High-sensitivity Nuclear Magnetic Resonance Research Articles

Custom GC×GC configuration for the selective isolation or removal of compounds from complex samples

We developed a novel approach to selectively isolate or remove nearly any compound from complex mixtures of volatile organic compounds. This was achieved by customizing a GC×GC system with a Deans switch, a passive splitter, and a custom-made adapter for sample recollection. The new setup was evaluated with 106 standard chemicals covering a wide range of volatility (boiling points: 56 – 343 ⁰C) and polarity (log P: 0.2 – 9.4). The method was used to remove two notorious malodorous compounds from spoiled wine samples. We found that the recovery can be maximized if a custom-made adapter is attached directly on the flame ionization detector port (average recovery rate of 76 ± 7 % for the standards). Eventually, we could selectively isolate or remove chemicals with peaks separated by a minimum distance of 50 ms for the second column throughout the whole chromatographic run. The developed system is expected to mainly be used in the field of flavor and fragrance analysis (i.e., selection of flavors and odorants of interest or removal of off-flavor or malodorous compounds). At present, we can reasonably collect about 100 ng of each single compound and are currently working on sample enrichment to improve our method to isolate sufficient amounts for further chemical analysis (e.g. high sensitivity nuclear magnetic resonance or chemical ionization tandem mass spectrometry).

Application of 2D-NMR with room temperature NMR probes for the assessment of the higher order structure of filgrastim

The higher order structure (HOS) of biotherapeutics is a critical quality attribute that can be evaluated by nuclear magnetic resonance (NMR) spectroscopy at atomic resolution. NMR spectral mapping of HOS can be used to establish HOS consistency of a biologic across manufacturing changes or to compare a biosimilar to an innovator reference product. A previous inter-laboratory study performed using filgrastim drug products demonstrated that two-dimensional (2D)-NMR 1HN-15NH heteronuclear correlation spectroscopy is a highly robust and precise method for mapping the HOS of biologic drugs at natural abundance using high sensitivity NMR ‘cold probes.’ Here, the applicability of the 2D-NMR method to fingerprint the HOS of filgrastim products is demonstrated using lower sensitivity, room temperature NMR probes. Combined chemical shift deviation and principal component analysis are used to illustrate the performance and inter-laboratory precision of the 2D-NMR method when implemented on room temperature probes.

Chemisorption of Water on the Surface of Silicon Microparticles Measured by Dynamic Nuclear Polarization Enhanced NMR

We use dynamic nuclear polarization (DNP) enhanced nuclear magnetic resonance (NMR) at liquid helium temperatures to directly detect hydrogen attached to the surface of silicon microparticles. The proton NMR spectrum from a dry sample of polycrystalline silicon powder (1-5 $\mu$m) shows a distinctively narrow Lorentzian-shaped resonance with a width of 6.2 kHz, indicative of a very sparse distribution of protons attached to the silicon surface. These protons are within a few atomic monolayers of the silicon surface. The high sensitivity NMR detection of surface protons from low surface area ($0.26 - 1.3 \: m^2/g$) particles is enabled by an overall signal enhancement of 4150 over the room temperature NMR signal at the same field. When the particles were suspended in a solvent with 80% H2O and 20% D2O, the narrow peak was observed to grow in intensity over time, indicating growth of the sparse surface proton layer. However, when the particles were suspended in a solvent with 20% H2O and 80% D2O, the narrow bound-proton peak was observed to shrink due to exchange between the surface protons and the deuterium in solution. This decrease was accompanied by a concomitant growth in the intensity of the frozen solvent peak, as the relative proton concentration of the solvent increased. When the particles were suspended in the organic solvent hexane, the proton NMR spectra remained unchanged over time. These results are consistent with the known chemisorption of water on the silicon surface resulting in the formation of hydride and hydroxyl species. Low-temperature DNP NMR can thus be used as a non-destructive probe of surface corrosion for silicon in aqueous environments. This is important in the context of using silicon MEMS and bioMEMS devices in such environments, for silicon micro- and nano-particle MRI imaging agents, and the use of nanosilicon for splitting water in fuel cells.

NMR study of nematic spin fluctuations in a detwinned single crystal of underdopedBa(Fe1−xCox)2As2

We report the experimental details of how mechanical detwinning can be implemented in tandem with high sensitivity nuclear magnetic resonance measurements and use this setup to measure the in-plane anisotropy of the spin-lattice relaxation rate in underdoped Ba(Fe$_{1-x}$Co$_{x}$)$_{2}$As$_{2}$ with $x=0.048$. The anisotropy reaches a maximum of 30\% at $T_{N}$, and the recovery data reveal that the glassy behavior of the spin fluctuations present in the twinned state persist in the fully detwinned crystal. A theoretical model is presented to describe the spin-lattice relaxation rate in terms of anisotropic nematic spin fluctuations.

High-sensitivity nuclear magnetic resonance at Giga-Pascal pressures: a new tool for probing electronic and chemical properties of condensed matter under extreme conditions.

Nuclear Magnetic Resonance (NMR) is one of the most important techniques for the study of condensed matter systems, their chemical structure, and their electronic properties. The application of high pressure enables one to synthesize new materials, but the response of known materials to high pressure is a very useful tool for studying their electronic structure and developing theories. For example, high-pressure synthesis might be at the origin of life; and understanding the behavior of small molecules under extreme pressure will tell us more about fundamental processes in our universe. It is no wonder that there has always been great interest in having NMR available at high pressures. Unfortunately, the desired pressures are often well into the Giga-Pascal (GPa) range and require special anvil cell devices where only very small, secluded volumes are available. This has restricted the use of NMR almost entirely in the past, and only recently, a new approach to high-sensitivity GPa NMR, which has a resonating micro-coil inside the sample chamber, was put forward. This approach enables us to achieve high sensitivity with experiments that bring the power of NMR to Giga-Pascal pressure condensed matter research. First applications, the detection of a topological electronic transition in ordinary aluminum metal and the closing of the pseudo-gap in high-temperature superconductivity, show the power of such an approach. Meanwhile, the range of achievable pressures was increased tremendously with a new generation of anvil cells (up to 10.1 GPa), that fit standard-bore NMR magnets. This approach might become a new, important tool for the investigation of many condensed matter systems, in chemistry, geochemistry, and in physics, since we can now watch structural changes with the eyes of a very versatile probe.

High-Sensitivity Nuclear Magnetic Resonance at Giga-Pascal Pressures: A New Tool for Probing Electronic and Chemical Properties of Condensed Matter under Extreme Conditions

High-Sensitivity Nuclear Magnetic Resonance at Giga-Pascal Pressures: A New Tool for Probing Electronic and Chemical Properties of Condensed Matter under Extreme Conditions

Moissanite anvil cell design for Giga-Pascal nuclear magnetic resonance.

A new design of a non-magnetic high-pressure anvil cell for nuclear magnetic resonance (NMR) experiments at Giga-Pascal pressures is presented, which uses a micro-coil inside the pressurized region for high-sensitivity NMR. The comparably small cell has a length of 22 mm and a diameter of 18 mm, so it can be used with most NMR magnets. The performance of the cell is demonstrated with external-force vs. internal-pressure experiments, and the cell is shown to perform well at pressures up to 23.5 GPa using 800 μm 6H-SiC large cone Boehler-type anvils. (1)H, (23)Na, (27)Al, (69)Ga, and (71)Ga NMR test measurements are presented, which show a resolution of better than 4.5 ppm, and an almost maximum possible signal-to-noise ratio.

Small Animal Imaging with Hyperpolarized 129Xe Magnetic Resonance

High-sensitivity nuclear magnetic resonance (NMR) of gaseous atoms realized by using a hyperpolarization technique is an attractive research tool used in a wide range of areas, such as physics, chemistry, material science and biomedical imaging. One of the most promising applications of this technology is the use as a noninvasive diagnostic tool for pulmonary diseases, where hyperpolarized (HP) noble gases, (3)He and (129)Xe, play a role as gaseous (i.e. inhalable) contrast agents of magnetic resonance imaging (MRI). During the last two decades, lung MRI with HP gases has become widely applicable from mouse to human. In this review we present a brief overview of recent progress made by our group in the development of HP (129)Xe MR measurements, while focusing on the methodology for probing pulmonary dysfunctions in mice.

High sensitivity nuclear magnetic resonance probe for anvil cell pressure experiments

While the highest pressures can be achieved with diamond anvil cells, limited sample size and anvil geometry have hampered their application in nuclear magnetic resonance (NMR) experiments due to weak signal-to-noise. Here we report a new probe design that is based on having the resonant radio frequency coil that encloses the sample within the anvil cell inside the gasket hole. This increases the filling factor tremendously and results in greatly enhanced NMR sensitivity. The setup is described together with room temperature Na and Al NMR experiments.

Electronic characterization of lithographically patterned microcoils for high sensitivity NMR detection

Nuclear magnetic resonance (NMR) offers a non-destructive, powerful, structure-specific analytical method for the identification of chemical and biological systems. The use of radio frequency (RF) microcoils has been shown to increase the sensitivity in mass-limited samples. Recent advances in micro-receiver technology have further demonstrated a substantial increase in mass sensitivity [D.L. Olson, T.L. Peck, A.G. Webb, R.L. Magin, J.V. Sweedler, High-resolution microcoil H-1-NMR for mass-limited, nanoliter-volume samples, Science 270 (5244) (1995) 1967–1970]. Lithographic methods for producing solenoid microcoils possess a level of flexibility and reproducibility that exceeds previous production methods, such as hand winding microcoils. This paper presents electrical characterizations of RF microcoils produced by a unique laser lithography system that can pattern three dimensional surfaces and compares calculated and experimental results to those for wire wound RF microcoils. We show that existing optimization conditions for RF coil design still hold true for RF microcoils produced by lithography. Current lithographic microcoils show somewhat inferior performance to wire wound RF microcoils due to limitations in the existing electroplating technique. In principle, however, when the pitch of the RF microcoil is less than 100μm lithographic coils should show comparable performance to wire wound coils. In the cases of larger pitch, wire cross sections can be significantly larger and resistances lower than microfabricated conductors.

Probing the molecular-level control of aluminosilicate dissolution: A sensitive solid-state NMR proxy for reactive surface area

For two suites of volcanic aluminosilicate glasses, the accessible and reactive sites for covalent attachment of the fluorine-containing (3,3,3-trifluoropropyl)dimethylchlorosilane (TFS) probe molecule were measured by quantitative 19F nuclear magnetic resonance (NMR) spectroscopy. The first set of samples consists of six rhyolitic and dacitic glasses originating from volcanic activity in Iceland and one rhyolitic glass from the Bishop Tuff, CA. Due to differences in the reactive species present on the surfaces of these glasses, variations in the rate of acid-mediated dissolution (pH 4) for samples in this suite cannot be explained by variations in geometric or BET-measured surface area. In contrast, the rates scale directly with the surface density of TFS-reactive sites as measured by solid-state NMR. These data are consistent with the inference that the TFS-reactive M-OH species on the glass surface, which are known to be non-hydrogen-bonded Q 3 groups, represent loci accessible to and affected by proton-mediated dissolution. The second suite of samples, originating from a chronosequence in Kozushima, Japan, is comprised of four rhyolites that have been weathered for 1.1, 1.8, 26, and 52 ka. The number of TFS-reactive sites per gram increases with duration of weathering in the laboratory for the “Icelandic” samples and with duration of field weathering for both “Icelandic” and Japanese samples. One hypothesis is consistent with these and published modeling, laboratory, and field observations: over short timescales, dissolution is controlled by fast-dissolving sites, but over long timescales, dissolution is controlled by slower-dissolving sites, the surface density of which is proportional to the number of TFS-reactive Q 3 sites. These latter sites are not part of a hydrogen-bonded network on the surface of the glasses, and measurement of their surface site density allows predictions of trends in reactive surface area. The TFS treatment method, which is easily monitored by quantitative 19F solid-state NMR, therefore provides a chemically specific and quantifiable proxy to understand the nature of how sites on dissolving silicates control dissolution. Furthermore, 27Al NMR techniques are shown here to be useful in identifying clays on the glass surfaces, and these methods are therefore effective for quantifying concentrations of weathering impurities. Our interpretations offer a testable hypothesis for the mechanism of proton-promoted dissolution for low-iron aluminosilicate minerals and glasses and suggest that future investigations of reactive surfaces with high-sensitivity NMR techniques are warranted.

Low Molecular Weight Heparins: Structural Differentiation by Bidimensional Nuclear Magnetic Resonance Spectroscopy

Individual low molecular weight heparins (LMWHs) exhibit distinct pharmacological and biochemical profiles because of manufacturing differences. Correlation of biological properties with particular structural motifs is a major challenge in the design of new LMWHs as well as in the development of generic versions of proprietary LMWHs. Two-dimensional nuclear magnetic resonance (NMR) spectroscopy permits identification and quantification of structural peculiarities of LMWH preparations. In this article, heteronuclear single quantum coherence spectroscopy, previously used to determine variously substituted monosaccharide components of heparan sulfate (HS) and HS-like glycosaminoglycan mimics, has been applied to the structural characterization of three commercially available LMWHs (enoxaparin, dalteparin, and tinzaparin). Relevant residues belonging to the parent heparin, as well as minor residues generated by each depolymerization procedure, have been characterized and quantified. The use of a high-sensitivity NMR spectrometer (600 MHz equipped with cryoprobe) allowed the accurate quantification of residues with sensitivity better than 1 to 2%.

High-resolution, high-sensitivity NMR of nanolitre anisotropic samples by coil spinning

Nuclear magnetic resonance (NMR) can probe the local structure and dynamic properties of liquids and solids, making it one of the most powerful and versatile analytical methods available today. However, its intrinsically low sensitivity precludes NMR analysis of very small samples-as frequently used when studying isotopically labelled biological molecules or advanced materials, or as preferred when conducting high-throughput screening of biological samples or 'lab-on-a-chip' studies. The sensitivity of NMR has been improved by using static micro-coils, alternative detection schemes and pre-polarization approaches. But these strategies cannot be easily used in NMR experiments involving the fast sample spinning essential for obtaining well-resolved spectra from non-liquid samples. Here we demonstrate that inductive coupling allows wireless transmission of radio-frequency pulses and the reception of NMR signals under fast spinning of both detector coil and sample. This enables NMR measurements characterized by an optimal filling factor, very high radio-frequency field amplitudes and enhanced sensitivity that increases with decreasing sample volume. Signals obtained for nanolitre-sized samples of organic powders and biological tissue increase by almost one order of magnitude (or, equivalently, are acquired two orders of magnitude faster), compared to standard NMR measurements. Our approach also offers optimal sensitivity when studying samples that need to be confined inside multiple safety barriers, such as radioactive materials. In principle, the co-rotation of a micrometre-sized detector coil with the sample and the use of inductive coupling (techniques that are at the heart of our method) should enable highly sensitive NMR measurements on any mass-limited sample that requires fast mechanical rotation to obtain well-resolved spectra. The method is easy to implement on a commercial NMR set-up and exhibits improved performance with miniaturization, and we accordingly expect that it will facilitate the development of novel solid-state NMR methodologies and find wide use in high-throughput chemical and biomedical analysis.

Controlled multiple quantum coherences of nuclear spins in a nanometre-scale device

The analytical technique of nuclear magnetic resonance (NMR) is based on coherent quantum mechanical superposition of nuclear spin states. Recently, NMR has received considerable renewed interest in the context of quantum computation and information processing, which require controlled coherent qubit operations. However, standard NMR is not suitable for the implementation of realistic scalable devices, which would require all-electrical control and the means to detect microscopic quantities of coherent nuclear spins. Here we present a self-contained NMR semiconductor device that can control nuclear spins in a nanometre-scale region. Our approach enables the direct detection of (otherwise invisible) multiple quantum coherences between levels separated by more than one quantum of spin angular momentum. This microscopic high sensitivity NMR technique is especially suitable for probing materials whose nuclei contain multiple spin levels, and may form the basis of a versatile multiple qubit device.

ALGORITHMIC COOLING OF SPINS: A PRACTICABLE METHOD FOR INCREASING POLARIZATION

An efficient technique to generate ensembles of spins that are highly polarized by external magnetic fields is the Holy Grail in Nuclear Magnetic Resonance (NMR) spectroscopy. Since spin-half nuclei have steady-state polarization biases that increase inversely with temperature, spins exhibiting high polarization biases are considered cool, even when their environment is warm. Existing spin-cooling techniques are highly limited in their efficiency and usefulness. Algorithmic cooling is a promising new spin-cooling approach that employs data compression methods in open systems. It reduces the entropy of spins on long molecules to a point far beyond Shannon's bound on reversible entropy manipulations, thus increasing their polarization. Here we present an efficient and experimentally feasible algorithmic cooling technique that cools spins to very low temperatures even on short molecules. This practicable algorithmic cooling could lead to breakthroughs in high-sensitivity NMR spectroscopy in the near future, and to the development of scalable NMR quantum computers in the far future. Moreover, while the cooling algorithm itself is classical, it uses quantum gates in its implementation, thus representing the first short-term application of quantum computing devices.

Low-conductivity buffers for high-sensitivity NMR measurements.

The sensitivity of nuclear magnetic resonance (NMR) probes, especially the recently introduced cryogenic probes, can be substantially reduced by the electrical noise generated by conductive samples. In particular, samples of biological macromolecules, which usually contain salts to keep the pH constant and to prevent aggregation, can experience a significant reduction in sensitivity. So far this dependence has forced researchers to minimize the salt concentrations in their samples. Here we demonstrate that the decisive factor is not the salt concentration itself but the conductivity which is a function of both the concentration and the mobility of the ions in solution. We show that by choosing buffers with low ionic mobility, the sample conductivity can be dramatically reduced and the sensitivity substantially enhanced compared to the same measurement with an equal concentration of a standard NMR buffer such as phosphate. We further show that the highest sensitivity gain of one buffer over another buffer is equal to the square root of the ratio of their ion mobilities and describe a simple method to evaluate the effect of a certain buffer on the sensitivity.

High-Sensitivity Multinuclear NMR Spectroscopy of a Smectite Clay and of Clay-Intercalated Polymer

The nuclear magnetic resonance (NMR) properties of a smectite clay low in paramagnetic ions, and NMR experiments to detect organic material near the silicate surfaces with high sensitivity, have been explored by 1H, 29Si, and 13C NMR. In oven-dried hectorite clay, 1H NMR reveals a sharp signal at 0.35 ppm that narrows significantly with spinning speed. It is assigned to the “inner” OH protons of the silicate layers. In fluorohectorite, where the OH groups are replaced by fluorines, no such 1H peak is observed. The assignment is further confirmed by the efficient cross-polarization observed in two-dimensional (2D) 1H– 29Si HETCOR spectra, and by 29Si-detected REDOR experiments with 1H-dephasing in the 29Si dipolar field, which yield a 1H– 29Si distance of 2.9±0.4 Å. In these 1H– 29Si experiments, the sensitivity of the 29Si signal is enhanced at least fivefold by refocusing the decay resulting from the inhomogeneous broadening of the single 29Si peak, stretching the 29Si signal out over 80 ms. The small 1H linewidth of this signal at spinning frequencies exceeding 4 kHz is attributed to the large proton–proton distances in the clay. The upfield isotropic chemical shift of the OH groups is explained by their inaccessibility to hydrogen-bonding partners, as a result of their location in hexagonal “cavities” of the clay structure. The well-resolved, easily selectable OH-proton signal and the high-sensitivity 29Si detection open excellent perspectives for NMR studies of composites of clays with organic molecules. Two-dimensional 1H– 29Si and 1H– 1H chemical-shift correlation experiments enable efficient detection of the 1H spectrum of organic segments near the clay surface. Combined with 1H spin diffusion, the organic segments at up to several nanometers from the clay surfaces can be probed. A 2D 1H– 13C correlation experiment yields the 13C spectrum of the organic species near the clay surfaces. A mobility gradient of intercalated poly(ethylene oxide), PEO, segments is proven in 1H– 29Si WISE experiments with spin diffusion.