High-speed Video Research Articles

Features of heat/mass transfer and explosive water boiling at the laser fiber tip

Experimentally, as well as using numerical simulation methods, the features of the processes of heat and mass transfer and explosive boiling of water, initiated by continuous laser radiation with λ = 1.94 μm, emerging from the tip of the laser fiber, are studied. The trajectories of the microvolume with the maximum temperature of the superheated liquid under laser heating, in which the probability of explosive boiling up is maximum, are determined. The calculations took into account changes in the density of superheated water and the dependence of the absorption coefficient of laser radiation on temperature. Using acoustic methods and high-speed video recording, it is shown that during explosive boiling up, the duration of the leading front of the acoustic signal is ∼300 ns. Such a long duration of pressure rise at the receiving point is explained by the fact that explosive boiling occurs in a wide area of superheated liquid near fiber tip, when the nuclei located in it are stimulated by an initially arising pressure pulse.

Secondary ice production – no evidence of efficient rime-splintering mechanism

Abstract. Mixed-phase clouds are essential for Earth’s weather and climate system. Ice multiplication via secondary ice production (SIP) is thought to be responsible for the observed strong increase in ice particle number concentration in mixed-phase clouds. In this study, we focus on the rime splintering also known as the Hallett–Mossop (HM) process, which still lacks physical and quantitative understanding. We report on an experimental study of rime splintering conducted in a newly developed setup under conditions representing convective mixed-phase clouds in the temperature range of −4 to −10 °C. The riming process was observed with high-speed video microscopy and infrared thermography, while potential secondary ice (SI) particles in the super-micron size range were detected by a custom-built ice counter. Contrary to earlier HM experiments, where up to several hundreds of SI particles per milligram of rime were found at −5 °C, we found no evidence of productive SIP, which fundamentally questions the importance of rime splintering. Further, we could exclude two potential mechanisms suggested to be the explanation for rime splintering: the freezing of droplets upon glancing contact with the rimer and the fragmentation of spherically freezing droplets on the rimer surface. The break-off of sublimating fragile rime spires was observed to produce very few SI particles, which is insufficient to explain the large numbers of ice particles reported in earlier studies. In the transition regime between wet and dry growth, in analogy to phenomena of the deformation of drizzle droplets upon freezing, we also observed the formation of spikes on the rimer surface, which might be a source of SIP.

Visualization and Analysis of Vocal Fold Dynamics in Various Voice Disorders

Objectives/HypothesisThis study aims to compare the glottal dynamics of vocal fold leukoplakia, laryngitis, and papilloma using various visualization techniques, including phonovibrograms (PVG) and glottovibrograms (GVG). It hypothesizes that these techniques can provide understanding of the vibratory dynamics of these voice disorders, which can aid in their objective diagnosis and deriving visual features for computer-assisted classifications. Study DesignThis work employs a comparative analyses of vocal fold disorders using visualization techniques. The study examines phonovibrograms (PVG), derivative of PVG (PVG-1), digital kymograms (DKG) and glottovibrograms (GVG) to analyze the glottal dynamics of vocal fold leukoplakia, laryngitis, and papilloma. MethodsThe study utilizes high-speed video (HSV) endoscopy to capture vocal fold behavior in different pathological conditions. PVG, GVG and DKG techniques are applied to visualize and analyze the vibratory patterns of the vocal folds. PVG offers a comprehensive portrayal of vocal fold motion, while GVG presents the distance between vocal fold contours. The study also examines PVG-1 as a derivative of PVG. ResultsDistinct modifications in vocal fold vibrations across various stages (open, closed, closing, and opening) are documented using PVG, PVG-1, GVG, DKG, and PVG trajectory. Healthy vocal folds exhibit consistent periodic patterns, while disorders like leukoplakia, laryngitis, and papilloma manifest unique features due to structural and functional variations. The methods employed identify both structural irregularities and functional deviations in vocal fold vibrations. ConclusionsComparative analyses using PVG and other visualization techniques aids in understanding the glottal dynamics of voice disorders. While laryngoscopy and stroboscopy are valuable for real-time assessment, offline analysis techniques like PVG and GVG are useful for tracking glottal dynamics during phonation and assessing treatment effectiveness over time. Studies like this will contribute to standardizing the PVG based diagnostic criteria for its clinical utility, and development of classification tools for improved diagnosis and management of vocal fold pathologies.

Time-resolved observation of 150 kHz high-power pulse burst high-frequency discharge using a high-speed video camera and an intensified charge coupled device camera

The discharge phase and time evolution of a 150 kHz high-power pulse burst discharge were observed. A vacuum chamber was constructed by connecting glass tubes on which a solenoid coil was wound. Burst pulses with a width of 1000 μs and a repetition rate of 10 Hz were applied to the solenoid coil. A high-speed video camera and an intensified CCD camera were used to record photographs of the discharges. Observation of the discharge phase using a high-speed camera showed that the discharge occurs at the time of 40 μs and propagates from the wall of the cylindrical reactor. Over time, the discharge pattern evolves, and a branched pattern appears. The number of the branches changes with time. The discharge blinks synchronize with the instantaneous power, which suggests that the discharge is generated and maintained by the electrostatic field generated by the sides of the coil. The propagation velocity calculated from downstream decreases with increasing pressure and increases with increasing power.

Deep Learning-Based Detection of Glottis Segmentation Failures

Medical image segmentation is crucial for clinical applications, but challenges persist due to noise and variability. In particular, accurate glottis segmentation from high-speed videos is vital for voice research and diagnostics. Manual searching for failed segmentations is labor-intensive, prompting interest in automated methods. This paper proposes the first deep learning approach for detecting faulty glottis segmentations. For this purpose, faulty segmentations are generated by applying both a poorly performing neural network and perturbation procedures to three public datasets. Heavy data augmentations are added to the input until the neural network’s performance decreases to the desired mean intersection over union (IoU). Likewise, the perturbation procedure involves a series of image transformations to the original ground truth segmentations in a randomized manner. These data are then used to train a ResNet18 neural network with custom loss functions to predict the IoU scores of faulty segmentations. This value is then thresholded with a fixed IoU of 0.6 for classification, thereby achieving 88.27% classification accuracy with 91.54% specificity. Experimental results demonstrate the effectiveness of the presented approach. Contributions include: (i) a knowledge-driven perturbation procedure, (ii) a deep learning framework for scoring and detecting faulty glottis segmentations, and (iii) an evaluation of custom loss functions.

Characterizing rheological behavior and fluidization of highly refined furnishes for process optimization

In this work, highly refined softwood bleached kraft pulp (SWBKP) furnishes, referred to here as XFC, were studied from the perspective of fiber suspension handling in processing. The rheology of the furnishes was studied with a rotational rheometer using a non-standard flow geometry to understand the viscosity development at different consistencies and the impact of temperature. For fluidization analysis during pipe flow, two optical methods were implemented; namely, optical coherence tomography (OCT) and high-speed video (HSV) imaging. The OCT was used to determine the small-scale floc structures near the pipe wall where the shear stress is highest, and the HSV imaging was applied for observing flow instabilities and XFC suspension uniformity at the pipe scale. All these issues can be significant in deciding the minimum flow rate required for a process pipe to get sufficient fluidization of XFC suspensions.

Application of High-Speed Video Recording in Solving Scientific and Practical Problems of Forensic Ballistics

Application of High-Speed Video Recording in Solving Scientific and Practical Problems of Forensic Ballistics

Features of ignition and combustion of low-grade coal mixed with pyrolysis liquid

THE RELEVANCE of the study lies in the need to use pyrolysis liquid from wood processing for combustion in boilers of medium and low power as part of mixtures with coal. The unpredictability of the ignition and combustion properties of such mixtures, as well as the lack of calculation methods, predetermined a predominantly experimental approach to the study of these processes. At the same time, for the widespread implementation of such technological solutions in practice, it is necessary to have relatively simple methods for assessing the ignition and combustion characteristics of these components. THE PURPOSE. Synthesize samples of pyrolysis liquid from two different sorts of wood and perform their characterization. Develop an experimental method for studying ignition and combustion characteristics of pyrolysis liquid mixed with low-reactivity coal. Perform research on ignition delay times and the composition of released gas-phase products. Determine the main mechanisms of action of the components in the mixture of low-grade coal with pyrolysis liquid they’re during ignition and combustion. METHODS. The study was carried out using an experimental technique based on a high-temperature muffle furnace equipped with a high-speed video camera and a once-through gas analyzer. RESULTS. The article presents the dependences of the ignition delay times and the concentration curves of gas-phase products released during combustion of mixtures of low-grade coal and two types of pyrolysis liquid in the temperature range of the heating medium 600-800 °C and additive concentrations from 0 to 20 wt.%. Linear approximation dependences of ignition delay times on additive concentrations were obtained, and the mechanism of action of the additive during combustion was formulated. CONCLUSION. It was found that an increase in the concentration of the additive in the mixture leads to a stable decrease in the ignition delay times, while the amount of gas-phase products formed varied additively with respect to the composition of the mixture. The shape of the concentration curves for the release of CO and NOx indicates the independent action of the components of the mixture. The mechanism of action of additives was proposed. It was based on significant contribution of their evaporation process followed by combustion in the gas phase, which, in turn, initiats the ignition of coal.

Influence of collision conditions between aerosol flows of liquid droplets and solid particles typical for wet vortex dust collectors

Various industrial devices and systems make use of collisions of droplets with solid particles in aerosol flows. The characteristics of these collisions are usually predicted adopting the same approaches as for binary collisions of a liquid droplet with a solid particle. However, the conditions of such binary collisions are different from those in the spray composition. There are very few experimental findings for sprays. The purpose of this research was to experimentally determine the characteristics of interaction of droplets with particles of slurry fuel components in sprays. High-speed three-dimensional video recording made it possible to identify conditions when liquid droplets break up, and droplets and particles agglomerate to form slurry droplets. Droplet-particle interaction regimes were identified. Collective effects in a cascade of droplet-particle interactions were recognized. The frequency of collision regime occurrence was determined, considering the recorded collective effects in sprays. The characteristics of droplet-particle collisions in sprays were compared with those of binary interactions. Conditions were determined when the findings on binary collisions can be adapted to different systems with multi-phase sprays. The findings obtained promote research and development in the field of secondary atomization of composite fuel droplets.

Nonlinear response to contact impact on the surface of an aluminum alloy AlMg6 exhibiting the Portevin-Le Chatelier effect

Intermittent plastic flow known as the Portevin-Le Chatelier effect is a pronounced nonlinear phenomenon in a material science. One of the traditional approaches to the study of nonlinear system is to identify and analyze its responses to an external impulsive action. In the present work, the influence of impact indentation on the evolution of the spatio-temporal patterns of localized strain in an AlMg alloy deformed under the Portevin-Le Chatelier effect is studied with using an acoustic emission technique and high-speed video recording of propagating deformation bands. Dynamic and nonlinear responses to impact indentation of the surface of an alloy deformed by uniaxial tension above the conditional yield strength are revealed; the first include high values of dynamic hardness and local strain and loading rates, while the second involve the threshold and multiple nature of the force and acoustic responses. It has been established that there is a threshold impact energy of the indenter at which an induced strain jump of minimum amplitude occurs, accompanied by the formation of bands of macrolocalized plastic deformation. The conditions are established under which the work of plastic deformation during the development of the induced strain jump significantly, by more than two orders of magnitude, exceeds the energy of the initiating impact, which acts only as a trigger for the “premature” release of the elastic energy accumulated in the material before the moment of impact. It is shown that the impact-induced bands of macrolocalized deformation represent a hidden three-dimensional type of erosion damage that reduces the mechanical stability and durability of the alloy. A phenomenological model is proposed for the formation of bands, strain jumps, and bursts of acoustic emission induced by an indenter impact, which qualitatively explains the experimental results obtained in the work.

Biomechanics of biting in loggerhead shrikes: jaw-closing force, velocity and an argument for power.

Differences in the physical and behavioral attributes of prey are likely to impose disparate demands of force and speed on the jaws of a predator. Because of biomechanical trade-offs between force and speed, this presents an interesting conundrum for predators of diverse prey types. Loggerhead shrikes (Lanius ludovicianus) are medium-sized (∼50 g) passeriform birds that dispatch and feed on a variety of arthropod and vertebrate prey, primarily using their beaks. We used high-speed video of shrikes biting a force transducer in lateral view to obtain corresponding measurements of bite force, upper and lower bill linear and angular displacements, and velocities. Our results show that upper bill depression (about the craniofacial hinge) is more highly correlated with bite force, whereas lower bill elevation is more highly correlated with jaw-closing velocity. These results suggest that the upper and lower jaws might play different roles for generating force and speed (respectively) in these and perhaps other birds as well. We hypothesize that a division of labor between the jaws may allow shrikes to capitalize on elements of force and speed without compromising performance. As expected on theoretical grounds, bite force trades-off against jaw-closing velocity during the act of biting, although peak bite force and jaw-closing velocity across individual shrikes show no clear signs of a force-velocity trade-off. As a result, shrikes appear to bite with jaw-closing velocities and forces that maximize biting power, which may be selectively advantageous for predators of diverse prey that require both jaw-closing force and speed.

Behavior and morphology combine to influence energy dissipation in mantis shrimp (Stomatopoda)

ABSTRACT Animals deliver and withstand physical impacts in diverse behavioral contexts, from competing rams clashing their antlers together to archerfish impacting prey with jets of water. Though the ability of animals to withstand impact has generally been studied by focusing on morphology, behaviors may also influence impact resistance. Mantis shrimp exchange high-force strikes on each other's coiled, armored telsons (tailplates) during contests over territory. Prior work has shown that telson morphology has high impact resistance. I hypothesized that the behavior of coiling the telson also contributes to impact energy dissipation. By measuring impact dynamics from high-speed videos of strikes exchanged during contests between freely moving animals, I found that approximately 20% more impact energy was dissipated by the telson as compared with findings from a prior study that focused solely on morphology. This increase is likely due to behavior: because the telson is lifted off the substrate, the entire body flexes after contact, dissipating more energy than exoskeletal morphology does on its own. While variation in the degree of telson coil did not affect energy dissipation, proportionally more energy was dissipated from higher velocity strikes and from strikes from more massive appendages. Overall, these findings show that analysis of both behavior and morphology is crucial to understanding impact resistance, and suggest future research on the evolution of structure and function under the selective pressure of biological impacts.

Postural Change of the Annual Cicada (Tibicen linnei) Helps Facilitate Backward Flight.

Cicadas are heavy fliers well known for their life cycles and sound production; however, their flight capabilities have not been extensively investigated. Here, we show for the first time that cicadas appropriate backward flight for additional maneuverability. We studied this flight mode using computational fluid dynamics (CFD) simulations based on three-dimensional reconstructions of high-speed videos captured in a laboratory. Backward flight was characterized by steep body angles, high angles of attack, and high wing upstroke velocities. Wing motion occurred in an inclined stroke plane that was fixed relative to the body. Likewise, the directions of the half-stroke-averaged aerodynamic forces relative to the body (local frame) were constrained in a narrow range (<20°). Despite the drastic difference of approximately 90° in body posture between backward and forward flight in the global frame, the aerodynamic forces in both flight scenarios were maintained in a similar direction relative to the body. The forces relative to the body were also oriented in a similar direction when observed during climbs and turns, although the body orientation and motions were different. Hence, the steep posture appropriated during backward flight was primarily utilized for reorienting both the stroke plane and aerodynamic force in the global frame. A consequence of this reorientation was the reversal of aerodynamic functions of the half strokes in backward flight when compared to forward flight. The downstroke generated propulsive forces, while the upstroke generated vertical forces. For weight support, the upstroke, which typically generates lesser forces in forward flight, is aerodynamically active in backward flight. A leading-edge vortex (LEV) was observed on the forewings during both half strokes. The LEV's effect, together with the high upstroke velocity, increased the upstroke's force contribution from 10% of the net forces in forward flight to 50% in backward flight. The findings presented in this study have relevance to the design of micro-aerial vehicles (MAVs), as backward flight is an important characteristic for MAV maneuverability or for taking off from vertical surfaces.

Convolutional neural networks for image analysis of high-speed videos from two slab burners

High-speed video recordings of slab burner experiments were analyzed using a machine learning approach with convolutional neural networks in order to compute the regression rate of hybrid rocket fuels over time. Combustion tests of paraffin-based fuel grains performed in two different hybrid rocket slab burners were recorded with high-speed video cameras and the resulting image data are analyzed in order to determine the height of the fuel in each frame. To this end, a deep neural network with U-net architecture is trained in a supervised fashion to segment the shape of the fuel slab. It is demonstrated that this approach is more capable to segment combustion images in unsteady flow conditions than classical computer vision methods based on thresholding or edge detection. Furthermore, methods in the area of uncertainty quantification of neural networks are applied to estimate the errors in the neural network prediction to new previously unseen data. Finally, the regression rate of the fuel is computed as the rate of change of this height. This method enables automatic analysis of a large amount of video data, taking full advantage of the optical access capabilities of slab burners. Additionally, the method delivers not only the time and space average values of the fuel regression rate, but also quantifies its variation over time and over the length of the slab, providing deeper insights into the combustion mechanics of hybrid rockets.

Using Pose Estimation and 3D Rendered Models to Study Leg-Mediated Self-righting by Lanternflies.

The ability to upright quickly and efficiently when overturned on the ground (terrestrial self-righting) is crucial for living organisms and robots. Previous studies have mapped the diverse behaviors used by various animals to self-right on different substrates, and proposed physical models to explain how body morphology can favor specific self-righting methods. However, to our knowledge, no studies have quantified and modeled all of an animal's limb motions during these complicated behaviors. Here, we studied terrestrial self-righting by immature invasive spotted lanternflies (Lycorma delicatula), an insect species that must frequently recover from being overturned after jumping and falling in its native habitat. These nymphs self-righted successfully in 92-100% of trials on three substrates with different friction and roughness, with no significant difference in the time or number of attempts required. They accomplished this using three stereotypic sequences of movements. To understand these motions, we combined 3D poses tracked on multi-view high-speed video with articulated 3D models created using photogrammetry and Blender rendering software. The results were used to calculate the mechanical properties (e.g., potential and kinetic energy, angular speed, stability margin, torque, force, etc.) of these insects during righting trials. We used an inverted physical pendulum model (a "template") to estimate the kinetic energy available in comparison to the increase in potential energy required to flip over. While these insects began righting using primarily quasistatic motions, they also used dynamic leg motions to achieve final tip-over. However, this template did not describe important features of the insect's center of mass trajectory and rotational dynamics, necessitating the use of an "anchor" model comprising the 3D rendered body model and six articulated two-segment legs to model the body's internal degrees of freedom and capture the role of the legs' contribution to inertial reorientation. This anchor elucidated the sequence of highly coordinated leg movements these insects used for propulsion, adhesion, and inertial reorientation during righting, and how they frequently pivot about a body contact point on the ground to flip upright. In the most frequently used method, diagonal rotation, these motions allowed nymphs to spin their bodies to upright with lower force with a greater stability margin compared to the other less frequently used methods. We provide a concise overview of necessary background on 3D orientation and rotational dynamics, and the resources required to apply these low-cost modeling methods to other problems in biomechanics.

Cavitation and jetting from shock wave refocusing near convex liquid surfaces

We study the physical mechanisms behind the ejection of a liquid jet from a curved free surface, specifically a free-falling water drop. The jet is produced after a spherical shock wave emitted from a micro-explosion created by a focused laser pulse is refocused on the opposite side of its source. The analysis of high-speed videos of the liquid jet formation revealed that it originates from a larger, prolate cavitation bubble created by the strong tension produced after the reflection of the original wave on the air–liquid interface. The shock wave propagation and jet formation are modeled separately with finite volume simulations in OpenFOAM. Initially we study the pressure evolution inside the drop by comparing the numerical simulations with the distribution of bubbles nucleated after the passage of the negative pressure wave. The jet formation dynamics is explained by comparing the experiments with numerical results. The jet velocity is higher if the laser focus is closer to the drop surface.

Modular multi-channel high voltage arbitrary waveform generator and imaging setup for dielectric elastomer actuator characterisation

Various applications require multi-channel high-voltage sources for their control, e.g. electrostatic adhesion, electrophoresis and artificial muscles such as piezoelectric, hydraulically amplified self-healing electrostatic(HASEL) and dielectric elastomer actuators(DEAs). Further, the ability to simultaneously monitor the state of the actuators either with images, or voltage and current sensing is crucial to characterise their behaviour. In this work, we present the design of a versatile characterisation setup, capable of generating eight HV (15 kV) arbitrary waveforms(rise time of 8 ms and fall time of 80 ms for 60 MΩ load), while synchronously monitoring voltage and current, and record high-speed (120 fps) video. The setup ensures modularity and customisability by consisting of three independent modules: (1) The imaging module includes a Raspberry Pi and a Pi Camera; (2) A 3.3 V analogue interface 16-bit resolution data acquisition module on a PCB that accommodates a microcontroller board, two 8-channel analogue-to-digital converters, and an 8-channel digital-to-analogue converter; (3) Up to 8 DC-to-HVDC converter boards powered by 12 V DC, with 3.3 V analogue interface.

Neuroethology: Decoding the waggle dance

A new study combining high-speed video recordings and computational modeling has revealed an overlooked feature of the famous honeybee waggle dance, yielding the first biologically plausible neural circuit model of how the information transmitted via the waggle dance could be assimilated by the follower bees.

Condensation shock topologies in carbon dioxide and a non-condensable gas mixture in supersonic nozzles

Condensation shock waves may occur in many flow expansion devices such as turbomachinery, gas ejectors, micro thrust-nozzles, and supersonic gas flow separators. However, their experimental analysis has been barely addressed as condensation shocks comprise complex phenomena such as compressible flow behavior, a shock-like phase transition, and a two-phase flow expansion. This work characterizes experimentally some condensation shock topologies of a mixture of carbon dioxide and dry air at several compositions in a Laval nozzle. Experiments were carried out in a test-rig instrumented with high-response pressure transducers installed along the Laval nozzle wall along with a Schlieren setup equipped with a high-speed video camera imaging the flow behavior within the nozzle. The nozzle wall profile was built by using the method of characteristics developed from a real equation-of-state suited for the testing mixture. Results revealed the influence of the nozzle wall profile on the condensation shock location and topology. Moreover, there types of flow behavior were captured and named as conventional, transition, and Mach wave condensation shocks. The transition from one topology to another occurred due to the interaction between cancelation waves originated from the nozzle wall and the phase-change phenomenon, giving rise to two distinct regions characterized by certain observable droplet population density. The current investigation presents an in-depth phenomenological discussion of the three types of condensation shock topologies as such assessment has not been previously developed.

The impact of changing drum rotation direction on fabric motion and drying performance in clothes dryers

Fabric motion in tumble dryers, particularly the motion observed from the cross-section of the rotating drum, contributes significantly to the heat and mass transfer between textiles and the surrounding hot airflow. However, the wider picture for this process is not yet clear and requires further study. In this article, fabric motion with different drum rotation direction settings was analyzed experimentally to determine the effect of drum rotation direction on drying performance. A high-speed video camera was used to record the fabric motion during the entire drying process. The recorded movies were then processed, and the velocity and occupancy distributions of the tracer fabric and several motion indexes were analyzed by using OpenCV and Matlab. The results indicated that changes in the drum rotation mode cause significant variations in the dynamics of fabric motion in domestic tumble dryers across different drying conditions with variations in fabric size, drum rotation speed and load size. Constantly changing drum rotation direction plays an important role in enlarging the motion area and reducing the passive motion area, lifting the textiles up to a higher place and agitating the mixture inside the rotating drum. This means that the fabrics can be effectively scattered instead of tangling together, and because this drying condition provides more opportunities for them to be exposed to the surrounding hot airflow, it enhances convective heat and mass transfer within the drying chamber and reduces the formation of wrinkles on fabrics. This study could lead to new guidance for obtaining effective fabric motion patterns that lead to an optimal drying performance.