In-capillary Preconcentration Research Articles

Capillary Electrophoresis-Mass Spectrometry for the Direct Analysis of Metabolites in Highly Saline Samples Using In-Capillary Preconcentration.

Capillary electrophoresis-mass spectrometry (CE-MS) is gaining interest for metabolomics studies because of its high separation efficiency, selectivity, and versatility. The ability to inject nanoliters from only a few microliters of sample in the injection vial makes this approach very suited for volume-limited applications. However, the low injection volumes could compromise the detection sensitivity of CE-MS, thereby potentially limiting its scope in metabolomics. To overcome this issue, online sample preconcentration methods have been developed to increase sample-loading volumes without hampering the intrinsic high separation efficiency of CE. In this protocol, online preconcentration with sample stacking based on pH junction was assessed for the direct profiling of endogenous metabolites in rat brain microdialysates. Sample stacking was realized by a pre-injection of ammonium hydroxide, followed by a large sample injection (i.e., about 17% of the total capillary volume). It is shown that this relatively simple and fast preconcentration procedure is fully compatible with the high-salt concentration in microdialysates and significantly improves the detection sensitivity of the CE-MS method.

Capillary Electrophoresis-Mass Spectrometry with Multisegment Injection and In-Capillary Preconcentration for High-Throughput and Sensitive Determination of Therapeutic Decapeptide Triptorelin in Pharmaceutical and Biological Matrices.

A capillary electrophoresis–tandem mass spectrometry method with a multisegment injection and an in-capillary field-enhanced sample stacking for determination of therapeutic peptide triptorelin in pharmaceutical and biological matrices was developed. The CE separation conditions were optimized in order to obtain maximal separation efficiency, analytical signal intensity and stability, and minimal adsorption of the analyzed peptide onto the capillary wall (1 M formic acid—HFo, pH 1.88). The implementation of the field-enhanced sample injection into CE improved the value of limit of detection 50 times while the multisegment injection increased the sample throughput three times in comparison to a conventional CE approach. The proposed method was characterized by favorable performance parameters, such as linearity (r2 ≥ 0.99), limit of detection (5 ng mL−1 in water matrix, 25 ng mL−1 in plasma matrix), precision (relative standard deviation, 1.5–9.4% for intraday and 2.3–11.9% for interday reproducibility), or accuracy (relative errors in the range of 80–109%). The FDA-validated method was successfully applied to the analysis of triptorelin in the commercial drug Diphereline® 0.1 mg (powder for injection) and in spiked human plasma samples. Favorable performance parameters along with proven application potentialities indicate the usefulness of the proposed method for its routine use in drug quality control laboratories and for clinical analysis, such as determination of triptorelin levels in plasma (for pharmacokinetic study).

Improving the sensitivity in chiral capillary electrophoresis.

CE is known for being one of the most powerful analytical techniques when performing enantioseparations due to its numerous advantages such as excellent separation efficiency and extremely low solvents and reagents consumption, all of them derived from the capillary small dimensions. Moreover, it is worth highlighting that unlike in chromatographic techniques, in CE the chiral selector is generally within the separation medium instead of being attached to the separation column which makes the method optimization a more versatile task. Despite its numerous advantages, when using UV-Vis detection, CE lacks of sensitivity detection due to its short optical path length derived from the narrow separation capillary. This issue can be overcome by means of different approaches, either by sample treatment procedures or by in-capillary preconcentration techniques or even by employing detection systems more sensitive than UV-Vis, such as LIF or MS. The present review assembles the latest contributions regarding improvements of sensitivity in chiral CE published from June 2013 until May 2015, which follows the works included in a previous review reported by Sánchez-Hernández etal. [Electrophoresis 2014, 35, 12-27].

Detection of S-adenosylhomocysteine and methylation index in blood by capillary electrophoresis.

This work proposes an approach to the direct analysis of S-adenosylhomocysteine (SAH) and the methylation index in blood using CE with UV detection (CE-UV). After application of meglumine postinjection, we achieved SAH in-capillary preconcentration in the HClO4 extracts of erythrocytes, which improved the detection limit (S/N = 3) of SAH up to 3 fmol or 180 nmol/L at the injection volume of 50 nL, taking into account the sample dilution rate. CE-UV was carried out in 30 mM glycine and 45 mmol/L HCl (pH ~1.8) at 17 kV in a capillary 48 cm in length and 50 μm id. Accuracy of the technique was 101% and reproducibility was about 12%.

In-Capillary Derivatization and Preconcentration for CE of Metal Ions as Their Phenanthroline Complexes

A simple and automated method involving in-capillary derivatization and in-capillary preconcentration was developed for the simultaneous determination of metal ions by capillary zone electrophoresis. Fe(II), Zn(II), Cu(II) and Cd(II) were derivatized using 1,10-phenanthroline as the derivatizing agent. The in-capillary derivatization and in-capillary preconcentration via large volume injection were performed sequentially as follows: 60 mmol L−1 1,10-phenanthroline was first hydrodynamically injected (0.2 psi) for 2 s; metal ions were introduced by hydrodynamic injection (0.5 psi) for 60 s; 0.2 mol L−1 acetate pH 5.5 containing 20 % methanol was used as the running buffer. Four metal ions can be determined within 8 min using 16 kV. The resulting preconcentration factors were in the range 12–21. Good linearity was obtained for concentrations of 0.1–8.0 mg L−1 (r2 > 0.990). The mean recoveries of the metal ions evaluated by fortification of wine samples were in the range 90–102 %. The limits of detection ranged from 0.05 to 0.2 mg L−1. The proposed method can be applied for directly determining metal ions in wine samples.

Solid phase extraction of penicillins from milk by using sacrificial silica beads as a support for a molecular imprint

We have prepared molecularly imprinted beads with molecular recognition capability for target molecules containing the penicillanic acid substructure. They were prepared by (a) grafting mesoporous silica beads with 6-aminopenicillanic acid as the mimic template, (b) filling the pores with a polymerized mixture of methacrylic acid and trimethylolpropane trimethacrylate, and (c) removing the silica support with ammonium fluoride. The resulting imprinted beads showed good molecular recognition capability for various penicillanic species, while antibiotics such as cephalosporins or chloramphenicol were poorly recognized. The imprinted beads were used to extract penicillin V, nafcillin, oxacillin, cloxacillin and dicloxacillin from skimmed and deproteinized milk in the concentration range of 5–100 μg·L−1. The extracts were then analyzed by micellar electrokinetic chromatography by applying reverse polarity staking as an in-capillary preconcentration step, and this resulted in a fast and affordable method within the MRL levels, characterized by minimal pretreatment steps and recoveries of 64–90 %.

Improvement of the sensitivity of 2D LC‐MEKC separation of phenolic acids and flavonoids natural antioxidants using the on‐line preconcentration step

A 2D method was developed for separation of phenolic acids and flavonoids natural antioxidants combining LC with MEKC. The in-capillary preconcentration step was applied for the improvement of the sensitivity of 2D method before the second dimension MEKC analysis. The influence of first dimension LC mobile phase composition on migration times in the second MEKC dimension was evaluated. When gradient elution is applied in the first dimension of 2D LC-MEKC system, increasing concentration of organic solvent in the mobile phase and in fractions transferred from LC influences the electroosmotic flow, partitioning equilibria of samples in micelles and properties of the micelles, which results in shifts of migration times during the consecutive runs in the second MEKC separation dimension. The shifts of migration times caused by the influence of increasing concentration of ACN on MEKC separation in second dimension of 2D LC-MEKC system were compensated by aligning the time axis using electroosmotic flow and micellar marker migration times. The optimized LC-MEKC method was applied on the separation of natural antioxidants in the plant extracts samples.

Enhancing the Coverage of the Urinary Metabolome by Sheathless Capillary Electrophoresis-Mass Spectrometry

Sheathless capillary electrophoresis-mass spectrometry (CE-MS), using a porous tip sprayer, is proposed for the first time for highly sensitive metabolic profiling of human urine. A representative metabolite mixture and human urine were used for evaluation of the sheathless CE-MS platform. For test compounds, relative standard deviations (RSDs) for migration times and peak areas were below 2% and 12%, respectively, and an injection volume of only ∼8 nL resulted in detection limits between 11 and 120 nM. Approximately 900 molecular features were detected in human urine by sheathless CE-MS whereas about 300 molecular features were found with classical sheath-liquid CE-MS. This difference can probably be attributed to an improved ionization efficiency and increased sensitivity at low flow-rate conditions. The integration of transient-isotachophoresis (t-ITP) as an in-capillary preconcentration procedure in sheathless CE-MS further resulted in subnanomolar limits of detection for compounds of the metabolite mixture, and more than 1300 molecular features were observed in urine. Compared to the classical CE-MS approaches, the integration of t-ITP combined with the use of a sheathless interface provides up to 2 orders of magnitude sensitivity improvement. Hence, sheathless CE-MS can be used for in-depth metabolic profiling of biological samples, and we anticipate that this approach will yield unique information in the field of metabolomics.

Chiral separation of metalaxyl and benalaxyl fungicides by electrokinetic chromatography and determination of enantiomeric impurities

The enantiomers of two acylamine fungicides (metalaxyl and benalaxyl) were separated by EKC using CDs as chiral selectors. The use of 15 mM succinyl-γ-CD for metalaxyl and 5 mM succinyl-β-CD for benalaxyl dissolved in a 50 mM 2-morpholinoethanesulfonic acid buffer (pH 6.5), enabled the chiral separation of metalaxyl enantiomers in 11.5 min with a resolution of 3.1 and the enantiomeric separation of benalaxyl in 7.5 min with a resolution close to 15. Under these conditions, the two enantiomers of each of the chiral compound studied were also separated from folpet, very commonly present in fungicide formulations containing metalaxyl or benalaxyl. The analytical characteristics of the two developed methods were studied in terms of precision, linearity, selectivity, limits of detection (LODs) and limits of quantitation (LOQs) showing their suitability for the determination of these compounds in commercial agrochemical formulations. Finally, the development of an in-capillary preconcentration strategy allowed the detection of enantiomeric impurities up to 1.2% in commercial products labeled as enantiomerically pure in metalaxyl-M.

CE-MS for Metabolic Profiling of Volume-Limited Urine Samples: Application to Accelerated Aging TTD Mice

Metabolic profiling of biological samples is increasingly used to obtain more insight into the pathophysiology of diseases. For translational studies, biological samples from animal models are explored; however, the volume of these samples can be a limiting factor for metabolic profiling studies. For instance, only a few microliters of urine is often available from small animals like mice. Hence, there is a need for a tailor-made analytical method for metabolic profiling of volume-limited samples. In the present study, the feasibility of capillary electrophoresis time-of-flight mass spectrometry (CE-ToF-MS) for metabolic profiling of urine from mice is evaluated. Special attention is paid to the analytical workflow; that is, such aspects as sample preparation, analysis, and data treatment are discussed from the metabolomics viewpoint. We show that metabolites belonging to several chemical families can be analyzed in mouse urine with the CE-ToF-MS method using minimal sample pretreatment and an in-capillary preconcentration procedure. This exemplifies the advantages of CE-ToF-MS for metabolic profiling of volume-limited samples as loss of material is minimized. The feasibility of the CE-ToF-MS-based workflow for metabolic profiling is illustrated by the analysis of urine samples from wild-type as well as from TTD mutant mice, which are a model for the accelerated aging, with osteoporosis being one of the main hallmarks.

Separation of proteins from olive oil by CE: An approximation to the differentiation of monovarietal olive oils

The separation of proteins from olive oils by CE has been achieved for the first time in this work. Based on the protein profiles obtained using UV detection, a novel approach has also been proposed enabling the differentiation of monovarietal olive oils. An extraction procedure based on the precipitation of proteins in cold acetone and their isolation and solubilization in a hydro-organic medium prior to their in-capillary preconcentration in CE was a critical step in method development since proteins are minor components of olive oils. Then, a CE separation using a basic medium in a dynamically coated capillary originated electrophoretic profiles with multiple peaks from which seven of them were identified as proteins. When different monovarietal olive oils were injected, three different regions (zones I, II, and III) were identified. Zone III, called as differential zone, enabled to distinguish easily between extra virgin olive oils made from the Arbequina variety and the Picual and Hojiblanca varieties. This is the first time that protein profiles have been employed for the differentiation of botanical varieties of olive oils showing an enormous potential as traceability markers for these highly appreciated oils.

In‐capillary microextraction using monolithic polymers: Application to preconcentration of carbamate pesticides prior to their separation by MEKC

In the present work we report a novel procedure for in-capillary microextraction using a monolithic polymeric sorbent. In the proposed methodology, sample treatment takes place in the CE instrument but in a different capillary from that used for the electrophoretic separation. Polymers based on butyl methacrylate and divinylbenzene formed in situ inside a capillary column were assayed. The best results were found with the divinylbenzene-based polymers. The usefulness of the proposed procedure was checked for the determination of carbamate pesticides (Methomyl, Asulam, Carbendazim, Aldicarb, Carbetamide, Propoxur, Pirimicarb, Carbaryl, Carbofuran and Methiocarb) and three of their degradation compounds (Aldicarb sulphoxide, 2-isopropoxyphenol and alpha-naphthol) using MEKC. The optimization of the MEKC is reported, a good separation of the 13 analytes being obtained in less than 6 min. The analytical method using in-capillary microextraction was validated in terms of linearity, repeatability, precision (RSD< or =18% for 50 microg/L), and LODs (1-16 microg/L), and it revealed the usefulness of this in-capillary preconcentration procedure for the determination of analytes of intermediate polarity.

Capillary electrophoresis‐time of flight‐mass spectrometry using noncovalently bilayer‐coated capillaries for the analysis of amino acids in human urine

A capillary electrophoresis-time of flight-mass spectrometry (CE-TOF-MS) method for the analysis of amino acids in human urine was developed. Capillaries noncovalently coated with a bilayer of Polybrene (PB) and poly(vinyl sulfonate) (PVS) provided a considerable EOF at low pH, thus facilitating the fast separation of amino acids using a BGE of 1 M formic acid (pH 1.8). The PB-PVS coating proved to be very consistent yielding stable CE-MS patterns of amino acids in urine with favorable migration time repeatability (RSDs <2%). The relatively low sample loading capacity of CE was circumvented by an in-capillary preconcentration step based on pH-mediated stacking allowing 100-nL sample injection (i.e. ca. 4% of capillary volume). As a result, LODs for amino acids were down to 20 nM while achieving satisfactory separation efficiencies. Preliminary validation of the method with urine samples showed good linear responses for the amino acids (R(2) >0.99), and RSDs for peak areas were <10%. Special attention was paid to the influence of matrix effects on the quantification of amino acids. The magnitude of ion suppression by the matrix was similar for different urine samples. The CE-TOF-MS method was used for the analysis of urine samples of patients with urinary tract infection (UTI). Concentrations of a subset of amino acids were determined and compared with concentrations in urine of healthy controls. Furthermore, partial least squares-discriminant analysis (PLS-DA) of the CE-TOF-MS dataset in the 50-450 m/z region showed a distinctive grouping of the UTI samples and the control samples. Examination of score and loadings plot revealed a number of compounds, including phenylalanine, to be responsible for grouping of the samples. Thus, the CE-TOF-MS method shows good potential for the screening of body fluids based on the analysis of endogenous low-molecular weight metabolites such as amino acids and related compounds.

Development of Novel In-Capillary Preconcentration Methods for Capillary Electrophoresis

Development of Novel In-Capillary Preconcentration Methods for Capillary Electrophoresis

Sensitive chiral analysis by CE: An update

A general view of the different strategies used in the last years to enhance the detection sensitivity in chiral analysis by CE is provided in this article. With this purpose and in order to update the previous review by García-Ruiz et al., the articles appeared on this subject from January 2005 to March 2007 are considered. Three were the main strategies employed to increase the detection sensitivity in chiral analysis by CE: (i) the use of off-line sample treatment techniques, (ii) the employment of in-capillary preconcentration techniques based on electrophoretic principles, and (iii) the use of alternative detection systems to the widely employed on-column UV-Vis absorption detection. Combinations of two or three of the above-mentioned strategies gave rise to adequate concentration detection limits up to 10(-10) M enabling enantiomer analysis in a variety of real samples including complex biological matrices.

Contribution of hyphenated CE-ICP/MS in metal/protein interactions studies

Summary By introducing a preliminary in-capillary preconcentration step, CE-ICP/MS was applied to trace metal speciation in proteins. Emphasis was put on metal/protein interactions where CE-ICP/MS is demonstrated to provide informations concerning metal binding and metal exchanges occuring in proteins. Preliminary studies on the fate of several metals in the presence of a mixture of standard proteins were performed. Cadmium was shown to bind mainly to albumin and ceruloplasmin. Cobalt and nickel were detected only in carbonic anhydrase and ceruloplasmin in the mixture of proteins but also in albumin when injected alone.

In-capillary preconcentration of proteins for capillary electrophoresis using a cellulose acetate-coated porous joint

This work describes the in-capillary preconcentration of proteins using a cellulose acetate-coated porous joint. The capillary wall near the inlet end of a capillary was made porous by HF etching. During the etching process, a voltage was applied across the capillary wall and the electric current across it was monitored. As the current passed through the capillary wall, it became porous. A solution of cellulose acetate in acetone was added to the etched porous joint. After the acetone was evaporated off, a cellulose acetate-coated porous joint was formed. To preconcentrate the protein ions, an electric voltage was applied between the inlet end of the capillary and the coated porous joint; the protein ions electromigrated to the porous joint but could not pass through it, while the buffer ions could pass easily through the joint. After allowing a certain amount of time for protein preconcentration, a separation voltage was applied across the two ends of the capillary, and normal capillary electrophoresis was carried out. The preconcentration factors for cytochrome c, lysozyme, ribonuclease, and chymotrypsinogen were 65, 155, 705, and 800, respectively. The cellulose acetate-coated porous joint was shown to be strong and stable over time, and was used to analyze trace proteins and macromolecules in biological samples.

Analysis of serotonin in brain microdialysates using capillary electrophoresis and native laser-induced fluorescence detection

Serotonin or 5-hydroxytryptamine (5-HT) is a major neurotransmitter in the central nervous system. In this work, a method for analyzing 5-HT in brain microdialysis samples using a commercially available capillary electrophoresis (CE) system has been developed. A pH-mediated in-capillary preconcentration of samples was performed, and after separation by capillary zone electrophoresis, native fluorescence of 5-HT was detected by a 266 nm solid-state laser. The separation conditions for the analysis of 5-HT in standard solutions and microdialysates have been optimized, and this method has been validated on both pharmacological and analytical bases. Separation of 5-HT was performed using a 80 mmol/L citrate buffer, pH 2.5, containing 20 mmol/L hydroxypropyl-beta-cyclodextrin (HP-beta-CD) and +30 kV voltage. The detection limit was 2.5 x 10(-10) mol/L. This method allows the in vivo brain monitoring of 5-HT using a simple, accurate CE measurement in underivatized microdialysis samples.