Hygroscopic Materials Research Articles

Vegetables Treated before Drying with Natural Antioxidants plus UV-C Improve Colour and Bioactive Compounds

The quality of minimally processed fruits and vegetables is essential for consumers’ health and effective marketing. This study investigates the effects of UV-C irradiation, applied alone and combined with various natural antioxidants, on the preservation of bioactive compounds and the colour of dehydrated fruits and vegetables. To achieve this, red peppers, yellow peppers, tomatoes, zucchini, eggplants, and melons were subjected to pre-treatments with natural antioxidants and UV-C before processing using low-temperature airflow (50 °C). The drying kinetics showed typical curves of hygroscopic materials, while the drying time was high due to the low temperature applied. The higher drying rate was found for eggplant, due to its porosity, thus allowing a faster moisture removal. The application of antioxidants and UV-C treatments effectively preserved the colour parameters L*, a*, and b*, while in the case of untreated dried vegetables, a significant worsening of colour parameters was noted. However, most applied pre-treatments had positive effects on bioactive compound losses. The best results were obtained using a combination of UV-C with one antioxidant mix that was composed of vanillin, rosemary, and citrus extracts, and combined with a mixture of olive, onion, garlic, and citric acid extracts, which was highly effective in preserving the colour and bioactive compounds of most dried vegetables.

Hygroscopic salt-embedded composite materials for sorption-based atmospheric water harvesting

Hygroscopic salt-embedded composite materials for sorption-based atmospheric water harvesting

DRIED NATA DE COCO WITH WATER ABSORPTIVITY COMPETING SILICA GEL

Nata de Coco (NDC) is a network of cellulose fibers that traps abundant of water. If a freshly made NDC is dried to remove nearly all trapped water, we will get a very hygroscopic material. This material is potential for making water adsorber that might compete the well known silica gel. NDC was prepared using standard methods and its water absorption was investigated. Dried NDC was used in this study. For comparison, we also investigated the water absorption of several commercial NDC. To determine its business prospects, the water absorption of silica gel was also investigated. The results showed that dried NDC could absorb water vapor comparable to the absorption of commercial silica gel. This suggests that dry NDC has the potential as an alternative water vapor absorber in food packaging. The advantages of the NDC compared to silica gel are safer and environmentally benign, and easily decomposed.

Potential Water Collection From Air by Chloride Perovskites.

Directly capturing water from the air has become a compelling strategy to secure water resources. Yet, challenges persist with sorption-based hygroscopic materials, such as inadequate water adsorption efficiency, material degradation post-adsorption, and the need for energy input during water collection. This study introduces an alternative category of sorbent materials potentially for atmospheric water harvesting-metal chloride perovskites-that exhibit spontaneous water vapor adsorption and liquid water collection. This water uptake capability stems from the uncoordinated polar ions that form hydrogen bonds with water molecules, while the cubic lattice imparts a solid framework ensuring structural stability and inhibiting hydrolysis. The methylammonium lead chloride perovskite pellets exhibit efficient water collection performance, with a record absorption rate of 0.841 L m-2 h-1 and a total water collection of 3.675 L m-2 within a 7-h cycle. This initiative attempts to provide a new material class candidate for the potential application of passive atmospheric water harvesting.

Reconsidering Museums’ Climate and Seasonal Adjustment for Vulnerable Artifacts

ABSTRACT The paper provides new experimental evidence for vulnerable artifacts on the dependence of failure strain on the loading rate corresponding to typical environmental loads lasting between hours and months. Animal glue-based ground was chosen for this study as an easily available, hygroscopic and brittle material as well as due to its abundance in collections and its relevance when discussing the risk of mechanical damage to objects. Gesso specimens were tested using dynamic mechanical analysis and tensile testing at different frequencies, under a variety of loading rates and temperatures. The time-temperature superposition principle was used to predict the material response to slow deformations (lasting hours to months) that are otherwise inaccessible on laboratory timescales. The results demonstrate that brittle materials such as animal glue-based grounds do not benefit from longer cycles of applied loads as failure strain is not time-dependent within the investigated timescale.

Teor de água de equilíbrio: Uso de sensores de umidade relativa do ar intergranular em silos

ABSTRACT Grains are hygroscopic materials and, during storage, they are subject to exchanging moisture with the environment according to temperature and relative air humidity, making it important to monitor these factors. Digital temperature and relative air humidity sensors appear as an alternative for monitoring the moisture of grain mass inside silos; they are simple to install and use. Digital sensors present outstanding precision in temperature measurements. The objective in this study was to assess the efficiency and applicability of intergranular relative air humidity sensors linked to digital temperature sensors in the thermometry system of silos storing soybeans. Two samples of soybeans were analyzed in the upper, middle and lower thirds of the silo, for grain mass temperature, intergranular relative air humidity, estimated equilibrium moisture content according to collected data, and moisture content of the sampled grains. Moisture contents obtained from sensor measurements using the hygroscopic equilibrium equation and determined using the oven method were compared. The equilibrium moisture content estimated by the data provided by the sensors did not differ by the Tukey test (p ≤ 0.05) from the moisture content determined by the oven method. Digital temperature and relative air humidity sensors have proven to be efficient, as they contribute to estimating the equilibrium moisture content with satisfactory precision.

Closure to “Experimental and a dual-scale analysis of the influence of coating on humidity control ability of hygroscopic materials with different porosity”

This paper presents a response to the discussion of “Experimental and a dual-scale analysis of the influence of coating on humidity control ability of hygroscopic materials with different porosity”

Fungal Biodeterioration Risk in Monastic Libraries without Climate Control.

Fungi have always posed an unquestionable threat to heritage collections worldwide. Now, in a future of climate change, biological risk factors may have to be considered even more than before. Models and simulations to assess possible impacts a changing outdoor climate will have on indoor environments and, in turn, on biodeterioration are still underdeveloped and require a more substantial data basis. This study aimed at filling some of these knowledge gaps through a broad-based approach combining microclimatic and microbiological monitoring in four historic libraries in Austria with an uncontrolled indoor climate: Altenburg Abbey, Melk Abbey, Klosterneuburg Monastery and the Capuchin Monastery in Vienna. Data were generated from thermohygrometric sensors, cultivation-dependent air- and surface sampling and further surface dust sampling for cultivation-independent analyses. Results gave insights on the status quo of microbiological loads in the libraries and outdoor-indoor relationships. Influences of the geographic location and room-use on corresponding indoor fungal profiles were identified. Lower fungal diversities were found at the most rural site with the strongest climatic fluctuations and extreme values than in the most urban, sheltered library with a very stable climate. Further, the humidity-stabilizing potential of large collections of hygroscopic materials, such as books, was also examined. Implications for a sustainable approach to prevent future biodeterioration are discussed, supporting the long-term preservation of these valuable historic collections.

Preparation of Hollow Silica Nanoparticles with Polyacrylic Acid and Their Moisture Sorption Properties

Hollow silica nanoparticles (HSNPs) have hygroscopic properties because of their high specific surface area and surface hydroxyl groups. However, compared with other hygroscopic materials, their hygroscopic properties are relatively weak, which limits the further application of HSNPs. One feasible method to enhance their hygroscopic properties is by combining highly hygroscopic materials with hollow silica nanoparticles. To take advantage of the high hygroscopicity of polyacrylic acid (PAA) when combined with the high specific surface area of the hollow particles, PAA was coated on the inner and outer surfaces of the silica shell of the nanoparticles in this study to prepare hollow nanoparticles with a PAA/silica/PAA multilayer structure. The size of the PAA/silica/PAA multi-layer nanoparticles is about 85 nm, and the shell thickness is 25 nm. The specific surface area of the multi-layer nanoparticles is 58 m2/g. The water vapor adsorption capacity of multi-layer structure hollow nanoparticles was increased by 160% compared with the HSNPs (increased from 45.9 cm3/m2 to 109.1 cm3/m2). Meanwhile, at the same content of PAA, the PAA/silica/PAA-structured particles will adsorb 9% more water vapor than the PAA/silica-structured particles. This indicates that the high specific surface area structure of the hollow particles will enhance the adsorption ability of PAA toward water vapor. This novel structure of PAA-HSNPs is expected to be used as a humidity-regulating material for filler in environmental and architectural applications.

Yacon powder mix: Effects of the composition and the process of microencapsulation by spray drying

Yacon is a tuber known as a healthy food due to its effects as an antidiabetic, anti-inflammatory, anticancer, and prebiotic agent; it is rich in fructooligosaccharides (FOS) and antioxidants, and due to its sweet taste and low-calorie content, it is used as a substitute for ordinary sugar. This research aimed to evaluate the influence of the composition of the feed and the microencapsulation process by spray drying (SD) on the properties of a yacon powder mixture (YP). Response surface methodology with a central composite design with a face-centered composition (α = 1) was used, considering the independent variables: inulin (IN) (3–5% w/w), maltodextrin (MD) (3–5% w/w), air inlet temperature (AIT) (140–160 °C), air outlet temperature (AOT) (75–85 °C) and atomizer disc speed (ADS) (18000–22000 rpm), and the dependent variables: moisture (Xw), water activity (aw), hygroscopicity (Hy), solubility (S), particle size (percentile D10, D50, and D90), total phenols (TP), antioxidant capacity (ABTS and DPPH), color (CIE-Lab*) and yield (Yi). The suspension formulation contained xanthan gum (0.167 %) and a mixture of ascorbic and citric acids (0.3 %). The aw and Xw values of the YP guarantee its microbiological stability; however, the process formulation produces a complex matrix (FOS- sugars- MD - IN) with high affinity for water, which favors adsorption phenomena (hygroscopic material) and high reconstitution (high solubility). The independent variables that best fit the experimental optimization criteria were: IN = 3.0 %, MD = 5.0 %, AIT = 143.7 °C, AOT = 80.1 °C, ADS = 22000 rpm, where Yi = 84.2 %, and the quality of the YP: Xw = 2.4 %, aw = 0.220, Hy = 23.0 %, S = 96.9 %, D10 = 10.6 μm, D50 = 23.4 μm and D90 = 169.3 μm, TP = 1228.2 mg gallic acid equivalent/100 g, ABTS = 2295.9 mg Trolox equivalent (TE)/100 g, DPPH = 5192.3 mg TE/100 g, L* = 80.5, a* = 5.1 and b* = 17.4. SD is an effective technology that positively impacts the development of new food products. In addition, the YP could have multipurpose applications for the industry, generating value in this agri-chain.

Effect of moisture content on the mechanical performance of 3D printed continuous reinforced two-matrix composite

Additive manufacturing, particularly Fused Filament Fabrication, has gained significant attraction in recent years. In order to increase the mechanical performances of several components, continuous reinforcements, such as carbon fibers, can be coextruded with a polymeric matrix.The present study relies on a specific 3D printing process, called towpreg coextrusion, which exploits continuous carbon fibers covered with an epoxy resin and polyamide (PA) as the thermoplastic matrix, thus obtaining a 3D printed two-matrix composite. Since polyamide is a highly hygroscopic material, the impact of moisture content on the mechanical properties of 3D-printed continuous composites was investigated. Tensile and flexural specimens were manufactured and tested under both undried and dried conditions. Drying treatment was carried out at a temperature of 70 °C for 2 h in oven, with weight measurements before and after for quantifying weight loss and then the moisture removal. Additionally, through thermogravimetric analysis, the thermal stability of the material was assessed. It was observed that the drying process allows for a reduction of up to 0.56% by weight of moisture in the specimens. Thus, the drying process led to an improvement in the mechanical properties of the material. Specifically, the tests reveal a 15% increase in tensile strength and an 11.5% increase in flexural strength following the drying process, reaching values of 392.78 MPa and 151.06 MPa, respectively. Similarly, an increase in the tensile and flexural moduli was noted in the treated specimens. Finally, fractured samples underwent optical and scanning electron microscopy analysis, through which different fracture mechanisms of the material and the presence of macrovoids and microvoids attributable to the 3D printing process were observed. Knowledge of deposition defects represents an important starting point for the improvement of the process and the mechanical properties obtained to date. This research provides valuable insights into optimizing 3D-printed continuous composites, emphasizing the importance of moisture control for superior mechanical performance in industrial applications.

Tailoring the covalent organic frameworks based polymer materials for solar-driven atmospheric water harvesting

Atmospheric water harvesting through reticular materials is an innovation that has the potential to change the world. Here, this study offers a technique for creating a solar-powered hygroscopic polymer material for atmospheric water harvesting with the reticular materials. The results show that the porous hygroscopic polymer materials can achieve high performance with high vapor capture (up to ac. 28.8–49.7 mg/g at 28–38 %RH and 25 ℃), rapid photothermal conversion efficiency (up to 32.2 ℃ within 15 min under 1000 W/m−2 light at 25 ℃), a low desorption temperature (lower than 40 ℃), and an effective water release rate. Besides, the material also has excellent water-retention properties, which can effectively store desorbed liquid water in polymer networks for use by vegetation during water demand periods. The strategy opens new avenues for atmospheric water-harvesting materials, which will hopefully solve the global crisis of freshwater shortages.

Hygroscopic assisted solar photo-thermal-electric conversion system for all-day power generation and daytime water collection

In the field of solar thermal electricity, it is difficult to achieve efficient solar energy utilization during the day and continuous power supply day and night at the same time. To address this issue, an integrated system for daytime photothermal power generation combined with waste hot water evaporation and nighttime hygroscopic exothermic power generation has been designed. The system consists of multifunctional composite hydrogel, thermoelectric generator, and hydrophilic porous foam from top to bottom. Among them, the multifunctional composite hydrogel is a crosslinked sodium alginate (SA) loaded with photothermal material polypyrrole (PPy) and hygroscopic material CaCl2, and the hydrophilic porous foam is a PDMS treated by pore-making and oxygen plasma. During the night, CaCl2 and SA in the hydrogel absorb ambient moisture and then release heat, causing the temperature difference between the two sides of the thermoelectric generator to generate electricity with a power of 15.1 mW m−2. During the day, PPy in the hydrogel converts sunlight into heat for the thermoelectric generator to generate electricity with a power of 141.8 mW m−2, and the waste heat of the thermoelectric generator is then used to evaporate the water in the porous PDMS with a rate of 1.311 kg m-2h−1, realizing the multi-stage utilization of solar energy with a high efficiency of 80 %. Therefore, this integrated system can not only use solar energy efficiently, but also generate electricity continuously day and night.

Smart coating materials of buildings for atmospheric water harvesting and response

The promising atmospheric water harvesting technology has been the focus of much attention for the challenge of alleviating global water scarcity. Here, we report a smart coating material for buildings, in short, super hygroscopic material(SHM) modified calcium silicate hydrate (CSH) by using a three-dimensional gel as support, for the first time. The obtained coating material achieves not only ultra-high humidity capture capacities (over 463 mg/g of its weight under room temperature with a relative humidity of 98%) but also rapid and obvious color variations as a response to humidity capture that is visible to the naked eye. More importantly, the above-mentioned phenomenon can be repeated over a wide temperature (4–40 °C) and humidity (43–98 %) range, suggesting that the present coating material has a promising potential to be applied in the real-world humidity capture and response of buildings.

Humidity Sensing Using a Multimode Fiber Ring Laser with Thermal Compensation

We propose a multimode fiber laser sensor utilizing PI-SMF (polyimide-coated single mode fiber) for low-error relative humidity (RH) measurement, which is temperature compensated based on FBG. The PI-SMF in the laser cavity is used as a sensing element, and its length varies with humidity and temperature by volume-variation induced strain, which leads to frequency shift of the longitudinal mode beat frequency signal (BFS). When the 2000 MHz BFS is selected as the sensing signal, a RH sensitivity of −2.68 kHz/%RH and a temperature sensitivity of −14.05 kHz/°C are achieved. The peak shift of the FBG-based laser emission spectrum is only sensitive to temperature rather than RH with a temperature sensitivity of 9.95 pm/°C, which is used as the temperature compensation for RH measurements. By monitoring the response of the BFS and the laser wavelength, the cross-sensitivity effect of RH and temperature is overcome, and low-error RH measurement in the temperature range of 20 to 65 °C is realized with errors within ±0.67 %RH (25 to 85 %RH). The scheme does not require the design and production of complex structures and hygroscopic material coating processes, owning the advantages of simple structure, easy operation and high accuracy, and is expected to be practically applied in food safety and environmental monitoring.

In situ Electrical Impedance Tomography for Visualizing Water Transportation in Hygroscopic Aerogels.

The global water crisis demands immediate attention, and atmospheric water harvesting (AWH) provides a viable alternative. However, studying the real-time subtle relationship between water absorption, diffusion, and internal structure for hygroscopic materials is challenging. Herein, a dynamic visualization technique is proposed that utilizes an in situ electrical impedance tomography (EIT) system and a precise reconstruction algorithm to achieve real-time monitoring of the water sorption process within aerogels from an internal microstructural perspective. These results can be inferred that composites' pore sizes affecting the kinetics of their moisture absorption. In addition, the diffusion path of moisture absorption and the distribution of stored moisture inside aerogels exhibit intrinsic self-selective behavior, where the fiber skeleton of the aerogel plays a crucial role. In summary, this work proposes a generic EIT-based technique for the in situ and dynamic monitoring of the hygroscopic process, pointing to an entirely new approach regarding research on AWH materials.

Solar-powered porous polymer materials-enabled rapid atmospheric water harvesting and storage of liquid water

Atmospheric water harvesting (AWH) is emerging as a promising strategy to produce fresh water from abundant airborne moisture to reduce the global clean water shortage. Hydrogels are considered attractive adsorbents due to their higher water retention and tunable polymer-water interactions. Here, we report the super hygroscopic polymer material (SHPMs) using modified NH2-MIL-101(Cr) as a functional crosslinker by copolymerization with acrylic acid and 2-Acrylamide-2-methylpropanesulfonic acid, achieving a water uptake of about 28.8–49.7 mg/g at 28–38 % RH. The material can desorption quickly under sunlight, and the desorbed water can be stored in a polymer skeleton for use by vegetation or crops during periods of water demand. Besides, the Water retention and storage performance and its outdoor experiment also proved that the application of this material in agriculture, forestry and desertification control laid the foundation to improve the effective availability of soil moisture and water harvesting and conservation. With its excellent water retention and atmospheric water harvesting performance, the material offers a sustainable method for rapid water extraction in arid climates.

Particle discrimination in a NaI crystal using the COSINUS remote TES design

The COSINUS direct dark matter experiment situated at Laboratori Nazionali del Gran Sasso in Italy is set to investigate the nature of the annually modulating signal detected by the DAMA/LIBRA experiment. COSINUS has already demonstrated that sodium iodide crystals can be operated at mK temperature as cryogenic scintillating calorimeters using transition edge sensors, despite the complication of handling a hygroscopic and low melting point material. With results from a new COSINUS prototype, we show that particle discrimination on an event-by-event basis in NaI is feasible using the dual-channel readout of both phonons and scintillation light. The detector was mounted in the novel remoTES design and operated in an above-ground facility for 9.06 g·d of exposure. With a 3.7 g NaI crystal, e−/γ events could be clearly distinguished from nuclear recoils down to the nuclear recoil energy threshold of 20 keV. Published by the American Physical Society 2024

Moisture buffer value for hygroscopic materials with different thicknesses

Moisture buffer value (MBV) is a critical parameter for assessing hygroscopic material's ability to moderate indoor humidity variation. The original MBV theory is strictly valid only for a semi-infinite (or “very thick”) material. When the material is thinner than semi-infinite, the material's thickness will affect its moisture buffering ability. The existing MBV theory is inapplicable. This study proposed a new numerical method to calculate a material's MBV at different thicknesses. The proposed model is simple and efficient. The relation between a material's MBV and thickness and the optimal thickness can be obtained without extensive experimental measurement. What's more, the material's adsorption and desorption isotherms, as well as the material's hysteresis loop and scanning isotherms, are incorporated in the proposed model, making it applicable to advanced desiccant materials like Metal-Organic Frameworks (MOFs). MIL-100(Fe), one of the most promising MOF candidates for indoor humidity control, was used to validate the newly developed model. MBVs of MIL-100(Fe) samples with different thicknesses were measured, and the experimental data closely matched the simulated results. Finally, a building energy consumption simulation model was developed based on the proposed numerical model. A MOF panel with its optimal thickness was placed in the BESTEST typical office room located in Copenhagen. The results show that MOF can reduce about 30 % of the energy consumption of air conditioning in a purely passive way.

Wood dimensional stability enhancement by multivalent metal-cation-induced lignocellulosic microfibrils crosslinking

Wood is a hygroscopic material that responds to the moisture changes of the surrounding environment through swelling and shrinkage, making it dimensionally unstable. Here, we introduce a facile metal-ion-modification (MIM) approach to enhance the dimensional stability of wood. The MIM process involved swelling the wood samples with aqueous metal ion solutions and drying. The high valent metal cations, such as Fe3+, Al3+, and Zr4+, interacted with the hydrophilic groups (e.g., OH, COOH) present in the wood fibers, limiting their access to water and moisture, thereby enhancing the wood's hydrophobicity and dimensional stability. Evaluation of three wood species, southern yellow pine, poplar, and red oak, revealed water contact angles of 120–130° after MIM, indicative of enhanced surface hydrophobicity. Fe3+ treatment decreased southern yellow pine's swelling ratio from 6 % to 4 %. Fe3+-treated wood exhibited tangential anti-swelling efficiencies ranging from 39.83 % to 57.14 % and radial anti-swelling efficiencies from 34.74 % to 48.33 %, varying across wood species. The enhancement of wood dimensional stability can be attributed to the formation of irreversible coordination bonds between metal cations and lignocellulosic microfibrils in the wood cell wall. These bonds prevent the microfibrils from slipping in response to moisture absorption and desorption.