High-quality Digital Surface Models Research Articles

Case Report: Optimization of Topographic Change Detection With UAV Structure-From-Motion Photogrammetry Through Survey Co-Alignment

High-quality digital surface models (DSMs) generated from structure-from-motion (SfM) based on imagery captured from unmanned aerial vehicles (UAVs), are increasingly used for topographic change detection. Classically, DSMs were generated for each survey individually and then compared to quantify topographic change, but recently it was shown that co-aligning the images of multiple surveys may enhance the accuracy of topographic change detection. Here, we use nine surveys over the Illgraben debris-flow torrent in the Swiss Alps to compare the accuracy of three approaches for UAV-SfM topographic change detection: 1) the classical approach where each survey is processed individually using ground control points (GCPs), 2) co-alignment of all surveys without GCPs, and 3) co-alignment of all surveys with GCPs. We demonstrate that compared to the classical approach co-alignment with GCPs leads to a minor and marginally significant increase in absolute accuracy. Moreover, compared to the classical approach co-alignment enhances the relative accuracy of topographic change detection by a factor 4 with GCPs and a factor 3 without GCPs, leading to xy and z offsets <0.1 m for both co-alignment approaches. We further show that co-alignment leads to particularly large improvements in the accuracy of poorly aligned surveys that have severe offsets when processed individually, by forcing them onto the more accurate common geometry set by the other surveys. Based on these results we advocate that co-alignment, preferably with GCPs to ensure a high absolute accuracy, should become common-practice in high-accuracy UAV-SfM topographic change detection studies for projects with sufficient stable areas.

Research on Multiview Stereo Mapping Based on Satellite Video Images

In recent years, video satellite technology has greatly developed, and satellite video is captured using this technology. Because video satellites in motion are consistently aimed at certain areas, satellite video is usually composed of a series of frame images of the same area with different viewing angles; these satellite video images have different base-height ratios with each other, which makes multiview stereo mapping possible. This paper presents a method of multiview stereo mapping based on satellite video images to generate a digital surface model (DSM), digital elevation model (DEM), and digital ortho map (DOM) and analyzes the influence of different numbers and different viewing angles of satellite video images involved in multiview stereo mapping on the quality of the results. Satellite video images of Urumqi, China, captured by the “Jilin-1” video-03 satellite, were used as experimental data for the verification of the proposed method, and the results of the experiment show that: a high-quality DSM, DEM, and DOM can be generated by multiview stereo mapping based on two or more satellite video images, and the elevation precision and plane precision of the DEM results are 2.751 m and 2.419 m, respectively; such as in traditional stereo mapping, the larger the base-height ratio of the images involved in the calculation is, the higher the elevation precision of the DSM results will be within a certain extent. When the images participating in the calculation comprise images viewed from the nadir direction, forward direction and backward direction at the same time, DSM results with better building textures can be generated with high precision, and as the number of satellite video images increases, the building textures in the DSM results are optimized.

MORPHOLOGICAL ANALYSIS OF LANDSLIDES IN EXTREME TOPOGRAPHY BY UAS-SfM: DATA ACQUISITION, 3D MODELS AND CHANGE DETECTION

Abstract. Landslides are one major kind of natural disasters and geomorphological processes on Earth’s surface. Accurate geodetic observations are crucial for understanding morphological changes, providing a quantitative basis of further research in surface process and hazard management. In recent years, the development of UAVs and SfM technology enhance research to build high quality digital surface models of landforms with low budget and efficiency. In areas of extreme topography where landslides occur on steep slopes, however, it is required to specifically design the UAV-SfM workflow to keep the data quality. This study aims to use UAS-SfM workflow to develop a low-cost, efficient methodology to detect detailed morphological change of landslide morphology in extreme topography. The study focuses on examining results of different flight design and GCPs distribution geometry, which are important components in the workflow. In addition, we applied a mathematical model to compare point clouds to calculate volumetric change of the landslide with reduced distortion.

3D reconstruction from multi-view VHR-satellite images in MicMac

This work addresses the generation of high quality digital surface models by fusing multiple depths maps calculated with the dense image matching method. The algorithm is adapted to very high resolution multi-view satellite images, and the main contributions of this work are in the multi-view fusion. The algorithm is insensitive to outliers, takes into account the matching quality indicators, handles non-correlated zones (e.g. occlusions), and is solved with a multi-directional dynamic programming approach. No geometric constraints (e.g. surface planarity) or auxiliary data in form of ground control points are required for its operation. Prior to the fusion procedures, the RPC geolocation parameters of all images are improved in a bundle block adjustment routine. The performance of the algorithm is evaluated on two VHR (Very High Resolution)-satellite image datasets (Pléiades, WorldView-3) revealing its good performance in reconstructing non-textured areas, repetitive patterns, and surface discontinuities.

URBAN MODELLING PERFORMANCE OF NEXT GENERATION SAR MISSIONS

Abstract. In synthetic aperture radar (SAR) technology, urban mapping and modelling have become possible with revolutionary missions TerraSAR-X (TSX) and Cosmo-SkyMed (CSK) since 2007. These satellites offer 1m spatial resolution in high-resolution spotlight imaging mode and capable for high quality digital surface model (DSM) acquisition for urban areas utilizing interferometric SAR (InSAR) technology. With the advantage of independent generation from seasonal weather conditions, TSX and CSK DSMs are much in demand by scientific users. The performance of SAR DSMs is influenced by the distortions such as layover, foreshortening, shadow and double-bounce depend up on imaging geometry. In this study, the potential of DSMs derived from convenient 1m high-resolution spotlight (HS) InSAR pairs of CSK and TSX is validated by model-to-model absolute and relative accuracy estimations in an urban area. For the verification, an airborne laser scanning (ALS) DSM of the study area was used as the reference model. Results demonstrated that TSX and CSK urban DSMs are compatible in open, built-up and forest land forms with the absolute accuracy of 8–10 m. The relative accuracies based on the coherence of neighbouring pixels are superior to absolute accuracies both for CSK and TSX.

Automatic Buildings Extraction From LiDAR Data in Urban Area by Neural Oscillator Network of Visual Cortex

Researchers have extensively applied Locally Excitatory Globally Inhibitory Oscillator Networks (LEGION) for segmentation. These networks are neural oscillator networks based on biological frameworks, in which each oscillator has excitatory lateral connections to the oscillators in its local neighbourhood, as well as a connection to a global inhibitor. In this paper, we develop a modified LEGION segmentation to extract buildings from high-quality digital surface models (DSMs). The extraction is implemented without assumptions on the underlying structures in the DSM data and without prior knowledge of the number of regions. For complex information hidden in the generated DSM of an urban area, grey level co-occurrence matrix homogeneity is used to measure DSM height texture. We then use this homogeneity to distinguish buildings from trees and identify major oscillator blocks in target buildings, instead of using lateral potential. To segment pixels into different groups, we calculate the weight of the global inhibitor (Wz) from DSM complexity. Building boundaries are traced and regularised after extraction from the segmented DSM. A least squares solution with perpendicular constraints for determining regularised rectilinear building boundaries is proposed, and arc line fitting is performed. This paper presents the concept, algorithms, and procedures of the proposed approach. Experimental results on the Vaihingen region studied in the ISPRS test project are also discussed.

VALIDATION OF DEMs DERIVED FROM HIGH RESOLUTION SAR DATA: A CASE STUDY ON BARCELONA

Abstract. In recent years, Synthetic Aperture Radar (SAR) data have been widely used for scientific applications and several SAR missions were realized. The active sensor principle and the signal wavelength in the order of centimeters provide all-day and all-weather capabilities, respectively. The modern German TerraSAR-X (TSX) satellite provides high spatial resolution down to one meter. Based on such data SAR Interferometry may yield high quality digital surface models (DSMs), which includes points located on 3d objects such as vegetation, forest, and elevated man-made structures. By removing these points, digital elevation model (DEM) representing the bare ground of Earth is obtained. The primary objective of this paper is the validation of DEMs obtained from TSX SAR data covering Barcelona area, Spain, in the framework of a scientific project conducted by ISPRS Working Group VII/2 "SAR Interferometry" that aims the evaluation of DEM derived from data of modern SAR satellite sensors. Towards this purpose, a DSM was generated with 10 m grid spacing using TSX StripMap mode SAR data and converted to a DEM by filtering. The accuracy results have been presented referring the comparison with a more accurate (10 cm–1 m) digital terrain model (DTM) derived from large scale photogrammetry. The results showed that the TSX DEM is quite coherent with the topography and the accuracy is in between ±8–10 m. As another application, the persistent scatterer interferometry (PSI) was conducted using TSX data and the outcomes were compared with a 3d city model available in Google Earth, which is known to be very precise because it is based on LIDAR data. The results showed that PSI outcomes are quite coherent with reference data and the RMSZ of differences is around 2.5 m.