Increase In Content Research Articles

Effect of limestone powder on mechanical properties of concrete based on Griffith’s microcracking theory

In order to reveal the influence mechanism of limestone powder on the mechanical properties of concrete, the manufactured sand concrete with a water-cement ratio of 0.45 was taken as the research object. The effects of different limestone powder contents (0%, 5%, 10%, 15%, and 20%) on the compressive strength of concrete were explored based on Griffith’s microcracking theory. The nano-indentation, ultra-depth-of-field microscopy, LF-NMR, and other methods were used for testing. The test results show that with the increase of limestone powder content, the elastic modulus of the Interfacial Transition Zone (ITZ) and the paste increases first and then decreases, the thickness of the ITZ decreases first and then increases, and the total porosity of the paste decreases first and then increases. The microstructure of the ITZ and the paste is the densest, corresponding to the maximum compressive strength of the concrete as the limestone content is 10%. It is found that the thickness of ITZ can be regarded as the initial crack of concrete. The compressive strength of concrete calculated by Griffith’s microcracking theory formula is the same as the measured value. The research results provide a theoretical reference for the influence mechanism of limestone powder on the mechanical properties of concrete.

Distribution of lipid droplets in hippocampal neurons and microglia: impact of diabetes and exercise.

Neuroinflammation, aging, and neurodegenerative disorders are associated with excessive accumulation of neutral lipids in lipid droplets (LDs) in microglia. Type 2 diabetes mellitus (T2DM) may cause neuroinflammation and is a risk factor for neurodegenerative disorders. Here, we show that hippocampal pyramidal neurons contain smaller, more abundant LDs than their neighboring microglia. The density of LDs varied between pyramidal cells in adjacent subregions, with CA3 neurons containing more LDs than CA1 neurons. Within the CA3 region, a gradual increase in the LD content along the pyramidal layer from the hilus toward CA2 was observed. Interestingly, the high neuronal LD content correlated with less ramified microglial morphotypes. Using the db/db model of T2DM, we demonstrated that diabetes increased the number of LDs per microglial cell without affecting the neuronal LD density. High-intensity interval exercise induced smaller changes in the number of LDs in microglia but was not sufficient to counteract the diabetes-induced changes in LD accumulation. The changes observed in response to T2DM may contribute to the cerebral effects of T2DM and provide a mechanistic link between T2DM and neurodegenerative disorders.

Inhibitory Effect of Tanshinone IIA Extracted from Radix Salviae miltiorrhizae on Melanoma B16F10 Cells

In this study, we investigate the inhibitory effects of Tanshinone IIA on the proliferation and migration of B16F10 melanoma cells and its potential mechanism of action. We cultured B16F10 melanoma cells in vitro and treated them with varying concentrations of tanshinone IIA. The inhibitory effect of tanshinone IIA on B16F10 cells was assessed using the CCK-8 assay, employing methyl thiazolyl tetrazolium. Melanin content was determined by the NaOH cleavage method, while expression levels of melanin-related proteins were analyzed by Western blotting, and migration-related proteins were quantified using ELISA. When the concentration of Tanshinone IIA reached 20 and 40 μg/mL, there was a decrease in the survival rate of B16F10 melanoma cells. The proliferation inhibition rate of B16F10 melanoma cells gradually increased with the duration of drug action and the concentration of Tanshinone IIA. After 48 hours, there was an increase in melanin content. A comparison of melanin synthesis at the three concentrations yielded an F value of 61.820 and P <0.001. The relative expression levels of TYR, TRP-1, TRP-2, and MITF increased when treated with different concentrations of Tanshinone IIA (P < 0.05). MMP-2 and MMP-9 were downregulated when the concentration of Tanshinone IIA was at 40 and 80 μg/mL respectively (P <0.05). In conclusion, our study demonstrated the inhibitory effects of Tanshinone IIA on growth, proliferation, migration, and melanin synthesis in B16F10 melanoma cells. However, further research is needed to elucidate the specific signal transduction pathway activated by Tanshinone IIA.

The influence of carbon content gradient and carbide precipitation on the microstructure evolution during carburizing-quenching-tempering of 20MnCr5 bevel gear

Due to the mechanism of microstructural transition, high-strength low-carbon alloy steel gears exhibit high strength and surface hardness after Carburizing-Quenching-Tempering (CQT) combined heat treatment, while maintaining good toughness in the core. The carbon potential gradient and the precipitation of carbides are the main factors affecting the final microstructure, yet there is a shortage of related research. To address this gap, this study developed a multi-physics coupled model considering the impact of carbon content to simulate microstructural transformation. Using finite element analysis, we simulated the microstructural evolution during the CQT heat treatment of 20MnCr5 bevel gear. By comparing the simulation results with the calculations from the commercial heat treatment software DANTE®, the accuracy of this model in predicting microstructural distribution and hardness has been validated. Furthermore, the study established a carbide precipitation kinetics model that takes into account the influence of grain size, to investigate the precipitation behavior of carbides within the matrix during the tempering stage. The cellular automaton method was applied to demonstrate the evolution process of the quenched microstructure during tempering. The study shows that during tempering, carbides primarily precipitate in areas with higher carbon content, preferentially at the boundaries of fine grains with a high density of lattice defects. As the carbon content increases, the number density of precipitates rises, while their average radius decreases. The reduction in matrix supersaturation due to carbide precipitation is one of the causes for the reduction of tooth surface hardness during tempering. The model constructed in this study provides a new perspective for understanding the laws governing material microstructural evolution and offers a solid theoretical foundation for the study of stress and deformation during the heat treatment process.

Plastic deformation mechanism of γ phase Fe–Cr alloy revealed by molecular dynamics simulations

Abstract Due to their outstanding mechanical properties, anti-corrosion properties, and anti-irradiation swelling properties, Fe–Cr alloys have been fully improved and developed for nuclear energy applications as structural materials. To ensure the performance stability of γ-phase Fe–Cr alloys, the present study adopted molecular dynamics (MD) simulations to explore the plastic deformation mechanism of these alloys. The slip model was constructed, and the generalised stacking fault energy (GSFE) and Peierls–Nabarro (P–N) equations were solved, revealing that {110}<111> is the preferentially activated slip system. The twinning model was constructed and the generalised plane fault energy was solved, demonstrating that twinning is preferred over slipping in the {112}<111> system. The above findings are also verified through MD simulations in which Fe–Cr specimens are stretched along the [100] direction. In addition, in the 15 at.%–25 at.% Cr range, an increase in the Cr content has a negative effect on slip but a positive effect on twin formation.

Effect of Superfilling and Leveling Inhibitors in Hybrid Additives on the Microstructure Evolution of Electroplated Copper Interconnect Films during Self-Annealing

Abstract As the feature size shrinks, the main challenge for copper interconnect electroplating is to minimize interconnect resistance while ensuring the void-free feature filling, which is realized by the interaction of additives during electroplating. Among additives, hybrids are considered suitable for damascene filling because they combine type-I (superfilling) and type-II (leveling) inhibitors. However, it is generally believed that the more inhibitory an additive is, the more impurities it introduces into the films, thereby hindering grain growth during self-annealing, which paradoxically limits the conductivity of copper interconnects. To balance the inhibition of hybrid additives with their ability to introduce impurities, the effect of hybrid additives on the microstructure evolution of the films during self-annealing is explored in terms of texture, grain size, and impurity density, which are considered to determine the conductivity of copper films. We find that the {111} texture increases as the percentage of type-I inhibitors increases, whose relative texture coefficient reaches 97% after self-annealing due to the adsorption of hybrid additives on non-<111>-oriented crystal planes. Additionally, the impurity content and grain size increase as type-I inhibition increases, and so does the film conductivity after self-annealing, due to the possible promotion from impurities to the grain growth.

Investigation of the Time-Dependent Deformation of Recycled Aggregate Concrete in a Water Environment

The water environment greatly affects the creep deformation of recycled aggregate concrete (RAC). Hence, a humidity–stress–damage coupling numerical model was used for investigating the time-dependent deformation of RAC in the water environment in this study. Firstly, uniaxial compression and water absorption tests were performed to determine the calculation parameters of the creep numerical simulation of RAC in a water environment. Experimental results indicate that the elastic modulus and compressive strength drop as the water content increases. Then, the time-dependent deformation of RAC in a water environment was studied using a numerical simulation test of compressive creep when multiple stress levels were applied, and the critical stress for accelerated creep and the long-term strength of RAC were obtained. Finally, the influence of confining pressures on the long-term deformation of RAC in a water environment was discussed. When there is no confining pressure, the long-term strength of RAC is 23.53 MPa. However, when a confining pressure of 3.921 MPa is loaded onto RAC, the long-term strength of RAC is 47.052 MPa, which increases by 100%. Increasing confining pressures has an obvious effect on ensuring the long-term stable application of RAC in a water environment. Compared with the creep test, the method adopted in this study saves time and money and provides the theoretical basis for evaluating the time-dependent deformation of RAC in a water environment.

Influence of Foam Content and Concentration on the Physical and Mechanical Properties of Foam Concrete

Foam concrete has been used in various real-life applications for decades. Simple manufacturing methods, lightweight, high flowability, easy transportability, and low cost make it a useful construction material. This study aims to develop foam concrete mixtures for various civil and geotechnical engineering applications, such as in-fill, wall backfill and soil replacement work. A blended binder mix containing cement, fly ash and silica fume was produced for this study. Its compressive strength performance was compared against conventional general purpose (GP) cement-based foam concrete. Polypropylene (PP) fibre was used for both mixtures and the effect of various percentages of foam content on the compressive strength was thoroughly investigated. Additionally, two types of foaming agents were used to examine their impact on density, strength and setting time. One foaming agent was conventional, whereas the second foaming agent type can be used to manufacture permeable foam concrete. Results indicate that an increase in foam content significantly decreases the strength; however, this reduction is higher in GP mixes than in blended mixes. Nevertheless, the GP mixes attained two times higher compressive strength than the blended mix’s compressive strengths at any foam content. It was also found that the foaming agent associated with creating permeable foam concrete lost its strength (reduced by more than half), even though the density is comparable. The compressive stress–deformation behaviour showed that densification occurs in foam concrete due to its low density, and fibres contributed significantly to crack bridging. These two effects resulted in a long plateau in the compressive stress–strain behaviour of the fibre-reinforced foam concrete.

Effect of graphene on microstructure, strain hardening and corrosion behaviour of dual phase Mg-Li matrix processed through liquid metallurgy route

The significance of this study lies in the potential enhancement of magnesium (Mg)-based materials through the addition of graphene, aiming to improve their mechanical properties and corrosion resistance. This research investigates the development of graphene-Mg composites, employing a liquid metallurgy route to fabricate a dual-phase structured Mg-8Li composite. Mg-Li dual-phase composites are of interest due to their lightweight nature and promising mechanical properties, making them suitable for applications in aerospace, automotive, and structural engineering. Graphene was incorporated into the Mg matrix at varying percentages (0.2, 0.4 and 0.6 wt.%), and the resulting materials were subjected to microstructural, mechanical, and corrosion analyses. Microstructural characterization results reveals that the increase in graphene content results in decrement in grain size of α-Mg and β-Li up to ∼33 and ∼11.5% respectively. Likewise, additions of graphene improvise tensile and yield strength of base matrix up to ∼47 and ∼44% respectively. Strain hardening exponent (n) values of base material decrease from 0.21 to 0.17 with respect to graphene addition which confirms the effect of graphene that acts as effective barrier to slip that decreases the deformation. Corrosion analysis revealed a decrease in corrosion rate and increased pitting resistance with the addition of graphene, indicating improved corrosion resistance. Electrochemical impedance spectroscopy results depict that the composite with 0.4 wt.% graphene exhibits larger semi conducting loop with higher charge transfer resistance ( Rct) value of 128 Ω cm2.

ASSESSMENT OF THE INFLUENCE OF INORGANIC PIGMENTS ON THE TECHNOLOGICAL PROPERTIES OF DECORATIVE CEMENTS

The article presents the results of research on the influence of inorganic pigments on the technological properties of decorative cements. It has been established that regardless of the color of the pigment, with an increase in its quantity in the system, we get a more saturated and bright color of cement stone, but at the same time there is a negative effect of pigments and technological and physical and mechanical properties of artificial stone. The research was conducted on cement systems based on white Portland cement without additives and on cement systems based on white Portland cement modified with polycarboxylate superplasticizer. An increase in the amount of pigment, regardless of its color, leads to an increase in the water consumption of the cement system, however, when a superplasticizer is introduced, the effect of the pigment is not so significant. At the same time, the introduction of a superplasticizer reduces the water consumption of white cement without the introduction of pigments by an average of 37-40%. In addition, it was established that the introduction of pigments affects the hardening time of cement systems. At the same time, pigments, depending on their color and dosage, have different effects on both the start and end of aging. With an increase in the pigment content in a cement system without a plasticizer, the time of the onset of hardening increases, and the introduction of a permanent pigment has the greatest effect on the end of hardening of such a system. The introduction of pigments into plasticized cement systems increases both the start and end time of hardening. As the number of pigments of all colors increases, the strength of the samples decreases. At the same time, the red pigment leads to the greatest decline in strength at all stages of hardening. The decrease in strength can be explained by the increased water consumption, and, as a result, the increased porosity of pigmented samples compared to samples without the introduction of pigments. Further research aimed at finding additives that will reduce the negative impact of inorganic pigments on the processes of hydration and hardening of the cement system, and therefore on the durability of the obtained artificial stone, will be relevant. At the same time, it is important to preserve the intensity of the color and the absence of sediment formation.

Epitaxial crystallization of polylactic acid on layered zinc phenylphosphonate: Mutual perpendicular rodlike crystals under two lattice matchings

AbstractAs a highly effective nucleating agent, layered zinc phenylphosphonate (PPZn) is incorporated into polylactic acid (PLA) to investigate the epitaxial crystallization of PLA on PPZn in this study. The corresponding lattice spacing change, crystalline morphology, and crystalline structure are emphasized to reveal the epitaxial crystallization mechanism. As a result, with the increase of PPZn content and the annealing time, the increasing lattice spacing of PPZn and the formation of mutually perpendicular rodlike crystals are observed through x‐ray diffraction (XRD) and polarized optical micrograph (POM) measurements, implying that the interlayer spacing of PPZn crystals is expanded as the PLA α‐form crystals epitaxially grow on its surface, that is, epitaxial crystallization. To be specific, “edge on” lamellae epitaxial grow on the PPZn crystals along the [010] and [100] directions under two excellent lattice matchings, which possess acceptable mismatching of 0.347% and 7.5%, respectively. With the support of the epitaxial crystallization mechanism, the occurrence of the filamentous structure observed in the fracture morphology of PLA/PPZn composites suggests strong interfacial adhesion between PLA and PPZn, which makes the impact toughness of the PLA/PPZn composites increase by 53.6% compared with pure PLA.

The Impact of Waste Application on the Reclamation and Biological Life of Degraded Soils

This work concerns the assessment of soil reclamation and its impact on biological life in areas destroyed by the sulfur industry in Jeziórko. Sulfur extraction using the borehole method causes enormous destruction to the soil environment. Among the many forms of degradation, the most pronounced are the chemical transformations of the environment and the disturbances in water relations in large areas, which could theoretically impact areas not within the direct range of the mining plant. This work aimed to assess the condition of biological life in soil reclaimed with waste in areas devastated by the sulfur industry in Jeziórko. The reclamation of these soils was difficult but necessary due to the complete disappearance of biological life. Appropriate actions were taken to restore and improve the properties of the soil, which resulted in an improvement in their production capacity. Reclamation was carried out, among other techniques, by deacidifying the soil using post-flotation lime and fertilizing the soil with municipal sewage sludge and post-use mineral wool. Studies have shown an improvement in many soil properties, such as its physical, water, chemical, and biological properties. The implemented reclamation methods significantly influenced, among other things, the density and water properties of the degraded soil. The soil reclaimed with mineral wool and sewage sludge recorded the highest density and water capacity. Applying mineral wool to the degraded soil influenced the changes in the analyzed physical and water properties. The obtained research results also show the beneficial effect of mineral wool and sewage sludge on the increase in organic carbon content. In the soil treated with these substances, the organic carbon content ranged from 13.60 g·kg−1 to 14.30 g·kg−1. It is shown that reclamation has had a considerable impact on and is essential for biological life in Jeziórko.

Effects of additives on compost quality and cbbL-containing autotrophic microbial community of watermelon straw composting

The amount of CO2 emission reflects the microbial activity in compost, but excessive emission can reduce humification degree of compost. Therefore, this study assessed the effects of superphosphate (SSP) and dicyandiamide (DCD) on CO2 emission, compost quality, and cbbL-containing autotrophic microbes (CCAM) community of watermelon straw composting. Results revealed that SSP and DCD promoted the compost maturity, but the DCD alone did not significant effect of the compost. Single DCD (T1) reduced CO2 emission by 7.02 % and increased humic acid content by 3.09 %. DCD+SSP (T2) resulted in a 15.26 % reduction in CO2 emission, a 9.13 % increase in humic acid content, and a significant increase in compost humification level. Furthermore, DCD+SSP improved the abundance and diversity of the CCAM (mainly Proteobacteria and Actinobacteria), improved the compost microenvironment and reduced carbon loss by 6.89 %. Redundancy analysis (RDA) showed that CCAM community had strong correlations with TOC (84.8 %). This study results provided theoretical and practical support for further exploring the carbon emission reduction in composting and promoting sustainable agricultural development.

Improving the anaerobic digestion of sewage sludge by adding cobalt nanoparticles

ABSTRACT This work evaluated the effects of cobalt nanoparticles (CoNPs) (0.025–7 mg/gVS) on the intensification of sewage sludge anaerobic digestion (AD) using biochemical methane potential (BMP) tests. This study was motivated by the need to improve the efficiency and stability of anaerobic digestion of sewage sludge, a critical process in waste management and renewable energy production. The effects at doses less than 2 mg/gVS were not substantial, but 3–7 mg/gVS improved the performance. The maximum biogas yield was 232 mL/gVS (at a dose of 7 mg/gVS), whereas it was 132 mL/gVS in the control (zero dose). Similarly, the reductions in the volatile solids and methane contents reached maxima of 16 and 74.3%, respectively. The analyses of volatile fatty acids, redox potential, and electron transfer system activity indicated that the addition of CoNPs stimulated the early stages of AD. Finally, acetate consumption and the increase in CH4 content suggested that CoNPs positively affected system stability and acetoclastic methanogenesis. That is, CoNPs effectively intensified the behaviour and stability of the anaerobic process. The novelty of this research lies in the comprehensive evaluation of the effects of CoNPs across a wide range of doses on sewage sludge AD, providing new insights into the optimisation of this process for increased biogas production and organic matter reduction.

Anatomy of a fumarole field: drone remote-sensing and petrological approaches reveal the degassing and alteration structure at La Fossa cone, Vulcano, Italy

Abstract. Hydrothermal alteration and mineralization processes can affect the physical and chemical properties of volcanic rocks. Aggressive acidic degassing and fluid flow often also lead to changes in the appearance of a rock, such as changes in surface coloration or intense bleaching. Although hydrothermal alteration can have far-reaching consequences for rock stability and permeability, limited knowledge exists on the detailed structures, extent, and dynamic changes that take place near the surface of hydrothermal venting systems. By integrating drone-based photogrammetry with mineralogical and chemical analyses of rock samples and surface gas flux, we investigate the structure of the evolving volcanic degassing and alteration system at the La Fossa cone on the island of Vulcano, Italy. Our image analysis combines principal component analysis (PCA) with image classification and thermal analysis through which we identify an area of approximately 70 000 m2 that outlines the maximum extent of hydrothermal alteration effects at the surface, represented by a shift in rock color from reddish to gray. Within this area, we identify distinct gradients of surface coloration and temperature that indicate a local variability in the degassing and alteration intensity and define several structural units within the fumarole field. At least seven such larger units of increased activity could be constrained. Through mineralogical and geochemical analysis of samples from the different alteration units, we define a relationship between surface appearance in drone imagery and the mineralogical and chemical composition. Gradients in surface color from reddish to gray correlate with a reduction in Fe2O3 from up to 3.2 % in the unaltered regime to 0.3 % in the altered regime, and the latter coincides with the area of increased diffuse acid gas flux. As the pixel brightness increases towards higher alteration gradients, we note a loss of the initial (igneous) mineral fraction and a change in the bulk chemical composition with a concomitant increase in sulfur content from close to 0 % in the unaltered samples to up to 60 % in samples from the altered domains. Using this approach of combined remote-sensing and in situ analyses, we define and spatially constrain several alteration units and compare them to the present-day thermally active surface and degassing pattern over the main crater area. The combined results permit us to present a detailed anatomy of the La Fossa fumarole field, including high-temperature fumaroles and seven larger units of increased alteration intensity, surface temperature, and variably intense surface degassing. Importantly, we also identify apparently sealed surface domains that prevent degassing, likely as a consequence of mineral precipitation from degassing and alteration processes. By assessing the thermal energy release of the identified spatial units quantitatively, we show that thermal radiation of high-temperature fumaroles accounts for < 50 % of the total thermal energy release only and that the larger part is emitted by diffuse degassing units. The integrated use of methods presented here has proven to be a useful combination for a detailed characterization of alteration and activity patterns of volcanic degassing sites and has the potential for application in alteration research and for the monitoring of volcanic degassing systems.

Pickering emulsions based on ovalbumin‐ferulic acid‐sodium alginate supramolecular hydrogels: application to cookies replacing margarine

SummaryMargarine contains trans fatty acids, which have been linked to adverse effects on human health. It is therefore of the utmost importance to develop superior margarine substitutes for use in baked foods. The protein‐polyphenol‐polysaccharide ternary supramolecular system displays remarkable stability and can be utilised in the formulation of emulsions for partial margarine replacement. The aim of this study was to examine the stability of an ovalbumin (OVA)‐ferulic acid (FA)‐sodium alginate (SA) ternary supramolecular emulsion with varying water‐to‐oil ratios. The emulsion was evaluated for its potential as a substitute for margarine in cookies. The findings revealed that the specific emulsion instability of the system initially increased and subsequently decreased with an increase in corn oil content, reaching an optimal point of stability and dispersibility at a water‐to‐oil ratio of 5:11. As the emulsion was incorporated into the cookie dough at levels ranging from 0% to 100% margarine, the viscoelasticity of the dough was enhanced and the hardness was reduced. As the emulsion content increased in place of margarine, the cookies exhibited visible cracks on the surface, accompanied by an increase in hardness, baking loss rate and a notable change in colour. The cookies demonstrated the optimal quality when the emulsion content was 40%.

Production of Bio-Oil from Sugarcane Bagasse through Hydrothermal Liquefaction Processes with Modified Zeolite Socony Mobil-5 Catalyst

In response to the increasing global demand for sustainable energy alternatives, this research explores the efficient conversion of sugarcane bagasse to bio-oil through hydrothermal liquefaction (HTL) processes with modified Zeolite Socony Mobil-5 catalysts (ZSM-5). The study systematically investigates the impact of feedstock quantity, reaction temperature, duration, and catalyst loading on bio-oil yield and quality. Optimisation experiments revealed that a feedstock amount of 10 grammes, an HTL temperature of 340 °C for 60 min and a ZSM-5 catalyst loading of 3 grammes resulted in the highest bio-oil yield. Furthermore, the introduction of Ni and Fe metals to ZSM-5 exhibited enhanced catalytic activity without compromising the structure of the zeolites. Comprehensive characterisation of modified catalysts using SEM-EDS, XRD, TGA, TEM, and FTIR provided insight into their structural and chemical properties. The successful incorporation of Ni and Fe into ZSM-5 was confirmed, highlighting promising applications in hydrothermal liquefaction. Gas chromatography–mass spectrometry (GC-MS) analysis of bio-oils demonstrated the effectiveness of the 2% Fe/ZSM-5 catalyst, highlighting a significant increase in hydrocarbon content. FTIR analysis of the produced bio-oils indicated a reduction in functional groups and intensified aromatic peaks, suggesting a shift in chemical composition favouring aromatic hydrocarbons. This study provides valuable information on HTL optimisation, catalyst modification, and bio-oil characterisation, advancing the understanding of sustainable biofuel production. The findings underscore the catalytic prowess of modified ZSM-5, particularly with iron incorporation, in promoting the formation of valuable hydrocarbons during hydrothermal liquefaction.

Mechanism analysis of enhanced desulfurization of pulverized coal through high-gradient magnetic separation with microwave radiation

Dry high gradient magnetic separation technology is a low-carbon green technology. It can be embedded in a power plant to remove coal pyrite with a high-efficiency magnetic separator and remarkable magnetic properties difference between coal pyrite and coal matrix. This study selected the microwave radiation method to improve the magnetic properties difference and carried out a desulfurization experiment with a self-developed high-gradient permanent magnetic separator using the tapered iron auxiliary magnetic pole. The results demonstrate that the pyrite content and specific magnetic susceptibility increase with the decrease in particle size. The desulfurization rate did not change significantly at 25 °C. The coal sample began to appear in the thermal reaction at 450 °C, and the pyrite can become a strong magnetic property pyrrhotite. The desulfurization rate can achieve 58.70 % at 700 °C, and is equivalent to the wet washing index, due to the supply of high magnetic field force. The dynamic characteristic response of magnetic particles becomes more obvious with short time adsorption, and the probability of carrying non-magnetic particles is reduced. This study demonstrates that the high-gradient magnetic separation technology of pulverized coal enhanced by microwave irradiation is feasible.

Soil Formation on Loamy Deposits in Technogenic Landscapes of the Taiga Zone in the North-Eastern Part of European Russia

The paper highlights the influence of moisture on the soil formation process on loamy deposits during the primary vegetation succession. The study was carried out in the north-eastern part of European Russia (Komi Republic) in the middle taiga subzone. The authors analyzed young soils on the territory of a quarry for extraction of loamy grounds and background soils in the vicinity of it. Planting the Siberian spruce cultures on the territory of the quarry activated formation of the tree layer and thereby accelerated formation of the zonal type soils. The third succession decade in drained conditions saw formation of organic soil horizons (litters), a decrease in soil density in the upper profile part, a tendency to redistribute and differentiate the silty fraction by one-and-a-half oxides, indicating the beginning of selective podzolization. The rise in soil moisture content increased conservation of organic residues (peat formation) and made gley formation active. The quarry soils, like background soils, increased in acidity, carbon and nitrogen reserves along with the soil moisture content increase. In automorphic soil formation conditions, the rate of organic carbon accumulation in the upper 0–20-cm layer is 0.4 t· ha–1·year1; the excessive soil moisture content further increased it (1.0–1.2 t·ha–1·year1). The reserves of Corg in the upper 20-cm soil layer of young soils are by 2–4 times less than those in background soils.

Compressive and flexural properties and damage modes of aluminum foam/epoxy resin interpenetrating phase composites reinforced by silica powder

AbstractInterpenetrating phase composites (IPCs) can combine the advantages of each component and have a good application prospect. IPCs were prepared by combining open‐cell aluminum foam (AF) and epoxy resin (EP) in three‐dimensional space in this study. Different contents of silica powder (SP, 80, 100, 120, and 140 wt%) were added to EP to improve the compressive and three‐point bending properties of IPCs. In the bending test, acoustic emission (AE) was applied to track the bending deformation of the samples, and k‐means clustering algorithm was applied to identify the damage modes. The compressive and bending properties of IPCs increased first and then decreased with the increase of SP content, and reached the maximum when the SP content was 100 wt%, with a compressive yield strength of 74.6 MPa and a bending peak load of 1.96 kN. The performance degradation was mainly attributed to the AF/EP debonding due to SP distribution at the interface. The X‐type shear band and EP/AF debonding appeared in compression failures of AF and IPCs, respectively. The AE clustering results showed that under bending load, plastic deformation of matrix (60–200 kHz) and fracture failure (230–340 kHz) modes appeared in AF, while EP/AF debonding (60–120 kHz), EP failure (120–230 kHz) and plastic deformation of foam matrix (230–250 kHz) modes appeared in IPCs.Highlights Silica powder was added to improve compressive and bending properties of IPCs. Acoustic emission was used to monitor bending of foam and IPCs firstly. k‐means clustering was used to identify and classify bending damage patterns.