Influence Of Target Thickness Research Articles

Numerical study on influence of target thickness on impact response of GFRP composites

Due to rise in threats like ballistic impacts, blast loading and vehicle collision in armored military vehicles, the demand for materials with high strength and enhanced energy absorption capacity has been increased. Applications of Fiber reinforced composites as armor material in military vehicles is being considered as one of the measures to reduce such threats. The focus of this work is to investigate the energy absorption capacity of a GFRP plates subjected to a rigid projectile with blunt-nosed at the intermediate velocity range by using non-linear finite element code LS-DYNA. It has been found that the numerically computed results of ballistic limit velocity and residual velocity, closely resemble the test results reported in the literature. With altering target thickness, it has also been explored how the energy absorption capacity, projectile's residual velocity, ballistic velocity limit and damage mechanism of composite. The numerical results make it evident that the target thicknesses have a significant impact on the target's ballistic resistance and delamination area.

A Numerical Study of Penetration in Concrete Targets by Eroding Projectiles of Different Materials

Numerical simulations have been performed to examine the effect of three different eroding rod materials on the penetration in concrete targets. Same kinetic energy is delivered to concrete target using cylindrical rods of Aluminium, Iron, and Copper of identical size. Impact velocities have been varied to keep the kinetic energy the same. Penetration characteristics like centerline interface velocity, penetrator deceleration, plastic strain in the target, and energy partitioning during penetration have been studied for the three different penetrator materials. In all three cases, penetration proceeds nearly hydrodynamically. It is seen that even though the steady-state penetration ceases before reaching the hydrodynamic limit, the secondary penetration takes the total penetration beyond the hydrodynamic value. Plastic strain in the target material is a measure of damage beyond the crater produced by penetration. The lateral extent of plastic strain in target is more for Aluminium penetrator compared to the other two. Energy partitioning during penetration provides details of the rate at which energy is entering into the target. Kinetic energy delivered to the target during impact is partitioned into internal energy and kinetic energy of the target. Finally, the influence of target thickness on the extent of plastic strain has been studied. The result shows that Aluminium penetrators inflict maximum damage to targets of finite thickness.

Numerical and experimental investigations on the effect of target thickness and solution treatment on the ballistic behaviour of AA7075 thick plates

The influence of target thickness and solution treatment on the ballistic behaviour of AA7075 targets has been investigated by both numerical and experimental methods. In numerical simulation, the target thickness was varied from 19 to 26 mm and an Ogive nose shaped projectile of 7.62 mm diameter with inlet velocities ranging between 800–875 m/s was considered. In order to justify the numerical observations, high velocity ballistic experiments were conducted on AA7075-T651 and the solution treated plates of various thicknesses (12, 16, 18, 20, 22 and 25 mm). For this experimental study, a deformable form projectile with dimensions of 7.62 × 51 mm and an inlet velocity of 850 ± 20 m/s was used. Microstructures of ballistic test samples were analysed using an optical microscope. Numerical analysis using ABAQUS predicted the minimum thickness required to resist complete penetration to be 20 mm in the case of AA7075 plates in the T651 condition, while experimental results showed it to be 21 mm. In the case of AA7075 solution treated plates, numerical simulation analysis predicted the minimum required plate thickness to resist complete penetration to be 24 mm, while the experimental results showed it to be 23 mm. Post ballistic microstructure analysis revealed that there was no change in the microstructure in the AA7075-T651 condition plates. Solution treated plates showed deformation of grains nearer to the impact region with the formation of adiabatic shear bands. In the case of the T651 plate, the mode of fracture was brittle, resulting in splinters, whereas it was petalling in the case of the solution-treated plates. The numerically predicted depth of penetration on both targets was reasonably close to experimental results with an average of 4% error.

Evaluation of the Effect of Source Geometry on the Output of Miniature X-ray Tube for Electronic Brachytherapy through Simulation.

The use of miniature X-ray source in electronic brachytherapy is on the rise so there is an urgent need to acquire more knowledge on X-ray spectrum production and distribution by a dose. The aim of this research was to investigate the influence of target thickness and geometry at the source of miniature X-ray tube on tube output. Five sources were simulated based on problems each with a specific geometric structure and conditions using MCNPX code. Tallies proportional to the output were used to calculate the results for the influence of source geometry on output. The results of this work include the size of the optimal thickness of 5 miniature sources, energy spectrum of the sources per 50 kev and also the axial and transverse dose of simulated sources were calculated based on these thicknesses. The miniature source geometric was affected on the output x-ray tube. The result of this study demonstrates that hemispherical-conical, hemispherical and truncated-conical miniature sources were determined as the most suitable tools.

Influence of target thickness on the release of radioactive atoms

Nowadays, intense exotic beams are needed in order to study nuclei with very short half-life. To increase the release efficiency of the fission products, all the target characteristics involved must be improved (e.g. chemical composition, dimensions, physicochemical properties such as grain size, porosity, density…). In this article, we study the impact of the target thickness. Released fractions measured from graphite and uranium carbide pellets are presented as well as Monte-Carlo simulations of the Brownian motion.

Ballistic impact response of laminated hybrid materials made of 5086-H32 aluminum alloy, epoxy and Kevlar® fabrics impregnated with shear thickening fluid

The ballistic impact behavior of hybrid composite laminates synthesized for armor protection was investigated. The hybrid materials, which consist of layers of aluminum 5086-H32 alloy, Kevlar® 49 fibers impregnated with shear thickening fluid (STF) and epoxy resin were produced in different configurations using hand lay-up technique. The hybrid materials were impacted by projectiles (ammunitions of 150g power-point) fired from a rifle Remington 7600 caliber 270 Winchester to strike the target at an average impact velocity and impact energy of 871m/s and 3687J, respectively. The roles of the various components of the hybrid materials in resisting projectile penetration were evaluated in order to determine their effects on the overall ballistic performance of the hybrid laminates. The effects of hybrid material configuration on energy dissipation during ballistic impacts were investigated in order to determine a configuration with high performance for application as protective armor. The energy dissipation capability of the hybrid composite targets was compared with the initial impact energy of low caliber weapons (according to NATO standards) in order to determinate the protection level achieved by the developed hybrid laminates. Deformation analysis and penetration behavior of the targets were studied in different stages; the initial (on target front faces), intermediate (cross-section), and final stages (target rear layers). The influence of target thickness on the ballistic impact response of the laminates were analyzed. Differences in ballistic behavior were observed for samples containing Kevlar® impregnated with STF and those containing no STF. Finally, mechanisms of failure were investigated using scanning electron microscopic examination of the perforations.

Impact perforation of monolithic polyethylene plates: Projectile nose shape dependence

Ductile thermoplastics, for example Ultra High Molecular Weight Polyethylene (UHMWPE), are of interest for their impact energy absorbing capabilities. While the impact perforation mechanisms of metallic targets have been investigated in some detail, far less progress has been made towards understanding the impact resistance of ductile polymers. The aim of this investigation is to identify the relationship between the projectile tip geometry and impact energy absorption of semi-crystalline thermoplastics. The focus of the study is light-weight monolithic plates of extruded polymer impacted normally by rigid projectiles at velocities up to 100 ms−1. Three polymers will be considered: Low Density Polyethylene (LDPE), High Density Polyethylene (HDPE) and Ultra High Molecular Weight Polyethylene (UHMWPE). Polyethylene provides a convenient test material, as variations in microstructure provide a contrast in mechanical properties, without significant variations in density. Three distinct projectile nose shapes are considered: blunt, hemi-spherical and conical. For a conical tip, perforation occurs by ductile hole expansion. For this nose shape the high yield strength and strain rate sensitivity of HDPE offers an advantage over the other two polyethylenes. Perforation by blunt and hemi-spherical projectiles is more sensitive to deformation localisation. The high strain hardening of UHMWPE, which increases with strain rate, results in a significantly greater impact resistance than either HDPE or LDPE. The perforation mechanisms and energy absorption of these PE plates are contrasted with those of thin aluminium alloy targets that have the same total mass. UHMWPE outperforms these metallic targets for all three projectile nose shapes. Finally, the influence of target thickness on the impact perforation of LDPE is considered. All three nose shapes show a linear increase in perforation energy with target thickness.

Influence of target thickness on the generation of high-density ion bunches by ultrashort circularly polarized laser pulses

Ion acceleration by ultrashort circularly polarized laser pulse in a solid-density target is investigated using two-dimensional particle-in-cell simulation. The ions are accelerated and compressed by the continuously extending space-charge field created by the evacuation and compression of the target electrons by the laser light pressure. For a sufficiently thin target, the accelerated and compressed ions can reach and exit from the rear surface as a high-density high-energy ion bunch. The peak ion energy depends on the target thickness and reaches maximum when the compressed ion layer can just reach the rear target surface. The compressed ion layer exhibits lateral striation which can be suppressed by using a sharp-rising laser pulse.

Influence of target thickness on resonant elastic scattering of protons by 19F

The excitation function and cross-sections of the reaction 19F(p,p) 19F, for protons in the energy range 0.75–2.8 MeV, were measured with an accurate method not dependent on the absolute values of the number of incident protons (beam charge collection) and of the target thickness. Corrections for target thickness and beam energy dispersion effects were introduced and their importance are discussed.

L-subshell ionization of rare earth elements by carbon ion bombardment

Measurements of L-shell X-ray production cross sections and corresponding L-subshell ionization cross sections for selected rare earth elements (57<or=Z<or=68) have been performed for 12C and 13C ion impact with energies 0.4-2.8 MeV amu-1. The influence of target thickness and projectile charge state on L-subshell ionization is examined experimentally. The measured L-subshell ionization cross sections are compared with the predictions of the ECPSSR and SCA theories. Strong underestimation of the experimental data in the low energy range by both theories is caused by the second-order effects not accounted for in the theoretical description. An agreement of the data with the theoretical predictions is improved by using the 'united atom' limit for the effective binding energies.

A Study on Fracture Behavior in SiC by Projectile Impact. Influence of Thickness and Projectile Size on Impact Damage.

The influence of target thickness and projectile size on the projectile impact damage generated on SiC targets is investigated. The projectile impact generates several types of damage such as a ring crack, a crater or a cone crack. In the case of thick targets, the residual strength of the targets does not depend on target thickness. This is due to that damage is generated only near the impacted surface. On the other hand, in the case of thin targets, the residual strength drops drastically. This is due to the generation of "back surface cracks." In addition, the projectile size affects the residual strength and the cone crack size. However, the minimum impact velocity at which ring cracks are generated does not change with projectile size.

Impact flash and debris cloud expansion of high-pure metal foils

Results of 2 mm aluminum spheres perforating Al, Cu, Mo, Au, Sn, and Zn metal foils of a purity > 99.9 % with thicknesses between 0.1 mm and 2.0 mm, densities of up to 20 g/cm 3, melting temperatures of 500 – 3000 K and specific heats of fusion of 20 – 350 kJ/kg at impact velocities between v p = 4.5 km/s and v p = 9 km/s are presented. The influence of target thickness, target material properties and impact velocity on the perforation hole diameter, impact flash duration and expansion velocity, fragmentation and debris cloud formation at nearly constant areal density is demonstrated. The dependence of impact crater pattern at witness plates on target material density, thickness, impact velocity and areal density ratio between projectile and target material is discussed. For tin and lead evidence is given for the ability of digital scanning electron microscope analysis as an effective tool for indicating change of aggregation from solid into liquid and for the determination of relative projectile and target material quantities.

The influence of target thickness and backstop material on proton-produced neutron beams for radiotherapy.

Results are presented of measurements of skin sparing, penetration and total dose per unit of incident charge for various target thicknesses and filtrations for a neutron beam generated by 42 MeV protons on beryllium. These results are contrasted to predictions outlined in a previous paper. The differences from these predictions are attributed to the contribution of low-energy neutrons produced by the residual proton beam in the thick copper target backstop.