Higher Average Density Research Articles

Stand Dynamics of Non-Wood Forest Product Species in the Kuinima Classified Forest (KCF) in the Houet Province (Burkina Faso)

The vegetation cover of forest ecosystems in sub-Saharan Africa is currently deteriorating. Species that provide non-wood forest products such as Vitellaria paradoxa, Parkia biglobosa and Adansonia digitata are not spared. The aim of this study is to contribute to the valorization and conservation of these species. To achieve this, a forest inventory of the main species was conducted in the Kuinima classified forest. A systematic inventory was carried out using circular plots with a radius of 20 cm. The data obtained was complemented by a structural study of these formations, based on the circumference measured at 1m 30 from the ground. ANOVA analysis of variance revealed a significant difference between densities. The results show that Vitellaria paradoxa has the highest average density (47.714±65.165 individuals/ha), followed by Parkia biglobosa (5.626±2.29 individuals/ha). In terms of health condition, Vitellaria paradoxa is the most attacked by Loranthaceae (41.93%). Regarding the stand structure, all three species show an abundance of juvenile trees (c ≤20 cm). Moreover, with the low mortality rates observed, the dynamics is evolutionary for all three species. In order to preserve the wood potential of this forest, capacity building, technical and awareness-raising actions could be undertaken. These results constitute data that should be taken into account in programs for the conservation of NWFP species in general, and for the control of Loranthaceae that parasitize Vitellaria paradoxa in particular.

Al-doped Li4SiO4 for cyclic solar energy storage and CO2 capture: An experimental and DFT study

The substantial consumption of fossil fuels gives rise to excessive carbon dioxide emissions, and mitigating them has emerged as a pressing global priority. The use of renewable energy and carbon capture, utilization, and storage are recognized as two major approaches for carbon neutrality. Li4SiO4 materials exhibit promising prospects in both thermochemical heat storage for solar energy power and cyclic high-temperature CO2 capture. The reactivity between Li4SiO4 and CO2 plays the vital role in its energy storage and CO2 capture performance. Herein, we prepare Al-doped Li4SiO4 materials through an impregnated suspension technique, simultaneously achieving high contact areas and lattice defects to enhance both fast chemisorption and ion diffusion processes. The results show that Al-doped Li4SiO4 exhibits high average energy density of 56677.08 kJ/kmol within 30 cycles. Additionally, the granulated Al-doped Li4SiO4-based pellets, produced via the freeze-drying technique, exhibit negligible energy density loss rate of less than 9 % and acceptable mechanical strength. Furthermore, the CO2 sorption performance also reaches a high value of 0.27 g/g. The reaction mechanism between Li4SiO4 and CO2 has been investigated at both macroscopic and microscopic levels through kinetic analysis and DFT calculations. The simulated Al-doped Li4SiO4/CO2 sorption system possesses increased adsorption energy level from −0.81 eV for the undoped one to −0.95 eV, thereby leading to the improved CO2 sorption. In general, Al-doped Li4SiO4 materials demonstrate great potential for applications in thermochemical heat storage and CO2 capture.

Population status and host fishes of the freshwater pearl mussel in the eastern part of the Onega Peninsula, Northern European Russia

Four populations of freshwater pearl mussel Margaritifera margaritifera were studied at lower sections of three river basins of the eastern part of the Onega Peninsula, Northern European Russia: the Bol’shaya Syarta, the Ust’-Yaren’ga and the Lopshen’ga (including Kamenny Stream). One of the populations from the Lopshen’ga River was discovered for the first time. Here we present preliminary data on the population status of M. margaritifera, its host fishes and glochidia infestation in the studied river basins. Living juvenile mussels and fishes infested by glochidia were recorded only in two waterbodies, i.e., the Bol’shaya Syarta and Ust’-Yaren’ga rivers. The pearl mussel population from the Bol’shaya Syarta River seems to represent the most prosperous among studied ones. The average density of visible mussels was small in the lower section of the river, but the proportion of young mussels was rather high (33.1 %) and intensity of glochidia infection reached 865 glochidia per fish. The highest average density was recorded in the pearl mussel population from the Kamenny Stream, Lopshen’ga River basin. However, only one juvenile mussel and none of host fishes infested by glochidia were recorded in this watercourse that may indicate the population aging and decrease of reproduction. Morphological analyses revealed significant differences between four studied populations of M. margaritifera towards the shell convexity index (SCI) and shell elongation index (SEI). In all studied basins, salmonid fishes were also infested by other parasites, mainly flatworms and their cysts. This factor may negatively impact the salmonid host fish populations that require monitoring of the current situation. The data obtained and future studies will allow to develop a system for protecting and monitoring of populations of a rare species such as the freshwater pearl mussel M. margaritifera.

Charge Accumulation Effect Enabled by a Bioinspired Self‐lubricating Triboelectric Nanogenerator for Both High Average Power Density and Long Durability

AbstractRecently through the synergetic utilization of triboelectrification, electrostatic induction, and electrostatic discharge, a novel dual‐functional triboelectric nanogenerator (DF‐TENG) has been developed, which can not only generate a motion‐responsible alternating current/ direct current output but also provide a higher performance compared to traditional TENGs. However, further improvements in performance and lifespan are crucial and remain challenging for the future large‐scale application of this new‐type TENG. Herein, a novel bioinspired self‐lubricating prototype is presented (BS‐TENG), which employs a porous polyurethane (PU) matrix impregnated with a low‐viscosity dielectric lubricant. In response to external mechanical stimuli, the BS‐TENG can “secrete” pre‐stored lubricant to partially fill micro‐gaps between tribo‐layers, thus forming self‐lubrication. This self‐lubricating mechanism not only elevates the electrostatic discharge threshold between tribo‐layers to maximize charge accumulation, thereby facilitating efficient energy release through electrostatic discharge for enhanced power output, but also significantly reduces material abrasion and realizes superior output durability. Benefiting from this effect, the BS‐TENG delivers an average power density of up to 4.6 W m−2, with extraordinary stability to retain 99% of its initial output even after over 60 000 cycles. This work provides a straightforward and effective strategy for realizing high‐performance and long‐stability TENGs, paving the way for their practical applications.

Recent advances in high charge density triboelectric nanogenerators

Abstract Triboelectric materials with high charge density are the building-block for the commercial application of triboelectric nanogenerators (TENGs). Unstable dynamic processes influence the change of the charge density on the surface and inside of triboelectric materials. The charge density of triboelectric materials depends on the surface and the internal charge transfer processes. The focus of this review is on recent advances in high charge density triboelectric materials and advances in the fabrication of TENGs. We summarize the existing strategies for achieving high charge density in triboelectric materials as well as their fundamental properties. We then review current optimization methods for regulating dynamic charge transfer processes to increase the output charge density: first, increasing charge injection and limiting charge dissipation to achieve a high average surface charge density, and second, regulating the internal charge transfer process and storing charge in triboelectric materials to increase the output charge density. Finally, we present the challenges and prospects in developing high-performance triboelectric materials.

Transport of Floating Plastics through the Fluvial Vector: The Impact of Riparian Zones

This study presents results from an experimental campaign to explore how different riparian zone characteristics may facilitate the transport or capturing of plastics floating through the fluvial system. Specifically, following field observations for the transport of plastics through fluvial vectors, a substantial number of flume experiments has been designed to assess the effect of floating macro-plastics and riparian zone characteristics. The results from flume experiments were analyzed using particle tracking velocimetry techniques to derive transport metrics (such as transport velocities) of macro-plastics of different sizes and shapes, released at five locations across a wide channel with distinct distance from the vegetated riverbank. The findings are discussed while considering the trapping mechanisms along the vegetated riverbank, which include a range of vegetation densities and arrangements, aiming to identify and quantify the degree of impact of each of the control parameters on the transport of floating plastics. The flow velocimetry records obtained at locations near and within the riverbank correlate well with the transport velocities of the floating plastics. Macro-plastic litter carried downstream away from the riverbank can have up to nine times the transport velocity, compared to those found within the riverbank. The change from a low to a high average density can result in about three times decrease in the transport velocity of floating macro-plastic litter within the riparian zone. These outcomes can help inform better practices for the management of riparian vegetation to maximize the trapping efficiency of macro-plastics, adapted to different flow conditions and river morphologies.

Explore the growth mechanism of high-quality diamond under high average power density in the MPCVD reactor

Investigating the mechanism behind the high-efficiency deposition of high-quality diamond has always been a prominent topic in related research. This paper investigates the CH4-H2 plasma characteristics and related chemical reaction kinetics in the average power density range of 18–100 W·cm−3, which is a typical range for large-area diamond film deposition. The number densities of H, CH3 and C2H2 increase linearly with the average power density. C2H2 is the main hydrocarbon in the discharge, and CH3 is the main single-carbon hydrocarbon. The number density and radial uniformity of CH3 and C2H2 increase with the average power density, which is necessary for the high rate and uniform deposition of diamond films. The plasma's optical emission spectra indicate an acceleration in the C2 production rate at high power density. The diamond film deposition experiment demonstrates the efficacy of high average power density in achieving high-quality diamond deposition at a high growth rate.

State of the Siberian sturgeon population in the Middle Lena in summer

The purpose: to obtain modern data on the distribution, abundance, size composition and biological state of the sturgeon in the middle reaches of the Lena River.Material: data of scientific accounting survey using bottom drift nets in summer 2022.The results: Siberien sturgeon is dstributed irregularly on a 400‑kilometer stretch of the river from the city of Yakutsk to the Vilyui River, with the highest average density near the Vilyui River mouth 163 ind./km2, while sturgeon densities in the areas of Yakutsk and the Aldan River mouth were 71 and 44 ind./km2 respectively. The highest density of fish with the smallest average size in the area near the Vilyui mouth indirectly indicates the presence of a separate herd in the Vilyui River. The average density of fish over the entire 400‑km area was 93 ind./km2. The sturgeon length to the end of the middle rays (ac) was from 21 to 86 cm; on average 43.4 ± 10.7 cm. The modal size class for the sturgeon in catches in 2022 was 41–50 cm (44% of the total catch). The fish weight ranged from 40 to 3800 g. The average weight of individuals was 0.557. More than 80% of fish from all catches weighed up to 700 g. The weight of fish with a length ac 62–71 cm ranged from 0,400 to 1.415 kg, on average 1.0 kg. There were only 2.5% of commercial individuals in the total harvest. Sexually mature females were noted only near the Aldan mouth, where their share was 11% that may indicate the presence of spawning grounds in its channel. In the sample of fish that underwent a complete biological analysis (one third of the catches), sexually mature males were not observed. Estimated number of sturgeon: in Yakutsk city area — 17000 ind., in the Aldan mouth area — 47000 ind., in the Vilyui mouth area — 55000 ind. The total number of Siberian sturgeon on a 400‑kilometer stretch of the Lena River was at least 120000 ind. The state and structure of sturgeon population corresponds to the average statistical retrospective data.Practical value: the results obtained will improve the efficiency of assessing the distribution and stock of sturgeon in the Lena River.

Effects of electron irradiation on graphene drums

Using a scanning electron microscope, we irradiate graphene drums with electrons at an energy of 20 keV and a dosage of about 1.58 × 1017 electrons/cm2. The drums consist of graphene exfoliated in ambient air over holes having a diameter of 4.6 μm and etched into an SiO2 substrate. After irradiation, we observe that the drum’s suspended monolayer (ML) region has a ratio of the Raman D peak height, ID, to the Raman G peak height, IG, as high as 6.3. In contrast, the supported ML on the SiO2 substrate has an ID/IG ratio of 0.49. Previous studies have shown that graphene drums containing air can leak in a vacuum at a low rate. We attribute the high ID/IG ratio of the suspended ML to the air that may be in the drums. We propose that the air produces much adsorbed water on the ML, resulting in a high average defect density during irradiation. We present Raman maps of the full-width-at-half maximum, position, and height of the G, 2D, D, and D’ peaks before and after irradiation and maps of ID/IG and ID/ID’. We anneal the drums at temperatures from 50 to 215 °C and find that ID/IG significantly reduces to 0.42. The annealing data are analyzed using an Arrhenius plot. We also find that ID/ID’ depends on annealing temperature and has values ≥8, in the range expected for sp3 defects, for ID/IG ≤ 3.9. This irradiation method may help achieve high average defect densities in ML graphene, imparting novel and potentially valuable properties.

STRENGTH OF CONCRETE FOR BASES OF ROAD CLOTHES ON DIFFERENT TYPES OF SECONDARY GRAVEL AND SAND

The task of developing of concrete for the bases of road clothing using secondary concrete aggregates is relevant for an economic and ecological reasons. The properties of concrete were compared with different types of coarse aggregate of 8-16 mm fraction: granite river gravel, secondary crushed stone from recycled reinforced concrete structures, secondary crushed stone from recycled brickwork and ceramic tiles. Three types of sand with a fraction of 0-4 mm were also used: quartz, secondary sand from recycled reinforced concrete structures, secondary sand from recycled brickwork. 2 series of experiments were conducted. During the first series of experiments Portland cement CEM II/B-S 32.5 R and superplasticizer Soudal Soudaplast was used (1% from weight of cement). For the second series of experiments Portland cement CEM II/B-S 42.5 R and superplasticizer Berament HT28 was used (1.2% from weight of cement). The mobility of all mixtures was equal to S1. Concretes with Berament HT28 superplasticizer had a lower W/C ratio of mixture than concretes with similar aggregates composition and Soudal Soudaplast superplasticizer. The use of secondary crushed stone requires an increasing of the W/C ratio of the mixture. The simultaneous use of secondary sand additionally increases W/C. Due to the lower W/C, the concretes of the second series have a higher average density than the similar concretes of the first series of the experiment. Concretes based on granite gravel and quartz sand have the highest average density (2369-2465 kg/m3). When using secondary crushed stone from reinforced concrete structures, the average density decreases by 3-5%. When using secondary crushed stone from brickwork and ceramic tiles – decreases by 8-9%. Concretes based on secondary crushed stone and sand from reinforced concrete structures have a 6-9% lower average density compared to concretes on granite gravel. Concretes based on secondary crushed stone and sand from recycled brickwork and ceramic tiles have the lowest average density – from 2015 to 2061 kg/m3. Due to the use of higher grade cement and a more effective superplasticizer, the strength of the concretes of the second series of the experiment at the age of 3 days was 69-190% higher than the strength of similar concretes of the first series, at the age of 28 days – higher by 67 to 147%. When using quartz sand, concrete based on secondary crushed stone from reinforced concrete structures has the greatest strength. At the age of 3 days up to 17.97 MPa and 30.33 MPa, at the design age (28 days) up to 32.07 and 53.41 MPa for the first and second series, respectively. The lowest strength (about 16 MPa in the first series of experiments and 27 MPa in the second) had concretes using only low-strength secondary aggregates from recycled brickwork and ceramic tiles. In general, all the studied concretes on secondary aggregates were characterized by sufficient strength for their use in the bases of hard road clothes.

Bulk Tungsten Fiber-Reinforced Tungsten (Wf/W) Composites Using Yarn-Based Textile Preforms

The use of tungsten fiber-reinforced tungsten composites (Wf/W) has been demonstrated to significantly enhance the mechanical properties of tungsten (W) by incorporating W-fibers into the W-matrix. However, prior research has been restricted by the usage of single fiber-based textile fabrics, consisting of 150 µm warp and 50 µm weft filaments, with limited homogeneity, reproducibility, and mechanical properties in bulk structures due to the rigidity of the 150 µm W-fibers. To overcome this limitation, two novel textile preforms were developed utilizing radial braided W-yarns with 7 core and 16 sleeve filaments (R.B. 16 + 7), with a diameter of 25 µm each, as the warp material. In this study, bulk composites of two different fabric types were produced via a layer-by-layer CVD process, utilizing single 50 µm filaments (type 1) and R.B. 16 + 7 yarns (type 2) as weft materials. The produced composites were sectioned into KLST-type specimens based on DIN EN ISO 179-1:2000 using electrical discharge machining (EDM) and subjected to three-point bending tests. Both composites demonstrated enhanced mechanical properties with pseudo-ductile behavior at room temperature and withstood over 10,000 load cycles between 50–90% of their respective maximum load without sample fracture in three-point cyclic loading tests. Furthermore, a novel approach to predict the fatigue behavior of the material under cyclic loading was developed based on the high reproducibility of the composites produced, especially for the composite based on type 1. This approach provides a new benchmark for upscaling endeavors and may enable a better prediction of the service life of the produced components made of Wf/W in the future. In comparison, the composite based on fabric type 1 demonstrated superior results in manufacturing performance and mechanical properties. With a high relative average density (>97%), a high fiber volume fraction (14–17%), and a very homogeneous fiber distribution in the CVD-W matrix, type 1 shows a promising option to be further tested in high heat flux tests and to be potentially used as an alternative to currently used materials for the most stressed components of nuclear fusion reactors or other potential application fields such as concentrated solar power (CSP), aircraft turbines, the steel industry, quantum computing, or welding tools. Type 2 composites have a higher layer spacing compared to type 1, resulting in gaps within the matrix and less homogeneous material properties. While type 2 composites have demonstrated a notable enhancement over 150 µm fiber-based composites, they are not viable for industrial scale-up unlike type 1 composites.

Stochastic modeling of blob-like plasma filaments in the scrape-off layer: Theoretical foundation

A stochastic model for a superposition of uncorrelated pulses with a random distribution of amplitudes, sizes, and velocities is presented. The pulses are assumed to move radially with fixed shape and amplitudes decaying exponentially in time due to linear damping. The pulse velocities are taken to be time-independent but randomly distributed. The implications of a distribution of pulse amplitudes, sizes, and velocities are investigated. Closed-form expressions for the cumulants and probability density functions for the process are derived in the case of exponential pulses and a discrete uniform distribution of pulse velocities. The results describe many features of the boundary region of magnetically confined plasmas, such as high average particle densities, broad and flat radial profiles, and intermittent large-amplitude fluctuations. The stochastic model elucidates how these phenomena are related to the statistical properties of blob-like structures. In particular, the presence of fast pulses generally leads to flattened far scrape-off layer profiles and enhanced intermittency, which amplifies plasma–wall interactions.

Breeding biology of the African Pygmy Falcon: long-term variation and seasonal decline in breeding performance of an arid zone raptor

Birds of prey are apex predators and understanding their life history can serve as a valuable baseline for investigating their ecological role. Pygmy Falcons (Polihieraxsemitorquatus), Africa’s smallest diurnal raptor, have evolved to be obligate associates of Sociable Weaver (Philetairussocius) colonies throughout their southern African range. As a predator, Pygmy Falcons likely impact prey communities in this system including their host and other colony associates. However, no study has explored their breeding biology in detail using long-term data. We provide results from 10 years of data collected between 2011 and 2020. We followed 66 unique Pygmy Falcon territories and 323 breeding attempts in the Kalahari, South Africa. We explored annual variation in the population density of Pygmy Falcons and investigated between- and within-season variation in reproductive investment and output. The highest average density was recorded in 2015 and the lowest in 2019 and 2020. Our results show that the breeding occurs between early austral spring (August) and late summer (February), with a peak from September to December. The maximum and most frequent clutch size was three eggs and falcons usually initiated only one breeding attempt (but up to three) in a season. The incubation and nestling periods lasted on average 33 (±SD 4) and 37 (± 5) days, respectively. A three-egg clutch size and number of fledglings produced varied between seasons, and breeding success showed a seasonal decline across the breeding season. Falcons were 7 times less likely to lay a 3-egg clutch in 2019 than in 2011 and 2012, and breeding attempts initiated in September were 3.4 times more likely to be successful than those initiated in November. Predation accounted for 49.5% of breeding failures. Our results show significant variation in the breeding parameters of these falcons, but further studies are needed to understand what drives these variations.

Numerical analysis on the anode active thickness using quasi-three-dimensional solid oxide fuel cell model

A quasi-three-dimensional solid oxide fuel cell (SOFC) model reduces the computational cost by strategically ignoring the thinnest direction in an SOFC by incorporating a charge-transfer current density model to represent its active thickness in electrodes to represent its complex phenomenon in an electrode. Therefore, high accuracy of this charge-transfer current density model is required. The concentration loss is mathematically related to the charge-transfer current density based on the dusty-gas model together with activation and ohmic losses in this work. The numerical results from this study are validated with the experimental results. The influence of anode's thickness towards anode active thickness is studied with the anode thickness of 5, 10, 50, 100, 500 and 1000 μm. It is found that the quasi-three-dimensional SOFC model is capable of analysing SOFC with a sufficiently thick electrode. Also, a thick electrode and a high average current density result in a thin active thickness.

Silica clay (opoka) as a promising raw material for unfired wall products by compression molding

The article is devoted to the actual problem of producing unburnt wall products of compression molding with improved and high efficiency in terms of thermal and engineering properties. The article notes the relevance, attractiveness, and wide use of unburnt pressed products in modern civil engineering. The raw material composition and production technology of unburnt wall products of compression molding are described. The traditionally used aggregates for unburnt wall products of compression molding are reviewed and their properties are analyzed. High average density and high thermal conductivity are noted in these products. The objective is to improve the thermal characteristics of these products while ensuring their strength properties. For this purpose, it is proposed to introduce a porous component of siliceous rock called opoka (silica clay) into the raw material composition of products as a mineral filler. Opoka collected from three different deposits was reviewed, its characteristics given, and the raw material analyzed. It is noted that the porosity and average density of opoka depend on its deposit. The effect of porosity and average density of opoka on the average density, compressive strength, and water absorption of unburnt wall products of compression molding based on opoka with different porosities from different deposits is described. The effect of the properties of opoka on the properties of unburnt wall products of compression molding is explained. It is confirmed that the use of opoka in the production of unburnt wall products reduces the average density of the products and improves their thermal and engineering properties. The appropriateness of manufacturing large-sized hollow wall blocks based on opoka is substantiated.

Tsetse fly ecology and risk of transmission of African trypanosomes related to a protected forest area at a military base in the city of Abidjan, Côte d'Ivoire.

African trypanosomoses, whose pathogens are transmitted by tsetse flies, are a threat to animal and human health. Tsetse flies observed at the military base of the French Forces in Côte d'Ivoire (FFCI base) were probably involved in the infection and death of military working dogs. Entomological and parasitological surveys were carried out during the rainy and dry seasons using "Vavoua" traps to identify tsetse fly species, their distribution, favorable biotopes and food sources, as well as the trypanosomes they harbor. A total of 1185 Glossina palpalis palpalis tsetse flies were caught, corresponding to a high average apparent density of 2.26 tsetse/trap/day. The results showed a heterogeneous distribution of tsetse at the FFCI base, linked to more or less favorable biotopes. No significant variation in tsetse densities was observed according to the season. The overall trypanosomes infection rate according to microscopic observation was 13.5%. Polymerase chain reaction (PCR) analyses confirmed the presence of Trypanosoma vivax and T. congolense forest type, responsible for African animal trypanosomosis. Our findings suggest that there is a risk of introduction and transmission of T. brucei gambiense, responsible for human African trypanosomiasis, on the study site. This risk of transmission of African trypanosomes concerns not only the FFCI base, but also inhabited peripheral areas. Our study confirmed the need for vector control adapted to the eco-epidemiological context of the FFCI base.

Membrane Transport and Performance in the All-Aqueous Copper Thermally Regenerative Battery

Redox flow batteries are emerging as a promising method to provide grid-scale power and long-duration energy storage safely and economically. The thermally regenerative ammonia battery (TRAB) is a new redox flow battery category that can be recharged using low-grade waste heat rather than electric energy, adding further flexibility to the applicability of flow battery systems. Recently, a new TRAB with all-aqueous electroactive species (referred to as the Cuaq-TRAB), as opposed to deposition-dissolution reactions, was found to have superior energy and power densities relative to competing TRABs. The use of bromide and ammonia stabilizes for both Cu(I) and Cu(II) oxidation states, while also creating a cell potential of up to 1.0 V. The potential can be recovered by thermally separating ammonia from the electrolyte and adding it back to alternate electrolyte chambers in successive cycles. Potential improvements in overall cell performance are possible by reducing ohmic losses associated with membrane selection. However, the ideal membrane for the Cuaq-TRAB is not obvious and raises interesting transport questions relative to the dominant redox-active copper species being negatively charged in the catholyte but positively charged in the anolyte. Furthermore, membrane crossover of ammonia, a small, uncharged molecule, was previously shown to be a primary source of parasitic losses for TRABs. Therefore, we investigated how different membrane types (cation, anion, and non-selective) affected ion transport and TRAB performance. A batch symmetry cell was used to determine membrane conductivity in the Cuaq-TRAB environment and membrane diffusion coefficients of each species in the electrolytes. Flow cell experiments were also conducted to find peak power, energy density, average power during discharge, and capacity fade over successive electric charge/discharge cycles. Tradeoffs between membrane conductivity and permeability observed in the symmetry cell are manifested in flow cell results as either high peak and average power or high energy density and low capacity fade. These results expand on potential methods for controlling transport in redox flow batteries and demonstrate the potential for non-selective membranes for electrochemical energy technologies.

Seasonal Dynamics of Sand Flies (Diptera, Pshycodidae), Vectors of Cutaneous Leishmaniasis, in the City of Fez, Northern Morocco.

The infections transmitted by sand flies (Diptera, Psychodidae) pose always a real health problem due to the increasing number of cases detected each year and the annual emergence of new leishmaniasis outbreaks. This study evaluated the temporal evolution of six species of sand flies in five stations inventoried between May 2017 and April 2018, in order to determine for the first time the extent of cutaneous leishmaniasis (CL) transmission in the city of Fez. The monthly impact of Fez sand fly density has been studied using all multivariate statistical analyses, including multiple factor correspondence analysis (MCA), which were performed using XLSTAT and the version of SPSS 20.0 test. Differences between concentrations were considered significant if P < 0.05. To better study the results obtained, different ecological indices have been studied. This study showed that these vectors developed in different sectors of the city of Fez. A total of 816 sand flies were collected from five stations in the city, belonging to three species of the genus Phlebotomus (46.82%) and three species of the genus Sergentomyia (53.18%). The seasonal fluctuation of the average density followed a bimodal evolution for the three stations Dhar Richa, Ain Nokbi, and Boujloud. The stations of Ain Nokbi (0.87 ph/m2) and Dhar Richa (0.467 ph/m2) exposed the sites to a high average density with a maximum peak during August (1.965 ph/m2) and July (1.87 Ph/m2), respectively. S. minuta (44.24%), Ph. sergenti (26.96%), Ph. perniciosus (10.78%), and Ph. papatasi (9.07%) were the most qualified species. The calculated P value is above the 5% significance level, so the relative abundance of these species between study sites shows no significant difference. The period of phlebotomy activity of the genus Phlebotomus in Fez lasts seven months from May to November with a bimodal or trimodal evolution and varies according to the species or the surveyed station. The seasonal fluctuation of sand flies could be conditioned by climatic factors where the period of activity of the species coincides with the hot months (May, June, July, and August). We have observed that the temperature factor favors the prevalence of sand flies, while the difference in the relative abundance of species between the sites is related to the difference in the bioecological conditions of each site.

EPIDERMAL CHARACTERISTICS AND EPIDERMAL DERIVATIVES OF THE LEAVES OF Ipomoea pes-caprae (L.) R. Br. IN THE DEPOK BEACH AREA OF YOGYAKARTA

Depok Beach is a sandy beach that has limited vegetation because of strong winds, poor microclimate, and low availability of nutrients. One of the plants that can adapt to these extreme conditions is Ipomoea pes-caprae (L.) R. Br. One form of its adaptation to extreme environments is thickening the leaves. Other forms of adaptation can also be studied through the characteristics of the epidermis and the epidermal derivatives of the leaves, as the focus of this study. This type of research is exploratory research, including sampling, plant identification, leaf preparation using the leaf clearing method, and observing microscopic preparations. The data analysis used is descriptive quantitative. The data obtained include the characteristics of the epidermis and its derivatives in the form of stomata and trichomes. The results showed the average number of epidermal cells in the adaxial part of the leaves higher, that is equal to 54.05 ± 2.31 / 0.06 mm2. Stomata are parasitic and amphistomatic. The size of the stomata and the width of the stomatal pore on the adaxial surface of the leaf is smaller but has a higher average density, which is 5.80 ± 1.15 / 0.06 mm2. The trichomes found were of the glandular type.

Trapa natans Husk‐Derived Nanoporous Carbons as Electrode Materials for Sustainable High‐Power Microbial Fuel Cell Supercapacitor Systems

Energy, Sustainability, and Climate Change In article number 2100163 by Tzu-Yin Liu, Han-Yi Chen, and co-workers, a Trapa natans husks-derived electrode material (TNH) is used in microbial fuel cells (MFCs) with a high average power density of 5713 mW m−2. Moreover, supercapacitors (SCs) with TNH-based electrodes are used as energy storage from MFCs, exhibiting a high specific capacitance of 85 F g−1 after 1000 cycles. It is shown that TNH is a promising material in MFC-SC system.