Indoor Radon Concentrations Research Articles

Assessment of annual effective doses from indoor radon and thoron in Doi Lo, Chiang Mai, Thailand.

This study aimed to determine the annual effective dose resulting from radon and thoron progeny inhalation. The levels of radon, thoron, and progeny were assessed in residences situated in the Doi Lo region of Chiang Mai, Thailand. Indoor radon and thoron concentrations were detected using passive discriminative detectors. Using a progeny deposition rate detector, this study evaluates radon and thoron progeny [equilibrium-equivalent radon concentration (EERC) for radon and equilibrium-equivalent thoron concentration (EETC) for thoron]. Data were collected from 44 dwellings between March and May 2020. The results found that indoor radon concentrations ranged from 17 to 118Bqm-3, while thoron concentrations ranged from 12 to 72Bqm-3. The radon progeny (EERC) ranged from 4 to 173Bqm-3, whereas thoron progeny (EETC) ranged from 1 to 15Bqm-3. The total annual effective dose received from radon and thoron progeny inhalation varied from 0.5 to 5mSv y-1.

Practical cut-off value for radon concentration in indoor air using an activated-charcoal radon collector.

The World Health Organization (WHO) recommends that countries adopt the reference level of 100Bqm-3 for indoor radon gas. Adopting the reference level requires a preliminary assessment of the indoor radon concentration. In the preliminary investigation, a cut-off value is useful, which is a value for selecting samples that can be reliably determined to be below the reference level (in this paper, the WHO reference level) using a straightforward method. If the true value was the WHO reference level, then the cut-off value of the PicoRad collector for selecting samples was determined as 80Bqm-3 through the analysis of the 95% prediction interval.

Radionuclides distribution in soils and radon level assessment in dwellings of Mungo and Nkam Divisions, Cameroon.

Radionuclide and radon levels have been investigated in soil samples and residential environments within the Mungo and Nkam Divisions of the Littoral Region. These analyses employed gamma spectrometry facilitated by a NaI (Tl) detector for soil samples, yielding average activity concentrations of 226Ra, 232Th, and 40K at 23.8, 72, and 105Bqkg-1, respectively. Various radiological parameters were calculated to evaluate radiological hazards. Additionally, the indoor radon concentrations were quantified utilizing the CR-39 solid-state nuclear track detector (Radtrack), revealing an average concentration of 25Bqm-3 and an associated inhalation dose of 0.66mSv y-1. Risk assessments for lung cancer attributable to indoor radon exposure incorporated models such as the Harley model. An observed moderate correlation between indoor radon levels and external 226Ra concentrations implies that radon intrusion indoors might be substantially influenced by the 226Ra present in the subjacent soil, considering the construction of residential structures directly upon these terrains.

Measuring the real radon exhalation from walls in buildings

Building materials may significantly contribute to indoor radon activity concentration. Measuring the radon exhalation rate directly on the existing building elements represents the most accurate and reliable method to assess the building materials’ contribution. However, due to the method’s inner difficulties, no specific apparatus has been developed and documented in the literature.An innovative apparatus has been designed, constructed, and commissioned to measure the radon exhalation rate in situ from vertical surfaces of existing building walls. The apparatus is non-destructive, completely self-standing, and easily transportable. The sealing mechanism has been demonstrated to assure airtightness similarly to destructive setups. The measurements’ repeatability is less than 10% at different radon exhalation rates.The apparatus introduced is the only available solution to measure the site-dependent contribution of building materials to the indoor radon concentration. The apparatus allows for improving the specificity, so the effectiveness, of the remedial interventions to reduce the radon-related health risk.

Radiological characterization of materials used in the Italian heritage buildings

Building materials (BMs) can cause significant gamma dose indoors due to their natural radionuclide content. In 2013, the European Directive 59/2013/EURATOM introduced, in annex XIII, a list of types of BMs of interest for the content of gamma-emitting radionuclides among which materials or additives of natural igneous origin, such as granitoids, tuff and lava, are included. These materials have been largely employed for decorative and structural purposes in the course of centuries in the Italian heritage buildings. Aim of this study is to assess the contribute of BMs in terms of alpha exposure. Six samples of different materials, characterized in a previous study by the authors in terms of radiological content by means of a gamma spectrometry, have been analyzed in order to determine the specific exhalation rate of 222Rn, the radon emanation coefficient and excess in indoor radon concentration. Results confirm that BMs of natural igneous origin can play an important role in terms of alpha radiation dose and internal exposure due to the inhalation of the alpha particles emitted.

Coherent long-term average indoor radon concentration estimates obtained by electronic and solid state nuclear track detectors

Despite the rapid development of consumer-grade electronic radon monitors, their capabilities to assess long-term average radon concentrations are not systematically investigated. We present the results of a year-long measurement campaign in 32 dwellings and workplaces in two areas with typical and high radon concentrations in Bulgaria. A systematic comparison was made between electronic monitors and the gold standard — solid-state nuclear track detectors (SSNTDs). RadonEye Plus2 (RE) monitors were used, calibrated and metrologically tested at the three participating laboratories. Two SSNTD-based detectors were utilized: passive radon detectors (PRDs) developed by UKHSA, and CDs/DVDs, developed at SU. Two PRDs for quarterly radon measurements, a RE, a CD and a DVD were placed at each location. Additional old CDs/DVDs were collected for retrospective radon estimates. The results for the annual average radon concentrations, estimated by the four methods are presented. The average difference between the REs and PRDs estimate was 8% (median 4%), between the REs and CDs was 5% (median 0.4%) and between REs and DVDs was −10% (median −12%). The Z-score, representing the difference normalized to its uncertainty, in most cases fell within −1 and 1, indicating excellent agreement. The retrospective estimates also demonstrated excellent agreement with the other data. However, in some cases, small but statistically significant biases were identified between REs and SSNTDs or between different SSNTDs, requiring an inclusion of a reference instrument in future studies. Overall, the results imply that with sound metrological assurance, RadonEye Plus2 monitors can assess long-term average radon concentrations with sufficient accuracy.

Characteristic parameters and radon exhalation rates of aerated concrete blocks

ObjectiveTo understand the characteristic parameters and radon exhalation rates of aerated concrete blocks. MethodsA total of 39 nationally inspected samples were measured. Their dry density was determined based on their mass and volumes, their porosities were measured on the principle of volumetric expansion, and their radium content was determined using a high-purity germanium (HPGe) detector for gamma-ray spectroscopy. Furthermore, their diffusion lengths were quantified by establishing a combined cumulative and diffusion chamber, and their radon exhalation rates were measured through closed-box testing using a continuous radon monitor. ResultsThe aerated concrete blocks exhibited dry densities ranging from 464 to 840 ​kg/m3 [average: (654.0 ​± ​82.5) kg/m3], open porosities from 67.1 ​% to 81.1 % [average: (74.3 ​± ​3.3) %, radium (226Ra) content from 12.3 to 136 Bq/kg [average: (63.0 ​± ​30.4) Bq/kg], diffusion lengths from 0.49 to 1.01 ​m [average: (0.70 ​± ​0.15) m], and radon exhalation rates from 0.6 to 22.8 Bq·m−2·h−1 [average: (7.3 ​± ​5.3) Bq·m−2·h−1]. ConclusionAerated concrete blocks exhibit significantly higher porosities, diffusion lengths, and radon exhalation rates than traditional concrete and clay bricks. These blocks might contribute to the high indoor radon concentration observed in modern buildings in China.

Influence of Meteorological Parameters on Indoor Radon Concentration Levels in the Aksu School

The radon concentration activity in buildings is influenced by various factors, including meteorological elements like temperature, pressure, and precipitation, which are recognized as significant influencers. The fluctuations of indoor radon in premises are related to seasonal change. This study aimed to understand better the effects of environmental parameters on indoor radon concentration levels in the Aksu school. Indoor and outdoor temperature differentials heavily influence diurnal indoor radon patterns. The analysis indicates that the correlation between indoor radon and outdoor temperature, dew point, and air humidity is weak and negligible for atmospheric pressure, wind speed, and precipitation, as determined by the obtained values of R2 and the Chaddock scale. The multiple regression model is characterized by the correlation coefficient rxy = 0.605, which corresponds to a close relationship on the Chaddock scale.

Development of a High-Resolution Indoor Radon Map Using a New Machine Learning-Based Probabilistic Model and German Radon Survey Data.

Radon is a carcinogenic, radioactive gas that can accumulate indoors and is undetected by human senses. Therefore, accurate knowledge of indoor radon concentration is crucial for assessing radon-related health effects or identifying radon-prone areas. Indoor radon concentration at the national scale is usually estimated on the basis of extensive measurement campaigns. However, characteristics of the sampled households often differ from the characteristics of the target population owing to the large number of relevant factors that control the indoor radon concentration, such as the availability of geogenic radon or floor level. Furthermore, the sample size usually does not allow estimation with high spatial resolution. We propose a model-based approach that allows a more realistic estimation of indoor radon distribution with a higher spatial resolution than a purely data-based approach. A multistage modeling approach was used by applying a quantile regression forest that uses environmental and building data as predictors to estimate the probability distribution function of indoor radon for each floor level of each residential building in Germany. Based on the estimated probability distribution function, a probabilistic Monte Carlo sampling technique was applied, enabling the combination and population weighting of floor-level predictions. In this way, the uncertainty of the individual predictions is effectively propagated into the estimate of variability at the aggregated level. The results show an approximate lognormal distribution of indoor radon in dwellings in Germany with an arithmetic mean of , a geometric mean of , and a 95th percentile of . The exceedance probabilities for 100 and are 12.5% (10.5 million people affected) and 2.2% (1.9 million people affected), respectively. In large cities, individual indoor radon concentration is generally estimated to be lower than in rural areas, which is due to the different distribution of the population on floor levels. The advantages of our approach are that is yields a) an accurate estimation of indoor radon concentration even if the survey is not fully representative with respect to floor level and radon concentration in soil, and b) an estimate of the indoor radon distribution with a much higher spatial resolution than basic descriptive statistics. https://doi.org/10.1289/EHP14171.

Evaluating radon concentration and temporal correction factors in residential and workplace buildings: A comparison of passive and active methods

Effective mitigation of the health impacts of radon exposure begins with accurate measurement of this environmental contaminant. Typically, radon surveys require measurements over a period of several months. This process involves the application of temporal correction factors (TCF). Disparities in indoor radon concentration (IRC) are evident across building types. While the integrated technique has traditionally been considered the most reliable for measuring IRC, the active method is becoming more prevalent due to the availability of commercial radon measurement instruments. The aim of this study is to compare IRC using passive (CR-39) and active (ICA device) methods across 69 indoor spaces, including 35 workplaces and 34 residential buildings. The investigation was conducted over a span of one year and included 966 CR-39 detectors that were replaced every 3 and 6 months, respectively, to assess seasonal fluctuations and facilitate the computation of TCF. Statistically significant differences in IRC were observed between residential and workplace buildings (p < 0.001). Among workplaces, educational and research institutions showed the highest average IRC (166 Bq/m3), while hospitals exhibited the lowest (25 Bq/m3). Significant differences in TCF were found between the two measurement methods (p < 0.05), making TCF specific to the passive method inapplicable to active method. Moreover, distinctions between workplace and residential buildings, including the presence of air conditioning units and differing occupancy patterns, lead to substantial differences in both IRC (p < 0.001) and TCF. The assessment of radon exposure based on room occupancy duration revealed substantial variations: workplaces showed lower actual exposure (62 Bq/m3 vs. 75 Bq/m3, p < 0.001), while residential settings, particularly at night, displayed higher exposure (278 Bq/m3 vs. 245 Bq/m3, p = 0.02) than integrated measurements suggest. Continuous monitoring systems offer critical insights into true radon exposure levels.

The correlation between indoor and soil gas radon concentrations in Kiraz district, İzmir.

All humans are exposed to radon, the primary source of natural radiation, which can harm people due to natural processes rather than human activity. Thus, it is of significant importance to determine the levels of radon in indoor, soil gas, water, and outdoors. Radon concentration (CRn) was measured in Kiraz district, İzmir, and the correlation between the indoor and soil gas CRn values was investigated. The indoor CRn values measured in 40 randomly selected dwellings in Kiraz exhibited a wide range from 19.50 ± 2.50 to 204.70 ± 8.00Bqm-3 with an average value of 61.11 ± 4.23Bqm-3. The measured indoor CRn values were compared to the reference levels in the world to help control radon in the dwellings. Indoor CRn values were lower than the ICRP reference level of 300Bqm-3 in all of the dwellings studied. Furthermore, in 34 dwellings (representing 85% of the total number of dwellings studied), indoor CRn values were lower than the WHO reference level of 100Bqm-3. Health hazard indices, namely annual effective dose (AED) and excess lifetime cancer risk (ELCR), were also calculated for each dwelling and compared with internationally acceptable levels to estimate the risk to human health. The AED values varied from 0.49 ± 0.06 to 5.16 ± 0.20mSv y-1 with an average value of 1.54 ± 0.11mSv y-1, which exceeds the world average of 1.15mSv y-1 as reported by UNSCEAR. The ELCR values ranged from 2.05 ± 0.26 × 10-3 to 21.55 ± 0.84 × 10-3 with an average value of 6.43 ± 0.44 × 10-3, exceeding the world average of 0.29 × 10-3 as reported by UNSCEAR. The soil gas CRn values measured exhibited a wide variation ranging from 129.25 ± 6.38Bqm-3 to 6172.64 ± 44.06Bqm-3 with an average value of 1291.79 ± 18.70Bqm-3. The soil gas CRn values were less than 10,000Bqm-3; hence, the research area is categorized as "low radon risk areas" according to Sweden Criteria, and so no special constructions are required in the studied area. When soil gas CRn values were compared to indoor CRn values, no linear relationship was found between the CRn values. However, a strong positive linear correlation was found between indoor and soil gas CRn values less than 200Bqm-3 and 2500Bqm-3, respectively.

Assessing the Radon Exposure Variability and Lifetime Health Effects across Indoor Microenvironments and Sub-Populations

To assess the health impacts of radon exposure over a lifetime, in the present study, the annual effective dose (AED) and cumulative excess lifetime cancer risk (ELCR-C) were evaluated by considering various indoor microenvironmental exposures based on age-specific time–activity patterns using Monte Carlo simulations. Significant regional variations in indoor radon concentrations across the Republic of Korea were observed, with the highest levels found in schools and single detached houses. Based on the standard annual total of 8760 h spent indoors and outdoors, the AED varied by age group and dwelling type, with the ELCR-C for single detached houses being approximately 1.36 times higher than that for apartments on average. The present study highlights the importance of comprehensive health risk assessments that consider differences across indoor environments and age groups, indicating that limited evaluations of specific sites or areas may distort actual exposure levels.

Effective dose assessment due to inhalation of 222Rn, 220Rn, and their progeny: highlighting the major contribution of thoron in a thoron-prone area in Cameroon.

To assess public exposure to radon, thoron, and their progeny, measurements were conducted in 50 dwellings within the bauxite-rich area of Fongo-Tongo in western Cameroon. Passive integrating radon-thoron discriminative detectors (specifically RADUET) were employed for radon and thoron measurements. Additionally, concentrations of short-lived radon and thoron progeny were estimated using Direct Radon Progeny Sensors (DRPSs) and Direct Thoron Progeny Sensors (DTPSs) based on LR-115 detectors. The findings revealed indoor radon concentrations ranging from 31 to 123Bqm-3 with a geometric mean (GM) of 62Bqm-3, and indoor thoron concentrations ranging from 36 to 688Bqm-3 with a GM of 242Bqm-3. The Equilibrium Equivalent Radon Concentration (EERC) ranged from 3 to 86Bqm-3 with a GM of 25Bqm-3, while the Equilibrium Equivalent Thoron Concentration (EETC) ranged from 1.2 to 12.5Bqm-3 with a GM of 7.6Bqm-3. Notably, all dwellings recorded radon concentrations below 100Bqm-3. Arithmetic means of radon and thoron equilibrium factors were calculated as 0.47 and 0.04, respectively. To assess annual effective doses from radon and thoron inhalation, equilibrium factors were used along with direct measurements of EERC and EETC. The differences observed in annual effective doses were 4.5% for radon and 42.5% for thoron. Furthermore, the contribution of thoron and its decay products to the annual effective dose from radon, thoron, and their progeny ranged from 12 to 94%, with an average contribution of 58%. Thus, this study found that the effective dose due to thoron inhalation in the study area exceeded that due to radon inhalation. It is concluded that, when evaluating radiation doses and health risks, it is crucial to consider both thoron and its progeny alongside radon and its progeny. This underscores the importance of considering direct measurements for accurately estimating radiation doses.

Indoor Radon Concentrations in Severe Cold Area and Cold Area and Impact of Energy-saving Design on Indoor Radon in China.

This study investigated indoor radon concentrations in modern residential buildings in the Cold Area and Severe Cold Area in China. A total of 19 cities covering 16 provinces were selected with 1,610 dwellings measured for indoor radon concentration. The arithmetic mean and geometric mean of indoor radon concentration were 68 Bq m-3 and 57 Bq m-3, respectively. It was found that indoor radon concentrations were much higher in the Severe Cold Area than those in the Cold Area. The indoor radon concentrations showed an increasing trend for newly constructed buildings. It was estimated that the average effective dose from inhalation of indoor radon is 2.15 mSv and 1.60 mSv for the Severe Cold Area and Cold Area, respectively. The more and more rigid energy-saving design for residential buildings in the Severe Cold Area and Cold Area has an obvious impact on the increased trend of indoor radon due to extremely low air exchange rate in China.

Analysis of radon mitigation methods: 10-year review

Exposure to the radon gas within a building can result in an increased risk of lung cancer. To minimise the health risk, indoor radon concentrations can be reduced using well-established mitigation methods. The performance of various radon reduction methods, their combination as well as other factors that can impact the efficiency of radon mitigation, were analysed using data collected from approximately 2800 dwellings that had installed radon mitigation techniques during the period 2007–2017. As demonstrated previously (Hodgson 2011), active methods are the most effective at reducing high concentrations of radon to below the Action and Target Levels (200 Bq m−3 and 100 Bq m−3 respectively). Reduction factors of up to 5.5 using single active methods and 8.3 using a combination of active methods were estimated in this study. For indoor radon levels greater than 1 000 Bq m−3, the Active Sump remained the most efficient technique, with the Active Underfloor Ventilation being the second most effective method. Passive methods alone or in combination with other passive methods offered moderate reductions at high radon concentration. Of the passive methods, Underfloor Ventilation was found to have the highest performance with a reduction factor of 1.8. The conclusions of this study should be used to update guidance for stakeholders including householders, contractors, radon awareness campaigns and the UKradon.org website.

Assessment of radon levels in indoor workplaces in Tunisia and associated radiological risks

ABSTRACT This study aimed to assess indoor radon levels within different workplaces in Tunisia, including universities, schools, spa centres, and phosphate fertiliser factories. A total of 110 locations within these workplaces were monitored using solid-state nuclear track detectors (LR 115). The obtained results indicated that the geometric mean (GM) values of indoor radon concentrations measured at these locations were 24.6 Bq m−3 for universities, 31.3 Bq m−3 for schools, 72.2 Bq m−3 for spa centres, and 70.0 Bq m−3 for phosphate fertiliser factories. Overall, the GM of indoor radon concentrations measured in the four studied workplaces remained below standard values. Statistical analysis using the two-sample Student t-test revealed significant differences between the workplaces. The calculated annual effective doses due to radon inhalation were found to have GM values of 0.2 mSv y−1 for universities, 0.2 mSv y−1 for schools, 0.5 mSv y−1 for spa centres, and 0.4 mSv y−1 for phosphate fertiliser factories. These values are comparable to worldwide average values. Other risk parameters, such as lung cancer risk and lung cancer cases were also determined and reported in this study. While this study did not investigate the factors influencing radon concentrations, its primary advantage lies in being the first comparative study monitoring various workplaces in Tunisia, covering both underground and above-ground settings.

Unintended Consequences of Urban Expansion and Gold Mining: Elevated Indoor Radon Levels in Gauteng Communities’ Neighboring Gold Mine Tailings

The province of Gauteng in South Africa has a rich history of gold mining, which has driven economic growth and urbanization. Gold mining has also created over 270 gold mine tailings (GMT), now surrounded by human settlements due to a housing shortage. These GMT pose a health risk as they harbor elevated uranium, which over time undergoes radioactive decay to produce radon, a known lung carcinogen. This study aimed to investigate the potential correlation between the proximity to gold mine tailings (GMT) and indoor radon concentrations in Gauteng’s residential dwellings. Volume activity of radon (VAR) inside 330 residential dwellings was measured in residential dwellings located proximally (&lt;2 km) and distally (&gt;2 km) to gold mine tailings using AlphaE radon monitors during winter. An interviewer-administered questionnaire was utilized to obtain data on factors that may influence indoor radon activities. Descriptive statistics and bivariate logistic regression analyzed the influence of proximity to gold mine tailings and dwelling characteristics on VAR. Furthermore, VAR was compared to the World Health Organization (WHO) radon reference level of 100 Bq/m3. Residential dwellings near gold mine tailings had significantly higher average indoor radon concentrations (103.30 Bq/m3) compared to the control group (65.19 Bq/m3). Residential dwellings proximal to gold mine tailings were three times more likely to have VAR beyond the WHO reference level of 100 Bq/m3. Furthermore, they had estimated annual effective doses of 2.60 mSv/y compared to 1.64 mSv/y for the control group. This study highlighted a concerning association between proximity to gold mine tailings and elevated indoor radon levels. Public health interventions prioritizing residential dwellings near gold mine tailings are crucial. Educational campaigns and financial assistance for radon mitigation systems in high-risk dwellings are recommended. Residents near gold mine tailings are encouraged to ensure continuous natural ventilation through frequent opening of windows and doors.

Strategy and Metrological Support for Indoor Radon Measurements Using Popular Low-Cost Active Monitors with High and Low Sensitivity.

Traditionally, for indoor radon testing, predominantly passive measurements have been used, typically applying the solid-state alpha track-etch method for long-term and the charcoal method for short-term measurements. However, increasingly, affordable consumer-grade active monitors have become available in the last few years, which can generate a concentration time series of an almost arbitrary duration. Firstly, we argue that consumer-grade monitors can well be used for quality-assured indoor radon assessment and consequent reliable decisions. Secondly, we discuss the requirements of quality assurance, which actually allow for reliable decision-making. In particular, as part of a rational strategy, we discuss how to interpret measurement results from low-cost active monitors with high and low sensitivity with respect to deciding on conformity with reference levels that are the annual average concentration of indoor radon. Rigorous analysis shows that temporal variations in radon are a major component of the uncertainty in decision-making, the reliability of which is practically independent of monitor sensitivity. Manufacturers of low-cost radon monitors already provide sufficient reliability and quality of calibration for their devices, which can be used by both professional inspectors and the general public. Therefore, within the suggested measurement strategy and metrologically assured criteria, we only propose to clarify the set and values of the key metrological characteristics of radon monitors as well as to upgrade user-friendly online tools. By implementing clear metrological requirements as well as the rational measurement strategy for the reliable conformity assessment of a room (building) with radon safety requirements, we anticipate significant reductions in testing costs, increased accessibility, and enhanced quality assurance and control (QA/QC) in indoor radon measurements.

Associations Between Gestational Residential Radon Exposure and Term Low Birthweight in Connecticut, USA.

Studies suggest biologic mechanisms for gestational exposure to radiation and impaired fetal development. We explored associations between gestational radon exposure and term low birthweight, for which evidence is limited. We examined data for 68,159 singleton full-term births in Connecticut, United States, 2016-2018. Using a radon spatiotemporal model, we estimated ZIP code-level basement and ground-level exposures during pregnancy and trimesters for each participant's address at birth or delivery. We used logistic regression models, including confounders, to estimate odds ratios (ORs) for term low birth weight in four exposure quartiles (Q1-Q4) with the lowest exposure group (Q1) as the reference. Exposure levels to basement radon throughout pregnancy (0.27-3.02 pCi/L) were below the guideline level set by the US Environmental Protection Agency (4 pCi/L). The ORs for term low birth weight in the second-highest (Q3; 1.01-1.33 pCi/L) exposure group compared with the reference (<0.79 pCi/L) group for basement radon during the first trimester was 1.22 (95% confidence interval [CI] = 1.02, 1.45). The OR in the highest (Q4; 1.34-4.43 pCi/L) quartile group compared with the reference group during the first trimester was 1.26 (95% CI = 1.05, 1.50). Risks from basement radon were higher for participants with lower income, lower maternal education levels, or living in urban regions. This study found increased term low birth weight risks for increases in basement radon. Results have implications for infants' health for exposure to radon at levels below the current national guideline for indoor radon concentrations and building remediations.

Assessment of indoor radon concentration in the dwellings of the industrial areas of Kannur District, Kerala.

All organisms on the earth-crest are exposed to natural background radiation since the evolution of the earth, as many environmental matrices such as soil, air, water bodies, vegetation, etc., act as the sources of natural radioactivity. The present study deals with the evaluation of indoor concentration of 222Rn (radon) in different dwellings with various construction materials used for the roof and floor in the industrial sites of Kannur district, Kerala. A pinhole-based dosemeter coupled with LR-115 Solid State Nuclear Track Detector and Direct Radon Progeny Sensor (DRPS) were respectively used for the measurement of indoor radon concentration and equilibrium equivalent concentration of radon. The indoor radon concentrations were found to vary from 102.30 Bqm-3 to 184.75 Bqm-3 and the values were within the recommended limits provided by International Commission on Radiological Protection (ICRP). The annual effective doses and excess lifetime cancer risks were observed in the range of 2.58-4.66 mSvy-1 and 7.68×10-3-15.60×10-3, respectively, and both exceed the world average values recommended by United Nations Scientific Committee on the Effects of Atomic Radiation (UNSCEAR) 2000. The study shows that, the houses with marble floors and concrete roofs have comparatively higher values of radon concentration, which indicates the significant contribution of construction materials to the enhanced radiation levels inside the dwellings.