High-resolution Microscopy Techniques Research Articles

Facile and innovation synthesis of Zn-Mn-Co-LDH/polypyrrole and its application in investigating ethanol oxidation in an alkaline medium

Overvoltage and low current are observed for ethanol electrooxidation on the surface of many unmodified electrodes. Therefore, it is desirable to use a suitable catalyst for ethanol electrooxidation to increase the current. This research introduces a new sensor to catalyze ethanol oxidation in an alkaline environment. This new Zn-Mn-Co LDH/PolyPyrrole/GCE nanocomposite sensor exhibits high catalytic activity for ethanol electrooxidation. It changes the oxidation potential of ethanol to a less positive potential. To identify this proposed sensor, X-ray diffraction (XRD), Brauner Emmett-Teller (BET), X-ray photoelectron spectroscopy (XPS), FT-IR spectroscopy, field emission scanning electron microscopy (FESEM), thermal analysis (TGA), high-resolution transmission electron microscopy (HR-TEM) and cyclic voltammetry techniques were used. Ethanol electrooxidation was investigated by cyclic voltammetry technique. The effects of scan rate and ethanol concentration on the ethanol oxidation peak have been investigated. The proposed sensor showed long-term stability. This prepared nanocomposite can be used as an anode catalyst for ethanol fuel cells.

Enhancement of photocatalytic activity by thermal annealing of Au, Ag, and Cu implanted TiN thin films

The paper presents an investigation on the optoelectronic and photocatalytic properties of titanium-nitride (TiN) thin films, modified through the introduction of metal ions (Au, Ag, and Cu) during implantation, followed by thermal annealing. Employing high-resolution microscopic and spectroscopic techniques, we examined the microstructural and compositional features of the films in detail. The films exhibited a crystalline structure with distinct columnar patterns, attributed to defect release and recovery during annealing. Furthermore, metal nanoparticles were detected in samples implanted with gold and silver ions, indicating coalescence processes, while no such particles were observed in the case of Cu ions. Post-implantation annealing also led to surface oxidation and the formation of anatase TiO2, with a coexistence of TiO2, TiN, metallic Au and Ag, and CuO phases in subsurface regions. Comparative optical measurements revealed significant changes in photoluminescence efficiency and photocatalytic response of modified TiN. All implanted samples showed reduced photoluminescence intensity compared to pristine titanium-nitride, with the Au-implanted film exhibiting the most significant decrease, due to the presence of surface Au nanoparticles, thus resulting in the slower electron-hole recombination rates and enhanced photocatalytic activity.

Biogenic synthesis of hollow carbon dots using cigarette ash for photocatalytic and sensing applications

In this research article, the synthesis of hollow carbon dots (HCDs) from cigarette ash (CA) as a precursor using simple pyrolysis method is presented. The unique hollow nature of synthesized HCDs was confirmed by high-resolution transmission electron microscopy and nitrogen physisorption techniques. HCDs, with a size of ∼ 9 nm, exhibit specific surface area of 12.1 m2/g and stimulated pore diameter of 2.1 nm. HCDs demonstrated remarkable degradation efficiency by eradicating 91 % of rose Bengal dye within 120 min under UV irradiation at pH = 5.00 and display selective and sensitive detection of Fe3+ with a detection limit of around 1.1 µM. Ecological effect of HCDs on sprouted seeds of chickpea (Cicer arietinum) and wheat (Triticum aestivum) revealed their capacity to positively influence multiple aspects of plant development. Introduction of HCDs into growth medium (water) appeared to stimulate shoot, root, and leaf growth, suggesting a potential role for HCDs in enhancing overall plant health and productivity. These findings enabled HCDs derived from CA as promising candidate for sensitive metal ions detection, environmental remediation, and plant growth enhancement. It is the first time to upcycle CA into distinctive HCDs, serving as a potent tool for detecting and breaking down environmental contaminants.

Electrochemical Conversion of CO2 to Fuels and Useful Chemicals over Metal Supported Solid Oxide Electrolyzers

Electrochemical conversion of CO2 and H2O to fuels and chemicals provides a promising approach to simultaneously mitigate greenhouse emission and store surplus energy, which reduces electricity network variation due to increased intermittent renewable energy (such as solar and wind) utilization. Metal supported solid oxide electrolyzers (MS-SOEs) developed at Lawrence Berkeley National Laboratory provide advantages of rapid start-up, mechanical ruggedness, redox tolerance, dynamic operation, and low-cost materials. A relatively high operating temperature range of 600 to 750°C promotes energy efficiency and allows utilization of thermal energy such as steam.In this work, efficient and stable catalysts developed at the University of South Carolina have been infiltrated in the symmetrical and porous MS-SOE architecture. The phase purity has been analyzed by X-day diffraction. The morphologies of these infiltrated and posttest catalysts have been examined by scanning electron microscopy. Optimization of cell structure, processing temperature, cell voltage, and catalyst infiltration cycles for better cell performance will be presented. The stability of MS-SOEs has been evaluated during continuous operation for >200 hours. The cell degradation mechanisms revealed by electrochemical impedance spectroscopy and high-resolution scanning electron microscopy techniques will be presented.In addition to pure CO2 electrochemical conversion, effects of additional water and hydrogen in CO2 feedstock will be analyzed. Faradic efficiency and chemical selectivity calculated from gas chromatograph and electrochemical analyses will be presented.

Computational Characterization of the On-Surface Synthesis of Low-Dimensional Nanostructures

On-surface chemistry represents a fast-growing field allowing to synthesize molecular structures not available by traditional wet chemistry. In this context, high-resolution scanning probe microscopy techniques are able to provide unprecedented spatial resolution, allowing to precisely identify individual products of the reactions. Nevertheless, a deep understanding of the reaction mechanism under the conditions imposed by the substrate remains unknown.Nowadays, various computational strategies are employed to characterize the optimal reaction pathways of the chemical processes that take place on the surfaces of solids. For example, one of the most popular approaches is the nudged elastic band (NEB) as well as different transition state theory methods beyond it. These approaches had demonstrated their capability to characterize the potential energy landscape of the reaction pathways [1-2]. Another approach that had attracted the interest of the on-surface synthesis community is the application of molecular dynamics (MD) methods, within the canonical ensemble, and based on the QM/MM (quantum mechanics/molecular mechanics) of the interatomic forces [3-4]. This approach, which combines Density functional theory (DFT) and empirical force fields to describe the interaction forces, allows to simulate very large systems, at a very low computational cost while still accounting for the crucial quantum mechanics interactions. Also, such temperature-dependent simulations include the effect of entropy, vibrations modes, concerted motion, etc.I will present the experimental and computational results of different projects in which we have made use of the aforementioned computational approaches to achieve a better understanding of the on-surface synthesis experiments performed by the group. For example, the rationalization of the selective cyclodehydrogenation of non-benzenoid nanographenes deposited on a Au(111) substrate by means of temperature-dependent MD calculations and the analysis of the obtained vibrational modes (See Figure 1a). The group had also studied the stepwise transformation of coronene-based organometallic networks into two-dimensional covalent patches through intermolecular homocoupling (See Figure 1b). We had as well investigated the transformation of indenyl precursors, through a triple C-H cleavage followed by a peripheral directed homocoupling, to form a polyacetylene backboned polymer that features a parity dependent and highly delocalized soliton in-gap state (See Figure 1c).

Covalent Organic Framework Membranes with Patterned High-Density Through-Pores for Ultrafast Molecular Sieving.

The creation of uniformly molecular-sized through-pores within polymeric membranes and the direct evidence of these pores are essential for fundamentally understanding the transport mechanism and improving separation efficiency. Herein, we report an electric-field-assisted interface synthesis approach to fabricating large-area covalent organic framework (COF) membranes that consist of preferentially oriented single-crystalline COF domains. These single-crystalline frameworks were translated into high-density, vertically aligned through-pores across the entire membrane, enabling the direct visualization of membrane pores with an ultrahigh resolution of 2 Å using the low-dose high-resolution transmission electron microscopy technique (HRTEM). The density of directly visualized through-pores was quantified to be 1.2 × 1017 m-2, approaching theoretical predictions. These COF membranes demonstrate ultrahigh solvent permeability, which is 10 times higher than that of state-of-the-art organic solvent nanofiltration membranes. When applied to high-value pharmaceutical separations, their COF membranes exhibit 2 orders of magnitude higher methanol permeance and 20-fold greater enrichment efficiency than their commercial counterparts.

Fresh sodium storage of FeCoNi alloys confined in biomass carbon revealed by operando magnetometry

Focusing on the commercialization of sodium ion batteries (SIBs), the biggest challenge is discovering proper anode materials with high availability and safety. Among various materials, alloying metal anodes can achieve high-capacity sodium storage. However, transition metals, such as Fe, Co, Ni, etc. are considered to be inactive alloying with Na. Herein, by introducing trimetallic FeCoNi alloy nanoparticles confined in waste wool-derived carbon based on a sulfhydryl domain-limiting strategy, we synthesize porous N, S co-doped biomass carbon-coated trimetallic FeCoNi alloy composites (FeCoNi@NSC). Surprisingly, the optimal FeCoNi@NSC anode displays superior reversible specific capacities of 439.4 mAh·g−1 at 0.1 A·g−1, and an excellent cycling life of up to1000 cycles at 4 A·g−1, which is similar to that of the current reported tin/antimony/germanium/bismuth-based anodes. Besides the capacity contribution of biomass carbon, the combination of in situ magnetometry, high-resolution transmission electron microscopy and electrochemical impedance characterization techniques reveal that the rising capacity originates from spin-polarized surface capacitance, extra capacity of transition metal oxides, and low-voltage capacity of solid electrolyte interphase, as quantificated by monitoring the variation in magnetism of surface capacitance. This work provides a breakthrough concept for novel anode materials of SIBs choices.

Identification of solid phase speciation of trace elements in dust dry deposition using focused ion beam and selected area electron diffraction

BackgroundFew studies have been conducted to identify solid phase speciation of trace elements within the interior of airborne particles, although the adverse effects of ambient particles are closely related to the speciation of toxic elements and therefore the identification of chemical binding sites and solid phase associations is essential for assessing the impacts of trace elements in ambient air on environmental quality and human health. ObjectiveA combined use of focused ion beam scanning electron microscopy (FIB-SEM) and selected area electron diffraction (SAED) patterns from transmission electron microscopy (TEM) was applied with an energy dispersive X-ray spectroscopy (EDS) to investigate the solid phase speciation of trace elements within the interior of dust dry deposition obtained from an urban area. ResultsThe study results using the high-resolution microscopic techniques for the characterization of nano- and micron-sized particles revealed lead chromate for Pb and Cr6+, barite for Ba, rutile for Ti, and calcite, gypsum, and quicklime for Ca within the carbon matrix, implying their traffic-related sources. Fe oxides were observed for Fe, Mn, Ni, and Cr3+, with cerianite and Fe-La alloys for rare earth elements (REEs). ConclusionsThree types of anthropogenic sources were inferred based on the morphology and texture of the solid phases, as well as their primary usage: traffic road marking paints for Pb, Cr6+, Ba, and Ti, cement materials for Ca, and industrial activities for Fe, Mn, Ni, Cr3+, and REEs. The presence of submicron-sized toxic metal-bearing particles in dust dry deposition indicated that the toxic metals (i.e., Pb, Cr6+) can penetrate into the respiratory system along with the nanoparticles. The study results demonstrate that the solid phase speciation of trace elements detected using FIB-SEM and TEM-SAED can be effectively utilized for the identification of sources and the assessment of chemical toxicity of atmospheric dust.

Ex ovo omnia-why don't we know more about egg quality via imaging?

Determining egg quality is the foremost challenge in assisted reproductive technology (ART). Although extensive advances have been made in multiple areas of ART over the last 40 years, oocyte quality assessment tools have not much evolved beyond standard morphological observation. The oocyte not only delivers half of the nuclear genetic material and all of the mitochondrial DNA to an embryo but also provides complete developmental support during embryonic growth. Oocyte mitochondrial numbers far exceed those of any somatic cell, yet little work has been done to evaluate the mitochondrial bioenergetics of an oocyte. Current standard oocyte assessment in in vitro fertilization (IVF) centers include the observation of oocytes and their surrounding cell complex (cumulus cells) via stereomicroscope or inverted microscope, which is largely primitive. Additional oocyte assessments include polar body grading and polarized light meiotic spindle imaging. However, the evidence regarding the aforementioned methods of oocyte quality assessment and IVF outcomes is contradictory and non-reproducible. High-resolution microscopy techniques have also been implemented in animal and human models with promising outcomes. The current era of oocyte imaging continues to evolve with discoveries in artificial intelligence models of oocyte morphology selection albeit at a slow rate. In this review, the past, current, and future oocyte imaging techniques will be examined with the goal of drawing attention to the gap which limits our ability to assess oocytes in real time. The implications of improved oocyte imaging techniques on patients undergoing IVF will be discussed as well as the need to develop point of care oocyte assessment testing in IVF labs.

Origins and Importance of Intragranular Cracking in Layered Lithium Transition Metal Oxide Cathodes.

Li-ion batteries have a pivotal role in the transition toward electric transportation. Ni-rich layered transition metal oxide (LTMO) cathode materials promise high specific capacity and lower cost but exhibit faster degradation compared with lower Ni alternatives. Here, we employ high-resolution electron microscopy and spectroscopy techniques to investigate the nanoscale origins and impact on performance of intragranular cracking (within primary crystals) in Ni-rich LTMOs. We find that intragranular cracking is widespread in charged specimens early in cycle life but uncommon in discharged samples even after cycling. The distribution of intragranular cracking is highly inhomogeneous. We conclude that intragranular cracking is caused by local stresses that can have several independent sources: neighboring particle anisotropic expansion/contraction, Li- and TM-inhomogeneities at the primary and secondary particle levels, and interfacing of electrochemically active and inactive phases. Our results suggest that intragranular cracks can manifest at different points of life of the cathode and can potentially lead to capacity fade and impedance rise of LTMO cathodes through plane gliding and particle detachment that lead to exposure of additional surfaces to the electrolyte and loss of electrical contact.

Field-induced magnetorheological study towards the active magneto-viscoelastic behavior of stable MnFe2O4 magnetic nanofluid

This work presents the fine-tuned synthesis of MnFe2O4 oleic acid-coated magnetic nanoparticles (MNPs) by the chemical co-precipitation method. The X-ray photoelectron spectroscopy (XPS) was utilized to investigate the elemental composition and oxidation state of oleic acid-coated MnFe2O4 MNPs. The Fourier transform infrared spectroscopy (FTIR) spectra were used to confirm the functional groups in the oleic acid-coated MnFe2O4 magnetic nanoparticles. The spherical shape of MnFe2O4 MNPs is confirmed by Field emission scanning electron microscopy (FESEM) and High-resolution transmission electron microscopy (HRTEM) techniques. Zeta potential (ζ) measurements were performed to confirm the stability of MnFe2O4 magnetic nanofluid (MNF). Magnetic measurements (M−vs−H) reveal the saturation magnetization, Ms = 20.3 emu/g and coercivity, HC = 30 Oe, confirming the single domain superparamagnetic nature at 300 K. Field-induced shear thinning behavior of the MnFe2O4 magnetic fluid is confirmed by a power law, η = c γn + n∞ and steady-state behavior measurements. Magneto viscous effect initially increased at a low shear rate of 20 s−1 and then decreased at a higher shear rate of 100 s−1, which confirms the stability of the MnFe2O4 magnetic fluid. Also, the highest deflection angle, θ = 243 m.rad of MnFe2O4 magnetic fluid was observed at a moderate shear rate 100 s−1 and a high magnetic field of 1.2 T, while the lowest value of deflection angle, θ = 65 m.rad was observed in the absence of magnetic field. In contrast, the storage modulus (G') is greater than the loss modulus (G''), in corroboration with the viscoelastic-to-viscous behavior of MnFe2O4 magnetic fluid.

Photocatalytic H2 generation and CO2 reduction by WB5-x cocatalyst of TiO2 catalyst

Catalytic reactions play an important role in modern industry as almost 90 % of the chemical industry is based on catalytic reactions. The development of new, more efficient catalysts will allow significant advances in chemical production, but still remains a rather challenging problem for materials scientists. Here, we have proposed and investigated a new composite photocatalyst based on WB5-x-WB2 and TiO2 for H2 evolution from aqueous ethanol solution and CO2 reduction under visible light irradiation (410 nm). New composite photocatalysts WB5-x-WB2/TiO2 were synthesized and characterized by X-ray diffraction, UV–vis spectroscopy, X-ray photoelectron spectroscopy, and high-resolution transmission electron microscopy. Photocatalytic measurements show that the maximum activity of the composite photocatalyst 4 and 23 times higher than the activity of unmodified TiO2 in CO2 reduction and H2 evolution, respectively. Density functional calculations of the proposed reaction are in agreement with the provided experiments confirming the higher efficiency of the modified catalyst compared to TiO2.

Decomposition and dewetting of super-saturated Cu-15 at. % Co solid solution film

Nano-structured copper thin films present numerous applications for miniaturization of electronic devices. Their long term stability is key for reliable functionality. This work explores the thermal stability and solid state dewetting of a Cu-Co solid solution thin film and compares it to pure Cu. As according to the phase diagram Co is practically immiscible in Cu at room temperature, a metastable solid solution of Cu-15 at. % Co was deposited as thin film on a sapphire wafer. The microstructural evolution of the Co super-saturated film at temperatures ranging from 673 to 1073 K was evaluated using X-ray diffraction and high resolution microscopy techniques such as scanning electron and transmission electron microscopy. Interestingly, there is a competition between grain growth and phase separation. Co precipitates at grain boundaries acting as pinning sites preventing rapid grain growth during heat treatment at intermediate annealing temperature. However, grain growth occurs very quickly at higher temperatures, once the elemental phases of Cu and Co are formed. The competition between grain growth and phase separation and their consequence for dewetting are discussed.

Direct observation of a crescent-shape chromosome in expanded Bacillus subtilis cells

Bacterial chromosomes are folded into tightly regulated three-dimensional structures to ensure proper transcription, replication, and segregation of the genetic information. Direct visualization of chromosomal shape within bacterial cells is hampered by cell-wall confinement and the optical diffraction limit. Here, we combine cell-shape manipulation strategies, high-resolution fluorescence microscopy techniques, and genetic engineering to visualize the shape of unconfined bacterial chromosome in real-time in live Bacillus subtilis cells that are expanded in volume. We show that the chromosomes predominantly exhibit crescent shapes with a non-uniform DNA density that is increased near the origin of replication (oriC). Additionally, we localized ParB and BsSMC proteins – the key drivers of chromosomal organization – along the contour of the crescent chromosome, showing the highest density near oriC. Opening of the BsSMC ring complex disrupted the crescent chromosome shape and instead yielded a torus shape. These findings help to understand the threedimensional organization of the chromosome and the main protein complexes that underlie its structure.

Oxygen Transport through Amorphous Cathode Coatings in Solid-State Batteries.

All solid-state batteries (SSBs) are considered the most promising path to enabling higher energy-density portable energy, while concurrently improving safety as compared to current liquid electrolyte solutions. However, the desire for high energy necessitates the choice of high-voltage cathodes, such as nickel-rich layered oxides, where degradation phenomena related to oxygen loss and structural densification at the cathode surface are known to significantly compromise the cycle and thermal stability. In this work, we show, for the first time, that even in an SSB, and when protected by an intact amorphous coating, the LiNi0.5Mn0.3Co0.2O2 (NMC532) surface transforms from a layered structure into a rocksalt-like structure after electrochemical cycling. The transformation of the surface structure of the Li3B11O18 (LBO)-coated NMC532 cathode in a thiophosphate-based solid-state cell is characterized by high-resolution complementary electron microscopy techniques and electron energy loss spectroscopy. Ab initio molecular dynamics corroborate facile transport of O2- in the LBO coating and in other typical coating materials. This work identifies that oxygen loss remains a formidable challenge and barrier to long-cycle life high-energy storage, even in SSBs with durable, amorphous cathode coatings, and directs attention to considering oxygen permeability as an important new design criteria for coating materials.

Transmembrane protein 97 is a potential synaptic amyloid beta receptor in human Alzheimer’s disease

Synapse loss correlates with cognitive decline in Alzheimer’s disease, and soluble oligomeric amyloid beta (Aβ) is implicated in synaptic dysfunction and loss. An important knowledge gap is the lack of understanding of how Aβ leads to synapse degeneration. In particular, there has been difficulty in determining whether there is a synaptic receptor that binds Aβ and mediates toxicity. While many candidates have been observed in model systems, their relevance to human AD brain remains unknown. This is in part due to methodological limitations preventing visualization of Aβ binding at individual synapses. To overcome this limitation, we combined two high resolution microscopy techniques: array tomography and Förster resonance energy transfer (FRET) to image over 1 million individual synaptic terminals in temporal cortex from AD (n = 11) and control cases (n = 9). Within presynapses and post-synaptic densities, oligomeric Aβ generates a FRET signal with transmembrane protein 97. Further, Aβ generates a FRET signal with cellular prion protein, and post-synaptic density 95 within post synapses. Transmembrane protein 97 is also present in a higher proportion of post synapses in Alzheimer’s brain compared to controls. We inhibited Aβ/transmembrane protein 97 interaction in a mouse model of amyloidopathy by treating with the allosteric modulator CT1812. CT1812 drug concentration correlated negatively with synaptic FRET signal between transmembrane protein 97 and Aβ. In human-induced pluripotent stem cell derived neurons, transmembrane protein 97 is present in synapses and colocalizes with Aβ when neurons are challenged with human Alzheimer’s brain homogenate. Transcriptional changes are induced by Aβ including changes in genes involved in neurodegeneration and neuroinflammation. CT1812 treatment of these neurons caused changes in gene sets involved in synaptic function. These data support a role for transmembrane protein 97 in the synaptic binding of Aβ in human Alzheimer’s disease brain where it may mediate synaptotoxicity.

Two-Photon and Multiphoton Microscopy in Anterior Segment Diseases of the Eye.

Two-photon excitation microscopy (TPM) and multiphoton fluorescence microscopy (MPM) are advanced forms of intravital high-resolution functional microscopy techniques that allow for the imaging of dynamic molecular processes and resolve features of the biological tissues of interest. Due to the cornea's optical properties and the uniquely accessible position of the globe, it is possible to image cells and tissues longitudinally to investigate ocular surface physiology and disease. MPM can also be used for the in vitro investigation of biological processes and drug kinetics in ocular tissues. In corneal immunology, performed via the use of TPM, cells thought to be intraepithelial dendritic cells are found to resemble tissue-resident memory T cells, and reporter mice with labeled plasmacytoid dendritic cells are imaged to understand the protective antiviral defenses of the eye. In mice with limbal progenitor cells labeled by reporters, the kinetics and localization of corneal epithelial replenishment are evaluated to advance stem cell biology. In studies of the conjunctiva and sclera, the use of such imaging together with second harmonic generation allows for the delineation of matrix wound healing, especially following glaucoma surgery. In conclusion, these imaging models play a pivotal role in the progress of ocular surface science and translational research.

Ionic-resolution protoacoustic microscopy: A feasibility study.

Visualizing micro- and nano-scale biological entities requires high-resolution imaging and is conventionally achieved via optical microscopic techniques. Optical diffraction limits their resolution to ∼200 nm. This limit can be overcome by using ions with ∼1 MeV energy. Such ions penetrate through several micrometers in tissues, and their much shorter de Broglie wavelengths indicate that these ion beams can be focused to much shorter scales and hence can potentially facilitate higher resolution as compared to the optical techniques. Proton microscopy with ∼1 MeV protons has been shown to have reasonable inherent contrast between sub-cellular organelles. However, being a transmission-based modality, it is unsuitable for in vivo studies and cannot facilitate three-dimensional imaging from a single raster scan. Here, we propose proton-induced acoustic microscopy (PrAM), a technique based on pulsed proton irradiation and proton-induced acoustic signal collection. This technique is capable of label-free, super-resolution, 3D imaging with a single raster scan. Converting radiation energy into ultrasound enables PrAM with reflection mode detection, making it suitable for in vivo imaging and probing deeper than proton scanning transmission ion microscopy (STIM). Using a proton STIM image of HeLa cells, a coupled Monte Carlo+k-wave simulations-based feasibility study has been performed to demonstrate the capabilities of PrAM. We demonstrate that sub-50 nm lateral (depending upon the beam size and energy) and sub-micron axial resolution (based on acoustic detection bandwidth and proton beam pulse width) can be obtained using the proposed modality. By enabling visualization of biological phenomena at cellular and subcellular levels, this high-resolution microscopic technique enhances understanding of intricate cellular processes.

Identification and control of crystalline nuclei facets imparting to the breaking of symmetry selection rules of optical phonon modes in GaP/Si (001)

The complex interfacial structural issues associated with hetero-polar epitaxial integration of GaP on Si(001) are resolved by improving the kinetics of gallium and phosphorous adatoms during the initial nucleation process. This is achieved through the use of Raman spectroscopy as a feedback mechanism. The peak intensity ratio of forbidden (transverse optical)-to-allowed (longitudinal optical) phonons of GaP under unpolarized Raman scattering is contemplated as an initial guide to ascertain the relative density of defect-mediated non-(001) GaP facets. The azimuthal-angle dependent polarized Raman spectroscopy is then applied to identify and quantify the nucleation of higher-index non-(001) ({111} and {112}) faceted islands in the nucleation layer and their propagation in the overgrown structures. The nucleation of GaP adatoms on the Silicon surface at ∼525 °C leads to a smooth surface and substantially suppresses the defect-mediated facets. The optimal mobility and controlled adsorption of adatoms of Ga and P on the substrate surface under intermediate nucleation kinetics foster the charge-neutral interface, and hence the defect-suppressed two-dimensional layer growth of GaP. The proposed Raman spectroscopy methodology emerges as a rapid and economical alternative to existing in situ reflection anisotropy spectroscopy and high-resolution transmission electron microscopy techniques for structural identification. This method of growth optimization can also be applied to other III-V polar semiconductors to achieve high-quality and efficient monolithic integration of devices on existing Si technology.

Facile synthesis and photophysical properties of combustion derived Dy3+doped Ca9La(PO4)7 nanophosphors for advanced solid-state lighting applications

Globally, the energy consumption has accelerated, which has driven the research to increase sustainable energy sources. In this context, this is the first report on the exploration of the structural and photometric aspects of Dy3+ doped Ca9La(PO4)7 i.e., CLP: Dy3+ nanophosphors for designing WLEDs economically. Herein, the solution combustion method was utilized for fabricating the desired nanophosphor, thereafter their morphological behavior, and crystallite size were studied in detail via X-ray diffraction, scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM) techniques which confirmed the rhombohedral crystal architecture with R3c space group affirming the potential of the fabricated nanomaterials in optoelectronics. CLP: Dy3+nanophosphors depicted reproducible emission spectra with peaks at 4F9/2 → 6H13/2, 15/2 attributed to intra-configurational transitions of Dy3+ ions. The increasing dopant concentration beyond 20 mol % reduced the intensity of emission peaks which could be ascribed to the dipole–dipole interactions of the neighboring ions. The optical band gap of 5.38 eV derived via Kubelka-Munk relations established their role in semiconductors. Moreover, their Commission international de I’eclairge (CIE) chromaticity coordinates were studied in detail to reveal the emission color with color purity and Correlated Color Temperature (CCT) values. All the results favored and exemplified the incredible role of CLP: Dy3+ nanophosphors for emerging future prospects in advanced optoelectronic technology.