High Irradiance Conditions Research Articles

Biomass Productivity and Photosynthetic Activity in Ulva compressa (Chlorophyta) in Raceway Photobioreactors Under Stress Conditions.

Research in seaweed cultivation technologies aims to increase production and reduce costs, leading to more efficient and sustainable processes. In this study, we analyzed the outdoor production of Ulva compressa cultured in summertime at different stocking densities of 0.6, 0.8 and 1.0 kg Fresh weight (FW) m-2 in a raceway photobioreactor with 30 m2 surface (3000 L), and its relation to photosynthetic activity. Under the experimental conditions of high temperature (>28-30 °C) and pH > 9 in culture water, higher seaweed density resulted in lower specific growth rate. The biomass production has been related to photosynthetic activity by using in vivo chlorophyll a fluorescence. Dynamic photoinhibition was observed at noon, which was less severe in cultures with higher algal densities. However, photosynthesis recovered in the afternoon. Seaweeds that were acclimatized for a week to the conditions of 1.0 kg FW m-2 stocking density showed an increase in biomass growth and absence of photoinhibition compared to non-acclimatized thalli. In conclusion, the cultivation of U. compressa in a mid-scale raceway photobiorreactor under conditions of high irradiance and temperature and low nutrient input, exhibited the best photosynthetic performance and hence the highest growth rates for the highest culture density assayed (1.0 kg FW m-2).

An ultrastable luminescent covalent organic polymer for selective Pd2+ detection in strong acid

AbstractThe low natural abundance of palladium (10 ppb) in the Earth's crust highlights its considerable potential as a valuable resource, especially given that spent nuclear fuel contains approximately 1–2 kg of Pd per ton. However, the detection and separation of Pd2+ from high‐level liquid waste (HLLW) present significant challenges due to high acidity (2–5 M HNO3) and intense radiation conditions inherent in spent fuel reprocessing. We present a cyano‐olefin‐linked covalent organic polymer (COP‐TnPp) that exhibits remarkable stability in strong acidic environments and resilience to radiation. Thanks to its olefin linkage, which facilitates π‐electron conjugation, COP‐TnPp exhibits strong luminescence, whose intensity remains stable across a range of 1–5 M nitric acid solutions. Pd2+ ions can effectively quench the fluorescence of COP‐TnPp in 1 and 5 M HNO3 solutions with detection limits of 0.37 and 0.63 μM, respectively. Additionally, COP‐TnPp demonstrates exceptional selectivity for Pd2+ ions, even amidst 22 other interfering ions in a simulated HLLW solution (5 M HNO3), with the detection limit remaining at 0.697 μM. This work not only marks an advancement in the development of materials for detecting Pd2+ in extreme acidic conditions but also offers new insights into the detection of other radionuclides under similarly challenging environments.

Characterization of an Environmentally Responsive Organic-Inorganic Hybrid Fe3O4/SiO2/PPy-c Core-Shell Nanocomposite with Magneto-Chromatic Ability for Synergistic Electrical Properties.

The aim of this study was to analyze the properties of a composite that incorporates carbon black and polypyrrole within an Fe3O4/SiO2 core-shell structure, synthesized using the Stöber method under high ultrasonic irradiation conditions (120 W) for Fe3O4/SiO2 nanocomposite. The Fe3O4/SiO2 core-shell indicates magnetochromatic behavior characterized by temperature-dependent coloration and magnetic alignment. Incorporating carbon black and polypyrrole at moderate temperature (5-15 °C) enhanced the electrical conductivity. The electrical resistivity ρ was 7.30 × 106 Ω·cm for Fe3O4, 3.19 × 108 Ω·cm for Fe3O4/SiO2, and 242.56 Ω·cm for Fe3O4/SiO2/PPy-c at room temperature. When it was performed at moderate temperature (5-15 °C), the ρ of the prepared Fe3O4/SiO2 and Fe3O4/SiO2/PPy-c nanocomposite was 1.08 × 108 and 0.00799 Ω·cm, respectively. Current-voltage measurements revealed a linear relationship, with butterfly shaped curves in the forward-bias region for all samples. The Fe3O4/SiO2/PPy-c nanocomposite's tunable synergistic electrical properties at moderate temperatures make it useful for environmental applications, electrical wiring, and circuitry.

Plant growth and physiological responses of the invasive plant Acmella radicans to contrasting light and soil water conditions

Acmella radicans (Jacquin) R.K. Jansen is a new invasive species record for Yunnan Province, China, as of 2017 and little is known about its invasion mechanisms. To better understand its invasive strategies, we investigated the growth, physiological and soil nutrient use parameters of the invader under combined conditions of light (25%, 50%, 75%, and 100% of light availability) and soil water content (full, high, medium, and low soil water content) in the glasshouse. The results showed that light level, soil water content and their interaction had a significant effect on all plant morphological, physiological and soil nutrient parameters for A. radicans (P < 0.05). For the most part, plant height, total branch length, leafstalk length, leaf area, inflorescence number, seed number, leaf biomass, stem biomass, aboveground biomass, and total biomass of A. radicans were significantly increased with increased shading rate and soil water content and were generally greater at intermediate light levels and intermediate to high soil water levels. Under high-irradiance conditions, the chlorophyll content was greatly reduced compared to other treatments. We also observed that leafstalk length, leaf area, Pn, chlorophyll a, and chlorophyll b of A. radicans were markedly increased with increased shading rate and soil water content, and were generally highest under intermediate irradiance and soil water conditions, but many plant physiological parameters also exhibited relatively high values under waterlogging conditions. The concentrations of organic matter, available N and available K of A. radicans soils at high-irradiance and full-high soil water content treatments and medium-irradiance and high-medium soil water content treatments were often less than those of other treatments indicated that hypothetically soil absorption was increased by moderate shading and high soil water. This was the first study demonstrating that A. radicans thrives best under moderate light conditions in combination with high soil water. Furthermore, we surmised that its higher phenotypic and physiological plasticity contributes to its invasion success.

Enhanced Marangoni flow to fabricate uniform and porous SiO2 films: Toward superior high transparency, antifogging, and self- cleaning properties

Fogging on transparent substrate greatly impacts transmittance, causing inconvenience and potential hazards. Increasing surface roughness to enhance hydrophilicity often reduces transmittance. Here, by enhancing the Marangoni flow to inhibit the coffee-ring effect during SiO2 droplet drying, we propose for the first time to manufacture superhydrophilic and high-transmittance coatings with porous structures on various substrates, including glass and resin. This approach relies on a simple, potentially large-scale ultrasonic spray method to enhance the Marangoni flow of SiO2 dispersion with different particle sizes by adding multiple surfactants to reduce the surface tension of the dispersion. The water contact angle of the SiO2 film decreases to below 5° within 0.5 s, imparting anti-fogging properties to the substrate. The film exhibits a transmittance of 93.1 % at 580 nm, surpassing the inherent 90.8 % transmittance of the bare glass. Notably, the film shows remarkable self-cleaning properties due to potent hydration from eco-friendly SiO2 nanoparticles and the porous structure. Owing to the hydrogen bonding between tightly packed small-sized SiO2 particles as well as between the particles and substrate, the surface morphology of the film on glass remains intact even after washing, and soaking. The porous SiO2 film, with a contact angle dropping to below 5° within 0.5 s, maintains its superhydrophilicity even after being exposed to high temperatures, UV irradiation, and humidity conditions. The simple production process of the porous SiO2 films offers a promising method for preparing high-transmittance anti-fogging films with significant industrial potential.

Study of time resolution measurements and prospects for energy resolution of an ultra-compact sampling calorimeter (RADiCAL) module at EM shower maximum over the energy range 25 GeV 150 GeV

The RADiCAL Collaboration is conducting R&D on high performance electromagnetic (EM) calorimetry to address the challenges expected in future collider experiments under conditions of high luminosity and/or high irradiation (FCC-ee, FCC-hh, fixed target and forward physics environments). Under development is a sampling calorimeter approach, known as RADiCAL modules, based on scintillation, wavelength-shifting (WLS) technologies and photosensor, including SiPM or SiPM-like technology. The modules discussed herein consist of alternating layers of very dense tungsten (W) absorber and scintillating crystal Lutetium Yttrium Orthosilicate LYSO(Ce) plates, assembled to a depth of 25 X0. The scintillation signals produced by the EM showers in the region of EM shower maximum (shower max) are transmitted to SiPM located at the upstream/downstream ends of the modules via quartz capillaries which penetrate the full length of the module. The capillaries contain DSB1 organic plastic WLS filaments positioned within the region of shower max, where the shower energy deposition is greatest, then fused with quartz rod elsewhere. The wavelength shifted light from this spatially-localized shower max region is then propagated to the photosensors. This paper presents the results of an initial measurement of the time resolution of a RADiCAL module over the energy range 25 GeV ≤ E ≤ 150 GeV using the H2 electron beam at CERN. The data indicate an energy dependence of the time resolution that follows the functional form: σt=a/E⊕b, where a = 256 GeV ps and b = 17.5 ps. The time resolution measured at the highest electron beam energy for which data was currently recorded (150 GeV) was found to be σt = 27 ps.

Photosynthetic distribution inside a cylindrical photobioreactor for Botryococcus braunii: A fed-batch culture application

In this study, the physiological responses and kinetic parameters of Botryococcus braunii were analyzed during a highly irradiated fed-batch culture in a cylindrical photobioreactor. This work includes a model of photon distribution throughout the bioreactor, coupled with an analysis of photosynthetic performance to simulate the level of photosaturation, photolimitation, or photoinhibition during cell growth culture. Under this simulation, the kinetic and physiological behavior was evaluated during four cycles of fed-batch culture. Physiological responses showed cellular photoacclimation to high irradiance conditions, increasing the Electron Transport Rate (ETR) values 2.5 times from cycle 1 to cycle 4, while photoprotection mechanisms such as quantum yield YII and non-photochemical quenching NPQ remained efficient. The total pigment content was low compared to other studies, and a gradual decrease in Chl a, Chl b, and carotenoids was evident between each fed-batch cycle (a 25 % reduction from cycle 1 to cycle 4). Kinetics showed a gradual increase in productivity, growth rates, and nutrient consumption between cycles. The maximum biomass concentration as dry weight (4.86 ± 0.26gL−1) was obtained in cycle 4, which also showed the highest values of productivity (0.45gL−1d−1), specific growth rate (0.134 d−1) and consumption rate (NO3, PO4). The results correlate the engineering approach to the physiological characteristics of the species, indicating that it is possible to establish an efficient fed-batch system for microalgae production.

A novel strategy for iodine removal from nuclear reactor accidental gases: efficient adsorption of CH3I on the moderately hydrophobic modified silver-loaded zeolite under high temperature and humidity conditions

ABSTRACT Ensuring nuclear energy safety through effective gas emission filtration from nuclear reactor containment in accident scenarios is paramount. The efficacy of hydrophobic modified Ag-loaded zeolites for methyl iodide (CH3I) removal under challenging conditions of high temperature, humidity, and irradiation is studied in this work. Through hydrophobic modification of AgX zeolite with three different silane coupling agents, a series of modified zeolites with varied hydrophobicity levels is produced. The adsorption capabilities of these modified materials are assessed using a self-designed gas adsorption setup, focusing on CH3I removal from a gas mixture emblematic of nuclear accident environments. Results indicate that all hydrophobically modified zeolites exhibited superior CH3I removal rates compared to their unmodified counterparts, with the variant modified with 10% phenyltriethoxysilane achieving the highest removal rate of 99%. Additionally, zeolites modified with octyltrimethoxysilane demonstrate commendable irradiation resistance at a radiation dose of 4.2 × 105 Gy. The results suggest that optimally hydrophobically modified AgX zeolites hold significant promise for filtering gases containing radioactive iodine, offering novel insights for the advancement of adsorbent materials in nuclear reactor containment discharge systems.

A Hierarchical Priority Based Multi-Bit Error Tolerant Design for FPGA Configuration Memory

The reconfigurability of a field-programmable gate array (FPGA), which is utilized in many applications, permits changes to be made to an existing design. In hostile environments such as space, where radiation and ionizing particles increase the risk for failure and human maintenance is either impossible or time-consuming, this reconfigurable capability becomes even more important. Single event upsets (SEUs) and multi-bit upsets (MBUs) on configuration memory can cause soft errors and circuit malfunctions in SRAM-based field programmable gate arrays (FPGAs). The ever-increasing quantity of configuration bits in contemporary FPGAs makes it more difficult for traditional scrubbing to identify faults in a timely manner, leading to a mismatch between scrubbing performance and MBU sensitivity.A hierarchical multi-bit error correcting method fully utilizes the MBU sensitivity at various configuration frame locations. It employs distinct techniques for varying priorities and differentiates across configuration frames with multiple priorities. They divided code words into several sections and used distinct error-correction techniques in each section. In high radiation conditions, the suggested integrated error correction technique enhances FPGA configuration memory protection by substituting memory scrubbing. The suggested approach lowers total TTD and enables priority-based asynchronous MBU detection and correction. Index Terms—FPGA,MBU,Sensitivity,Configuration memory

Effect of proton irradiation dose rate and implanted hydrogen ions on spinodal decomposition in thermally aged EQ308L stainless steel weld metal

Abstract Stainless steel welds with a ferritic phase are extensively utilized in nuclear power plants. Spinodal decomposition stands as the primary factor contributing to the degradation of their service performance. Ion irradiation has been widely employed to investigate the damage behavior of materials. However, varying irradiation parameters, such as dose rate and implanted ions, are believed to result in significant differences in the extent of spinodal decomposition. In this paper, proton irradiation experiments were conducted at different dose rates on thermally aged EQ308L stainless steel welds. Spinodal decomposition within the ferrite at various radiation depths was compared and analyzed by using atom probe tomography to unveil the effects of dose rate and implanted hydrogen ions. The results reveal that, under conditions of high dose rate irradiation, spinodal decomposition can be partially alleviated when compared to the initial thermally aged state. Conversely, under low dose rate irradiation conditions, spinodal decomposition exhibits an enhancement trend. This difference may be attributed to the interplay between irradiation-enhanced diffusion and atomic mixing. Therefore, the dose rate significantly influences the progression of spinodal decomposition. Furthermore, implanted hydrogen ions may also inhibit spinodal decomposition within the ferrite, potentially by promoting the recombination of irradiation defects.

Improved 30‐m Evapotranspiration Estimates Over 145 Eddy Covariance Sites in the Contiguous United States: The Role of ECOSTRESS, Harmonized Landsat Sentinel‐2 Imagery, Climate Reanalysis, and Deep Neural Network Postprocessing

AbstractThis study developed and evaluated 30‐m daily evapotranspiration (ET) estimates using the Priestley‐Taylor Jet Propulsion Laboratory (PT‐JPL) model with ECOSTRESS, Moderate MODIS, harmonized Landsat Sentinel‐2 (HLS) imagery, ERA5‐Land reanalysis, and eddy covariance measurements. The new daily 30‐m ET showed significantly improved performance (overall, r = 0.8, RMSE = 1.736, KGE = 0.466) at 145 EC sites over contiguous United States compared to the current 70‐m ECOSTRESS ET (overall, r = 0.485, RMSE = 4.696, KGE = −0.841). A deep neural network postprocessing model trained with ET measurements from EC sites further improved the performance on test sites that were not used for model training (overall, r = 0.842, RMSE = 0.88, KGE = 0.792). The 30‐m ET estimation biases were significantly related to the biases in the upwelling longwave (RUL) and downwelling shortwave radiation (RDS) inputs, with ET estimates driven by MODIS radiation showing higher biases compared to those driven by ERA5‐Land radiation. The error diagnosis using random forest indicates that ET biases tend to be larger under higher ET estimates, and RUL and RDS were the primary contributors to the high bias at the higher ET ranges, with partial dependence plots revealing that the estimation biases tend to be higher under more humid environment, denser vegetation covers, and high net radiation conditions. In conclusion, higher spatial resolution satellite imagery of vegetation characteristics and higher temporal resolution radiation data, combined with continent‐wide EC measurements and deep learning, provided substantial added value for improving ET estimations at the field scale (30‐m).

High-rate tests on resistive plate chambers operated with eco-friendly gas mixtures

Results obtained by the RPC ECOgas@GIF++ Collaboration, using Resistive Plate Chambers operated with new, eco-friendly gas mixtures, based on tetrafluoropropene and carbon dioxide, are shown and discussed in this paper. Tests aimed to assess the performance of this kind of detectors in high-irradiation conditions, analogous to the ones foreseen for the coming years at the Large Hadron Collider experiments, were performed, and demonstrate a performance basically similar to the one obtained with the gas mixtures currently in use, based on tetrafluoroethane, which is being progressively phased out for its possible contribution to the greenhouse effect. Long term aging tests are also being carried out, with the goal to demonstrate the possibility of using these eco-friendly gas mixtures during the whole High Luminosity phase of the Large Hadron Collider.

Highly luminescent CsPbX3@MIL-53(Al) nanoarchitectonics with anomalous stability towards flexible emitting films

The poor stability of perovskite nanomaterials exposed in high temperature, moisture, light radiation, and polar solvent conditions severely restrict their commercial application. To address this issue, the growth in situ of CsPbX3 (X = Cl, Br, I) nanocrystals (NCs) is carried out by using the stable aluminum (Al)-based metal-organic frameworks to create CsPbX3@MIL-53(Al) composites. Compared with pristine CsPbX3 NCs prepared using room temperature ligand assisted re-precipitation synthesis, the CsPbX3@MIL-53(Al) composites exhibit narrow photoluminescence (PL) spectra and greatly improved stability. The green emitting CsPbBr3@MIL-53(Al) composite exhibit narrowed PL spectrum (the full width at half-maximum of PL spectra: 20 nm for the composite and 28 nm for CsPbBr3 NCs) and a blue-shifted PL peak wavelength (517.6 nm for the composite and 527.6 nm for the CsPbBr3 NCs). The relationship of microstructure, components, PL, fluorescence lifetime, and stability are discussed systematically. Anomalous stability against heat-treatment, polar solvent and humidity conditions indicated the composites retained their initial PL intensity after storge more than 4 months in ambient conditions and heat-treated to 120ºC for 5 cycles. The emitting color of CsPbBr3@MIL-53(Al) composites are easily adjusted from blue, green to red by controlling the halide components of precursors. The composite was used to create emitting coating and highly bright flexible emitting films which also reveal high stability, suggesting that in situ encapsulation of CsPbX3 NCs in MIL-53(Al) would supply a novel platform for various emitting devices.

Passive Electroluminescence and Photoluminescence Imaging Acquisition of Photovoltaic Modules.

In photovoltaic power plant inspections, techniques for module assessment play a crucial role as they enhance fault detection and module characterization. One valuable technique is luminescence. The present paper introduces a novel technique termed passive luminescence. It enhances both electroluminescence and photoluminescence imaging acquisition in photovoltaic power plants under normal operation in high irradiance conditions. This technique is based on the development of an electronic board, which allows the polarity of the module to be changed, enabling the current generated by the photovoltaic string to be injected into the module and producing electroluminescence effects. Additionally, the board can bypass the module and set an open circuit, inducing photoluminescence emission using sunlight as an excitation source. The proper coordination of the board and an InGaAs camera with a bandpass filter has allowed for the integration of a lock-in technique, which has produced electroluminescence and photoluminescence pictures that can be used for fault detection.

Preliminary study of a small high-temperature gas-cooled reactor (HTGR) concept with MgO–BeO moderators

Graphite plays a crucial role as a moderator and reflector in high-temperature gas-cooled reactors (HTGRs). However, under high-irradiation conditions, graphite exhibits microcracking within the operational period. Studies have been investigated the potential of composite-based materials for replacing graphite in HTGRs. This study focused on a magnesium oxide (MgO)-based composite material as the host matrix and a homogeneously distributed beryllium oxide (BeO) as the entrained moderating phase and investigated the feasibility of the MgO–BeO as the new moderator in a small HTGR to achieve high burnup performance. In this study, the conceptual design of the HTR50S was selected as one of the candidates for the small HTGR concept. Burnup calculations and safety evaluation in HTR50S design were performed. The Monte Carlo MVP 3.0 and MVP-BURN codes were used in this study for neutronic calculations. Results revealed that a high burnup of 80 GWd/t can be achieved using a fuel composition of 6 kg heavy metal per fuel block with 17 wt% of 235U enrichment. Furthermore, a negative temperature coefficient of reactivity was achieved during the operation period.

Multi-pixel photon counter-based gamma camera with pinhole collimator to locate Cs-137 sources at high dose rates for the Fukushima nuclear power plant

The Fukushima Daiichi Nuclear Power Plant was severely damaged during the 2011 Great East Japan Earthquake. However, the ongoing decommissioning work has been limited by the complexity of the reactor's internal structure and very high radiation levels; locating radioactive sources is essential for efficient decommissioning. Conventional gamma cameras are mainly designed for low radiation dose (∼mSv/h) and using them under high radiation conditions is difficult (>Sv/h). Therefore, we developed a pinhole gamma camera with a gamma radiation detector consisting of a high-speed YGAG scintillator array and multi-pixel photon counters to locate radioactive sources at high dose rates. The gamma-ray photon signals captured by the developed two-dimensional detector array can be processed at a speed as high as >1 MHz/pixel using the developed large scale integrated circuit. Herein, we report the measurement results of an extremely high radioactivity of 137Cs (∼34 TBq) using the developed gamma camera. The gamma-ray source position was determined using an angular size of ∼4.6°, with images obtained at 2 m from the radioactive source and at a dose rate of 0.3 Sv/h. The direct gamma rays with a photoelectric peak at 662 keV and scattered component of gamma rays can be distinguished from the measured spectrum. We also characterize the imaging capability of the 137Cs depending on the detected gamma-ray energies and discuss related details.

Experimental comparison of a DC PV cooker and a parabolic dish solar cooker under variable solar radiation conditions

Solar cookersare not all-weather cooking devices and operate poorly during cloudy and low sunshine conditions. Their performance is evaluated usually during high solar radiation conditions. The objective of this study is to compare two solar cookers under variable non-ideal weather conditions. The comparison is carried out under variable solar radiation conditions to compare the all-weather performance of these two cookers. This is a major novelty compared to previous work reported where solar cookers are tested under high and ideal solar radiation conditions. Experiments to compare a PV DC battery-powered solar cooker and a parabolic dish solar cooker are presented in this paper. A total of six water heating tests are carried out to comprehensively compare these two types of solar cookers under different solar radiation conditions. Also, four food cooking tests are carried out with different types of food. The PV solar cooker shows almost constant input electrical power in the range of 160–180 W during the experimental tests whereas the input thermal power for the parabolic dish is highly variable depending on the solar radiation conditions (200–1200 W). The output water heating powers obtained using the PV cooker (66–100 W) are comparable to those obtained with parabolic dish solar cookers (78–142 W), regardless of the significantly lower input heating power. Water is boiled in all the heating tests with the PV cooker, whereas water is boiled for tests with low solar radiation variability for the parabolic dish solar cooker. Higher water heating efficiencies within a small range (0.38–0.57) are obtained for the PV cooker compared to the parabolic dish solar cooker (0.11–0.42). The water heating efficiency of the parabolic dish solar cooker is highly affected by ambient solar radiation and windspeed conditions. Food was well cooked with the PV cooker in all four food cooking tests, whereas food in only two tests with low solar radiation variability was well cooked for the parabolic dish solar cooker. The PV cooker proves to be an all-weather cooker from the experimental results obtained. Future work will extend the use of the PV system for other domestic applications such as lighting and refrigeration together with solar cooking for a multipurpose DC decentralized system for communities without grid connectivity.

Operating Experience of Snubbers in Indian Pressurized Heavy Water Reactors

In a Nuclear Power Plant (NPP), the piping layout needs to have flexibility to reduce the operating stresses and nozzle loads due to thermal expansion. At the same time, the piping and equipment need to be supported adequately to sustain the dynamic loads viz., seismic loads, sudden opening/closing of valves etc. In Indian Pressurized Heavy Water Reactors (PHWRs), Snubbers are provided on nuclear equipment & piping to serve both purposes i.e. allow flexibility for thermal movement during operation and at the same provide requisite rigidity to take care of dynamic loads. Snubbers are subjected to harsh environment during operation including high temperature, radiation, vibration and corrosive condition, which may adversely affect its performance. Various degradations viz., high drag force, shift in dynamic characteristics (locking characteristic), jamming etc. have been observed. Periodic testing of Snubbers is required to ensure the proper functioning during normal operating condition as well as during dynamic event. A dedicated In-Service Inspection (ISI) program for snubbers exists in Indian PHWRs to ensure healthiness/functionality of Snubbers. Efforts have been made to reduce numbers of Snubbers progressively in PHWR units. Numbers of snubbers have been significantly reduced in latest 700MWe PHWR Design. This paper covers the various degradations observed in snubbers, ISI program for snubbers, design modifications, Snubber testing, assessment for fitness for service, replacement of Snubbers in older units and optimization of snubbers.

The effect of diurnal warming of sea‐surface temperatures on the propagation speed of the Madden–Julian oscillation

AbstractThe diurnal warm layer in the upper ocean develops during low surface winds and high incoming solar radiation conditions, often increasing sea‐surface temperatures (SSTs) by up to 1°C. The suppressed phase of the Madden–Julian Oscillation (MJO) favours the formation of such a layer. Here, we analyse the coupled ocean–atmosphere and atmosphere‐only numerical weather prediction systems of the UK Met Office to reveal that important differences arise from the representation of the diurnal warm layer in the coupled model. Though both models are skilful in predicting the MJO to at least a 7‐day lead time, the coupled model predicts approximately 12% faster MJO RMM phase speed propagation than the atmosphere‐only model due to the ability to resolve diurnal warming in the upper ocean that rectifies onto MJO‐associated SST anomalies. The diurnal warming of SST (dSST) in the coupled model leads to an increase in daily mean SST compared with the atmosphere‐only model persisted foundation SST. The strength of the dSST in the coupled model is modulated by MJO conditions. During suppressed MJO conditions on lead day 1, the dSST is enhanced, leading to 0.2°C warmer daily mean MJO‐associated SST anomalies and increased convection in the coupled model by lead day 7. During active MJO convection, the dSST is suppressed, leading to 0.1°C colder MJO‐associated SST anomalies in the coupled model and reduced convection by lead day 7. This variability in dSST further amplifies the MJO propagation speed, underlining the importance of the two‐way feedback between the MJO and the diurnal cycle of SST and the need to accurately represent this process in coupled models.

Characterization of Cost-Saving Monofacial PERC Module under Field Conditions in South Korea

The photovoltaic (PV) industry is constantly striving to increase module power output while decreasing costs. Importantly, the performance and reliability of cost-saving products should be evaluated before being launched into the PV market to avoid any unnecessary side effects. This study investigated the performance of a monofacial module employing a cost-saving bifacial cell installed at a carport in South Korea. The bifacial cell reduces costs, compared to monofacial cell, by using a lower quantity of aluminum paste on its rear; consequently, it has become a popular product in the PV industry. The monofacial module employing the bifacial cell showed an improved voltage temperature coefficient and low-light performance over monofacial cell-based module. Our field data highlight three conclusions from the bifacial cell-based module; it showed (1) different voltage temperature coefficients with better performance at lower temperatures, (2) better low-light performance owing to high series resistance, and (3) high current owing to its bifaciality. Notably, under high irradiance and temperature conditions, the bifacial cell performed worse than the monofacial cell. We concluded that this type of cell may perform well under northern European climatic conditions, though further investigation is required to optimize cell performance under various weather conditions.