologies. However, the development of topological edge state-based computing devices remains a challenge. Here we report the selective and quasi-continuous ferroelectric switching of topological Chern insulator devices, showcasing a proof-of-concept demonstration in noise-immune neuromorphic computing. We fabricate this ferroelectric Chern insulator device by encapsulating magic-angle twisted bilayer graphene with doubly aligned h-BN layers and observe the coexistence of the interfacial ferroelectricity and the topological Chern insulating states. The observed ferroelectricity exhibits an anisotropic dependence on the in-plane magnetic field. By tuning the amplitude of the gate voltage pulses, we achieve ferroelectric switching between any pair of Chern insulating states in the presence of a finite magnetic field, resulting in 1,280 ferroelectric states with distinguishable Hall resistance levels on a single device. Furthermore, we demonstrate deterministic switching between two arbitrary levels among the record-high number of ferroelectric states. This unique switching capability enables the implementation of a convolutional neural network resistant to external noise, utilizing the quantized Hall conductance levels of the Chern insulator device as weights. Our study provides a promising avenue towards the development of topological quantum neuromorphic computing, where functionality and performance can be drastically enhanced by topological quantum materials.

Even-Odd Layer-Dependent Exchange Bias Effect in MnBi2Te4 Chern Insulator Devices.

Magnetic topological materials with coexisting magnetism and nontrivial band structures exhibit many novel quantum phenomena, including the quantum anomalous Hall effect, the axion insulator state, and the Weyl semimetal phase. As a stoichiometric layered antiferromagnetic topological insulator, thin films of MnBi2Te4 show fascinating even-odd layer-dependent physics. In this work, we fabricate a series of thin-flake MnBi2Te4 devices using stencil masks and observe the Chern insulator state at high magnetic fields. Upon magnetic field training, a large exchange bias effect is observed in odd but not in even septuple layer (SL) devices. Through theoretical calculations, we attribute the even-odd layer-dependent exchange bias effect to the contrasting surface and bulk magnetic properties of MnBi2Te4 devices. Our findings reveal the microscopic magnetic configuration of MnBi2Te4 thin flakes and highlight the challenges in replicating the zero magnetic field quantum anomalous Hall effect in odd SL MnBi2Te4 devices.

Dual-Step Redox Engineering of 2D CoNi-Alloy Embedded B, N-Doped Carbon Layers Toward Tunable Electromagnetic Wave Absorption and Light-Weight Infrared Stealth Heat Insulation Devices.

2D layered metallic graphite composites are promising electromagnetic wave absorption materials (EWAMs) for their combined properties of abundant interlayer free spaces, rich metallic polarized sites, and high conductivity, but the controllable synthesis remains rather challenging. Herein, a dual-step redox engineering strategy is developed by employing cobalt boron imidazolate framework (Co-BIF) to construct 2D CoNi-alloy embedded B, N-doped carbon layers (2D-CNC) as a promising EWAM. In the first step, a chemical etching oxidation process on Co-BIF is used to obtain an optimized 2D-CoNi-layered double hydroxide (2D-CoNi-LDH) intermediate and in the second, high-temperature calcination reduction is implemented to modify graphitization of the degree of the 2D-CNC. The obtained sample delivers superior reflection loss (RLmin) of -60.1dB and wide effective absorption bandwidth (EAB) of 6.24GHz. The synergy mechanisms of interfacial/dipole polarization and magnetic coupling are in-depth evidenced by the hologram and Lorentz electron microscopy, revealing its significant contribution on multireflection and impedance matching. Further theoretical evaluation by COMSOL simulation in different fields based on the dynamic loss process toward the test ring reveals the in situ EW attenuation process. This work presents a strategy to develop multifunctional light-weight infrared stealthy aerogel with superior pressure-resistant, anti-corrosion, and heat-insulating properties for future applications.

Effectiveness of building envelope parameters and adopting PV panels to reduce reliance on local generators in hot-dry climate

The growing energy demand, associated with the inability of the current infrastructure to satisfy this demand, has presented numerous challenges in Iraq's electricity sector. As a result, there has been an increased dependence on local diesel generators to mitigate power outages in homes. However, these generators raise environmental concerns and are associated with high operating CO₂ emissions. Here, using the DesignBuilder and EnergyPlus simulation software, the effectiveness of different building envelope modifications and photovoltaic panels as alternative energy sources was examined. Specifically, the impact of wall and roof insulation, window glazing, and shading devices on energy efficiency was analyzed. The results indicated that roof insulation is the most effective in reducing energy consumption by 28.8%, followed by wall insulation by 13.01%, while the effect of windows glazing and shading devices was insignificant. Furthermore, the installation of solar panels led to a significant reduction in energy demand by 53.6%, thereby decreasing operating carbon dioxide emissions and providing a practical alternative to the use of local generators. Our study offers valuable insights into the design of energy-efficient residential buildings in hot and dry climates. It highlights the importance of selecting appropriate building materials and integrating renewable energy sources, presenting a more environmentally effective solution to mitigate energy shortages.

Preparation of BN@SiO2 nanofiber ceramic aerogel with ultralight, wave-transparent and heat-insulating for microwave sintering furnace

Thermal insulation devices play an extremely important role in enhancing microwave heating efficiency. However, existing wave-transparent insulation materials often exhibit high heat storage, low microwave transmittance at high temperatures, and poor oxidation and thermal shock resistance, hindering high-temperature applications for microwave sintering. To address this issue, we developed an ultralight and wave-transparent BN@SiO2 aerogel, which was fabricated through the in situ growth of SiO2 on the surfaces of BN fibers. The resulting composite aerogel demonstrated excellent high-temperature oxidation resistance and an impressively low density of 0.07 g/cm3. Furthermore, the dielectric constant of the BN@SiO2 aerogel ranged from 2.58 to 2.80, and its dielectric loss tangent was as low as 5.13 × 10−3–7.98 × 10−3 within the 2–10 GHz frequency range. The successful synthesis of BN@SiO2 aerogel provides new progress and research ideas for the development of wave transparent and thermal insulation materials.

Pd-Adsorbed SiN3 Monolayer as a Promising Gas Scavenger for SF6 Partial Discharge Decomposition Components: Insights from the First-Principles Study.

Gas-insulated switchgear (GIS) equipment must be protected by detecting and eliminating the toxic SF6 partial discharge decomposition components. This study employs first-principles calculations to thoroughly investigate the interaction between a Pd-adsorbed SiN3 monolayer (Pd-SiN3) and four typical SF6 decomposition gases (H2S, SO2, SOF2, and SO2F2). The study also investigates the associated geometric, electrical, and optical characteristics along with the sensing sensitivity and desorption efficiency. The ab initio molecular dynamics (AIMD) simulations demonstrated the favorable stability of the Pd-SiN3 monolayer. Furthermore, the Pd-SiN3 monolayer exhibited strong chemisorption behavior toward H2S, SO2, SOF2, and SO2F2 gases because of the higher adsorption energies of -2.717, -2.917, -2.457, and -2.025 eV, respectively. Furthermore, significant changes occur in the electronic and optical characteristics of the Pd-SiN3 monolayer following the adsorption of these gases, resulting in remarkable sensitivity of the Pd-SiN3 monolayer in relation to electrical conductivity and optical absorption. Meanwhile, all of these gas adsorption systems exhibited extremely long recovery times. The aforementioned theoretical findings suggest that the Pd-SiN3 monolayer has the potential to be an effective gas scavenger for the storage or removal of the SF6 decomposition components. Additionally, it might function as a reliable one-time sensor for detecting these gases. The results potentially provide valuable theoretical guidance for maintaining the normal operation of the SF6 insulation devices.

Effect of hydrostatic pressure on thermal transport properties of Tl3XSe4 (X = V, Ta, Nb): A First-Principles study

Recently, Tl3XSe4 (Abbreviated as TlXSe; X = V, Ta, Nb) crystals have been found to exhibit ultra low lattice thermal conductivities κl (∼0.15 W/mK at 300 K), ultra high figure of merit ZT (3 ∼ 4 at 300 K) and thus show great potentials in the fields of thermoelectric and engineering thermal management. Generally, thermal insulation devices and thermoelectric devices are used in harsh working environment, such high/low temperature, high pressure and so on. In order to further evaluate the industrial application values of TlXSe crystals, in this work, we explored their thermal transport behaviors under high pressures based on first-principles calculations method. The results show that TlXSe materials can maintain structural stability under high pressure up to 8 GPa, and their κl values increase about 2 ∼ 4 times under the high pressure of 0 ∼ 8 GPa. The increases of κl values are mainly due to the co-coupling effects of the increased phonon harmonicity and decreased phonon anharmonicity caused by high pressures. For all that, the κl values of TlXSe compounds are still below 0.5 W/mK at 300 K under the high pressure of 0 ∼ 8 GPa, which are also lower than those of most thermal insulation and thermoelectric materials. This work highlights the future potential applications of TlXSe crystals in thermal management, thermoelectric and many other fields, and thus provides useful information for further experimental and theoretical studies.

Development of Carbon Nanotubes–Graphene–Polydimethylsiloxane Composite Film with Excellent Electrothermal Performance

Low power density and low heating rate are the key constraints for the development of conductive polymer materials in the field of electric heating. The carbon nanotubes (CNTs)–graphene (GR)–polydimethylsiloxane (PDMS) composite film was prepared by vacuum filtration and spin coating to solve the problem in this study. Moreover, an AC electric field was used to orient the CNTs to enhance the electrothermal performance. The structure and properties of composite films were analyzed. The results show that the composite film with CNT:GR = 2:1 has the lowest permeation threshold, and can heat up within 30 s and stabilize at 260 °C at 10 V. The electric field-oriented CNTs reduced the insulating polymer layer, increasing the heating rate of the composite film by 1.2 times, and increasing the theoretical thermal conductivity. The flexible electrothermal composite film prepared in this study can be used in thermal insulation, deicing, and wearable electronic devices.

Applications of ventilation-enabling sound insulation devices based on mock-up test findings

Road traffic, railway and industrial noise sources are main challenges in maintaining satisfying acoustical environment for living habitat in Hong Kong. Ventilation-enabling sound insulation devices has been introduced to Hong Kong residential development in the aim of striking a good balance between indoor ventilation and sound insulation. In the form of windows and balconies, the sound insulation devices were applied to mitigate the potential road traffic, railway, and fixed noise impacts. The sound insulation performances of the devices were verified in a 1:1 mock-up test and indicated by in-out difference, which contributed from the outdoor and indoor noise levels. The in-out difference of the sound insulation devices varies with the adopted spectrum, depending on flat layout configurations. The enhancing performance of applied acoustic material to the sound insulation devices, and that of applied acoustic fin adjacent to the devices are also studied.

Study of rib protection devices based on resistant muffler theory for transcostal focused ultrasound therapy

High-intensity focused ultrasound (HIFU) is one of the effective means of treating cancer. One of the current challenges in HIFU treatment is how to minimize thermal damage to the rib during transcostal HIFU treatment and ensure that sufficient energy is delivered to the target area. In this paper, a sound insulation device mounted in front of the rib is proposed to address this challenge. The device is designed based on resistant anechoic theory, combining both reflective and resonant sound energy-blocking mechanisms to enhance the transmission loss and filter bandwidth. The structural parameters of the device are optimized using an orthogonal test method. A finite element method was used to simulate the sound and temperature fields of the sound insulation device with and without different rib spacings. The simulation results demonstrate a significant decrease in sound pressure at the ribs under the protection of the sound insulation device, with no significant difference in sound pressure at the target area. Consequently, the temperature at the ribs decreases, while the temperature at the target area tissue is guaranteed. Furthermore, transcostal HIFU experiments are conducted using real pig ribs and the experimental results validate the accuracy of the simulation results.

Bibliometric and Co-Occurrence Study of Process System Engineering (PSE) Applied to the Polyvinyl Chloride (PVC) Production.

PVC is widely used in packaging, electrical insulation, and medical devices due to its versatility owing to its resistance, incombustible and barrier properties as well as affordable cost. In the present study, bibliometric and co-occurrence analyses are proposed to identify trends, gaps, future directions, and challenges regarding process system engineering (PSE) applied to the production process of PVC using VOSviewer as a tool for analyzing the data obtained from SCOPUS. A mapping of different topics alluding to simulation of PVC production was provided to gain a better insight into the development of the topic and its progression. The findings indicate that the literature on this topic falls into five different clusters: modeling and simulation of PVC production, process control and optimization, and optimization strategies of the process. From a co-occurrence study we identified that mathematics and statistics applied to polymer chemistry, separation phenomena, and polymer production are the main areas of interest for further research. The trends suggest that Monte Carlo and numerical simulation can contribute to a deeper understanding of PVC's properties and behavior. In addition, the focus on plastics and microplastics reflects concerns about the environmental impact. A bibliometric study evidenced that PSE provides the tools for improvement in PVC production processes by employing advanced process engineering techniques. Modelling and new algorithms for simulation methods of continuous polymerization processes are important to enhance accuracy and efficiency across various applications. The study also proposes a research agenda for future researchers working in the field of the use of PSE applied to the PVC production process.

Field‐Free Switching and Enhanced Electrical Detection of Ferrimagnetic Insulators Through an Intermediate Ultrathin Ferromagnetic Metal Layer

AbstractPerpendicularly magnetized ferrimagnetic insulators offer great potential for the development of fast and energy‐efficient spintronic devices. However, a major challenge for these devices is the requirement of an auxiliary magnetic field to achieve spin‐orbit torque (SOT)‐driven magnetization switching, along with the extremely small electric read‐out signal from the adjacent heavy metal layer. In this work, an approach by introducing an ultrathin Co layer primarily with in‐plane magnetization at the interface of the Tm3Fe5O12/Pt bilayers, which enables field‐free deterministic switching of the perpendicular Tm3Fe5O12 layer is demonstrated. Meanwhile, it is observed that a large anomalous Hall resistance readout signal from the coupling‐induced perpendicular component of the interfacial Co, which is nearly two orders of magnitude larger than that observed in Tm3Fe5O12/Pt bilayers. The crucial role played by the Co layer in modifying the SOT is elucidated. This research represents a significant step toward the practical implementation of ferrimagnetic insulator devices.

Hilbert Fractal Antenna for Abnormal Discharge Detection of Transmission Equipment

The safe and stable operation of the power system can ensure people’s basic electricity needs. It also plays an important role in energy security and economic development and can contribute to environmental protection and energy conservation. If there are problems in the power system, it will not only affect people’s normal life and work but also lead to power loss or waste, thereby exacerbating the impact on the environment. With the long-term operation of transmission equipment, insulation devices are aging, leading to frequent abnormal discharges and affecting the safety and stability of the power system. Therefore, timely detection and troubleshooting are necessary. When abnormal discharge occurs in transmission equipment, it will radiate radio frequency (RF) electromagnetic waves, which are mainly concentrated between 200 MHz and 300 MHz. RF antennas that can capture signals in this frequency band can be used for detection to determine whether abnormal discharge has occurred. This article uses the Hilbert fractal antenna as the research object to analyze the impact of different orders on antenna performance and optimizes the different feeding point positions of the antenna. Finally, the antenna structure for detecting abnormal discharge is obtained. By making an actual antenna and conducting experimental analysis, the discharge detection function of the designed antenna is verified.

Defect Induced Unconventional Ferromagnetism in Au Intercalated Bi2Se3 Nanocrystals for Spintronic Applications

AbstractBreaking time‐reversal symmetry through magnetic impurities has been a useful strategy for achieving exotic physical phenomena in topological insulators for a long time. In contrast, reports on achieving ferromagnetism in topological insulators by introducing non‐magnetic elements are very scarce. The present article illustrates Au ion implantation as an alternative tool to study the structural and magnetic properties in the Bi2Se3 nanocrystals grown by the chemical vapor deposition. The as‐grown pristine Bi2Se3 exhibits triangular and hexagonal plate‐like morphology, which undergoes structural distortion with increased Au ions. The room temperature Raman spectra show defect‐induced phonon softening with ion fluence. The non‐magnetic Bi2Se3 exhibit room temperature ferromagnetic hysteresis that originates from Bi vacancies which is verified from the density functional theory (DFT)calculations. The incorporation of Au ions initially decreases the magnetic moment up to the fluence 1 × 1014 ions cm−2 and enhances at higher fluences due to the formation of Au nanoclusters. The experimental and DFT results suggest a competition between the Se “4p” states and Au “5d” states for the non‐monotonic behavior of magnetic properties. The present work on Au intercalation in Bi2Se3 can pave the way to design artificial topological insulator devices for potential technological applications for future spintronics and quantum computations.

Study on interface insulation properties of Al2O3 epoxy composites using plasma jet‐fluorinated etching/SiOx deposition

AbstractDue to their superior mechanical and electrical characteristics, Al2O3 epoxy composites (Al2O3/EP) are extensively utilized in producing insulation devices. However, Al2O3/EP is prone to accumulating a large amount of charge under a direct current (DC), which threatens the operation of the power system. In this article, we conducted surface fluorinated etching and SiOx deposition on the material by atmospheric pressure plasma jet (APPJ). Various testing methods were used to investigate the impacts of plasma modification on the physicochemical characterization of Al2O3/EP, and the changes in superficial conductivity, flashover voltage, charge dissipation rate, and trap distribution were experimentally tested. The influences of two plasma modification methods on the physicochemical characterization of Al2O3/EP were analyzed. The enhancement mechanism of Al2O3/EP flash behavior by fluorinated etching and SiOx deposition is summarized. The findings demonstrate that the insulation behavior of Al2O3/EP results from a combination of a few dominant and multiple factors. Fluorinated etching enhances the degree of roughness and the relative proportion of the F element, provides chemically deep traps, and raises the flashover voltage by up to 19%. SiOx deposition boosts the dispersion of charges by forming SiOx layers on the surface, reducing the degree of roughness and increasing the content of the silicon–oxygen element, making it more difficult for charges to accumulate and increasing the flashover voltage by up to 15%. This study will reveal the internal relationship between gas–solid interface and surface flashover, and provide a possible scheme for suppressing surface flashover.Highlights Modifications substantially increase the flashover voltage. Modifications allow a wide range of interface parameters to be adjusted. The effects of modifications on physicochemical properties are compared. The enhancement mechanism of flashover voltage by modifications is compared. The overall effect of multiple factors on insulation properties is analyzed.

Simulation of Total Ionizing Dose Effects Technique for CMOS Inverter Circuit.

The total ionizing dose (TID) effect significantly impacts the electrical parameters of fully depleted silicon on insulator (FDSOI) devices and even invalidates the on-off function of devices. At present, most of the irradiation research on the circuit level is focused on the single event effect, and there is very little research on the total ionizing dose effect. Therefore, this study mainly analyzes the influence of TID effects on a CMOS inverter circuit based on 22 nm FDSOI transistors. First, we constructed and calibrated an N-type FDSOI metal-oxide semiconductor (NMOS) structure and P-type FDSOI metal-oxide semiconductor (PMOS) structure. The transfer characteristics and trapped charge distribution of these devices were studied under different irradiation doses. Next, we studied the TID effect on an inverter circuit composed of these two MOS transistors. The simulation results show that when the radiation dose was 400 krad (Si), the logic threshold drift of the inverter was approximately 0.052 V. These results help further investigate the impact on integrated circuits in an irradiation environment.

Analytical, numerical, and experimental methods to study thermo-elastic coupling inherent and vibration characteristics of a flexible rotor system

The thermal deformation of a flexible rotor system in a high-temperature environment causes changes in the inherent and vibration characteristics. A theoretical model of the flexible rotor was established based on the theory of thermal deformation, the assumed mode method, and the Lagrangian principle. The mode natural frequencies and shapes were explored in detail when the temperature of different nickel-based alloy rotor blades increased gradually (from 0 to 1200°C). The changes in the unstable speed points as the temperature gradually increased were studied based on the rotation speed–frequency diagram. In addition, experimental methods were performed. Mode and steady-state speed tests in a supported state were conducted. Mode experiments were completed on a five-blade rotor test rig with a thermal insulation device, and the acceleration frequency-domain signal showed that the natural frequency decreased with increasing temperature. Through steady-state speed experiments, it was found that the position of the unstable speed points moved forward, and the displacement amplitude increased after local heating.