High Principal Strain Research Articles

The Effect of Stiffness on Friction, Surface Strain and Contact Area of a Sliding Finger Pad Simulant

This study investigates the frictional and surface strain behaviour of silicone hemispherical finger pad simulants with different stiffness during tribological interactions with a smooth glass plate. A novel contact area and strain measurement method employing a digital image correlation technique was employed to give new understanding of the pad behaviour during sliding. The frictional behaviour of the sliding finger pad simulant is dominated by the adhesion mechanism, with a small overall contribution from deformation, as suggested by the high principal strains at the edge of the contact area. The strain behaviour is also influenced by the magnitude of the normal force and the stiffness of the samples.

Thermo-Structural Analysis of Carbon Fibre-Ni Based Super Alloy Composite Employed in Gas Turbines

A computational analysis was carried out on two different materials of turbine blades, namely Inconel MA754 and Nimonic 80A, in order to determine their structural and thermal properties at elevated temperatures. Long carbon fibers of uniform length were used and deposited at varying thicknesses ranging from 1 mm to 4 mm, on the top surface of turbine blades and then analyzed for its performance. It is seen that the carbon fibers (IM10) embedded in the super alloys drastically improve the load bearing parameters of the configurations being analyzed. The improvement in structural load carrying ability is a result of higher Young's modulus primarily. Subsequent analysis with higher volume fraction of the fibers indicated saturation of performance at about 70 % volume fraction for 4 mm fibers and significant improvement beyond it for the 1 mm fibers. With improvement in the load bearing characteristics the blade with fibers embedded into a tube like structure at 3 sections were configured and A thermal analysis of the same underscores the effectiveness of the 4 mm fibers in undergoing much reduced principal strains than other configurations. This is seen to be a result of insulation of the top surface from increase in temperature, which significantly reduces the thermal expansion, especially at the free end. This is in contrast to other configurations, where the low volume fraction of fibers resulted in high principal strain.

Thermo-Structural Analysis of Carbon Fibre-Ni Based Super Alloy Composite Employed in Gas Turbines

A computational analysis was carried out on two different materials of turbine blades, namely Inconel MA754 and Nimonic 80A, in order to determine their structural and thermal properties at elevated temperatures. Long carbon fibers of uniform length were used and deposited at varying thicknesses ranging from 1 mm to 4 mm, on the top surface of turbine blades and then analyzed for its performance. It is seen that the carbon fibers (IM10) embedded in the super alloys drastically improve the load bearing parameters of the configurations being analyzed. The improvement in structural load carrying ability is a result of higher Young's modulus primarily. Subsequent analysis with higher volume fraction of the fibers indicated saturation of performance at about 70% volume fraction for 4 mm fibers and significant improvement beyond it for the 1 mm fibers. With improvement in the load bearing characteristics the blade with fibers embedded into a tube like structure at 3 sections were configured and A thermal analysis of the same underscores the effectiveness of the 4 mm fibers in undergoing much reduced principal strains than other configurations. This is seen to be a result of insulation of the top surface from increase in temperature, which significantly reduces the thermal expansion, especially at the free end. This is in contrast to other configurations, where the low volume fraction of fibers resulted in high principal strain.

Differential effects of altered patterns of movement and strain on joint cell behaviour and skeletal morphogenesis

SummaryObjectiveThere is increasing evidence that joint shape is a potent predictor of osteoarthritis (OA) risk; yet the cellular events underpinning joint morphogenesis remain unclear. We sought to develop a genetically tractable animal model to study the events controlling joint morphogenesis.DesignZebrafish larvae were subjected to periods of flaccid paralysis, rigid paralysis or hyperactivity. Immunohistochemistry and transgenic reporters were used to monitor changes to muscle and cartilage. Finite Element Models were generated to investigate the mechanical conditions of rigid paralysis. Principal component analysis was used to test variations in skeletal morphology and metrics for shape, orientation and size were applied to describe cell behaviour.ResultsWe show that flaccid and rigid paralysis and hypermobility affect cartilage element and joint shape. We describe differences between flaccid and rigid paralysis in regions showing high principal strain upon muscle contraction. We identify that altered shape and high strain occur in regions of cell differentiation and we show statistically significant changes to cell maturity occur in these regions in paralysed and hypermobile zebrafish.ConclusionWhile flaccid and rigid paralysis and hypermobility affect skeletal morphogenesis they do so in subtly different ways. We show that some cartilage regions are unaffected in conditions such as rigid paralysis where static force is applied, whereas joint morphogenesis is perturbed by both flaccid and rigid paralysis; suggesting that joints require dynamic movement for accurate morphogenesis. A better understanding of how biomechanics impacts skeletal cell behaviour will improve our understanding of how foetal mechanics shape the developing joint.

Mechanical Interaction of an Expanding Coiled Stent with a Plaque-Containing Arterial Wall: A Finite Element Analysis.

Wall injury is observed during stent expansion within atherosclerotic arteries, related in part to stimulation of the inflammatory process. Wall stress and strain induced by stent expansion can be closely examined by finite element analysis (FEA), thus shedding light on procedure-induced sources of inflammation. The purpose of this work was to use FEA to examine the interaction of a coiled polymer stent with a plaque-containing arterial wall during stent expansion. An asymmetric fibrotic plaque-containing arterial wall model was created from intravascular ultrasound (IVUS) images of a diseased artery. A 3D model for a coil stent at unexpanded state was generated in SolidWorks. They were imported into ANSYS for FEA of combined stent expansion and fibrotic plaque-distortion. We simulated the stent expansion in the plaqued lumen by increasing balloon pressure from 0 to 12atm in 1atm step. At increasing pressure, we examined how the expanding stent exerts forces on the fibrotic plaque and vascular wall components, and how the latter collectively resist and balance the expansive forces from the stent. Results show the expanding coiled stent creates high stresses within the plaque and the surrounding fibrotic capsule. Lower stresses were observed in adjacent medial and adventitial layers. High principal strains were observed in plaque and fibrotic capsule. The results suggest fibrotic capsule rupture might occur at localized regions. The FEA/IVUS method can be adapted for routine examination of the effects of the expansion of selected furled stents against IVUS-reconstructed diseased vessels, to improve stent deployment practices.

Validation experiments on finite element models of an ostrich (Struthio camelus) cranium.

The first finite element (FE) validation of a complete avian cranium was performed on an extant palaeognath, the ostrich (Struthio camelus). Ex-vivo strains were collected from the cranial bone and rhamphotheca. These experimental strains were then compared to convergence tested, specimen-specific finite element (FE) models. The FE models contained segmented cortical and trabecular bone, sutures and the keratinous rhamphotheca as identified from micro-CT scan data. Each of these individual materials was assigned isotropic material properties either from the literature or from nanoindentation, and the FE models compared to the ex-vivo results. The FE models generally replicate the location of peak strains and reflect the correct mode of deformation in the rostral region. The models are too stiff in regions of experimentally recorded high strain and too elastic in regions of low experimentally recorded low strain. The mode of deformation in the low strain neurocranial region is not replicated by the FE models, and although the models replicate strain orientations to within 10° in some regions, in most regions the correlation is not strong. Cranial sutures, as has previously been found in other taxa, are important for modifying both strain magnitude and strain patterns across the entire skull, but especially between opposing the sutural junctions. Experimentally, we find that the strains on the surface of the rhamphotheca are much lower than those found on nearby bone. The FE models produce much higher principal strains despite similar strain ratios across the entirety of the rhamphotheca. This study emphasises the importance of attempting to validate FE models, modelling sutures and rhamphothecae in birds, and shows that whilst location of peak strain and patterns of deformation can be modelled, replicating experimental data in digital models of avian crania remains problematic.

Resonance in the mouse tibia as a predictor of frequencies and locations of loading-induced bone formation

To enhance new bone formation for the treating of patients with osteopenia and osteoporosis, various mechanical loading regimens have been developed. Although a wide spectrum of loading frequencies is proposed in those regimens, a potential linkage between loading frequencies and locations of loading-induced bone formation is not well understood. In this study, we addressed a question: Does mechanical resonance play a role in frequency-dependent bone formation? If so, can the locations of enhanced bone formation be predicted through the modes of vibration? Our hypothesis is that mechanical loads applied at a frequency near the resonant frequencies enhance bone formation, specifically in areas that experience high principal strains. To test the hypothesis, we conducted axial tibia loading using low, medium, or high frequency to the mouse tibia, as well as finite element analysis. The experimental data demonstrated dependence of the maximum bone formation on location and frequency of loading. Samples loaded with the low-frequency waveform exhibited peak enhancement of bone formation in the proximal tibia, while the high-frequency waveform offered the greatest enhancement in the midshaft and distal sections. Furthermore, the observed dependence on loading frequencies was correlated to the principal strains in the first five resonance modes at 8.0-42.9 Hz. Collectively, the results suggest that resonance is a contributor to the frequencies and locations of maximum bone formation. Further investigation of the observed effects of resonance may lead to the prescribing of personalized mechanical loading treatments.

Biomechanical responses of a pig head under blast loading: a computational simulation

A series of computational studies were performed to investigate the biomechanical responses of the pig head under a specific shock tube environment. A finite element model of the head of a 50-kg Yorkshire pig was developed with sufficient details, based on the Lagrangian formulation, and a shock tube model was developed using the multimaterial arbitrary Lagrangian-Eulerian (MMALE) approach. These two models were integrated and a fluid/solid coupling algorithm was used to simulate the interaction of the shock wave with the pig's head. The finite element model-predicted incident and intracranial pressure traces were in reasonable agreement with those obtained experimentally. Using the verified numerical model of the shock tube and pig head, further investigations were carried out to study the spatial and temporal distributions of pressure, shear stress, and principal strain within the head. Pressure enhancement was found in the skull, which is believed to be caused by shock wave reflection at the interface of the materials with distinct wave impedances. Brain tissue has a shock attenuation effect and larger pressures were observed in the frontal and occipital regions, suggesting a greater possibility of coup and contrecoup contusion. Shear stresses in the brain and deflection in the skull remained at a low level. Higher principal strains were observed in the brain near the foramen magnum, suggesting that there is a greater chance of cellular or vascular injuries in the brainstem region.