Improvement In Detective Quantum Efficiency Research Articles

Next generation high resolution perovskite direct conversion detector: Monte Carlo design optimisation and virtual clinical trial

We implement virtual clinical integration of next-generation perovskite detectors into common x-ray imaging devices. This was achieved by performing Monte Carlo (MC) optimisation of the design and benchmarking of low cost, high spatial resolution, direct conversion perovskite crystal x-ray flat panel imagers for a next generation of breast-, MV-, and kV-cone beam CT detectors. Semiconductor methylammonium lead bromide perovskite crystals energy deposition efficiencies calculated in TOPAS were benchmarked against four common detector materials for twelve detector crystal thicknesses between 40 to 15 mm and ten beam energies ranging from 20 keV to 6 MeV. Based on these simulations, Koning's dedicated breast CT, and Varian's Truebeam kV- and MV-cone beam CT systems were designated as suitable applications for perovskite detectors. System specific Fastcat hybrid MC cone beam CT image simulation was subsequently used to optimise the perovskite detector design and conduct virtual clinical trials. Device-specific optimal perovskite crystal thicknesses were calculated to be 0.30, 0.86, and 1.99 mm for Koning breast CT and Truebeam kV- and MV-cone beam CT systems, respectively. Replacing the current detectors on these machines with low cost perovskite crystal detectors could be advantageous as it would simultaneously yield 12.1%, 9.5% and 86.1% improvements in detective quantum efficiency as well as increases in contrast to noise ratio in brain, lung, and bone tissues.

Experimental characterization of a direct conversion amorphous selenium detector with thicker conversion layer for dual-energy contrast-enhanced breast imaging.

Dual-energy contrast-enhanced imaging is being investigated as a tool to identify and localize angiogenesis in the breast, a possible indicator of malignant tumors. This imaging technique requires that x-ray images are acquired at energies above the k-shell binding energy of an appropriate radiocontrast agent. Iodinated contrast agents are commonly used for vascular imaging, and require x-ray energies greater than 33 keV. Conventional direct conversion amorphous selenium (a-Se) flat-panel imagers for digital mammography show suboptimal absorption efficiencies at these higher energies. We use spatial-frequency domain image quality metrics to evaluate the performance of a prototype direct conversion flat-panel imager with a thicker a-Se layer, specifically fabricated for dual-energy contrast-enhanced breast imaging. Imaging performance was evaluated in a prototype digital breast tomosynthesis (DBT) system. The spatial resolution, noise characteristics, detective quantum efficiency, and temporal performance of the detector were evaluated for dual-energy imaging for both conventional full-field digital mammography (FFDM) and DBT. The zero-frequency detective quantum efficiency of the prototype detector is improved by approximately 20% over the conventional detector for higher energy beams required for imaging with iodinated contrast agents. The effect of oblique entry of x-rays on spatial resolution does increase with increasing photoconductor thickness, specifically for the most oblique views of a DBT scan. Degradation of spatial resolution due to focal spot motion was also observed. Temporal performance was found to be comparable to conventional mammographic detectors. Increasing the a-Se thickness in direct conversion flat-panel imagers results in better performance for dual-energy contrast-enhanced breast imaging. The reduction in spatial resolution due to oblique entry of x-rays is appreciable in the most extreme clinically relevant cases, but may not profoundly affect reconstructed images due to the algorithms and filters employed. Degradation to projection domain spatial resolution is thus outweighed by the improvement in detective quantum efficiency for high-energy x-rays.

Single-particle cryo-EM data acquisition by using direct electron detection camera.

Recent advances in single-particle electron cryo-microscopy (cryo-EM) were largely facilitated by the application of direct electron detection cameras. These cameras feature not only a significant improvement in detective quantum efficiency but also a high frame rate that enables images to be acquired as 'movies' made of stacks of many frames. In this review, we discuss how the applications of direct electron detection cameras in cryo-EM have changed the way the data are acquired.

Cascaded systems analysis of photon counting detectors.

Photon counting detectors (PCDs) are an emerging technology with applications in spectral and low-dose radiographic and tomographic imaging. This paper develops an analytical model of PCD imaging performance, including the system gain, modulation transfer function (MTF), noise-power spectrum (NPS), and detective quantum efficiency (DQE). A cascaded systems analysis model describing the propagation of quanta through the imaging chain was developed. The model was validated in comparison to the physical performance of a silicon-strip PCD implemented on an experimental imaging bench. The signal response, MTF, and NPS were measured and compared to theory as a function of exposure conditions (70 kVp, 1-7 mA), detector threshold, and readout mode (i.e., the option for coincidence detection). The model sheds new light on the dependence of spatial resolution, charge sharing, and additive noise effects on threshold selection and was used to investigate the factors governing PCD performance, including the fundamental advantages and limitations of PCDs in comparison to energy-integrating detectors (EIDs) in the linear regime for which pulse pileup can be ignored. The detector exhibited highly linear mean signal response across the system operating range and agreed well with theoretical prediction, as did the system MTF and NPS. The DQE analyzed as a function of kilovolt (peak), exposure, detector threshold, and readout mode revealed important considerations for system optimization. The model also demonstrated the important implications of false counts from both additive electronic noise and charge sharing and highlighted the system design and operational parameters that most affect detector performance in the presence of such factors: for example, increasing the detector threshold from 0 to 100 (arbitrary units of pulse height threshold roughly equivalent to 0.5 and 6 keV energy threshold, respectively), increased the f50 (spatial-frequency at which the MTF falls to a value of 0.50) by ∼30% with corresponding improvement in DQE. The range in exposure and additive noise for which PCDs yield intrinsically higher DQE was quantified, showing performance advantages under conditions of very low-dose, high additive noise, and high fidelity rejection of coincident photons. The model for PCD signal and noise performance agreed with measurements of detector signal, MTF, and NPS and provided a useful basis for understanding complex dependencies in PCD imaging performance and the potential advantages (and disadvantages) in comparison to EIDs as well as an important guide to task-based optimization in developing new PCD imaging systems.

Optimization of the design of thick, segmented scintillators for megavoltage cone-beam CT using a novel, hybrid modeling technique.

Active matrix flat-panel imagers (AMFPIs) incorporating thick, segmented scintillators have demonstrated order-of-magnitude improvements in detective quantum efficiency (DQE) at radiotherapy energies compared to systems based on conventional phosphor screens. Such improved DQE values facilitate megavoltage cone-beam CT (MV CBCT) imaging at clinically practical doses. However, the MV CBCT performance of such AMFPIs is highly dependent on the design parameters of the scintillators. In this paper, optimization of the design of segmented scintillators was explored using a hybrid modeling technique which encompasses both radiation and optical effects. Imaging performance in terms of the contrast-to-noise ratio (CNR) and spatial resolution of various hypothetical scintillator designs was examined through a hybrid technique involving Monte Carlo simulation of radiation transport in combination with simulation of optical gain distributions and optical point spread functions. The optical simulations employed optical parameters extracted from a best fit to measurement results reported in a previous investigation of a 1.13 cm thick, 1016 μm pitch prototype BGO segmented scintillator. All hypothetical designs employed BGO material with a thickness and element-to-element pitch ranging from 0.5 to 6 cm and from 0.508 to 1.524 mm, respectively. In the CNR study, for each design, full tomographic scans of a contrast phantom incorporating various soft-tissue inserts were simulated at a total dose of 4 cGy. Theoretical values for contrast, noise, and CNR were found to be in close agreement with empirical results from the BGO prototype, strongly supporting the validity of the modeling technique. CNR and spatial resolution for the various scintillator designs demonstrate complex behavior as scintillator thickness and element pitch are varied--with a clear trade-off between these two imaging metrics up to a thickness of ~3 cm. Based on these results, an optimization map indicating the regions of design that provide a balance between these metrics was obtained. The map shows that, for a given set of optical parameters, scintillator thickness and pixel pitch can be judiciously chosen to maximize performance without resorting to thicker, more costly scintillators. Modeling radiation and optical effects in thick, segmented scintillators through use of a hybrid technique can provide a practical way to gain insight as to how to optimize the performance of such devices in radiotherapy imaging. Assisted by such modeling, the development of practical designs should greatly facilitate low-dose, soft tissue visualization employing MV CBCT imaging in external beam radiotherapy.

SU‐D‐301‐01: Performance Limits of Large Area Poly‐Si X‐Ray Imagers Employing In‐Pixel Amplification

Purpose: Active matrix flat‐panel imagers (AMFPIs) — based on amorphous silicon thin‐film transistors (TFTs) — have been developed for a wide variety of x‐ray imaging applications at diagnostic energies. However, under conditions of low exposure or small pixel sizes, the additive electronic noise associated with readout of the pixel signal of these imagers leads to relatively low levels of signal‐to‐noise ratio — resulting in significant loss of detective quantum efficiency (DQE) and image quality. An increasingly promising approach for overcoming such limitations involves the incorporation of in‐pixel amplification circuits, referred to as active pixel (AP) architectures, based on low‐temperature polycrystalline silicon (poly‐ Si) TFTs. Methods: Theoretical performance limits for additive noise and DQE for large area imagers employing various AP designs have been explored. The methodology involves SPICE simulations of pixel circuits in an array environment employing realistic inputs for signal, as well as noise derived from individual poly‐Si TFT test devices. Pixel circuit noise performance derived from these simulations, along with other imaging parameters, are input to cascaded systems models for calculations of the corresponding DQE performance. Results: For large area imagers employing architectures comprising one‐ and two‐stage in‐pixel amplification, the calculations suggest that the effect of additive noise can be significantly diminished, leading to substantial improvement in DQE compared to that of conventional AMFPIs, especially at the low exposures associated with fluoroscopy. Such improved performance is largely maintained even for more sophisticated pixel designs incorporating additional features such as higher frame rate and selectable amplification gain. Conclusions: Active pixel imagers based on poly‐Si TFTs offer a potential alternative to conventional AMFPIs for overcoming the decline of DQE at low exposures in fluoroscopy. The combination of detailed circuit simulations and cascaded systems modeling provides a powerful tool for guiding the development of future generations of ever more sophisticated imagers.Work Supported by NIH grant R01‐EB000558

High-DQE EPIDs based on thick, segmented BGO and CsI:Tl scintillators: performance evaluation at extremely low dose.

Electronic portal imaging devices (EPIDs) based on active matrix, flat-panel imagers (AMFPIs) have become the gold standard for portal imaging and are currently being investigated for megavoltage cone-beam computed tomography (CBCT) and cone-beam digital tomosynthesis (CBDT). However, the practical realization of such volumetric imaging techniques is constrained by the relatively low detective quantum efficiency (DQE) of AMFPI-based EPIDs at radiotherapy energies, approximately 1% at 6 MV. In order to significantly improve DQE, the authors are investigating thick, segmented scintillators, consisting of 2D matrices of scintillating crystals separated by septal walls. A newly constructed segmented BGO scintillator (11.3 mm thick) and three segmented CsI:Tl scintillators (11.4, 25.6, and 40.0 mm thick) were evaluated using a 6 MV photon beam. X-ray sensitivity, modulation transfer function, noise power spectrum, DQE, and phantom images were obtained using prototype EPIDs based on the four scintillators. The BGO and CsI:Tl prototypes were found to exhibit improvement in DQE ranging from approximately 12 to 25 times that of a conventional AMFPI-based EPID at zero spatial frequency. All four prototype EPIDs provide significantly improved contrast resolution at extremely low doses, extending down to a single beam pulse. In particular, the BGO prototype provides contrast resolution comparable to that of the conventional EPID, but at 20 times less dose, with spatial resolution sufficient for identifying the boundaries of low-contrast objects. For this prototype, however, the BGO scintillator exhibited an undesirable radiation-induced variation in x-ray sensitivity. Prototype EPIDs based on thick, segmented BGO and CsI:T1 scintillators provide significantly improved portal imaging performance at extremely low dose (i.e., down to 1 beam pulse corresponding to approximately 0.022 cGy), creating the possibility of soft-tissue visualization using MV CBCT and CBDT at clinically practical dose.

Characterization of noise sources for two generations of computed radiography systems using powder and crystalline photostimulable phosphors

The performances of two generations of computed radiography (CR) were tested and compared in terms of resolution and noise characteristics. The main aim was to characterize and quantify the noise sources in the images. The systems tested were (1) Agfa CR 25.0, a flying spot reader with powder phosphor image plates (MD 40.0); and (2) the Agfa DX-S, a line-scanning CR reader with needle crystal phosphor image plates (HD 5.0). For both systems, the standard metrics of presampled modulation transfer function (MTF), normalized noise power spectra (NNPS) and detective quantum efficiency (DQE) were measured using standard radiation quality RQA5 as defined by the International Electrotechnical Commission. The various noise sources contributing to the NNPS were separated by using knowledge of their relationship with air kerma, MTF, absorption efficiency and antialiasing filters. The DX-S MTF was superior compared with the CR 25.0. The maximum difference in MTF between the DX-S scan and CR 25.0 subscan directions was 0.13 at 1.3 mm(-1). For a nominal detector air kerma of 4 microGy, the peak DQE of the DX-S was 43 (+/-3)%, which was over double that of the CR 25.0 of 18 (+/-2)%. The additive electronic noise was negligible on the CR 25.0 but calculated to be constant 3.4 x 10(-7) (+/-0.4 x 10(-7)) mm2 at 3.9 microGy on the DX-S. The DX-S has improved image quality compared with a traditional flying spot reader. The separation of the noise sources indicates that the improvements in DQE of the DX-S are due not only to the higher quantum, efficiency and MTF, but also the lower structure, secondary quantum, and excess noise.

A comparison of x-ray detectors for mouse CT imaging

There is significant interest in using computed tomography (CT) for in vivo imaging applications in mouse models of disease. Most commercially available mouse x-ray CT scanners utilize a charge-coupled device (CCD) detector coupled via fibre optic taper to a phosphor screen. However, there has been little research to determine if this is the optimum detector for the specific task of in vivo mouse imaging. To investigate this issue, we have evaluated four detectors, including an amorphous selenium (a-Se) detector, an amorphous silicon (a-Si) detector with a gadolinium oxysulphide (GOS) screen, a CCD with a 3:1 fibre taper and a GOS screen, and a CCD with a 2:1 fibre taper and both GOS and thallium-doped caesium iodide (CsI:Tl) screens. The detectors were evaluated by measuring the modulation transfer function (MTF), noise power spectrum (NPS), detective quantum efficiency (DQE), stability over multiple exposures, and noise in reconstructed CT images. The a-Se detector had the best MTF and the highest DQE (0.6 at 0 lp mm−1) but had the worst stability (45% reduction after 2000 exposure frames). The a-Si detector and the CCD with the 3:1 fibre, both of which used the GOS screen, had very similar performance with a DQE of approximately 0.30 at 0 lp mm−1. For the CCD with the 2:1 fibre, the CsI:Tl screen resulted in a nearly two-fold improvement in DQE over the GOS screen (0.4 versus 0.24 at 0 lp mm−1). The CCDs both had the best stability, with less than a 1% change in pixel values over multiple exposures. The pixel values of the a-Si detector increased 5% over multiple exposures due to the effects of image lag. Despite the higher DQE of the a-Se detector, the reconstructed CT images acquired with the a-Si detector had lower noise levels, likely due to the blurring effects from the phosphor screen.

Detective quantum efficiency dependence on x-ray energy weighting in mammography.

An evaluation of the dependence of detective quantum efficiency (DQE) on the incident energy spectrum has been made for mammography. The DQE dependence on the energy spectrum has been evaluated for energy-integrating detectors, photon-counting detectors, and detectors that measure the energy of each photon. To isolate the effect of the x-ray energy spectrum the detector has been assumed to be ideal, i.e., all noise sources are assumed to be zero except for quantum fluctuations. The result shows that the improvement in DQE, if the energy-integrating detector is compared to a single-photon counting detector, is of the order of 10%. Comparing the energy-integrating detector and the detector measuring the energy for each photon the improvement is around 30% using a molybdenum anode spectrum typical in mammography. It is shown that the optimal weight factors to combine the data in the case the energy is measured are very well approximated if the weight factors are proportional to E(-3). Another conclusion is that in calculating the DQE, a detector should be compared to one that uses ideal energy weighting for each photon since this provides the best signal-to-noise ratio. This has generally been neglected in the literature.

Initial performance evaluation of an indirect-detection, active matrix flat-panel imager (AMFPI) prototype for megavoltage imaging

Purpose: The development of the first prototype active matrix flat-panel imager (AMFPI) capable of radiographic and fluoroscopic megavoltage operation is reported. The signal and noise performance of individual pixels is empirically quantified. Results of an observer-dependent study of imaging performance, using a contrast-detail phantom, are detailed and radiographic patient images are shown. Finally, a theoretical investigation of the zero-frequency detective quantum efficiency (DQE) performance of such imagers, using a cascaded systems formalism, is presented.Methods and Materials: The imager is based on a 508-μm pitch, 26 × 26 cm2 array which detects radiation indirectly via an overlying copper plate + phosphor screen converter.Results: Due to its excellent optical coupling, the imager exhibits sensitivity superior to that of video-based systems. With an ∼133 mg/cm2 Gd2O2S:Tb screen the system is x-ray quantum-noise-limited down to ∼0.3 cGy, conservatively, and extensions of this behavior to even lower doses by means of reduced additive electronic noise is predicted. The observer-dependent study indicates performance superior to that of conventional radiotherapy film while the patient images demonstrate good image quality at 1 to 4 MU. The theoretical studies suggest that, with a 133 mg/cm2 Gd2O2S:Tb screen, the system would provide DQE performance equivalent to that of video-based systems and that almost a factor of two improvement in DQE is achievable through the incorporation of a 400 mg/cm2 screen.Conclusion: The reported prototype imager is the first megavoltage AMFPI having performance characteristics consistent with practical clinical operation. The superior contrast-detail sensitivity of the imager allows the capture of high-quality 6- and 15-MV images at minimal dose. Moreover, significant performance improvements, including extension of the operational range up to full portal doses, appear feasible. Such capabilities could be of considerable practical benefit in patient localization and verification.

高量子検出効率イメージインテンシファイアの画質評価

A new X-ray image intensifier(Toshiba J-type I.I.)has been developed in response to the digital X-ray image requirements of recent diagnostic systems. In the J-type I.I., the input phosphor screen(450-μm thick, CsI)has been deposited directly on the input window. Since there is no space between the input window and phosphor screen, the scattering of X-rays at the input window is reduced. Consequently, the X-ray detection efficiency over a wide range of X-ray tube operating voltages is also improved. Our studies have shown that the 10-mm contrast ratio is 24(for a 9 inch I.I.). Using International Electrotechnical Commission(IEC)Standard methods, we have concluded that the detective quantum efficiency(DQE)is 70%. We have also compared the characteristics of the J-type I.I.with those of the conventional G-type I.I. using the DFP-2000A DF system(TOSHIBA). The main results are enumerated below. (1)The veiling-glare fraction(VGF)was about 5% less for the J-type I.I. (2)The resolution quality was the same for both types of I.I. (3)Noise was less for the J-type I.I.because of the improvement in DQE. (4)The signal to noise ratio was higher for the J-type I.I.because of the reduction of noise. (5)Receiver operating characteristic(ROS)analysis showed that signal detectability was better for the J-type I.I.

The Influence of Grain Sensitivity on Photographic Image Properties

AbstractThe statistical distribution of quantum sensitivities of photographic grains plays an important role in defining the input/output relationships of the photographic process. This role is investigated from the aspect of the characteristic curve and detective quantum efficiency. A simple analogy between latent image formation and a random quantum loss process leads to a two-parameter theoretical sensitivity distribution which can explain the observed invariance of curve shape with sensitization. This a.llows a direct relationship between sensitivity a.nd detective quantum efficiency to be formulated. The limits for further sensitivity-type improvements in detective quantum efficiency without loss of latitude can then be established.