Measurement Of Inclination Angle Research Articles

Dual-axis fiber Bragg grating tilt sensor based on universal joint structure

Inclination angle measurement is widely used in fields such as infrastructure health, power engineering safety, and earthquake monitoring. In response to the problem that existing inclinometers based on the pendulum structure can only measure a single axial inclination angle, a dual-axis Fiber Bragg Grating (FBG) tilt sensor based on a universal joint structure is proposed. SolidWorks was used to establish a sensor model and conduct theoretical analysis. The structural parameters of the sensor were optimized using the control variable method. Based on the optimization results, a physical sensor was developed, and an inclination and temperature testing system was set up for performance testing. The results show that within a measurement range of ± 5°, the sensitivities of the X and Y axes of the sensor are 229.8 pm/° and 224.9 pm/°, respectively, with a resolution of approximately 4.4 × 10-4°. The tilt accuracy of the sensor is approximately 0.48°, and it exhibits good creep resistance and stability during long-term measurements, as well as temperature self-compensation capabilities. The research results provide a new reference for the development of similar dual-axis tilt measurement sensors.

A three-dimensional algorithm for precise measurement of human auricle parameters

Measurement of auricle parameters for planning and post-operative evaluation presents substantial challenges due to the complex 3D structure of the human auricle. Traditional measurement methods rely on manual techniques, resulting in limited precision. This study introduces a novel automated surface-based three-dimensional measurement method for quantifying human auricle parameters. The method was applied to virtual auricles reconstructed from Computed Tomography (CT) scans of a cadaver head and subsequent measurement of important clinically relevant aesthetical auricular parameters (length, width, protrusion, position, auriculocephalic angle, and inclination angle). Reference measurements were done manually (using a caliper and using a 3D landmarking method) and measurement precision was compared to the automated method. The CT scans were performed using both a contemporary high-end and a low-end CT scanner. Scans were conducted at a standard scanning dose, and at half the dose. The automatic method demonstrated significantly higher precision in measuring auricle parameters compared to manual methods. Compared to traditional manual measurements, precision improved for auricle length (9×), width (5×), protrusion (5×), Auriculocephalic Angle (5–54×) and posteroanterior position (23×). Concerning parameters without comparison with a manual method, the precision level of supero-inferior position was 0.489 mm; and the precisions of the inclination angle measurements were 1.365 mm and 0.237 mm for the two automated methods investigated. Improved precision of measuring auricle parameters was associated with using the high-end scanner. A higher dose was only associated with a higher precision for the left auricle length. The findings of this study emphasize the advantage of automated surface-based auricle measurements, showcasing improved precision compared to traditional methods. This novel algorithm has the potential to enhance auricle reconstruction and other applications in plastic surgery, offering a promising avenue for future research and clinical application.

Research and application of a flexible measuring array for deep displacement of landslides

Abstract. The multidimensional and multi-sliding surface measurement of deep-seated displacement on landslides poses a significant technical challenge in landslide monitoring and early warning. The fixed-borehole inclinometer serves as an important measurement method based on drilling for this purpose. In this study, a novel flexible measurement array for deep-seated landslide displacement and its installation and measurement processes were developed, enabling higher accuracy in full-hole multidimensional deformation measurement. The measurement array consists of individual measurement probes as basic units, connected in series through coaxial cables and high-pressure rubber hoses, forming a flexible measurement array. Each probe is equipped with acceleration and magnetic field sensors, allowing for the measurement of borehole inclination and azimuth angles and providing a more comprehensive understanding of the deformation of deep-seated landslides. This flexible measurement array resolves the limitations of traditional fixed inclinometers, such as limited probe quantity or inaccurate installation positions that fail to reflect the deformation trend of the landslide body. Moreover, it eliminates the need for auxiliary installation accessories like pulleys and inclinometer pipes, simplifying the mechanical structure and installation process, which represents an advancement in methodology and an improvement in measurement techniques. This array provides a more comprehensive and improved monitoring tool for disaster prevention and mitigation, thereby enhancing the level of geological hazard monitoring and early warning technology.

Restoration of the Tully–Fisher Relation by Statistical Rectification

I employ the Lucy rectification algorithm to recover the inclination-corrected distribution of local disk galaxies in the plane of absolute magnitude (M i ) and H i velocity width (W 20). By considering the inclination angle as a random variable with a known probability distribution, the novel approach eliminates one major source of uncertainty in studies of the Tully–Fisher relation: inclination angle estimation from axial ratio. Leveraging the statistical strength derived from the entire sample of 28,264 H i-selected disk galaxies at z < 0.06 from the Arecibo Legacy Fast ALFA survey, I show that the restored distribution follows a sharp correlation that is approximately a power law between −16 > M i > −22: Mi=M0−2.5β[log(W20/250km/s)] , with M 0 = −19.77± 0.04 and β = 4.39 ± 0.06. At the brighter end (M i < −22), the slope of the correlation decreases to β ≈ 3.3, confirming previous results. Because the method accounts for measurement errors, the intrinsic dispersion of the correlation is directly measured: σ(logW20)≈0.06 dex between −17 > M i > −23, while σ(M i ) decreases from ∼0.8 in slow rotators to ∼0.4 in fast rotators. The statistical rectification method holds significant potential, especially in the studies of intermediate-to-high-redshift samples, where limited spatial resolution hinders precise measurements of inclination angles.

Auto-LIA: The Automated Vision-Based Leaf Inclination Angle Measurement System Improves Monitoring of Plant Physiology.

Plant sensors are commonly used in agricultural production, landscaping, and other fields to monitor plant growth and environmental parameters. As an important basic parameter in plant monitoring, leaf inclination angle (LIA) not only influences light absorption and pesticide loss but also contributes to genetic analysis and other plant phenotypic data collection. The measurements of LIA provide a basis for crop research as well as agricultural management, such as water loss, pesticide absorption, and illumination radiation. On the one hand, existing efficient solutions, represented by light detection and ranging (LiDAR), can provide the average leaf angle distribution of a plot. On the other hand, the labor-intensive schemes represented by hand measurements can show high accuracy. However, the existing methods suffer from low automation and weak leaf-plant correlation, limiting the application of individual plant leaf phenotypes. To improve the efficiency of LIA measurement and provide the correlation between leaf and plant, we design an image-phenotype-based noninvasive and efficient optical sensor measurement system, which combines multi-processes implemented via computer vision technologies and RGB images collected by physical sensing devices. Specifically, we utilize object detection to associate leaves with plants and adopt 3-dimensional reconstruction techniques to recover the spatial information of leaves in computational space. Then, we propose a spatial continuity-based segmentation algorithm combined with a graphical operation to implement the extraction of leaf key points. Finally, we seek the connection between the computational space and the actual physical space and put forward a method of leaf transformation to realize the localization and recovery of the LIA in physical space. Overall, our solution is characterized by noninvasiveness, full-process automation, and strong leaf-plant correlation, which enables efficient measurements at low cost. In this study, we validate Auto-LIA for practicality and compare the accuracy with the best solution that is acquired with an expensive and invasive LiDAR device. Our solution demonstrates its competitiveness and usability at a much lower equipment cost, with an accuracy of only 2. 5° less than that of the widely used LiDAR. As an intelligent processing system for plant sensor signals, Auto-LIA provides fully automated measurement of LIA, improving the monitoring of plant physiological information for plant protection. We make our code and data publicly available at http://autolia.samlab.cn.

A clinical comparison of sagittal condylar inclination and Bennett angle derived from a conventional electronic tracking device and an optical jaw tracking device

The challenges of conventional methods to measure the sagittal condylar inclination and the Bennett angle include patient discomfort and an output of averaged values calculated on the arc of mandibular movement. Programming these average values into a mechanical or mathematically simulated articulator may introduce occlusal errors. The purpose of this clinical study was to compare the sagittal condylar inclination and Bennett angle measurements derived from a conventional electronic tracking device and an optical tracking device. Fifteen dentate participants with at least 12 occluding units, 25 years old and above, participated in the study. Each participant's mandibular movements were recorded by the 2 systems for different condylar guidance values. A conventional tracking device, the Cadiax Compact 2, and an optical tracking device, the MODJAW, were used for this study. Sagittal condylar inclination was measured at 3mm and 5mm using protrusive records and the values of the Bennett angle at 3mm were measured using excursive records along the path traced by mandibular condyles. The Wilcoxon signed-rank test was used to analyze the paired data from the 2 methods. A significant difference was found between right (P=.007) and left sagittal condylar inclinations (P=.010) measured at 3mm with the conventional and optical tracking devices. A significant difference was found between right (P=.015) and left sagittal condylar inclinations (P=.004) measured at 5mm with the conventional and optical tracking devices. The right and left Bennett angles measured at 3mm with the conventional and optical tracking devices were statistically different (P=.043 and P=.035 respectively). The sagittal condylar inclination and Bennett angle measured at different positions along the path of movement exhibited significant differences. The sagittal condylar inclination and Bennett angle values obtained from the conventional tracking device were generally significantly less than those derived from the optical tracking device.

Automatic Branch-Leaf Segmentation and Leaf Phenotypic Parameter Estimation of Pear Trees Based on Three-Dimensional Point Clouds.

The leaf phenotypic traits of plants have a significant impact on the efficiency of canopy photosynthesis. However, traditional methods such as destructive sampling will hinder the continuous monitoring of plant growth, while manual measurements in the field are both time-consuming and laborious. Nondestructive and accurate measurements of leaf phenotypic parameters can be achieved through the use of 3D canopy models and object segmentation techniques. This paper proposed an automatic branch-leaf segmentation pipeline based on lidar point cloud and conducted the automatic measurement of leaf inclination angle, length, width, and area, using pear canopy as an example. Firstly, a three-dimensional model using a lidar point cloud was established using SCENE software. Next, 305 pear tree branches were manually divided into branch points and leaf points, and 45 branch samples were selected as test data. Leaf points were further marked as 572 leaf instances on these test data. The PointNet++ model was used, with 260 point clouds as training input to carry out semantic segmentation of branches and leaves. Using the leaf point clouds in the test dataset as input, a single leaf instance was extracted by means of a mean shift clustering algorithm. Finally, based on the single leaf point cloud, the leaf inclination angle was calculated by plane fitting, while the leaf length, width, and area were calculated by midrib fitting and triangulation. The semantic segmentation model was tested on 45 branches, with a mean Precisionsem, mean Recallsem, mean F1-score, and mean Intersection over Union (IoU) of branches and leaves of 0.93, 0.94, 0.93, and 0.88, respectively. For single leaf extraction, the Precisionins, Recallins, and mean coverage (mCoV) were 0.89, 0.92, and 0.87, respectively. Using the proposed method, the estimated leaf inclination, length, width, and area of pear leaves showed a high correlation with manual measurements, with correlation coefficients of 0.94 (root mean squared error: 4.44°), 0.94 (root mean squared error: 0.43 cm), 0.91 (root mean squared error: 0.39 cm), and 0.93 (root mean squared error: 5.21 cm2), respectively. These results demonstrate that the method can automatically and accurately measure the phenotypic parameters of pear leaves. This has great significance for monitoring pear tree growth, simulating canopy photosynthesis, and optimizing orchard management.

Identification of Gas-Water Two-Phase Flow Patterns in Horizontal Wells of Shale Gas Reservoirs Based on Production Logging Data

In order to clarify the gas-water two-phase flow law in horizontal wells and study the gas-water two-phase flow characteristics in horizontal wells, firstly, the gas-water two-phase in a horizontal well is numerically simulated and analyzed, and the flow pattern distribution under different well inclination angles and different phase separation flow rates is obtained. Secondly, a series of production logging instruments including CAT instrument was used to conduct experimental research on gas-water two-phase flow under different flow conditions, and the measured values of each CAT probe were extracted to reflect the local holdup under different flow patterns. Finally, SSA-BP neural network algorithm is used to identify a gas-water two-phase flow pattern in a wellbore by using experimental parameters such as center holdup, well inclination angle, spinner revolution, and CAT probe measurements. The recognition accuracy of the neural network was improved from 83.75% to 91.66%, and the operation speed was accelerated. It provides a research idea to explore the flow characteristics of gas-water two-phase flow in horizontal wells.

Computed tomographic angular measurements using a bone-centered three-dimensional coordinate system are accurate in a femoral torsional deformity model and precise in clinical canine patients.

In small animal orthopedics, angular measurements in the canine femur are often applied in clinical patients with bone deformities and especially in complex and severe cases. Computed tomography (CT) has been shown to be more precise and accurate than two-dimensional radiography, and several methods are described. Measurement techniques evaluated in normal bones must prove accuracy in deformed bones in clinical settings. The goals of our study were to evaluate the accuracy of canine femoral torsion angle measurements in a femoral torsional deformity model and to test repeatability and reproducibility of canine femoral neck inclination, torsion, and varus angle measurements in CT datasets of dogs applying a CT-based technique using a three-dimensional (3D) bone-centered coordinate system. For precision testing, femoral torsion, femoral neck inclination, and femoral varus angles were measured in CT data of 68 canine hind limbs by two operators, and their results were compared. For accuracy testing, a femoral torsional deformity model was preset from 0° to +/-90° with a goniometer and scanned. Torsion angles were measured in the CT data and compared to the preset value. In the femoral torsion model, the Bland-Altman plots demonstrated a mean difference of 2.11°, and the Passing-Bablok analysis demonstrated a correlation between goniometer and CT-based measurements. In the clinical CT scans, intra- and interobserver agreement resulted in coefficients of variation for repeated measurements (%) between 1.99 and 8.26 for the femoral torsion, between 0.59 and 4.47 for the femoral neck inclination, and between 1.06 and 5.15 for the femoral varus angles. Evaluation of femoral malformations with torsional deformities is the target area of this technique. Further studies are required to assess its value in different types, degrees, and combinations of osseous deformities and to establish normal reference values and guidelines for corrective osteotomies. Based on the results of this study, the accuracy of the torsion angle measurements and the precision of inclination, torsion, and the varus angle measurements were considered acceptable for clinical application.

Radiological Evaluation of the Relationship Between Plantar Fasciitis and Foot Arch Angles in Adults

Objective: The foot arch deformation increases plantar fasciitis (PF) and plantar calcaneal spur (PCS) for-mation. As a result, the heel fat pad becomes thinner. This study investigated the relationship between plantar fasciitis and foot arch angles. Methods: We performed a retrospective review of patients who had PF patients (n = 53) and healthy individu-als (n = 71) without PF. We have evaluated the presence of PCS and heel fat pad thickness measurements on magnetic resonance imaging (MRI), and the lateral talus-first metatarsal angle (Meary’s angle), lateral talocal-caneal angle, and calcaneal inclination angle measurements were performed on X-ray images. Results: The mean age of the PF group was significantly higher than the control group (p = 0.001). The degrees of Meary’s angle and calcaneus inclination angle were significantly higher in the PF group (p &amp;lt; 0.001 and p = 0.026, respectively) than in the control group. The incidence of PCS was significantly higher in the PF group (p = 0.028). In the binary logistic regression analysis model, high Meary’s angle and calcaneal pitch angle were found to be associated with the risk of PF. There was also a significant association between age and the pres-ence of PCS and PF. Conclusion: Changes in Meary’s angle and calcaneal pitch angle were significant risk factors for PF.

Millimeter Wave Attenuation Due to Wind and Heavy Rain in a Tropical Region.

Millimeter wave fixed wireless systems in future backhaul and access network applications can be affected by weather conditions. The losses caused by rain attenuation and antenna misalignment due to wind-induced vibrations have greater impacts on the link budget reduction at E-band frequencies and higher. The current International Telecommunications Union Radiocommunication Sector (ITU-R) recommendation has been widely used to estimate rain attenuation, and the recent Asia Pacific Telecommunity (APT) report provides the model to estimate the wind-induced attenuation. This article provides the first experimental study of the combined rain and wind effects in a tropical location using both models at a frequency in the E band (74.625 GHz) and a short distance of 150 m. In addition to using wind speeds for attenuation estimation, the setup also provides direct antenna inclination angle measurements using the accelerometer data. This solves the limitation of relying on the wind speed since the wind-induced loss is dependent on the inclination direction. The results show that the current ITU-R model can be used to estimate the attenuation of a short fixed wireless link under heavy rain, and the addition of wind attenuation via the APT model can estimate the worst-case link budget during high wind speeds.

Are CPR (Contact Patch to Rim) distance anomalies associated with the occurrence of abnormal noises from ceramic-on-ceramic THA?

IntroductionThe ceramic-on-ceramic couple in total hip arthroplasties (THA) has the advantage of excellent wear resistance and the bioinert nature of its debris. Noise occurring from this friction torque is a common complication, the contributing factors of which are debated. The noise is caused by a lack of lubrication, due in most part to the positioning of the acetabular cup. The study of metal-on-metal couples identified that the calculation of the Contact Patch to Rim (CPR) distance provides information on lubrication defects and also that it is correlated with the wear of metal-on-metal implants. This CPR distance is not recognized to be correlated with the occurrence of noise for the ceramic-on-ceramic couple at a caliber ≤ 36mm. We therefore conducted a retrospective case-control study to assess: 1) The influence of the CPR distance on noise occurrence; 2) Whether other factors associated to noise occurrence exist? HypothesisOur hypothesis was that a low CPR distance was correlated with noise occurrence. MethodThis was a case-control study with 3 controls for each case, analyzing 21 THAs (21 patients) with noise compared to 63 THAs without noise (63 patients) matched for age, sex and body mass index. These patients were taken from a continuous retrospective series of 96 patients for 104 total hip arthroplasties (THA) with a single operator and 4th generation Biolox Delta ceramic-on-ceramic single implant, performed between 2007 and 2012. The calculation of the CPR distance was then performed for both groups using measurements of inclination angles, anteversion angles, and implant data regarding the head/insert contact angle, head/insert diameter and clearance. ResultsAt the mean follow-up of 7.1 years±1.2 [5 to 9.6], the mean CPR distance was lower in the noise group 10mm±3.3 [3.8 to 16.4] than in the control group 14.8mm±4.3 [7.3 to 24.4] (p=0.0007). The mean inclination angle was higher in the noise group 45.1°±7.8 [31 to 62] than in the control group 41.2°±7.2 [26 to 56] (p=0.04). The occurrence of noise was independent of anteversion, head caliber, cup diameter, neck length and stem size, and stem type (standard or lateralized). ConclusionA low CPR distance was correlated with the occurrence of noises, similarly a steep inclination was correlated with the occurrence of noises. Level of evidenceIII; Retrospective case-control study.

Prospects of calibrating afterglow modeling of short GRBs with gravitational wave inclination angle measurements and resolving the Hubble tension with a GW-GRB association event

In the past decades, an external forward shock model has been successfully developed to explain the main features of the afterglow emission of gamma-ray bursts (GRBs). In the numerical modeling of the GRB afterglow, some approximations have been made for simplicity, and different groups developed their codes. A robust test of these models/approaches is challenging because of the lack of directly measured physical parameters. Fortunately, the viewing angle inferred from the afterglow modeling is widely anticipated to be the same as the inclination angle of the binary neutron star (BNS) mergers that can be evaluated with the gravitational wave (GW) data. Therefore, in the future, it is possible to calibrate the afterglow modeling with the GW inclination angle measurements. We take three methods, including both analytical estimations and direct simulations, to project the uncertainties of the inclination angle measurements. For some BNS mergers accompanied with electromagnetic counterparts detected in the O4/O5 runs of LIGO/Virgo/KAGRA/LIGO-India detectors, we show that the inclination angle can be determined within an uncertainty of $\ensuremath{\le}0.1\text{ }\text{ }\mathrm{rad}$, supposing that the Hubble constant is known with an accuracy of $\ensuremath{\le}3%$ and the uncertainty of Hubble flow velocity is within $\ensuremath{\sim}1%$. The off-axis GRB outflow will give rise to afterglow emission, and the most energetic ones may be detectable at the distance of $\ensuremath{\sim}100--200\text{ }\text{ }\mathrm{Mpc}$ even for a viewing angle of $\ensuremath{\ge}0.3\text{ }\text{ }\mathrm{rad}$. Such events can thus serve as a robust test of the afterglow modeling approach. We have also evaluated the prospect of resolving the so-called Hubble tension with a single GW/GRB association event. We find out that a $\ensuremath{\sim}3%$ precision Hubble constant is obtainable if the uncertainty of the viewing angle can be constrained to be within $\ensuremath{\sim}0.1\text{ }\text{ }\mathrm{rad}$, which is expected to be the case for some nearby ($\ensuremath{\le}250\text{ }\text{ }\mathrm{Mpc}$) bright/on-axis GRBs with a well-behaved afterglow light curve displaying a clear achromatic break at early times.

XMM–Newton observations of the narrow-line Seyfert 1 galaxy IRAS 13224−3809: X-ray spectral analysis II

ABSTRACT Previously, we modelled the X-ray spectra of the narrow-line Seyfert 1 galaxy IRAS 13224−3809 using a disc reflection model with a fixed electron density of 1015 cm−3. An additional blackbody component was required to fit the soft X-ray excess below 2 keV. In this work, we analyse simultaneously five flux-resolved XMM–Newton spectra of this source comprising data collected over 2 Ms. A disc reflection model with an electron density of ne ≈ 1020 cm−3 and an iron abundance of $Z_{\rm Fe}=3.2\pm 0.5\, \mathrm{Z}_{\odot }$ is used to fit the broad-band spectra of this source. No additional component is required to fit the soft excess. Our best-fitting model provides consistent measurements of black hole spin and disc inclination angle as previous models where a low disc density was assumed. In the end, we calculate the average illumination distance between the corona and the reflection region in the disc of IRAS 13224−3809 based on best-fitting density and ionization parameters, which changes from 0.43$\sqrt{f_{\rm AD}/f_{\rm INF}}$ rg in the lowest flux state to 1.71$\sqrt{f_{\rm AD}/f_{\rm INF}}$ rg in the highest flux state assuming a black hole mass of $2\times 10^{6}\, \mathrm{M}_{\odot }$. fAD/fINF is the ratio between the flux of the coronal emission that reaches the accretion disc and infinity. This ratio depends on the geometry of the coronal region in IRAS 13224−3809. So we only discuss its value based on the simple ‘lamppost’ model, although detailed modelling of the disc emissivity profile of IRAS 13224−3809 is required in future to reveal the exact geometry of the corona.

Association of mobility capacity with the masses and amounts of intramuscular non-contractile tissue of the trunk and lower extremity muscles in community-dwelling older adults.

We examined the association of mobility capacity with muscle thicknesses and echo intensities of the trunk and lower extremity muscles measured using an ultrasound imaging device in community-dwelling older adults. The participants were 57 community-dwelling older adults. Mobility capacity was assessed based on the measurement of usual and maximal walking speeds and timed up-and-go (TUG) time. Muscle thickness and echo intensity of the trunk and lower extremity muscles were measured using an ultrasound imaging device. Finally, sagittal spinal alignment was assessed based on the measurement of thoracic kyphosis, lumbar lordosis, and sacral anterior inclination angles in the standing position using a Spinal Mouse. Stepwise regression analysis showed that the tibialis anterior muscle thickness, tibialis posterior muscle echo intensity, and body weight were significant and independent factors of usual walking speed, with a coefficient of determination (R2) of 0.25. The thicknesses of the thoracic erector spinae and obliquus externus abdominis muscles were significant and independent factors of maximal walking speed (R2=0.26). Moreover, only age was a significant and independent factor for TUG time (R2=0.10). The results of this study suggested associations 1) between slow usual walking speed and low tibialis anterior muscle thicknesses and high echo intensity of the tibialis posterior muscle and 2) between slow maximal walking speed and low thoracic erector spinae and obliquus externus abdominis thicknesses in community-dwelling older adults.

Medición del Ángulo de Inclinación del Ligamento Cruzado Anterior (LCA). Serie de Casos

BackgroundThe evaluation of the inclination of the anterior cruciate ligament (ACL) is useful to clarify diagnostic doubts in patients who have not been taken to reconstructive procedures and to evaluate the quality and effectiveness of restoring the anatomical attachments of the ligament. after an ACL surgery reconstruction. However, in our environment there is no local measurement reference or training in measuring it inclination angle. The aim of the study is to measure the inclination angle of the ACL in healthy knees of our population, using magnetic resonance (MRI) measurement techniques. MethodsA Case Series study was performed, including patients who underwent to knee MRI between June 2013 and June 2017 that were read as normal. Inclination angle measurements of the ACL were taken in the sagittal, coronal, and axial planes. Results91 patients were included (45% (n=41) Men / 55% (n=50) Women). An ACL inclination angle was found in the sagittal plane with a mean of 45.31 (SD: 5.39), in the coronal plane of 70.68 (SD: 5.79) and 68.49 (SD: 5.61) in the axial plane, with no imaging differences found. segmented by sex, age or laterality. DiscussionThere are no differences in the MRI images in the angle of inclination in any of the three planes between men and women, neither with regard to laterality or age groups. Results were obtained that have not yet been described in the literature; those obtained are similar to those reported in the literatureEvidence Level: IV.

Long-distance transequatorial navigation using sequential measurements of magnetic inclination angle.

Diverse taxa use Earth's magnetic field in combination with other sensory modalities to accomplish navigation tasks ranging from local homing to long-distance migration across continents and ocean basins. Several animals have the ability to use the inclination or tilt of magnetic field lines as a component of a magnetic compass sense that can be used to maintain migratory headings. In addition, a few animals are able to distinguish among different inclination angles and, in effect, exploit inclination as a surrogate for latitude. Little is known, however, about the role that magnetic inclination plays in guiding long-distance migrations. In this paper, we use an agent-based modelling approach to investigate whether an artificial agent can successfully execute a series of transequatorial migrations by using sequential measurements of magnetic inclination. The agent was tested with multiple navigation strategies in both present-day and reversed magnetic fields. The findings (i) demonstrate that sequential inclination measurements can enable migrations between the northern and southern hemispheres, and (ii) demonstrate that an inclination-based strategy can tolerate a reversed magnetic field, which could be useful in the development of autonomous engineered systems that must be robust to magnetic field changes. The findings also appear to be consistent with the results of some animal navigation experiments, although whether any animal exploits a strategy of using sequential measurements of inclination remains unknown.

Leaf inclination angle and foliage clumping in an evergreen broadleaf

How leaves are presented affects interaction of atmospheric CO2, energy (light), and plant physiology. Plant productivity is primarily determined by the amount of leaf area, leaf orientation and distribution in space. Not much attention has been paid to possible changes in leaf orientation and distribution with elevated CO2, but its effect on plant growth could alter the proportions of sunlit and shaded leaf areas and feedback on carbohydrate available for further growth. We report on first measurements of leaf inclination angle distribution and foliage clumping in a native evergreen Eucalyptus woodland in ambient CO2 and under +150 ppm elevated CO2. We found that a spherical leaf angle distribution was not an appropriate supposition for present species (Eucalyptus tereticornis Sm.) at this site. Our measurements of leaf inclination angles from imagery indicated an erectophile, highly skewed unimodal leaf inclination angle distribution function. We conclude that despite the measured steeper angles under elevated CO2 concentrations, the leaf angle change is not significant and falls within the expected natural variability and uncertainties connected with the measurement method. The lack of a clear response of leaf orientation and foliage clumping to elevated CO2 concentration indicates that the previously produced datasets of leaf inclination angles and foliage clumping maps with Earth observation data may be suitable while modelling carbon and water cycles under climate change.

Why “swimming crabs” are able to swim – The importance of the axial skeleton: A comparison between the “swimming crab” Liocarcinus depurator and two other brachyuran crabs (Cancer pagurus, Carcinus maenas) using μCT and 3D-reconstruction

Most brachyuran crabs use their pereiopods as walking legs, but there are also a number of species, in which the last (5th) pair of pereiopods (P5) are specialized to permit a unique mode of swimming. One of these P5-swimming crabs is Liocarcinus depurator, commonly found on European shores. We present 3-dimensional μCT-based reconstructions of the axial skeletons and 5th pereiopods (P5), including the intrinsic and extrinsic musculature of the P5, of L. depurator and of two other non-swimming brachyuran crabs, Cancer pagurus and Carcinus maenas. In Liocarcinus, we also present a reconstruction of the 4th pereiopod (P4) together with its intrinsic musculature. We further use 3-dimensional prints of the reconstructed P5 coxa and basi-ischium of L. depurator as well as thoracal parts near the thoracal−coxal arthrodial cavity to build a model which can simulate the effects of muscular activity based on muscle insertions in our 3D reconstruction and under various simulated tensile vectors. This enables us to test muscular functions that had previously been speculated upon. Reconstructed morphological structures are compared to find differences that may explain why of the three species, only L. depurator is able to swim. Significant differences between Liocarcinus and the non-swimmers Cancer and Carcinus were found in the shape of the axial skeleton, external P5 morphology and the dimensions and origin sites of the extrinsic P5 musculature, but not in the intrinsic musculature of the P5. Inclination angle measurements of P1 thoracal−coxal articulation axes against P5 axes showed that in Cancer and Carcinus, angles in the longitudinal plane were smaller than in the lateral one, whereas in Liocarcinus, they were greater. Inclination angles in the longitudinal plane were also much greater in Liocarcinus than in Cancer and Carcinus. 3D print muscular activity simulation showed that muscles inserting at the basi-ischium, which are often referred to as “levator” or “depressor” muscles, may actually also function as promotors or remotors, depending on the tensile vector within which the muscle is acting.

Do All Rigid and Unbalanced Spines Present the Same Risk of Dislocation After Total Hip Arthroplasty? A Comparison Study Between Patients With Ankylosing Spondylitis and History of Spinal Fusion

BackgroundSpines with ankylosis or with a history of lumbosacral fusions have been collectively classified as rigid and unbalanced, and associated with an increased rate of dislocation after total hip arthroplasty (THA). It remains unknown whether the cause of spinal arthrodesis influences the dislocation rate. MethodsA retrospective study was conducted from January 2000 to December 2017, with an institutional review board's approval to identify 2 cohorts with a history of THA: one with ankylosing spondylitis (AS) involving the lumbosacral spine and another cohort with a history of lumbosacral spinal fusion (SF). A chart review was performed to collect demographic and surgical variables. Lumbar lordosis angle (LLA), acetabular anteversion, and inclination angle measurements were taken for each patient. Kaplan-Meier survivorship curves were constructed and multivariable Cox regression was performed for analysis. ResultsThe AS and SF cohorts consisted of 142 and 135 patients, respectively. The SF group had a greater mean LLA (34.18°) than the AS group (21°). A total of 16 patients (11.85%) suffered from dislocation after primary elective THA in the SF group, whereas 4 patients (2.82%) in the AS group. After multivariable Cox regression analysis, increasing LLA and hips outside of the Lewinnek safe zone were found to be associated with a higher hazard of dislocation after THA. ConclusionWe found that the degree of lumbar spine curvature is more associated with dislocation after THA than the history of SF itself; specifically, an increase in lumbar lordosis angle of 1º increases the probability of dislocation by 13% among AS and SF patients.