Hot Wire Research Articles

Pulsed Magneto‐Oscillation Processing Improves the Quality of SCM435 Cold Heading Steel Billet and Its Hot‐Rolled Wire Rods

Pulsed magneto‐oscillation (PMO) has a high homogenization effect on continuous castings, but the heritability of it on hot‐rolled wire rods has not been studied. Recently, the effect of pulsed magneto‐oscillation on SCM435 cold heading steel billet and its hot‐rolled wire rod were investigated. A 180 mm × 180 mm ten‐strand continuous casting machine was used, with the first strand treated by pulsed magneto‐oscillation, and billets hot‐rolled to Φ6.5 mm wire rods. The results showed that compared with the billet without pulsed magneto‐oscillation treatment, the proportion of central equiaxed grain zone of pulsed magneto‐oscillation treated billet increased from 26.5% to 37.4%, and the secondary dendritic arm spacing of columnar was reduced. Futhermore, the segregation index ranges of Cr and Mn decreased by 47.1% and 33.3%, respectively. For the hot rolled wire rods, the solutes homogeneity and the mechanical properties of the rods produced by pulsed magneto‐oscillation treated billet were improved. And its banded structure was significantly refined, where the maximum band width was reduced from 35.4 μm to 12.3 μm. This study showed that the properties of wire rod could be significantly improved by improving the homogeneity of the casting billet by pulsed magneto‐oscillation, and a good histogenetic effect was obtained.

Experimental investigation of the flow disturbance near the trailing edge of slotted and non-slotted blades using skewness and kurtosis

The present study conducts an experimental investigation into the flow characteristics over a cascade of both slotted and non-slotted compressor blades. The focus is on evaluating potential statistical correlations between higher-order moments of velocity fluctuations, including Skewness and Kurtosis. The linear axial cascade comprises three NACA6409 blades, which are tested in both normal and slotted blade. Data acquisition was conducted using a hot wire anemometer at three measurement stations within the cascade. The hot wire sensor was positioned at distances of x/c = 0.125, 0.25, and 0.5 from the trailing edge (x), where x represents the distance from the probe to the trailing edge of the airfoil and (c) is the chord length of the blade. Measurements were taken at a blade angle of attack of 0° and two Reynolds numbers: 22,750 and 45,500. Results indicate that blade grooving enhances flow velocity, postpones separation and improves flow control in the trailing edge region. By comparing calculated Skewness and Kurtosis values with those predicted by existing boundary layer and free jet relations, more consistent correlations were identified. To provide more accurate relationships, two polynomials of the second and third order have been used. It was found that high-order values of velocity were obtained more accurately with the relations presented in this research. Although the accuracy of these predictions is significantly reduced in the proportion of larger distances. In distant stations, the loss velocity has decreased. As the distance from the model increases, the amount of inhomogeneities in the sequence increases and the values of the opposite Skewness become zero. Turbulence intensity has been reduced by slotting the blades.

HWCVD growth of hydrogenated nanocrystalline silicon oxide window layers for SHJ solar cells

In recent years, successful development of n-type hydrogenated nanocrystalline silicon oxide (n-nc-SiOx:H) window layers with high conductivity and low parasitic absorption, grown by plasma enhanced chemical vapor deposition (PECVD) technology, has significantly enhanced the power conversion efficiency of silicon heterojunction (SHJ) solar cells. Although SHJ solar cells have significant advantages in efficiency, the high cost of the PECVD equipment presents a significant barrier to their mass production. The utilization of the more cost-effective hot wire chemical vapor deposition (HWCVD) technology presents a promising solution. Nevertheless, HWCVD technology currently lacks an industrially viable methodology for growing high-performance window layers due to a phenomenon of associated severe loss of passivation. In this work, the phenomenon and the solution have been investigated. The results demonstrate that, in HWCVD processes, large amounts of hydrogen and small amounts of oxygen, which are essential for enhancing the crystallinity and conductivity and reducing the parasitic absorption, both induce significant damage to the previously grown intrinsic hydrogenated amorphous silicon layer, leading to poor passivation, and hence much lower cell efficiency. Introduction of a densified amorphous silicon barrier layer was found to be an effective solution to the aforementioned passivation loss, resulting in the successful growth of nc-SiOx:H window layers by HWCVD, with an efficiency enhancement of 0.37%abs. Finally, a commercial-size SHJ solar cell with an efficiency of 24.74 % was fabricated using a home-made HWCVD-based pilot SHJ cell line.

Is It Safe to Cauterise Both Sides of the Nasal Septum at the Same Time in Children With Nosebleeds?

It is often recommended that, in children with bilateral epistaxis, only one side of the nasal septum should be cauterised at a time in order to reduce the risk of septal perforation. This advice may have been reasonable when hot wire electrocautery was in common use. The risk of septal perforation after silver nitrate cautery is unknown but probably low. Retrospective case note review of children attending the nurse-led epistaxis clinic between 2019 and 2022. Nine hundred and twenty children were seen in the nurse-led clinic between January 2019 and December 2022. Six hundred and one children (79%) underwent nasal cautery. Simultaneous bilateral nasal cautery was carried out in 176 (29%) children. Our follow up period ranged between 303 and 1744 days, with a median of 809.5 days. No child presented to emergency or ENT services with septal perforation or any other complication of simultaneous bilateral nasal cautery. To the author's knowledge, this is the largest study assessing the safety of simultaneous bilateral nasal cautery with silver nitrate in children. No adverse results have been found after cauterising both sides of the septum at the same sitting, and doing so potentially saves time and money for patients and the health service.

In-situ investigation on tensile deformation behavior of hybrid hot-rolled wire arc additive manufactured Al-Mg alloys

Hybrid hot rolling and wire arc additive manufacturing (HR-WAAM) are becoming an effective way for enhancing both tensile strength and plasticity in Al-Mg alloys. This work systematically studies the microstructural evolution and strengthening mechanisms of HRAM Al-Mg alloys during the stretching process. The results show that interlayer hot rolling can effectively refine grains, reduce defects, and promote uniform precipitation of second phases. Within a lower strain range, uniformly distributed fine grains help prevent the formation of high geometrically necessary dislocation (GND) density in localized areas, thereby reducing local stress concentration. With a higher strain range, this microstructure can promote coordinated grain transformation towards softer orientations, reduce local microstructure work hardening, and allow GND to develop within a broader range of plastic deformation, thereby exhibiting excellent strain coordination ability. These factors collectively contribute to the improved strength and ductility of the material. Compared with traditional WAAM samples, the yield strength, tensile strength, and elongation of HRAM samples have increased by 18 MPa, 92 MPa, and 11 %, respectively. Consequently, this study provides new insights and a theoretical foundation for advancing additive manufacturing technology in the production of high-performance Al-Mg alloys.

Captivating Combustion Traits of Bio-Oil Droplets Enriched with Bio-Additives from the Areca Shell Waste

Fuel derived from crude vegetable oil, such as coconut oil, holds promise as an alternative energy source to mitigate the increasing reliance on fossil fuels driven by population growth and industrial activities. The experiment involved suspending a single droplet of crude coconut oil mixed with activated carbon from areca shell waste and placed at the junction on R-type thermocouple (Pt/Pt-Rh13%). The droplets were ignited using a hot wire and subjected to atmospheric pressure and room temperature. Coconut oil comprises a saturated triglyceride carbon chain compound of approximately 91%, and areca shell waste possesses a porous structure that fosters favorable interactions between fuel molecules. The droplet combustion method was selected to streamline the process and enhance the contact area between air and fuel, thereby boosting the reactivity of fuel molecules. The research found that adding activated carbon shortens the carbon chain, making it more reactive and easier for the fuel to ignite. Specifically, activated carbon significantly enhances fuel performance at a concentration of two parts per million (ppm). At this level, the fuel absorbs heat more effectively and ignites faster compared to one ppm and three ppm levels. Moreover, the results show that heat absorption occurs slowly at one ppm, while at three ppm, the increased molecular mass of the fuel can strengthen carbon-bonding forces. These factors contribute to a longer ignition time for the fuel. The findings suggest that the activated carbon from areca shell waste can play a good role as a combustion catalyst, where overall, fuel performance increases.

Variant selection and macrozone in Ti-6Al-4V walls during laser hot wire direct energy deposition

Variant selection and macrozone in Ti-6Al-4V walls during laser hot wire direct energy deposition

Dependence of Thermal Conductivity on Size and Specific Surface Area for Different Based CoFe2O4 Cluster Nanofluids

Enhancing the thermal conductivity of fluids by using nanoparticles with outstanding thermophysical properties has acquired significant attention for heat-transfer applications. Nanofluids have the potential to optimize energy systems by improving heat-transfer efficiency. In this study, cobalt ferrite nanoparticles clusters with controlled mean sizes ranging from 97 to 192 nm were synthesized using a solvothermal method to develop novel nanofluids with enhanced thermal conductivity. These clusters were comprehensively characterized using transmission electron microscopy, X-ray diffraction, Raman spectroscopy, vibrating-sample magnetometry, and nitrogen physisorption. The CoFe2O4 cluster nanofluids were prepared using the two-step method with various base fluids (water, propylene glycol, and a mixture of both). Dynamic light scattering analyses of the average Z-size of the dispersed nanoadditives over time revealed that the stability of the dispersions is influenced by cluster size and the proportion of glycol in the base fluid. The thermal conductivity of the base fluid and nine different 0.5 wt% CoFe2O4 cluster nanofluids was measured using the transient hot wire method at temperatures of 293.15, 303.15, and 313.15 K, showing different temperature dependencies. The study also explores the relationships between the thermal conductivity, cluster size, and specific surface area of the nanoadditives. A maximum thermal conductivity enhancement of 4.2% was reported for the 0.5 wt% nanofluid based on propylene glycol containing 97 nm CoFe2O4 clusters. The findings suggest that the specific surface area of nanostructures is a more relevant parameter than size for describing improvements in thermal conductivity.

A double-helix plane winding sensor with wire using transient plane source method

The transient plane source (TPS) method is widely used to measure thermophysical properties of various materials, and the high-precision double-helix sensor is a key technology. A novel sensor using an efficient, simple, and low-cost lacquered micron-wire-wound process is proposed to replace traditional complex micro- and nano-etching processes. The TPS test platform was built based on the Wheatstone Bridge theory. A new sensor sample of diameter 5.377 mm was wound with an enameled copper wire of diameter 0.063 mm. Owing to the characteristics of the process, a 1-mm round hole was bored inside the sensor. An analytical solution for the concentric ring heat transfer model of the sensor with a central circular hole structure was derived, and a two-dimensional concentric circle simulation model of the sensor was established. As the number of turns decreased, the average error between the analytical solution of the concentric ring model with a large center hole (LHAS) and that of the traditional concentric circle model (TAS), as well as LHAS and the simulation model, gradually increased. The maximum relative errors between LHAS and TAS, as well as between LHAS and the simulation model, were 23.69 % and 0.1 %, respectively, and the average errors of the absolute maximum were 11.86 % and −0.06 %, respectively. The LHAS exhibited excellent accuracy because of the structural characteristics of the novel sensor. The accuracy of LHAS has been validated by simulation and hot wire method. Temperature rise data of high-borosilicate glass and polytetrafluoroethylene samples at different powers were obtained. The thermal properties of the samples were determined by fitting LHAS and TAS data. The thermal conductivity errors measured by LHAS were smaller than those measured by TAS, the thermal conductivity and thermal diffusivity errors were less than 3.5 % at different powers, and the measured repeatability errors were less than 1 %, indicating the good application prospect of the proposed model.

Wind Tunnel Experiment on the Footprint of a Block-Arrayed Urban Model in a Neutrally Stratified Boundary Layer

This study addresses the need to investigate footprint function features in urban areas and establish a validation database for numerical methods. Concentration and its flux footprints of a block-arrayed urban model were measured in a wind tunnel with a neutrally stratified boundary layer. The velocity and concentration were simultaneously measured by an X-probe hot wire anemometer and a fast-response flame ionization detector to evaluate the vertical flux. Experimental results highlighted the influence of the measurement heights on footprint distributions. Because the sensors were immersed in the roughness sublayer, their footprints showed strong heterogeneity across horizontal positions caused by building configurations. It was found that turbulent flux contributes up to 70% of total flux footprints, emphasizing the importance of accurate turbulent dispersion estimation in numerical methods. Furthermore, measured footprints were compared to those modeled by a widely used analytical method (Kormann and Meixner in Boundary-Layer Meteorol 99:207–224, 2001, https://doi.org/10.1023/ A:1018991015119). The measured footprints extended further along the streamwise direction and their spanwise dispersions were constrained by the rows of blocks, which failed to be reproduced in the analytical method. This indicates the significant effects of building configurations on footprint functions in urban areas.

An Investigation of Thermomechanical Behavior in Laser Hot Wire Directed Energy Deposition of NAB: Finite Element Analysis and Experimental Validation

Laser Hot Wire (LHW) Directed Energy Deposition (DED) Additive Manufacturing (AM) processes are capable of manufacturing parts with a high deposition rate. There is a growing research interest in replacing large cast Nickel Aluminum Bronze (NAB) components using LHW DED processes for maritime applications. Understanding thermomechanical behavior during LHW DED of NAB is a critical step towards the production of high-quality NAB parts with desired performance and properties. In this paper, finite element simulations are first used to predict the thermomechanical time histories during LHW DED of NAB test coupons with an increasing geometric complexity, including single-layer and multilayer depositions. Simulation results are experimentally validated through in situ measurements of temperatures at multiple locations in the substrate as well as displacement at the free end of the substrate during and immediately following the deposition process. The results in this paper demonstrate that the finite element predictions have good agreement with the experimental measurements of both temperature and distortion history. The maximum prediction error for temperature is 5% for single-layer samples and 6% for multilayer samples, while the distortion prediction error is about 12% for single-layer samples and less than 4% for multilayer samples. In addition, this study shows the effectiveness of including a stress relaxation temperature at 500 °C during FE modeling to allow for better prediction of the low cross-layer accumulation of distortion in multilayer deposition of NAB.

Effect of hot-wire method on microstructure and mechanical properties of wire arc additive repaired superalloy

This study shows that the hot wire is an effective way to reduce the amount of undesirable Laves phase during the repair of 718Plus components, which are detrimental to the mechanical properties. The complex relationship between microstructure and hotwire was studied in detail. Five damaged components were repaired by depositing the melted 718Plus wire onto the wrought substrate using directed energy deposition-arc (DED-arc). A finite element model was used to provide clues for the thermal process analysis. The hot-wire method enhanced the cooling rate of the molten pool and suppressed the remelting behaviour of secondary dendritic arms (SDA) in the reheated zone. The resultant microstructure contained refined dendrites with more obvious SDA, which allows the production of tiny reticular Nb-rich liquid spots between dendrites during final solidification stage. These spots beyond a threshold of Nb could cause eutectic reaction, leading to the morphologic transformation from long-stripped to granular Laves phase and a lower volume fraction. Moreover, the hot-wire method hindered the dynamic precipitation of γ' phase due to the shortened precipitation time, which was responsible for the inferior mechanical properties. The heat-treatment re-optimized the precipitation of γ' phase and further dissolved Laves phase to release more Nb for γ' phase, which leads to the improvement of strength about 10 %.

Wearable Applicability of Respiratory Airflow Transducers: Current Approaches and Future Directions.

Advanced technologies employed in modern respiratory airflow transducers have exhibited powerful capabilities in accurately measuring respiratory flow under controlled and sedentary conditions, particularly in clinical settings. However, the wearable applicability of these transducers as face-mounted electronics for use in occupational and sporting activities remains unexplored. The present review addresses the critical wearability issue associated with current respiratory airflow transducers, including pneumotachographs, orifice flowmeters, turbine flowmeters, hot wire anemometers, ultrasound flowmeters, and piezoelectric airflow transducers. Furthermore, a comprehensive analysis and comparison of all factors that impact the wearable applicability of respiratory airflow transducers are conducted, considering dynamic accuracy, long-term usability, power consumption, calibration frequency, and cleaning requirements. The findings indicate that the piezoelectric airflow transducer stands out as a more viable option for wearables compared to other devices. We expect that this review will serve as a valuable engineering reference, guiding future research efforts in designing and developing wearable respiratory airflow transducers for ambulatory respiratory flow monitoring.

A simple hot wire temperature drift correction based on temperature sensitivity applied to a turbulent shear layer

A procedure is proposed to correct temperature drift for hot wire anemometry measurements in turbulent fields where the facility is not equipped with temperature control. The procedure consists of evaluating the wire sensitivity to the temperature by building a voltage-temperature curve. The voltages of both the calibration points and the measurement points are corrected, shifting the voltage values to an arbitrary reference temperature. The correction can be applied to the instantaneous voltages by performing synced temperature measurements with constant current anemometry or constant voltage anemometry cold wire. The efficacy of the method is tested on a turbulent shear layer that develops on the side of an open jet wind tunnel not equipped with temperature control. The velocity statistics show a good match with respect to reference particle image velocimetry measurements, evidencing the self-similarity of the shear layer in contrast with the non-corrected data and the data corrected using the semi-empirical and analytical relation based on King's law modification. A correction based only on the temperature statistics shows indistinguishable results with respect to the instantaneous correction.

Lagrangian particle tracking at large Reynolds numbers.

In the study of fluid turbulence, the Lagrangian frame of reference represents the most appropriate methodology for investigating transport and mixing. This necessitates the tracking of particles advected by the flow over space and time at high resolution. In the past, the purely spatial counterpart, the Eulerian frame of reference, has been the subject of extensive investigation utilizing hot wire anemometry that employs Taylor's frozen flow hypotheses. Measurements were reported for Taylor scale Reynolds number Rλ > 104 in atmospheric flows, which represent the highest strength of turbulence observed on Earth. The inherent difficulties in accurately tracking particles in turbulent flows have thus far constrained Lagrangian measurements to Taylor scale Reynolds numbers up to approximately Rλ = 103. This study presents the Lagrangian particle tracking setup in the MaxPlanck Variable Density Turbulence Tunnel (VDTT), where Taylor scale Reynolds numbers between 100 and 6000 can be reached. It provides a comprehensive account of the imaging setup within the pressurized facility, the laser illumination, the particles used, and the particle seeding mechanism employed, as well as a detailed description of the experimental procedure. The suitability of KOBO Cellulobeads D-10 particles as tracers within the VDTT is illustrated. The results demonstrate that there is no significant charge exhibited by the particles and that the impact of their inertia on the results is negligible across a wide range of experimental conditions. Typical data are presented, and the challenges and constraints of the experimental approach are discussed in detail.

Micro-explosion-induced combustion and agglomeration characteristics in composite propellants with fluorinated graphene

The potential of the Al-F reaction in suppressing agglomeration during propellant combustion and enhancing combustion performance is investigated by introducing fluorinated graphene as a fluorinated oxidizer. Comparative analyses of ignition combustion and agglomeration behaviors are conducted on novel composite powders and propellant samples modified with varying contents of fluorinated graphene using laser and hot wire ignition visualization systems. Characterizing parameters such as characteristic spectra, flame grayscale, ignition delay time, combustion duration, and burning rate are measured during combustion at different pressures. Additionally, agglomerated particles are collected via quenching techniques under 7 MPa pressure to explore the influence mechanism of fluorinated graphene on agglomeration near the burning surface, and a comprehensive influence mechanism is proposed. Results indicate that fluorinated graphene promotes ammonium perchlorate decomposition, accelerates oxidizing gas release, and enhances thermal conduction at the burning surface. The reaction between Al and F decreases the formation of intermediates (AlO and Al2O), while the interaction of F with Al and Al2O3 effectively inhibits the clustering of Al particles, replacing conventional oxidation reactions and resulting in a unique micro-explosion jetting phenomenon. The introduction of 15 % fluorinated graphene concentrates most product particles around 10 μm, enhancing energy release during combustion. Overall, this composite powder containing fluorinated graphene effectively improves the combustion performance of aluminum-containing composite propellants, inhibiting Al particle agglomeration and potentially reducing specific impulse loss in solid rocket motors.

Inspection, Testing and Examination System at Gangsa 2 Laboratory at Uitm Bukit Besi

Examination and testing of the (LEV) system was conducted at the Gangsa 2 laboratory of (UiTM) Kampus Bukit Besi to evaluate performance and compliance with safety standards. The inspection aimed to obtain data on airflow, static pressure, and velocities at key points in the LEV system, focusing on a single fume hood (FH-GANGSA 2). Methodology followed guidelines from the (ACGIH) and adhered to (USECHH) 2000 Regulations. Face velocities were measured at different sash heights, and duct transport velocities were assessed. Smoke tests were performed to visually evaluate containment efficiency. Instruments used included a hot wire anemometer, pitot tube, digital manometer, and smoke tester kit. Results showed the fume hood had an average face velocity of 117.8 fpm at the recommended working height of 19.7 inches, within the 80-100 fpm range specified by ACGIH. Duct transport velocity was 3102 fpm, exceeding the recommended 1000-2000 fpm range. The smoke test demonstrated excellent containment with smooth inflow and no escape of smoke outside the hood. A comparison with the previous year's inspection revealed a slight decrease in performance, with face velocity dropping from 109 fpm to 88.5 fpm. While for the flowrate, there is a notable increase in the flow rate from 2023 to 2024. The LEV system was found to meet acceptable working conditions based on ACGIH standards and comply with (USECHH) 2000 Regulations. Recommendations included designing the system by a registered professional engineer as stipulated in (USECHH) Regulation 2000, continuing monthly performance monitoring, and improving accessibility to the centrifugal fan for more comprehensive measurements. This examination helps establish baseline measurements for ongoing monitoring of the LEV system's effectiveness in protecting worker health and safety in laboratory settings.

Influence of printing parameters on the mechanical behavior of 3D-printed SS316L parts manufactured using laser hot wire directed energy deposition

Hybrid manufacturing combines the simultaneous benefits of additive manufacturing (complex geometries, part consolidation, and mass customization) with the advantages of subtractive manufacturing (superior surface finish and enhanced dimensional accuracies) by integrating a suite of complementary traditional processes into a base platform of additive manufacturing. The use of hybrid technology has grown in recent years given its capabilities on repairing metallic structures, producing parts with conformal cooling features, and manufacturing functionally graded products. These kinds of capabilities are of great interest to the medical implant, energy, automotive, maritime, and aerospace industry sectors, among many other fields. This work investigated the mechanical properties of stainless steel (SS) 316L as a function of different tool paths strategies using an integrated 5-axis CNC hybrid Mazak system with a laser hot wire deposition system (LHWDS). This study includes the evaluation of different printing parameters and their impact on the quality of the printed bead as well as the incorporation of a structure–property material relationship based on the mechanical performance of the manufactured coupons.

Estimation of heat source, specific heat, and thermal conductivity of insulation materials using modified conjugate gradient method

The use of insulation materials is crucial for minimizing thermal losses in various industries like automotive, building, solar, and aerospace. Plexiglass and Expanded Polystyrene (EPS) foam are popular choices due to their effective temperature regulation, lightweight nature, and cost-effectiveness. Accurate measurement of their thermal properties is vital for achieving conservation goals. While the parallel hot wire technique provides valuable insights, accurately determining heat source strength (HW) poses a challenge, impacting measurement accuracy. To address this, the modified Conjugate Gradient Method (CGM) is employed for simultaneous estimation of thermal conductivity (λ), specific heat (c) and HW of Plexiglass and EPS foam. The direct problem result has been validated with published experimental work that shows deviations less than 2 %. The study investigates the impact of sensor positioning relative to the hot-wire (rm) and introduces artificial Gaussian error with standard deviations (θ) of 0.01 °C, 0.02 °C and 0.1 °C. At θ = 0.1 °C the percentage relative errors in the estimation of λ, c and HW with rm = 5 mm for Plexiglass are 5 %, 1.442 %, and 4.651 % respectively. For EPS foam the corresponding errors are 2.44 %, 1.26 %, and 1.74 %. The modified CGM emerges as a reliable algorithm for the measurement of thermal properties of insulation materials.

Microstructural analysis and mechanical characterization of dissimilar welds between nickel-based and steel-based superalloys post-cryogenic treatment using hotwire GTAW

This study explores the dissimilar welding of nickel superalloy 59 with Fe-Ni superalloy 904 L using the Gas Tungsten Arc Welding with Hot Wire technique (HW-GTAW). The HW-GTAW process produced defect-free weldments with complete penetration, as confirmed by macroscopic analysis. Microstructural analysis using FESEM and EDS revealed fine equiaxed and columnar dendrites in the fusion zone and identified a secondary phase enriched with chromium. XRD analysis supported the presence of predominant austenitic phases and indicated the formation of Cr23C6-type carbide. The grain size of the weld joint, determined using the Gaussian method and Scherer formula, was 44.53 nm, slightly smaller than base metals. Microhardness tests revealed values ranging from 226 ± 5 HV 10 to 243 ± 5 HV 10, with the highest values observed in the deep cryogenic treatment (DCT). The Mo in the ERNiCrMo-13 filler and the effects of DCT, which promote grain refinement, are responsible for this increase in hardness. Residual stress measurements revealed a maximum tensile stress of 315 MPa along the longitudinal axis and a maximum compressive stress of 355 MPa along the transverse axis. DCT enhanced the weldment’s tensile strength by up to 12% compared to as-welded samples, with a 6% increase compared to shallow cryogenic-treated (SCT) samples. Charpy impact testing indicated a value of 88 J in the fusion zone, which is 1.2% less than alloy 59 and 9% higher than 904 L. Tensile fracture analysis revealed ductile dimples, while impact fractography showed a mix of ductile dimples and brittle, glassy cleavage facets.