Hybrid Composite Samples Research Articles

New Eco-Friendly Thermal Insulation and Sound Absorption Composite Materials Derived from Waste Black Tea Bags and Date Palm Tree Surface Fibers.

A tremendous amount of waste black tea bags (BTBs) and date palm surface fibers (DPSFs), at the end of their life cycle, end up in landfills, leading to increased pollution and an increase in the negative impact on the environment. Therefore, this study aims to utilize these normally wasted materials efficiently by developing new composite materials for thermal insulation and sound absorption. Five insulation composite boards were developed, two were bound (BTB or DPSF with polyvinyl Acetate resin (PVA)) and three were hybrids (BTB, DPSF, and resin). In addition, the loose raw waste materials (BTB and DPSF) were tested separately with no binder. Thermal conductivity and sound absorption coefficients were determined for all boards. Thermal stability analysis was reported for the components of the tea bag (string, label, and bag) and one of the composite hybrid boards. Mechanical properties of the boards such as flexural strain, flexural stress, and flexural elastic modulus were determined for the bound and hybrid composites. The results showed that the thermal conductivity coefficients for all the hybrid composite sample boards are less than 0.07 at the ambient temperature of 24 °C and they were enhanced as the BTB ratio was reduced in the hybrid composite boards. The noise reduction coefficient for bound and all hybrid composite samples is greater than 0.37. The composite samples are thermally stable up to 291 °C. Most composite samples have a high flexure modulus between 4.3 MPa and 10.5 MPa. The tea bag raw materials and the composite samples have a low moisture content below 2.25%. These output results seem promising and encouraging using such developed sample boards as eco-friendly thermal insulation and sound absorption and competing with the synthetic ones developed from petrochemicals in building insulation. Moreover, returning these waste materials to circulation and producing new eco-friendly composites can reduce the number of landfills, the level of environmental pollution, and the use of synthetic materials made from fossil resources.

Evaluation of tribological parameters for boron carbide and graphite infused aluminium hybrid composite fabricated by stir casting technique

The present work focuses on suggesting Gr as a valuable self-lubricating reinforcement for hybrid composite samples and offering a minimum wear rate for sliding pairs with fewer mechanical surface defects at the same time. A series of samples were fabricated using the route by stir casting method considering B4C and Gr as the two reinforcements. The morphology of the sample has been studied using the X-ray diffraction graphs, Energy dispersive X-ray analysis and Scanning electron imaging stating the homogeneity of reinforcement in various composite cast. The theoretical and experimental density of the series of samples has been studied and compared stating the low porosity of the samples fabricated. A maximum wear rate (Wr) of 0.351 × 10−4 mm3/m. was found for pure aluminium sample against EN31 steel disc with 0.053 as friction coefficient (µ). Wr was somehow seen to reduce up to 0.286 × 10−4 mm3/m for Al-B4C composite with µ of 0.48. For hybrid samples, the wear rate was further seen to improve to 0.187 × 10−4 mm3/m for Al-B4C and Gr 2.0% weight with µ of 0.38. Least Wr was found for composite having Gr 3.5% weight, of 0.149 × 10−4 mm3/m. with µ of 0.36. SEM images of the worn surface give evident results for delamination and crack formation on the pin face for the pure-Al sample. Taguchi-ANOVA analysis has been carried out showing the valid contribution of pin type, load and sliding speed on Wr and friction coefficient as the P-value lies below 0.05 for input parameters considering the 95% confidence level of the model developed. An F-value of 44.57 with R2 of 0.895 is developed for Wr model and an F-value of 54.2 with R2 of 0.934 for the µ model.

Mechanical and metallurgical properties of a glass fiber-reinforced Al7075 hybrid composite produced by infiltration and after aging and abrasion

Abstract Within the scope of this study, composite structures were produced by reinforcing Al7075 with 6 mm size glass fiber (GF) scrap at different weight rates (2–3 %) using the infiltration method. Mechanical and metallurgical examination of unreinforced Al7075 samples and reinforced Al7075 composite samples were carried out. After the aging heat treatment of the samples, pin-on-disc wear and hardness tests were performed. FESEM and EDS analyses were conducted to examine the hardness and microstructural changes caused by the applied processes on the samples. It was observed that GF reinforcement increased the hardness of the material and there was full wettability between Al 7075 and GF. Thus, wear resistance increased. The highest hardness and wear resistance were obtained in the 6 h aged 2 wt.% GF-reinforced Al 7075 matrix hybrid composite sample. In addition, it was observed that the distribution of GF scrap added as reinforcement at a rate of 2 wt.% in Al 7075 was homogeneous, and the hardness measurements taken from different areas were similar.

Investigation of wear characteristics of granite dust & coconut shell ash reinforced aluminum metal matrix composite using design of experiment

Recently, one of the most important issue faced by all nations is a waste management. Therefore, it is essential to search for creative solutions to waste reduction, reuse, and recycling. This can be accomplished by adding waste materials to composite materials as a reinforcements. Reusing waste materials enhances the characteristics of existing materials, while also helping the environment by solving the disposal problem. The main aim of this paper is to study the wear characteristics of hybrid aluminum metal matrix composite reinforced with coconut shell ash (CSA) and granite dust. The hybrid composite samples were manufactured using stir casting by reinforcing CSA (ranging from 0 wt% to 12 wt%) and granite dust (maintained at 2 wt%) in Al6061 alloy. SEM and EDAX analysis were performed to investigate the microstructure and elemental composition. The wear characteristics of the hybrid composites were determined via pin-on-disc tests. Finally, the Taguchi design of experiment was performed on the specimen having the best wear characteristics by selecting the L27 orthogonal array and identified the influence of process variables on the wear rate. The results of the pin-on-disc experiment showed that the wear rate decreased with increasing CSA%. The hybrid composite composed of 02 wt% granite dust, & 12 wt% CSA indicates a lower wear rate (56.25%) as compared to the matrix alloy. The Taguchi analysis prooved that the sliding distance has a greater impact on the wear rate than the other parameters. This material can be a superior substitute where high wear resistance is required.

Tensile and Impact Properties of Woven Glass Fibers/Epoxy Composites Filled with Short Glass Fibers

Glass fiber/polymer composites are widely utilized in many structural applications because of their high specific strength and stiffness-to-weight ratios. In this study, woven glass fiber/epoxy was hybridized with short glass fibers of different lengths (2, 4, 6, 2+4, 2+6, and 4+6 mm) and contents (3, 6, 9, and 12 wt%) to produce hybrid woven SGF/epoxy composites. Variations in the thickness, fiber volume fraction, density, and void content of the prepared composites were determined. Mechanical tests such as tensile and Charpy impact tests were conducted. Compared to the woven fabric composites without short glass fibers (control samples), the tensile strength increased by approximately 13% at an optimum weight fraction of 3 wt% using short glass fiber lengths of 4 mm. Meanwhile, the incorporation of short glass fibers into the woven glass composites decreased the tensile modulus for all lengths. The maximum enhancement in the impact strength (approximately 14%) was achieved by the hybrid composite samples reinforced with 4 mm of short glass fibers at 3 wt%. This hybrid composite offers 18% and 20% improvements in the specific tensile and impact strengths, respectively. In summary, filling the woven fabric composites with specified short fiber contents and lengths can increase their mechanical performance when resin-rich regions are reinforced with short fibers without forming relatively thick interleaves between the woven fabric plies

Extraction and characterization of novel Prosopis Juliflora bark and Boehmeria nivea fibre for use as reinforcement in the hybrid composites with the effect of curing temperature, fibre length and weight percentages

The hybrid composite sample based on Prosopis Juliflora (PJ) bark and ramie fibre with different length, weight percentage, and curing temperature were created for the first time in this work. Totally, 120 hybrid composite samples were tested in this study. There were five different fibre lengths: 10 mm, 15 mm, 20 mm, 25 mm, and 30 mm, weight percentages 10 %, 20 %, 30 %, 40 %, and 50 %, and different curing temperatures 80 °C, 90 °C, 100 °C, 110 °C, and 120 °C used to produce the hybrid composite samples. Due to the cross-linking ability with the epoxy matrix, the hybrid composite specimen shows high resistance up to 98 Shore D hardness. The high polarity of the epoxy matrix and the hydrogen bond strengthening effect, increased the composite sample flexural strength by 12 %. The curing temperature of 100 °C, 20 mm fibre length, and 30 % of the hybrid composite sample achieved the highest tensile strength (28.76 MPa), flexural strength (46.54 MPa), impact strength (4.5 J), and hardness strength properties (98 shore D). Thermo gravimetric analysis (TGA) revealed the composite samples initial decomposition temperature (Ti) at 98 °C, maximum decomposition temperature (Tmax) at 320 °C, and the final decomposition temperature (Tf) at 466 °C.

Impact response of hybrid composites under varying environmental conditions: A comparative study

AbstractComposite materials are widely preferred in the aviation, automotive, construction and maritime industries due to their many superior properties. As a result of this widespread use, composite structures are inevitably subjected to various environmental conditions. Various environmental conditions may negatively affect the mechanical performance of the structure, and the structure may become unable to maintain its initial mechanical properties, especially in the face of critical loading, such as low‐velocity impacts. This research investigated the influence of various environmental conditions on the low‐velocity impact strength of composite materials. 12‐layer plate samples with epoxy matrix reinforced with woven glass fabric (GF), woven carbon fabric (CF), and hybrid fabric (HF), where the two fabrics are used together, were produced. Low‐velocity impact tests were conducted to these specimens at 20 and 40 J energy levels. Damages occurring in the material as a result of the low‐velocity impact test were interpreted using high‐resolution camera and optical microscope images. Force‐time and force‐ displacement curves were drawn and interpreted. It was concluded that as the impact energy values increased, the maximum force and displacement values also increased.Highlights The influence of various environmental conditions to which composite materials may be exposed on the dynamic response of the structure has been investigated. Various environmental conditions significantly affected the composite structure's impact behavior. While glass fabric (GF) composite samples were more affected by the seawater environment, carbon fabric (CF) composite samples were more affected by the HCl environment. Hybrid (HF) composite samples were affected by seawater and HCl in approximately equal amounts.

Mechanical, Tribological, and Biological Properties of Short Carbon Fiber/ Nano Hydroxyapatite Reinforced Hybrid Epoxy Composites

This investigation intends to examine the mechanical, tribological, and biological properties of hybrid epoxy composites reinforced with nanohydroxyapatite (nHA) and short carbon fiber (SCF). Due to its advantageous mechanical, tribological, and biocompatibility features, the proposed E/SCFs-nHA hybrid composites are meant to be recommended for composite structures that can be used to develop fixation plates used in orthopedic applications. In this study, single-layer hybrid composites reinforced with SCFs and nHA in varying ratios, as well as pure epoxy (E) and epoxy-carbon fiber composites, were all fabricated by hand lay-up method. Tensile tests, 3-point bending tests, and Izod impact tests were performed to investigate their mechanical characteristics. Moreover, the hybrid composite samples were tested for their biological properties in simulation body fluid (SBF). Mechanical and biological properties were found to be enhanced according to the results. Consequently, the hybrid composite (E-10CF-3nHA) of 10% carbon fiber (CF) and 3% nanohydroxyapatite (nHA) performed the best in all tests.

New Composites Derived from the Natural Fiber Polymers of Discarded Date Palm Surface and Pineapple Leaf Fibers for Thermal Insulation and Sound Absorption.

New composites made of natural fiber polymers such as wasted date palm surface fiber (DPSF) and pineapple leaf fibers (PALFs) are developed in an attempt to lower the environmental impact worldwide and, at the same time, produce eco-friendly insulation materials. Composite samples of different compositions are obtained using wood adhesive as a binder. Seven samples are prepared: two for the loose natural polymers of PALF and DPSF, two for the composites bound by single materials of PALF and DPSF using wood adhesive as a binder, and three composites of both materials and the binder with different compositions. Sound absorption coefficients (SACs) are obtained for bound and hybrid composite samples for a wide range of frequencies. Flexural moment tests are determined for these composites. A thermogravimetric analysis test (TGA) and the moisture content are obtained for the natural polymers and composites. The results show that the average range of thermal conductivity coefficient is 0.042-0.06 W/(m K), 0.052-0.075 W/(m K), and 0.054-0.07 W/(m K) for the loose fiber polymers, bound composites, and hybrid composites, respectively. The bound composites of DPSF have a very good sound absorption coefficient (>0.5) for almost all frequencies greater than 300 Hz, followed by the hybrid composite ones for frequencies greater than 1000 Hz (SAC > 0.5). The loose fiber polymers of PALF are thermally stable up to 218 °C. Most bound and hybrid composites have a good flexure modulus (6.47-64.16 MPa) and flexure stress (0.43-1.67 Mpa). The loose fiber polymers and bound and hybrid composites have a low moisture content below 4%. These characteristics of the newly developed sustainable and biodegradable fiber polymers and their composites are considered promising thermal insulation and sound absorption materials in replacing synthetic and petrochemical insulation materials in buildings and other engineering applications.

Fabrication and Physico-mechanical Characterization of Short Natural/Synthetic Fiber–Reinforced Hybrid Composites: Effects of Biodegradation and Chemical Aging

The main goal of this study was to develop eco-friendly and low-cost multiple short natural fiber-reinforced hybrid composites with the hybridization of comparatively high-strength glass fibers. The hybrid composites were fabricated via hand lay-up by using short jute, silk, water hyacinth, and glass fibers for the reinforcements and unsaturated polyester resin for the thermoset polymer matrix. The reinforcing fibers were randomly oriented, and five types of hybrid composites were fabricated with different types of fiber content (wt.%). The performance of the manufactured hybrid composites was assessed by tensile, flexural, and impact testing, as well as water uptake (%). It was revealed that composites with high glass fiber content (wt.%) exhibited optimum mechanical performance in most cases, while poor moisture resistance performance was exhibited for the hybrid composites containing higher natural fibers (wt.%). The hybrid composite samples were also aged in soil medium (biodegradation) for 25 days and different chemical solutions (alkaline, acidic, and salt) for 10 days. After biodegradation, the drop of tensile strength (TS) and tensile modulus (TM) was revealed to be approximately 38–61 and 58–72%, respectively. On the other hand, after chemical aging, the drop of TS and TM was exhibited to be approximately 49–76% and 51–65%, respectively, for alkali solution aging; 42–75% and 29–76%, respectively, for acid solution aging; and 43–59% and 51–65%, respectively, for salt solution aging.

Photothermal defect imaging in hybrid fiber metal laminates using the virtual wave concept

This study presents photothermal imaging results of subsurface material defects within fiber metal laminates utilizing the virtual wave concept. Therefore, we theoretically analyze the propagation of the virtual wave signal in a hybrid composite laminate via the method of images. For provoking local material damage, the hybrid composite sample is subjected to a defined impact loading. The results obtained from photothermal defect imaging, utilizing rectangular laser pulse excitation, are compared with results obtained from 3D x-ray computed tomography. To sum up, we demonstrate a fast, non-invasive, and easily interpretable reconstruction of defects within macroscopic hybrid composite laminates based on the virtual wave concept.

Assessment of mechanical and tribological behavior of Mg-4Zn-1RE-0.7Zr alloy: Novel mixture of Si3N4/TiC/MoS2 utilizing casting technique

In the modern era, manufacturers aim for their parts to possess a sleek finish and increased durability to ensure continued functionality. Both the automotive and aerospace industries are actively seeking new materials and methodologies to enhance the surface quality of components during the preparation process and make the most of available resources. Employing casting, advanced techniques, and new materials is crucial for achieving this goal. Industries commonly utilize alloys and composite materials in the production of their components. This study focuses on magnesium composite Mg-4Zn-1RE-0.7Zr alloy to find the influence of varying three different reinforcement particles on mechanical properties and wear rate. An attempt was made to choose a constant 5% Si3N4 as the primary reinforcement and 2.5% to 7.5% of TiC/MoS2 as the secondary reinforcement, respectively. The samples of magnesium hybrid composites are prepared using a centrifugal casting process. The ZE 41 alloy/5% (TiC-MoS2)/5%Si3N4 has a high tensile strength of 942 MPa. In addition, 5% TiC/5% MoS2 with 5% Si3N4 composite has enhanced hardness, which is beneficial for transmission in aircraft like Boeing 727 and die-casting fittings in automobile applications.

Moisture diffusion analysis and their effects on the mechanical properties of organic particle filled natural fiber reinforced hybrid polymer composites

This investigation explores the water intake characteristics of hybrid composite samples composed of Wood Dust as organic filler (WD), Prosopis Juliflora as fiber (PJF), and epoxy as matrix. The specimens underwent immersion in both distilled and seawater environments for a duration of 240 hours. The composite samples, with compositions of 10WD + 30PJF + 60 PF, 20WD + 20PJF + 60 PF, and 30WD + 10PJF + 60 PF, were subjected to moisture content measurements at different intervals. Mechanical properties were tested following ASTM standards for both dry and wet conditions. Results indicate that seawater immersion leads to higher moisture absorption compared to distilled (condensed) water, with the fiber (PJF)-rich composite (30PJF +10WD + 60 PF) exhibiting the greatest water absorption. The water absorption pattern exhibited by the hybrid composite of WD/PJF/PF does not adhere to a Fickian behavior. Tensile, flexural, and impact properties were evaluated, with the (10WD + 30PJF + 60 PF) specimen showcasing superior performance in dry conditions, boasting a tensile character of 51 MPa, flexural (bending) strength of 60 MPa, and impact value of 1.4 KJ/m2. However, its strength diminishes upon exposure to distilled water and seawater. SEM analysis of fractured surfaces from seawater-exposed specimens provides additional insights. In conclusion, this study sheds light on the influence of immersion on moisture absorption and mechanical properties, emphasizing the prevalence of non-Fickian behavior and the varying performance of different compositions, with the (10WD + 30PJF + 60 PF) composition demonstrating remarkable strength under dry conditions.

Effect of processing conditions and electrode materials on the surface roughness of EDM-processed hybrid metal matrix composites

The current investigation aims to investigate the role of four major input parameters, i.e. Current (I), Gap Voltage (V), Pulse off time (Toff), and Pulse duration (Ton) on surface roughness (Ra) of Al–Mg-0.6Si-0.275Cu/SiC10 % hybrid composite samples fabricated by Stir-casting. In addition, paper focuses on the goal to ascertain the impact of distinct tool materials on surface morphology of Al/SiC composite. Further, mathematical models were developed using the L29 orthogonal array in the Stat-Ease Modelling Expert V7.0 software. Thus, to validate the significance of the developed models, an Analysis of Variance was used. Finally, the topography of the specimen's surface (pre and post-machining) was performed using scanning electron microscopy (SEM). The results showed that at a peak current of 5 Amp, Gap voltage of 100V, Pulse on time of 100 μs, and Pulse off time of 40 μs, the lowest surface roughness with brass and copper electrodes was 0.29 μm and 0.32 μm obtained. The Brass electrode yielded 9.3 % lower surface roughness than the copper electrode.

Effect of TiB2 and GNP reinforcements on machinability in drilling of Al7075/TiB2/GNP hybrid composites produced by powder metallurgy

In this study, it has been aimed to investigate the machinability performances by drilling by producing Al7075 matrix hybrid composite samples with graphenenanoplate (GNP) and titaniumdiboride (TiB2) reinforced at different rates by powder metallurgy. The impacts of GNP and TiB2 reinforcing materials on the cutting parameters and wear behavior of the cutting tool have been examined and discussed. As a result of the drilling tests which are carried out by applying different cutting parameters, it was observed that GNP additive has positive impact on the cutting forces, surface roughness, and hole quality in general. As a result of the machining experiments, the lowest cutting force was obtained as 150 N at a feed rate of 0.100 mm/rev and a cutting speed of 60 m/min in the 1% GNP reinforced sample. The minimum roughness value was obtained as 0.886 micron at 60 m/min cutting speed in the 1% GNP reinforced sample. The minimum deviations from cylindricality and circularity were also measured as 0.03 and 8.005 mm from the 1% GNP reinforced sample. While the lubricating effect was low with a GNP ratio of 0.5%, the abrasive effect was observed more with a GNP ratio of 1.5%. While GNP supplementation decreased the diameter deviation and cylindrical deviation values, it increased the perpendicularity deviation values. In general, swarf chip formation occurred with a small amount of flank wear on the cutting tools. While hard TiB2 reinforcement particles in the composite structure were effective in flank wear, the most important cause of chip formation was the presence of ductile aluminum matrix and relatively low cutting speeds. When the entire experimental study was evaluated, it was evaluated that the solid lubricant property of the GNP reinforcement material was effective at the most 1% GNP reinforcement rate.

Mechanical and antibacterial properties of hybrid polymers composite reinforcement for biomedical applications

This research investigates the biocompatibility, mechanical strength, and tribological properties of a hybrid composite material composed of high-density polyethylene (HDPE), hydroxyapatite (HAp), and titanium dioxide nanoparticles (Ti ). The study explores the microstructural characteristics of the composite material using scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). Samples of HDPE-30%HAp with varying concentrations of Ti (5, 10, 15, and 20%) were prepared and extruded using a twin-screw machine. The hybrid composite materials underwent mechanical tests (tensile, flexural, and hardness), tribological tests (friction and wear rate), and antibacterial tests (resistance to Escherichia coli and Staphylococcus aureus bacteria). The results indicate that the optimal hybrid composite sample was HDPE-30%HAP-10% Ti , which demonstrated excellent mechanical properties (maximum tensile strength of 25.93 MPa and young modulus of 480 MPa) and a low coefficient of friction (COF∼ 0.07) while achieving high wear resistance (wear rate in the order of 1m ). The study shows that the improvement in mechanical properties results in a corresponding improvement in tribological properties. The antibacterial tests revealed that the hybrid composite material exhibited resistance to E. coli and S. aureus bacteria. The findings of this study suggest that the HDPE-30%HAP-10% Ti composite is a promising material for use in biomedical applications due to its excellent biocompatibility and desirable mechanical and tribological properties. The study demonstrates the potential of reinforced hybrid composite materials in overcoming the disadvantages of monolithic and hybrid micro-composites and highlights the importance of investigating the microstructural, tribological, and mechanical strength characteristics of composite materials for biomedical applications.

Mechanical and tribological properties of snake grass fibers reinforced epoxy composites: effect of Java plum seed filler weight fraction

Abstract Natural fiber composite materials are able to compete with common synthetic materials in situations where the strength-to-weight ratio is important. In this study, we aim to analyze the mechanical, tribological, and surface morphology of composites fabricated from randomly oriented snake grass natural fiber with java plum seed filler. Different weight ratios of fiber to seed filler are chosen: 30:0, 28:2, 26:4, 24:6, 22:8, and 20:10. A 70 % epoxy resin was kept constant in all compositions. The fabricated hybrid composite samples were subjected to tensile, flexural, shear, Shore D hardness, water absorption, and wear tests as per ASTM standards, and the results were compared with those of snake grass mono fiber composites. The 20:10 composite has the maximum tensile strength, impact resistance, flexural strength, hardness, water absorption, and wear resistance compared to other composites. The fiber/matrix adhesion was explored using a scanning electron microscope (SEM). The 20:10 composite shows predominant mechanical and tribological characteristics, making it easier to utilize in structural and automotive applications.

Fabrication and characterization of laminated natural fibers and SS303 wire mesh reinforced epoxy-based hybrid composite

In today’s world, researchers are actively seeking the most suitable materials to meet the growing industrial demands. These materials need to possess specific characteristics such as lightweight nature, high strength, excellent mechanical properties, and environmental friendliness. Due to these requirements, relying solely on mono fiber composite materials is insufficient. Therefore, it has become necessary to incorporate different reinforcements into polymer matrices to achieve the desired mechanical properties. This study focuses on the fabrication of a novel hybrid composite using jute fibers, luffa fibers, palmyra leaf fibers, and AISI 303 (0.5 mm) wire mesh combined with epoxy resin. The fabrication process involved utilizing vacuum bagging techniques. To assess the mechanical properties of the hybrid composites, two wire mesh orientations (45° and 90°) and a total of 12 stacking sequences of jute/wire mesh/luffa/palmyra (J/W/L/P) were selected. The mechanical characterization of the hybrid composites included tensile, impact, flexural, and interlaminar strength tests. Furthermore, a dynamic mechanical analyzer (DMA-8000) was employed to investigate the elastic behavior, including storage modulus (E′), loss modulus ( E″), and damping factor (tan δ). Additionally, the fracture surface's microstructure was examined using a scanning electron microscope (SEM). Among the various stacking sequences and fiber orientations, the 45° fiber orientation and the stacking sequences JWLP, JLWP, JWPL, JPWL, PWJL, and PJWL exhibited superior ultimate tensile strength. Notably, the PWJL stacking sequence displayed the highest average tensile strength (74.83 MPa), flexural strength (131.60 MPa), percentage elongation (1.35%), and interlaminar strength (1.47 kN). Moreover, dynamic mechanical analysis revealed that the hybrid composite sample with 90° wire mesh orientation exhibited a peak energy absorption of 0.820 at the transition region, specifically at a frequency of 0.5 Hz.

Improved double impact and flexural performance of hybridized glass basalt fiber reinforced composite with graphene nanofiller for lighter aerostructures

The growing demand for sustainable, lightweight yet rigid and cost-effective materials for airplane construction served as the impetus for this work. An E-glass fiber (400 GSM) is layered in a 6:2 ratio with natural basalt fiber and infused with graphene nanoparticles to produce a more appealing 40% lighter hybrid composite of 1.1 mm thickness for the aviation industry. Samples of hybrid composites with 1% and 2% graphene-to-fiber filler weight ratios are used. Then, using ASTM standard analysis tools, the damage that is caused on toughened laminates during low-velocity drop weight impact tests, tensile, 3-point bending, and Compression After Impact(CAI) is evaluated. The composites' tensile strength, flexural strength, low-velocity double impact, and compression impact strength all significantly improved at 2 wt% graphene, increasing by 37%, 55%, 56%, and 78%, respectively. Scanning Electron Microscope analysis of the damaged area demonstrated the presence of important toughening mechanisms, such as damage confinement through microcracks and improved fiber-matrix bonding. It has been established that adding an optimum blend of graphene and basalt to Glass Fiber Reinforced Polymer(GFRP) results in an unprecedented increase in effective strength with reduced weight.

The morphological and mechanical characterization of UHMWPE based composite: an experimental study

Natural fiber and its hybrid composites have a promising future due to their economic, lightweight, environmentally superior, and sustainable properties. The purpose of this research is to explore the morphological and physical properties of composites made of hemp-epoxy and ultra-high molecular weight polyethylene-hemp-epoxy. The compression moulding technique is used to fabricate the UHMWPE -hemp hybrid composite and hemp-epoxy sample at a different orientation. These samples are subjected to different types of mechanical testing, including flexural, impact, hardness, and tensile tests at different strain rates as per ASTM standards. The result indicates that the flexural strength, impact strength, and hardness of the hybrid composite are more than the hemp composite. Scanning electron microscopy has been used to examine fractography at various strain rates. It is found that with the increase in the strain rate, tensile strength increases. It is observed that there is an increase of more than 56.49% in the specimen’s strength with the addition of 8.3% ultrahigh molecular weight polyethene fiber reinforcement.