High-performance Non-fullerene Solar Cells Research Articles

Alkoxy-Substituted Anthrabisthiadiazole–Benzodithiophene-Based Wide-Band-Gap Semiconducting Polymers for High-Performance Non-Fullerene Solar Cells

Alkoxy-Substituted Anthrabisthiadiazole–Benzodithiophene-Based Wide-Band-Gap Semiconducting Polymers for High-Performance Non-Fullerene Solar Cells

Impact of length of branched alkyl side chains on thiazolothiazole-based small molecular acceptors in non-fullerene polymer solar cells.

It has been reported that the length of branched alkyl side chains on fused-ring electron acceptors confers different impacts on properties versus solubility of BJH blends. However, because this impact on a non-fused acceptor backbone has rarely been studied, we examined the impact of molecular optimization from alkyl chain tuning based on non-fused thiazolothiazole small-molecule acceptors. The length of the side chain on the thiophene bridge was modified from 2-butyloctyl to 2-ethylhexyl, which corresponds to small molecules TTz3(C4C6) and TTz3(C2C4), respectively. Compared with the reported TTz3(C6C8) with long alkyl side chains, TTz3(C4C6) and TTz3(C2C4) exhibited stronger molecular aggregation, higher absorption coefficients, and greater redshifted UV absorption. Unexpectedly, after the alkyl chain was slightly shortened in this type of acceptor system, devices were successfully fabricated, but it was necessary to reduce the blending concentration at low rotation speeds due to the sharp decrease in the solubility of corresponding acceptor materials. Thus, the obtained unfavorable thickness and morphology of the active layer caused a decrease in Jsc and FF. As a consequence, TTz3(C4C6)- and TTz3(C2C4)-based devices showed an unsatisfactory power conversion efficiency of 6.02% and 2.71%, respectively, when donors were paired with the wide bandgap donor J71, which is inferior to that of TTz3(C6C8)-based devices (8.76%). These results indicate that it is challenging to determine the limit of the adjustable range of side chains to modify non-fused thiazolothiazole small-molecule acceptors for high-performance non-fullerene solar cells.

Delicately Controlled Polymer Orientation for High-Performance Non-Fullerene Solar Cells with Halogen-Free Solvent Processing.

Molecular orientation in polymer solar cells (PSCs) is a critical subject of investigation that promotes the quality of bulk heterojunction morphology and power conversion efficiency (PCE). Herein, the intrinsic polymer orientation transition can be found upon delicate control over the branching point position of the irregular alkoxy side chain in difluoroquinoxaline-thiophene-based conjugated polymers. Three polymers with branching points at the third, fourth, and fifth positions away from the backbone were synthesized and abbreviated as PHT3, PHT4, and PHT5, respectively. Temperature-dependent absorption behavior manifests the polymer aggregation ability in the order of PHT3 < PHT4 < PHT5. Surprisingly, the polymer orientation transition from typical face-on to edge-on emerged between PHT4 and PHT5, as evidenced by X-ray-scattering analysis. The enhanced face-on crystallinity of PHT4 endowed the o-xylene-processed PHT4:IT-4Cl-based devices with the highest PCE of 13.40%. For PHT5 with stronger aggregation, the related o-xylene-processed PSCs still showed a good PCE of 12.66%. Our results demonstrate that a delicate polymer orientation transition could be realized through a precisely controlled strategy of the side chain, yielding green-solvent-processed high-performance PSCs.

Comparing Benzodithiophene Unit with Alkylthionaphthyl and Alkylthiobiphenyl Side-Chains in Constructing High-Performance Nonfullerene Solar Cells.

Using single-bonded and fused aromatic rings are two methods for extending the π-conjugation in the vertical direction of benzo [1,2-b:4,5-b′] dithiophene (BDT) unit. To investigate which method is more efficient in nonfullerene systems, two novel polymers based on alkylthionaphthyl and alkylthiobiphenyl substituted BDT named PBDTNS-FTAZ and PBDTBPS-FTAZ are designed and synthesized. Two polymers only exhibit small differences in structure, but huge differences in photovoltaic properties. They are studied by blended with 3,9-bis(2-methylene-(3-(1,1-dicyanomethylene)indanone)-5,5,11,11-tetrakis(4-hexylphenyl)dithieno [2,3-d’:2,3’-d’]-s-indaceno [1,2-b:5,6-b’] dithiophene (ITIC). The device based on PBDTNS-FTAZ:ITIC showed the best power conversion efficiency (PCE) of 9.63% with the Voc of 0.87 V, a Jsc of 18.06 mA/cm2 and a fill factor of 61.21%, while the PBDTBPS-FTAZ:ITIC only exhibit a maximum PCE of 7.79% with a Voc of 0.86 V, a Jsc of 16.24 mA/cm2 and a relatively low fill factor of 55.92%. Therefore, extending π-conjugation with alkylthionaphthyl is more effective against constructing nonfullerene solar cells.

High-Efficiency Perovskite Quantum Dot Hybrid Nonfullerene Organic Solar Cells with Near-Zero Driving Force.

To take advantages of the intense absorption and fluorescence, high charge mobility, and high dielectric constant of CsPbI3 perovskite quantum dots (PQDs), PQD hybrid nonfullerene organic solar cells (OSCs) are fabricated. Addition of PQDs leads to simultaneous enhancement of open-circuit voltage (VOC ), short-circuit current density (JSC ), and fill factor (FF); power conversion efficiencies are boosted from 11.6% to 13.2% for PTB7-Th:FOIC blend and from 15.4% to 16.6% for PM6:Y6 blend. Incorporation of PQDs dramatically increases the energy of the charge transfer state, resulting in near-zero driving force and improved VOC . Interestingly, at near-zero driving force, the PQD hybrid OSCs show more efficient charge generation than the control device without PQDs, contributing to enhanced JSC , due to the formation of cascade band structure and increased molecular ordering. The strong fluorescence of the PQDs enhances the external quantum efficiency of the electroluminescence of the active layer, which can reduce nonradiative recombination voltage loss. The high dielectric constant of the PQDs screens the Coulombic interactions and reduces charge recombination, which is beneficial for increased FF. This work may open up wide applicability of perovskite quantum dots and an avenue toward high-performance nonfullerene solar cells.

A Maverick Asymmetrical Backbone with Distinct Flanked Twist Angles Modulating the Molecular Aggregation and Crystallinity for High Performance Nonfullerene Solar Cells

AbstractIn this work, a new asymmetrical backbone thienobenzodithiophene (TBD) containing four aromatic rings is designed, and then four polymers PTBD‐BZ, PTBD‐BDD, PTBD‐FBT, and PTBD‐Tz are synthesized. The planar and high degree of π‐conjugation configuration can guarantee effective charge carrier transport and the distinct flanked dihedral angles between the TBD core and conjugated side chain can subtly regulate the molecular aggregation and crystallinity. The four polymer/3,9‐bis(2‐methylene‐(3‐(1,1‐dicyanomethylene)‐indanone)‐5,5,11,11‐tetrakis(4‐hexylphenyl)‐dithieno[2,3‐d:2′,3′‐d′]‐s‐indaceno[1,2‐b:5,6‐b′]‐dithiophene (ITIC) blending films exhibit predominantly face‐on orientation. The photovoltaic devices based on wide bandgap polymers PTBD‐BZ and PTBD‐BDD achieve power conversion efficiencies (PCEs) as high as 12.02% and 11.39% without any post‐treatment. For the medium bandgap polymers PTBD‐FBT and PTBD‐Tz, the devices also show good PCEs of 10.18% and 11.02% with high VOC of 0.94 and 1.02 V, respectively, which indicates simultaneously achieving a VOC &gt; 1 V and a high JSC is feasible to further improve the PSCs' performance by modifying this new backbone. This work reveals that the versatile asymmetric backbone is an excellent moiety to construct light‐harvesting copolymers and to modulate the microstructure for highly efficient PSCs.

An effective strategy for controlling the morphology of high-performance non-fullerene polymer solar cells without post-treatment: employing bare rigid aryl rings as lever arms in new asymmetric benzodithiophene

Weakening the entanglements between polymer chains enables the creation of high-performance non-fullerene solar cells without post-treatment.

Enhancing the performance of non-fullerene solar cells with polymer acceptors containing large-sized aromatic units

In this work, we develop four diketopyrrolopyrrole-based polymer acceptors for application in polymer-polymer solar cells. The polymer acceptors contain different-sized aromatic units, from small thiophene to benzodithiophene and large alkylthio-benzodithiophene units. Although the polymer acceptor with large-sized groups shows small LUMO offset and low energy loss when blended with the donor polymer PTB7-Th, the corresponding solar cells can achieve a high power conversion efficiency (PCE) of 3.1% due to high photocurrent. In contrast, the polymer acceptor with small thiophene units only provides a low PCE of 0.14% in solar cells. These results indicate that polymer acceptors with large-sized aromatic units can be potentially used into high performance non-fullerene solar cells.

High-Performance Nonfullerene Polymer Solar Cells based on Imide-Functionalized Wide-Bandgap Polymers.

High-performance nonfullerene polymer solar cells (PSCs) are developed by integrating the nonfullerene electron-accepting material 3,9-bis(2-methylene-(3-(1,1-dicyanomethylene)-indanone))-5,5,11,11-tetrakis(4-hexylphenyl)-dithieno[2,3-d:2',3'-d']-s-indaceno[1,2-b:5,6-b']dithiophne) (ITIC) with a wide-bandgap electron-donating polymer PTzBI or PTzBI-DT, which consists of an imide functionalized benzotriazole (TzBI) building block. Detailed investigations reveal that the extension of conjugation can affect the optical and electronic properties, molecular aggregation properties, charge separation in the bulk-heterojunction films, and thus the overall photovoltaic performances. Single-junction PSCs based on PTzBI:ITIC and PTzBI-DT:ITIC exhibit remarkable power conversion efficiencies (PCEs) of 10.24% and 9.43%, respectively. To our knowledge, these PCEs are the highest efficiency values obtained based on electron-donating conjugated polymers consisting of imide-functionalized electron-withdrawing building blocks. Of particular interest is that the resulting device based on PTzBI exhibits remarkable PCE of 7% with the thickness of active layer of 300 nm, which is among the highest values of nonfullerene PSCs utilizing thick photoactive layer. Additionally, the device based on PTzBI:ITIC exhibits prominent stability, for which the PCE remains as 9.34% after thermal annealing at 130 °C for 120 min. These findings demonstrate the great promise of using this series of wide-bandgap conjugated polymers as electron-donating materials for high-performance nonfullerene solar cells toward high-throughput roll-to-roll processing technology.

Propeller-Shaped Acceptors for High-Performance Non-Fullerene Solar Cells: Importance of the Rigidity of Molecular Geometry

This paper describes the synthesis and application of βTPB6 and βTPB6-C as electron acceptors for organic solar cells. Compound βTPB6 contains four covalently bonded PDIs with a BDT-Th core at the β-position. The free rotation of PDIs renders βTPB6 with varying molecular geometries. The cyclization of βTPB6 yields βTPB6-C with high rigidity of the molecular geometry and enlarged conjugated skeleton. The inverted solar cells based on βTPB6-C and PTB7-Th as the donor polymer exhibited the highest efficiency of 7.69% with Voc of 0.92 V, Jsc of 14.9 mAcm–2, and FF of 0.56, which is 31% higher than that for βTPB6 based devices. The larger fraction of βTPB6-C and PTB7-Th than that of βTPB6:PTB7-Th in a blend film takes a face-on orientation packing pattern for π-systems that benefits the charge transport and hence higher PCE value than that for βTPB6:PTB7-Th. It was also found that a proper DIO:DPE additive further enhances this trend, which results in an increase of the PCE value for βTPB6-C:PTB7-Th while decr...

Performance limitations in thieno[3,4-c]pyrrole-4,6-dione-based polymer:ITIC solar cells.

We report a systematic study of the efficiency limitations of non-fullerene organic solar cells that exhibit a small energy loss (Eloss) between the polymer donor and the non-fullerene acceptor. To clarify the impact of Eloss on the performance of the solar cells, three thieno[3,4-c]pyrrole-4,6-dione-based conjugated polymers (PTPD3T, PTPD2T, and PTPDBDT) are employed as the electron donor, which all have complementary absorption spectra compared with the ITIC acceptor. The corresponding photovoltaic devices show that low Eloss (0.54 eV) in PTPDBDT:ITIC leads to a high open-circuit voltage (Voc) of 1.05 V, but also to a small quantum efficiency, and in turn photocurrent. The high Voc or small energy loss in the PTPDBDT-based solar cells is a consequence of less non-radiative recombination, whereas the low quantum efficiency is attributed to the unfavorable micro-phase separation, as confirmed by the steady-state and time-resolved photoluminescence experiments, grazing-incidence wide-angle X-ray scattering, and resonant soft X-ray scattering (R-SoXS) measurements. We conclude that to achieve high performance non-fullerene solar cells, it is essential to realize a large Voc with small Eloss while simultaneously maintaining a high quantum efficiency by manipulating the molecular interaction in the bulk-heterojunction.