High Conductivity Levels Research Articles

Investigation of Possible Sources of Electrodermal Activity in Surgical Personnel to Assess Workplace Stress Levels.

The aim of this study was to evaluate alternative measurement points to assess stress levels during surgery, given that taking electrodermal activity (EDA) measurements from the palms, a commonly used standard, is impractical in surgical contexts. A combination of mentally challenging tasks on a laparoscopy trainer (LapSim) and physically challenging sports exercises were performed by a group of participants. During these tasks, EDA was measured at three different locations: the fingers, toes, and shoulder/neck area. Additionally, an electrocardiogram was used as an objective measure of stress levels. The findings indicated that EDA measurements taken at the toes produced similar high skin conductance levels to measurements taken at the palms. However, significantly lower skin conductance levels were observed at the shoulder. Despite this, the cross-correlation of EDA data revealed high correlation coefficients (above 0.96) between both the toe and shoulder measurements when compared to the palm data. The study concludes that both the toes and the shoulder/neck area serve as viable alternative locations for assessing occupational stress levels in surgical personnel. This assertion is supported by the similarity of the data produced by these methods to that of the standard finger-based technique, with the latter still being identified as the most sensitive method for capturing EDA. Subsequently, these findings attest to the potential for practical adaptation of this technique in surgical contexts.

Effect of the Root Endophytic Fungus Piriformospora indica on Strawberry Growth, Fruit Quality and Physiological Traits Under Elevated Electrical Conductivity

Strawberries are sensitive to abiotic stresses such as salinity, high levels of electrical conductivity, and nutrient imbalances. The mutualistic endophytic fungus Piriformospora indica has significant potential to be used in improving crop production under adverse conditions, with a large host range. However, greenhouse production requires novel tactics to improve the efficiency of saline water irrigation in areas with limited freshwater resources. This study was conducted at the National Research and Development Center for Sustainable Agriculture (Estidamah), KSA, to investigate the impact of P. indica colonization on the growth, photosynthesis traits, productivity, and fruit quality of Fragraria × ananassa Duch cv. Festival strawberry grown in pots and irrigated with two electrical conductivity (EC) nutrient solutions of 1.5 and 3.0 dS/m. The results showed that higher-EC-nutrient solution clearly reduced growth and early yield and improved vitamin C, TSS, and anthocyanin of strawberry in comparison to low-EC-nutrient solution. On the other hand, P. indica colonization significantly increased plant height, shoot fresh weight, root length, and early yield of plants grown under high-EC-nutrient solution with no impact on fruit quality. Obviously, the symbiosis between strawberry roots and P. indica enhanced chlorophyll content, photosynthetic rate, stomatal conductance, and transpiration rate, as well as antioxidant activity such as proline, malondialdehyde, catalase, superoxide dismutase, and peroxidase under higher-EC-nutrient solution. Our study indicated that P. indica might be used as a sustainable tool for strawberry production in arid and semiarid zones, to mitigate the negative impacts of higher-EC-nutrient solution.

Two‐Dimensional Layered Topological Semimetals for Advanced Electronics and Optoelectronics

AbstractDue to the outstanding physical properties and the integrated characteristics, such as the gapless band structure, high state density, high conductivity, dangling‐bond‐free surface, and tunable Fermi level, two‐dimensional layered topological semimetals (2D LTSMs) exhibit a promising application prospect for including electrode contact and terahertz detection. Despite the surging in attention, a comprehensive strategy is still crucial to meet the necessary conditions for the practical application of 2D LTSMs. According to the fermion types and the band structures, 2D LTSMs can be divided into Dirac semimetals, Weyl semimetals, and nodal‐line semimetals. This review comprehensively encapsulates the intrinsic properties, typical synthesis methods, and applications in electronics and optoelectronics about these 2D LTSMs. To establish the fundamental theory, typical crystal structures, and physical properties of different 2D LTSMs are summarized at first. The effective synthesis strategies including exfoliation, molecular beam epitaxy, and vapor deposition are analyzed systematically. Finally, the article emphasizes the exploration of applications, significant challenges, and promising development directions of 2D LTSMs, which will drive 2D LTSMs to become the promisingly leading technology for next‐generation electronic and optoelectronic systems.

Conductance Channels in a Single-Entity Enzyme.

For a long time, the prevailing view in the scientific community was that proteins, being complex macromolecules composed of amino acid chains linked by peptide bonds, adopt folded structure with insulating or semiconducting properties, with high bandgaps. However, recent discoveries of unexpectedly high conductance levels, reaching values in the range of dozens of nanosiemens (nS) in proteins, have challenged this conventional understanding. In this study, we used scanning tunneling microscopy (STM) to explore the single-entity conductance properties of enzymatic channels, focusing on bilirubin oxidase (BOD) as a model metalloprotein. By immobilizing BOD on a conductive carbon surface, we discern its preferred orientation, facilitating the formation of electronic and ionic channels. These channels show efficient electron transport (ETp), with apparent conductance up to the 15 nS range. Notably, these conductance pathways are localized, minimizing electron transport barriers due to solvents and ions, underscoring BOD's redox versatility. Furthermore, electron transfer (ET) within the BOD occurs via preferential pathways. The alignment of the conductance channels with hydrophilicity maps, molecular vacancies, and regions accessible to electrolytes explains the observed conductance values. Additionally, BOD exhibits redox activity, with its active center playing a critical role in the ETp process. These findings significantly advance our understanding of the intricate mechanisms that govern ETp processes in proteins, offering new insights into the conductance of metalloproteins.

Different characteristics of the soil in marmot habitats might be one of the factors that influcting Yersinia pestis prevalent in which than pikas.

Marmots are recognized as host animals for plague caused by Yersinia pestis infection. It is unclear that why plague prevalent in marmot rather than other rodents like pikas in the same habitats. This study aims to analyze the differences of the soil characteristics around marmots and pikas burrows to explore the soils factors impacting on different epidemic intensities of Yersinia pestis in these two rodents. Soil samples were collected from within and around marmot and pika burrows, as well as from the nearby areas not inhabited by them and Chinese baseline soil properties as control groups, in the Qilian Mountains of Gansu Province, China. The physicochemical properties and the bacterial 16S rRNA were measured to analyze the characteristics of soils from different groups. Subsequently, the data were analyzed using R studio. The analysis revealed that marmot habitats exhibited distinct soil characteristics, including lower organic matter and alkaline hydrolyzed nitrogen, but higher electrical conductivity and total soluble salts. And soil in marmot areas tended to have higher concentrations of nickel, chromium, and iron, also lower levels of zinc and selenium. Additionally, the alpha diversity of soil microorganisms in marmot habitats was significantly low. Simultaneously, redundancy analysis was conducted, which showed that the low alpha diversity of marmot-soil was influenced by its physicochemical properties. The alpha diversity of the soil was positively correlated with EC, TSS, Na, and Cr, etc., while it was negatively correlated with AHN, OM, Se, Zn, and Fe, etc. These characteristics in marmot habitats, including low levels of organic matter, alkaline hydrolyzed nitrogen, zinc, selenium, and bacterial alpha diversity, as well as high levels of electrical conductivity, total soluble salts, iron, and nickel, played a crucial role in the spread of plague. It was discovered that the unique characteristics of marmot-soils provided essential elements necessary for the survival of Yersinia pestis, including high levels of Fe and Ca, or facilitated the spread of plague. Thus, the transmission of the plague was facilitated.

Sustainable agriculture through qanat systems in Karabakh: Water and soil characteristics in the context of climate change

This study investigates the water quality and soil characteristics associated with qanat systems in the Cebrail district of the Karabakh region, Azerbaijan. Qanat systems, traditional underground channels designed for water transport, play a crucial role in providing reliable water sources for drinking and irrigation. Water and soil samples were collected from seven qanat systems and analyzed for various physicochemical properties. Water quality parameters included pH, electrical conductivity, hardness, mineralization, and concentrations of calcium, magnesium, sodium, and other ions. Soil analyses focused on pH, electrical conductivity, organic matter content, salinization degree, and the presence of key ions like sulfate and nitrate. The results indicated that qanat water is generally of high quality, with pH levels suitable for both drinking and irrigation. However, some qanat systems exhibited high electrical conductivity and mineralization levels, suggesting potential salinity issues for sensitive crops. Soil samples showed favorable conditions for agriculture, with good pH levels, low salinity, and high organic matter content. The analysis revealed a significant interaction between water quality and soil characteristics, emphasizing the importance of integrated management practices. In the context of climate change, the sustainability of qanat systems is critical. Recommendations include regular monitoring of water and soil quality, soil amendments to mitigate salinity, efficient irrigation techniques, and the use of climate-resilient infrastructure. This study underscores the importance of qanat systems in arid and semi-arid regions and provides practical recommendations for sustainable land and water resource management, enhancing the socio-economic well-being of local communities.

Impact of parametric seasonal variations on water quality in the Crocodile River and Inyaka Dam in the Mpumalanga Province, South Africa

This study assessed seasonal variations in water quality and their impact on the Inyaka Dam and Crocodile River in Mpumalanga Province, South Africa. A total of 206 water samples were collected across four seasons to analyse parameters including pH, turbidity, electrical conductivity (EC), temperature, Manganese (Mn), Iron (Fe), phosphate (PO43−), nitrate-nitrogen (NO3-N), E. coli, total coliforms, faecal streptococci, and Bifidobacteria. Principal component analysis (PCA) and Pearson correlation identified major pollutants and their seasonal variations, while cluster analysis grouped water quality by parameter fluctuations.Findings indicated that water quality in both the Inyaka Dam and the Crocodile River exceeded permissible limits. In the Inyaka Dam, summer rainfall (202.68 mm) spurred microbial growth, including E. coli and Bifidobacteria, while winter saw elevated levels of PO43−, EC, Fe, and NO3-N. The Crocodile River exhibited its poorest water quality in summer, with high levels of conductivity, turbidity, Fe, Mn, and NO3-N, driven largely by rainfall. Winter pollution in the river was marked by E. coli, PO43−, total coliforms, NO3-N, and Bifidobacteria.The study highlights significant pollution in the Crocodile River, particularly in summer, linked to rainfall and effluent discharges. Microbial pollution persisted across seasons, influenced by both weather and point-source contamination. The winter season exacerbated water quality deterioration in the Crocodile River due to reduced flow, while Inyaka Dam's winter pollution was attributed to lake stratification.

Hydrogen storage potential of XNiH3 (X= Sr and Ba) compounds: A comprehensive DFT analysis

The increasing need for sustainable energy solutions emphasizes the significance of effective hydrogen storage materials. This work provides a thorough analysis using density functional theory (DFT) to assess the capacity of XNiH3 (X = Sr and Ba) compounds, where X denotes strontium (Sr) and barium (Ba), for storing hydrogen. We employed the Cambridge Serial Total Energy Package (CASTEP) approach to optimize the geometries and determine the structural, electrical, optical, and mechanical properties of SrNiH3 and BaNiH3. The findings indicate that SrNiH3 demonstrates a higher gravimetric hydrogen storage capacity (2.03 %) in comparison to BaNiH3 (1.52 %). Both compounds exhibit metallic behavior, characterized by the absence of band gaps, which indicates a high level of electrical conductivity. The optical investigations reveal prominent absorption peaks at 25.32 eV for SrNiH3 and 18.82 eV for BaNiH3, accompanied by substantial energy loss functions and refractive behaviors. Based on mechanical studies, it has been determined that both compounds are mechanically stable. However, SrNiH3 exhibits a larger bulk modulus and Young's modulus compared to BaNiH3. The results highlight the potential of SrNiH3 and BaNiH3 as suitable options for storing hydrogen, which can contribute to the progress of clean energy technology.

Implication of heavy metal(loid)s contamination for human health and preliminary application of water treatment in floodplain area along Mekong River, Lao PDR

Groundwater is widely used for domestic purposes, especially as a reliable source of drinking water in rural areas of the Lao People’s Democratic Republic (Lao PDR). This preliminary study aims to examine heavy metal(loid)s contamination leading to human health risks while also focusing on a method that can improve drinking water quality in floodplain areas along the Mekong River in Lao PDR. Groundwater and surface water samples were collected during the monsoon season in 2022 in Attapeu and Champasak provinces. Heavy metal(loid)s concentrations and human health risks were investigated using inductively coupled plasma mass spectrometry (ICP-MS) and the USEPA method, respectively. A nanofiltration membrane technique was introduced to optimize the quality of groundwater. Results showed that groundwater quality was significantly poor (p < 0.05), particularly in Attapeu province, with high levels of electrical conductivity, total dissolved solids, and manganese, exceeding WHO standards of 400 µS cm−1, 300 mg L−1, and 80 µg L−1, respectively. With the groundwater ingestion pathway, children were found to be more vulnerable to non-carcinogenic risk than adults (Hazard Quotient, Hazard Index >1), but adults had a higher carcinogenic risk (Incremental Lifetime Cancer Risk >1E-04). The removal of fecal bacteria and heavy metal(loid)s was achieved using the nanofiltration membrane, demonstrating its potential as a practical point-of-use technology to provide cleaner water sources and enhance the health status of Lao residents.

Free-Standing, Water-Resistant, and Conductivity-Enhanced PEDOT:PSS Films from In Situ Polymerization of 3-Hydroxymethyl-3-Methyl-Oxetane.

Free-standing films based on conducting polymers, such as poly(3,4-ethylenedioxythiophene): poly(styrene sulfonate) (PEDOT:PSS), offer many benefits over traditional metal electrodes for applications in flexible electronics. However, to ensure structural integrity when contacting aqueous environments and high levels of electrical conductivity, solution-processed polymers require additives that act as crosslinking agents and conductivity enhancers. In this work, a new approach is presented to fabricate water-resistant free-standing films of PEDOT:PSS and simultaneously increase their conductivity, using an oxetane compound as an additive. It is shown that at moderate temperatures, oxetane polymerizes within the PEDOT:PSS acidic medium, forming hydroxymethyl-substituted polyether compounds that form a network upon crosslinking with PSS. The polymer composite films show self-sustainability, structural stability in aqueous environments, and enhanced conductivity. Finally, the potential of the free-standing films as health-monitoring electrodes, specifically for human electrocardiography, is explored.

Impact of Thermochemical Treatments on Electrical Conductivity of Donor-Doped Strontium Titanate Sr(Ln)TiO3 Ceramics.

The remarkable stability, suitable thermomechanical characteristics, and acceptable electrical properties of donor-doped strontium titanates make them attractive materials for fuel electrodes, interconnects, and supports of solid oxide fuel and electrolysis cells (SOFC/SOEC). The present study addresses the impact of processing and thermochemical treatment conditions on the electrical conductivity of SrTiO3-derived ceramics with moderate acceptor-type substitution in a strontium sublattice. A-site-deficient Sr0.85La0.10TiO3-δ and cation-stoichiometric Sr0.85Pr0.15TiO3+δ ceramics with varying microstructures and levels of reduction have been prepared and characterized by XRD, SEM, TGA, and electrical conductivity measurements under reducing conditions. The analysis of the collected data suggested that the reduction process of dense donor-doped SrTiO3 ceramics is limited by sluggish oxygen diffusion in the crystal lattice even at temperatures as high as 1300 °C. A higher degree of reduction and higher electrical conductivity can be obtained for porous structures under similar thermochemical treatment conditions. Metallic-like conductivity in dense reduced Sr0.85La0.10TiO3-δ corresponds to the state quenched from the processing temperature and is proportional to the concentration of Ti3+ in the lattice. Due to poor oxygen diffusivity in the bulk, dense Sr0.85La0.10TiO3-δ ceramics remain redox inactive and maintain a high level of conductivity under reducing conditions at temperatures below 1000 °C. While the behavior and properties of dense reduced Sr0.85Pr0.15TiO3+δ ceramics with a large grain size (10-40 µm) were found to be similar, decreasing grain size down to 1-3 µm results in an increasing role of resistive grain boundaries which, regardless of the degree of reduction, determine the semiconducting behavior and lower total electrical conductivity of fine-grained Sr0.85Pr0.15TiO3+δ ceramics. Oxidized porous Sr0.85Pr0.15TiO3+δ ceramics exhibit faster kinetics of reduction compared to the Sr0.85La0.10TiO3-δ counterpart at temperatures below 1000 °C, whereas equilibration kinetics of porous Sr0.85La0.10TiO3-δ structures can be facilitated by reductive pre-treatments at elevated temperatures.

Solid‐State Processing of Nascent Disentangled UHMWPE Reactor Powders Mixed with Carbon Nanoparticles

AbstractAspects of solid‐state processing of nascent disentangled ultra‐high‐molecular‐weight polyethylene (UHMWPE) powders of different syntheses mixed with electrically conductive carbon nanoparticles (NPs) of various types are studied. Effect of multiple parameters of the processing procedures on the electrophysical characteristics of the composite samples is investigated. Such parameters include time of preliminary ultrasonication (US) of NPs, time of US of UHMWPE/NPs mixtures, molding time, temperature, and pressure, deformation degree, etc. It is observed that by selecting optimal values of such parameters it is possible to obtain samples of composites with an extremely segregated structure made of the NPs, with NPs distributed evenly on the surfaces of the compacted UHMWPE powder particles. This ensures high levels of conductivity at very low values of NPs content. The segregated structure is retained when the composites are strengthened using the solid‐state uniaxial shear deformation process. While conductivity of most of the composites filled with various types of NPs monotonously decreases with the deformation ratio, conductivity of the composites filled with exceptionally long double‐walled carbon nanotubes is maintained. The processed oriented composites are also characterized by high EMR shielding properties, as well as interesting temperature dependencies of the electrical conductivity.

Programmable Retention Characteristics in MoS2-Based Atomristors for Neuromorphic and Reservoir Computing Systems.

In this study, we investigate the coexistence of short- and long-term memory effects owing to the programmable retention characteristics of a two-dimensional Au/MoS2/Au atomristor device and determine the impact of these effects on synaptic properties. This device is constructed using bilayer MoS2 in a crossbar structure. The presence of both short- and long-term memory characteristics is proposed by using a filament model within the bilayer transition-metal dichalcogenide. Short- and long-term properties are validated based on programmable multilevel retention tests. Moreover, we confirm various synaptic characteristics of the device, demonstrating its potential use as a synaptic device in a neuromorphic system. Excitatory postsynaptic current, paired-pulse facilitation, spike-rate-dependent plasticity, and spike-number-dependent plasticity synaptic applications are implemented by operating the device at a low-conductance level. Furthermore, long-term potentiation and depression exhibit symmetrical properties at high-conductance levels. Synaptic learning and forgetting characteristics are emulated using programmable retention properties and composite synaptic plasticity. The learning process of artificial neural networks is used to achieve high pattern recognition accuracy, thereby demonstrating the suitability of the use of the device in a neuromorphic system. Finally, the device is used as a physical reservoir with time-dependent inputs to realize reservoir computing by using short-term memory properties. Our study reveals that the proposed device can be applied in artificial intelligence-based computing applications by utilizing its programmable retention properties.

Higher-Order Structural Analysis of a Transparent and Flexible High Thermal Conductive Liquid Crystalline Elastomer Sheet and Its Composite.

Transparency, flexibility, and high thermal conductivity are trade-offs. Specifically, we have investigated a cross-linked acrylic liquid crystal elastomer (LCE) that exhibits both transparency and flexibility while maintaining a high level of thermal conductivity. The transparent monodomain LCE sheet was achieved through a process of stretching an initially opaque polydomain sheet to 80% elongation and subsequently subjecting it to photocuring. The thermal conductivity in the stretching direction (x) of the monodomain LCE sheet was found to be 1.8 times higher than that of the prestretched polydomain sheet, consistent with findings from previous studies. However, in the orthogonal direction (y) to the stretching (x) direction, the thermal conductivity exhibited an even higher value, being 1.7 times greater than in the x-direction, with a value of 3.0 W/(m·K). This unique observation prompted us to conduct further investigation through higher-order structural analysis of these LCE sheets using 2D wide-angle X-ray scattering (WAXS) analysis. In the transparent sheet, the LCE molecules were aligned in the sheet in the stretching x-direction (monodomain structure) for the out-of-plane direction. However, in the in-plane x-direction, the molecular plane spacing exhibited random orientation at a period of 0.45 nm. In contrast, within the y-direction of the inner layer, the molecular plane spacing exhibited a uniaxial horizontal orientation at the same period length as in the x-direction. The heat energy entering into the y-direction once spreads to the x-direction, but it was considered that the reason for the higher thermal conductivity to the y-direction would be forming covalent bonds that function as new heat transmission paths, in the direction intersecting to the x-direction during photocuring. Therefore, we concluded that the synergistic effect of the high level of the ordered inner structure and covalent bonding structure due to cross-linking in the y-direction contributes to its higher thermal conductivity compared to that in the x-direction, which exhibits a random in-plane structure. Additionally, we have fabricated an LCE composite sheet filled with 75 vol % of alumina particles using a polydomain-type LCE as the base material. The composite sheet exhibits remarkable thermal conductivity in the thickness direction, measuring at 9.8 W/(m·K), while maintaining a flexibility characterized by an elastic modulus of 70 MPa. This thermal conductivity surpasses that of a nonmesogenic acrylic composite sheet with identical alumina particle filling, which measured at 3.9 W/(m·K), more than twice as much. The presence of the mesogen skeleton has been demonstrated to enhance heat transfer, even within soft composites, by facilitating the formation of an ordered structure.

A State of the Art on Cryogenic Cooling and Its Applications in the Machining of Difficult-to-Machine Alloys.

Cryogenic cooling has gathered significant attention in the manufacturing industry. There are inherent difficulties in machining materials that are difficult to machine because of high levels of hardness, abrasiveness, and heat conductivity. Increased tool wear, diminished surface finish, and reduced machining efficiency are the results of these problems, and traditional cooling solutions are insufficient to resolve them. The application of cryogenic cooling involves the use of extremely low temperatures, typically achieved by employing liquid nitrogen or other cryogenic fluids. This study reviews the current state of cryogenic cooling technology and its use in machining difficult-to-machine materials. In addition, this review encompasses a thorough examination of cryogenic cooling techniques, including their principles, mechanisms, and effects on machining performance. The recent literature was used to discuss difficult-to-machine materials and their machining properties. The role of cryogenic cooling in machining difficult materials was then discussed. Finally, the latest technologies and methods involved in cryogenic cooling condition were discussed in detail. The outcome demonstrated that the exploration of cryogenic cooling methods has gained prominence in the manufacturing industry due to their potential to address challenges associated with the machining of exotic alloys.

ZnO sintering additive without negative impact on proton-conducting SrHf0.8Sc0.2O3-δ electrolyte

Many proton-conducting oxides are refractory, making it difficult to fabricate dense electrolyte membranes for electrochemical devices. The use of a sintering additive is a common strategy, although it often has a negative effect on proton transport. We found that the addition of ZnO (2 and 4 mol%) successfully contributes to densification of SrHf0.8Sc0.2O3-δ ceramics at 1450 °C without negative consequences for the ionic transport. The chemical stability of the materials, high levels of hydration and proton conductivity were confirmed. ZnO is partially (less than 0.3 mol%) incorporated into the crystal lattice of the perovskite and partially accumulates at grain boundaries gradually volatilizing during high-temperature treatments. As a result, ZnO sintering additive does not influence the bulk and specific grain-boundary conductivities, ionic transference numbers and hydration ability, maintaining the excellent electrolytic properties of SrHf0.8Sc0.2O3-δ ceramics.

Modelling effluent reuse in the pulp and paper industry to predict consequences on conductivity.

The objective of this study was to assess, through simulation, conductivity variations in pulp and paper circuits when recycling waste water treatment plant (WWTP) effluent with a view to reducing fresh water use in a tissue mill. WWTP effluent was recycled in the process for different uses. A PS2000 digital model coupled with the PHREEQC chemical simulation engine was used to identify and quantify the main sources of conductivity: caustic soda, sodium bisulphite and acetate production through anaerobic microbial activity. Recycling WWTP effluent enables fresh water uptake to be reduced by 50% when used for pulp dilution or white water, by 81% when used in paper machine showers, and up to 96% for all uses combined. As fresh water use decreases, circuit closure increases along with, consequently, COD and conductivity. COD build-up can be controlled by best available techniques application. Recycling WWTP effluent has a strong impact on conductivity. However, the impact of high conductivity levels on additives performance is limited in the case of the mill studied. Acetate concentration could be controlled by better agitation of tanks or the introduction of air by pumps. Furthermore, limiting acetate production can reduce the need for caustic soda to control the pH.

Phase evolution, defect chemistry, and electrical properties of Na0.5Bi0.5TiO3-BiNi0.5Ti0.5O3 solid solutions

Solid solutions of Na0.5Bi0.5TiO3 (NBT) and BiNi0.5Ti0.5O3 (BNiT) were prepared by a solid-state reaction route, and their electrical properties investigated by a combination of impedance spectroscopy and electromotive force measurements to explore the possibility of developing mixed ionic-electronic conductors based on NBT. Phase analysis showed that BNiT has a large solid solution limit in NBT (60 mol% based on X-ray diffraction), and the room temperature crystal structure changes from rhombohedral to pseudo-cubic with increasing BNiT content. Neutron diffraction revealed the coexistence of rhombohedral and tetragonal phases when the BNiT content ≥ 40 mol%. Electrically, incorporation of BNiT induces p-type electronic conduction into NBT by hopping of holes between Ni2+ (NiNix) and Ni3+ (NiNi·), and therefore changes the electrical conduction mechanism systematically from predominant oxide-ion conduction to mixed ionic-electronic conduction and then to predominant p-type electronic conduction. The total conductivity of the solid solutions showed a “V-shape” variation with increasing BNiT content. Possible mechanisms for the phase evolution and the conductivity-composition relationships are discussed. Achieving high levels of ionic and electronic conductivity simultaneously in NBT by introducing elements with variable oxidation states remains challenging due to the competition between an enhanced electronic component and a suppressed ionic component. Low levels of BNiT incorporation are, however, beneficial to reducing the dielectric loss of NBT for dielectric applications.

Groundwater quality and hydrochemical characteristics in the upper Seybouse sub-basin, Northeast Algeria.

The present study aims to evaluate the groundwater quality in an area characterized by significant human anthropic activities within the upper Seybouse. In order to assess the quality, a total of 20 samples were analyzed to identify the chemical and bacteriological composition of the water, its variations, and their potential impacts on the environment and human health. The results revealed concentrations of the chemical and bacteriological elements exceeding the WHO standards, with high levels of electrical conductivity (EC) (peak = 4210 μS/cm), Ca2+ (peak = 340.68mg/L), Na+ (peak = 360mg/L), HCO3- (peak = 287mg/L), Cl- (peak = 542mg/L), SO42- (peak = 687mg/L), NO3- (pek = 65.91mg/L), fecal coliforms (FC) (peak = 160 UFC/mL), fecal Streptococcus (FS) (peak = 43 UFC/mL), and Clostridium perfringens (CP) (peak = 29 UFC/mL). Within the basin, two different facies have been identified: Cl-SO4-Na type and Cl-SO4-Ca type. The calculated Water Quality Index (WQI) indicates that none of the groundwater samples are suitable for drinking or human consumption. The detection of pathogenic microorganisms through diverse molecular methods has revealed the existence of eight distinct species, encompassing pathogenic strains that can affect human health. Moreover, the dissolution of geologic formations can influence the water's chemistry. In this region, groundwater pollution seems to be influenced by anthropogenic and agricultural factors such as fertilizer application, irrigation practices, and the release of domestic sewage.

Instream barriers contribute to population isolation of a small‐bodied, benthic, headwater‐specialist fish (Percidae)

AbstractGenetic differentiation in aquatic systems is often driven by geographic distance (isolation by distance) due to the linear and hierarchical distribution of populations, but habitat fragmentation often exacerbates this effect by decreasing population connectivity, leading to isolation by resistance. Stronghold populations of the Kentucky Arrow Darter (Etheostoma spilotum) in the South Fork Kentucky River system within the Daniel Boone National Forest of eastern Kentucky, USA have a high population structure not explained by distance alone. Higher than expected levels of genetic differentiation among proximate populations were hypothesized to be driven by land‐use change, but this was not previously tested. Here we use a riverscape genetics approach to test for the effects of natural landscape features including slope, elevation and stream size, and anthropogenically altered habitat features, including specific conductance (conductivity), culverts and forest cover, on population connectivity and genetic diversity of E. spilotum. We found isolation of populations among all tributary systems and a strong, positive relationship between genetic and geographic distances as expected. However, high conductivity levels due to surface coal mining best explain the population structure observed. We also found signatures of low genetic diversity overall and indicators that culverts may limit upstream movements of E. spilotum. This study provides a novel fine‐scale view of the effects of instream and landscape features on connectivity among, and genetic diversity within populations of an imperilled, small‐bodied, benthic fish.