High Electromagnetic Interference Research Articles

Cellulose Nanofiber-Based Nanocomposite Films with Efficient Electromagnetic Interference Shielding and Fire-Resistant Performance.

Cellulose nanofiber (CNF) has been widely used as a flexible and lightweight polymer matrix for electromagnetic shielding and thermally conductive composite films because of its excellent mechanical strength, environmental performance, and low cost. However, the lack of flame retardancy seriously hinders its further application. Herein, renewable and biomass-sourced l-arginine (AR) was used to surface-modify ammonium polyphosphate (APP) and an environmentally friendly biobased flame retardant was synthesized by the coordination of zinc sulfate heptahydrate (ZnSO4·7H2O), which was named AAZ. AAZ was deposited on the surface of CNF by electrostatic adsorption and Zn2+ complexation. The biobased compatibilizer Triton X-100 was employed to assist the exfoliation of graphene nanoplatelets (GNPs) and their dispersion in the CNF matrix. Due to the formation of a dense lamellar layer resembling a shell structure, the CNF/GNPs composite films with a tensile strength of 52 MPa were obtained via vacuum-assisted filtration. Because the phosphorus-containing group produces a protective layer of PxOy compound and promotes the formation of a carbon layer by CNF and the combustion releases ammonia gas, the fire-resistant performance of the composite films was greatly improved. Compared with the pure CNF film, the composite film exhibits 33% reduction in PHRR value and 40% reduction in THR. In addition, the CNF/GNPs composite film with 20 wt % GNPs possessed high conductivity (2079.2 S/m) and electromagnetic interference (EMI) shielding effectiveness (37 dB). The ultrathin CNF/GNPs composite films have excellent potential for use as efficient flame retardant and EMI shielding materials.

Efficient adsorption of waste carbon nanotube by polyacrylamide gel to form wrinkled core-shell particles towards multifunctional composites for EMI shielding and sensing

Waste carbon nanotubes (CNTs) have always been a potential threat to the environment and biological health. However, the efficient recycling and utilization of CNTs has received little attention. Here, we used chemically cross-linked polyacrylamide (PAM) particles to adsorb waste CNTs in water to prepare PAM@CNT core-shell particles, which were blended with thermoplastic styrene-butadiene rubber (SBS) to prepare flexible composites. The concentration of residual CNTs in the supernatant was less than 3.5 μg mL−1, which meets the safety standards for discharge. The unique core-shell structure enables the composites with a thickness of 1 mm to exhibit high electromagnetic interference shielding effectiveness (53.3 dB) and low reflectivity (1.4 dB) at 30 wt% CNT content. In addition, at a CNT content of 10 wt%, the composites exhibit superior sensing properties concerning strain and solvents. Moreover, the composites prepared from different sources of waste CNTs have the same sensing properties. This work provides an effective strategy for the highly efficient recycling of waste CNTs for the preparation of green, high-performance multifunctional polymer composites for EMI shielding, human motion and solvent leakage monitoring, and solvent category differentiation.

Resonator-based near perfect metamaterial absorber with high EMI shielding for Wi-Fi and 5G applications

This paper introduces a perfect metamaterial absorber (MMA) achieving exceptional electromagnetic signal absorption at application-oriented frequencies of 2.40 and 3.50 GHz in addition to 6.09 GHz. The MMA exhibits absorption rates of 99.85, 98.6, and 96.7%, with high shielding effectiveness (SE) of 36.44, 32.58, and 31.13 dB against electromagnetic interference (EMI) at those frequencies. The structure of the copper resonator on the FR4 substrate allows the on-design frequency switching from 3.43 to 3.70 and 5.65 to 6.55 GHz, respectively. The structural symmetry enables polarization and incidence angle independence up to 60° for both transverse electric and magnetic modes. The perfect absorption of the MMA is shown by the near-zero polarization conversion ratio. There is an adjacent correlation between the measurement and simulation results. The proposed MMA emerges as an efficient EMI shield for Wi-Fi and 5G signals, offering perfect absorption and extensive polarization characteristics.

Malleable, printable, bondable, and highly conductive MXene/liquid metal plasticine with improved wettability

Integration of functional fillers into liquid metals (LM) induces rheology modification, enabling the free-form shaping of LM at the micrometer scale. However, integrating non-chemically modified low-dimensional materials with LM to form stable and uniform dispersions remain a great challenge. Herein, we propose a solvent-assisted dispersion (SAD) method that utilizes the fragmentation and reintegration of LM in volatile solvents to engulf and disperse fillers. This method successfully integrates MXene uniformly into LM, achieving better internal connectivity than the conventional dry powder mixing (DPM) method. Consequently, the MXene/LM (MLM) coating exhibits high electromagnetic interference (EMI) shielding performance (105 dB at 20 μm, which is 1.6 times that of coatings prepared by DPM). Moreover, the rheological characteristic of MLM render it malleable and facilitates direct printing and adaptation to diverse structures. This study offers a convenient method for assembling LM with low-dimensional materials, paving the way for the development of multifunctional soft devices.

Flexible multifunctional magnetic-conductive Janus nanocomposite films towards highly-efficient electromagnetic interference shielding and thermal management

The rapid development of aerospace, intelligent wearable electronics and 5G communications puts forward higher demands for electromagnetic interference (EMI) shielding materials. Herein, the flexible multifunctional magnetic-conductive Janus nanocomposite films with magnetic cobalt carbide nanowires/bacterial cellulose (Co@C NW/BC) blends as the upper side, and conductive Ti3C2Tx MXene as the bottom side are obtained via the layer-by-layer (LBL) vacuum assisted filtration-hot pressing method. The two magnetic and conductive sides endow the Janus nanocomposite films with distinctly different performances in EMI shielding and thermal management. When the electromagnetic waves are incident from Co@C NW/BC side, the films exhibit a high EMI shielding effectiveness (EMI SE) of 49.8 dB with an enhanced microwave absorption (SEA) of 33.9 dB at the ultralow thickness of 43 μm. Meanwhile, the Ti3C2Tx side exhibits improved electrical heating performances with a surface temperature of 120 °C at 6 V voltage, increased photothermal conversion temperature of 77.8 °C upon 2.0 kW/m2 light intensity, as well as excellent thermal stealth properties with a low radiation temperature of 88.4 °C on the 240 °C hot stage. Moreover, the Janus nanocomposite films show a high tensile strength of 80.0 MPa. The resultant Janus nanocomposite films possess great application prospects in highly-efficient EMI shielding and thermal management.

Absorption-dominant electromagnetic interference shielding material using MXene-coated polyvinylidene fluoride foam

MXene (Ti3C2Tx), known for its exceptional electrical conductivity, unique two-dimensional structure, extensive surface functionality, and hydrophilicity, has emerged as a leading candidate for electromagnetic interference (EMI) shielding applications. Despite these excellent characteristics, EMI shielding materials based on MXene mostly utilize the reflection mechanism, which may cause secondary interferences. This study introduces an approach to utilize MXene as absorption-dominant EMI shielding materials. By engineering a porous layer of polyvinylidene fluoride (PVDF) atop MXene nanoflakes, we achieved a synergistic enhancement in EMI shielding effectiveness (SE) and absorptivity. The PVDF foam serves as an effective impedance matching layer, substantially enhancing the absorption of electromagnetic waves into the shielding material. Incorporating electrically conductive MXene nanoflakes to form a thin film creates a robust conductive network, fully leveraging its inherent performance. This network efficiently dissipates EM waves, thereby significantly enhancing the EMI SE. The shielding performance of this composite was thoroughly evaluated across both the X-band (8.2 GHz–12.4 GHz) and the Ka-band (26.5 GHz–40 GHz) frequencies. It demonstrated high EMI SE, attributed to mechanisms predominantly based on absorption. Specifically, it achieved an EMI SE of approximately 63.3 dB with high absorptivity (0.74) in the X-band and approximately 73.3 dB with high absorptivity (0.85) in the Ka-band. These findings underscore its potential as a route to develop absorption-dominant EMI shielding materials.

Oxhide gelatin-regulated aramid nanofiber/liquid metal films with sandwiched structure for electromagnetic interference shielding

Liquid metal (LM) based electromagnetic interference (EMI) shielding materials with high conductivity and continuous deformation capacity are important needs for meeting modern advanced electronic equipment. However, an independent free-standing film with LM is difficult to achieve due to its unique fluidity properties. Here, a simple alternating filtration film-forming method was utilized to orderly construct a sandwiched EMI shielding film with LM stabilized by bio-based oxhide gelatin (gel) as the intermediate conductive layer, and two films of aramid nanofibers/oxhide gel (ANF/gel) as the external insulating protective layers. This design not only prevents LM from being exposed to environmental conditions, but also reduces the risk of chemical corrosion in practical applications. Under optimal LM addition conditions, the sandwiched film (0.3-3 L) exhibited better EMI shielding performance of 50.4 dB in the X-band than the blended film (0.7 dB), as well as excellent mechanical properties (tensile strength of 65.8 MPa, strain 8.6 %). More importantly, the sandwiched film still maintained reliable EMI shielding performance after being experienced largely physical deformation. This study provides a new solution for preparing LM-based EMI shielding composites, and is expected to arouse pursuit of high EMI shielding effects of bio-based gel while also paying attention to their safety.

Innovation in Methods for Incorporating Magnetite into Biocellulose for Electromagnetic Interference Shielding Effectiveness Applications

Materials with magnetic properties are essential in various electric sector technologies. However, the generation of pollutants is of concern, increasing the interest in developing new sustainable, low-cost magnetic materials. These materials have notable applications in protecting against electromagnetic interference (EMI), which can lead to health problems as well as environmental pollution. Therefore, the aims of the present study were to produce a sustainable magnetic polymer using different methods of magnetite incorporation, investigate its magnetic properties, and determine its EMI shielding potential. The magnetic BC materials were obtained via in situ and ex situ magnetic incorporation in processed BC membranes and BC hydrogels. Analyses were carried out using XRD, FTIR, SEM, and VSM, and tests were performed to assess electromagnetic interference shielding effectiveness (EMI SE). The results revealed that the magnetite incorporation method influences the final size of nanoparticles, the arrangement among BC fibers, and the magnetic properties. Materials produced from processed BC had a higher percentage of incorporated magnetite and greater magnetic saturation, whereas those containing nanoparticles with a larger diameter had a stronger coercive field. Although samples did not have high EMI SE, magnetite increased the wave reflection and absorption of the material. This biomaterial can drive important innovations in the energy sector, particularly in efficient and ecological electrical infrastructure.

Hexagonal boron nitride nanosheets/graphene nanoplatelets/cellulose nanofibers-based multifunctional thermal interface materials enabling electromagnetic interference shielding and electrical insulation

Thermal interface materials (TIMs) that block electromagnetic interference (EMI) and current leakage are essential for high-density, high-power devices and compact form factors of electronic and mobility platforms. However, their coupled thermal-electrical-electromagnetic characteristics involve mismatches in thermal conductivity, electrical insulation, and EMI shielding, limiting the multifunctionality. Herein, a sandwich-like structural design that rationally combines graphene nanoplatelets (GNPs), hexagonal boron nitride nanosheets (BNNSs) and cellulose nanofibers (CNFs) is presented toward multifunctional trilayer TIMs enabling high thermal conductivity, EMI shielding, electrical insulation, mechanical compatibility and flame retardancy. The top and bottom BNNSs serve as electrically insulating yet thermally conductive layers while the GNPs in the central layer mitigate EMI and the CNFs as a binder complete the mechanical properties for the lamella-like trilayers. The resulting TIM exhibits a high in-plane thermal conductivity (25.5 W/m·K), and the LED cooling system using the TIM demonstrates the capability of reducing the operating temperature. Furthermore, it shows a high-volume resistivity (4.12 × 1013 Ω cm) and EMI shielding effectiveness (29.0 dB) at X-band frequencies. Its mechanical robustness is confirmed with tensile strength and elongation of 65.0 MPa and 2.36 %, and the high flame retardancy is validated. The outcomes will inspire tailoring multifunctional TIMs using lamellar structures that optimally combine micro/nanomaterials.

Flexible conductive polymer composite film with sandwich-like structure for ultra-efficient and high-stability electromagnetic interference shielding

Flexible electromagnetic interference (EMI) shielding films with the merits of light-weight, flexibility, and high EMI shielding performance are the essential materials for the consumer electronics and communication products. Herein, we construct a hybrid conductive network based on the electrospinning thermoplastic polyurethane (TPU) film loaded with different dimensional conductive fillers, including 0D FeCl3, 1D carbon nanotube (CNT) and 2D graphene nanosheet (GN) to achieve a flexible, light-weight, and ultra-efficient EMI shielding composite film. In specific, the electrospinning porous TPU film is firstly anchored by CNTs assisted by ultrasound to generate the porous TPU/CNT film. Thereafter, the as-prepared porous TPU/CNT film is loaded a GN/CNT/FeCl3 layer by vacuum-assisted filtration to generate a double-layer GN/CNT/FeCl3@TPU/CNT film. Finally, another porous TPU/CNT film is sealed onto the GN/CNT/FeCl3@TPU/CNT film by hot-pressing, which fabricates a sandwiched TPU/CNT@GN/CNT/FeCl3@TPU/CNT composite film. It is interesting to note that the composite film possesses the ultrahigh EMI shielding value (56.0 dB at 10.0 GHz) in the X-band (8.2–12.4 GHz) with high flexibility, excellent mechanical properties, long-term durability (acid-base environment resistance and stability after 1000 bends), as well as high thermal conductivity (6.53 W/(m.K)). This work proposes a simple but efficiency strategy to design the flexible EMI shielding film with ultra-high performance and outstanding durability.

Millefeuille-inspired biomass alternate multilayer composite, for excellent absorption-dominated, broadband EMI shielding and joule heating

The development of biomass electromagnetic interference (EMI) shielding materials with low cost, low reflection(R-value), and high shielding efficiency is promising but also challenging. Inspired by the alternate structure of a millefeuille, we propose an alternating assembly approach for conductive and magnetic layers. Employing sustainable bamboo fibers (BF) and biodegradable polylactic acid (PLA) as raw matrix, the magnetic and conductive layers were fabricated by compositing copper-plated BF (Cu@BF) and iron-plated BF (Fe@BF) with PLA, respectively. By alternately stacking magnetic and conductive layers and followed by hot pressing, the high EMI SE and low R-value biomass multilayer composite with “multi-(absorption-reflection-reabsorption)” structures were obtained. The performance of different alternating layers (3/5/7/9 layers) was studied, and a linear correlation between layer number, SE, and R-value was established. The results demonstrate that increasing the alternate layer number could readily tune the SE in the X-band from 45.02 dB (3-layer) to 80.2 dB (9-layer) and reduce Rmin from 0.40 to 0.25. Furthermore, the 9-layer composite exhibits approximately 75 dB SE in 1–18 GHz, simultaneously realizing high efficiency, low reflectivity, and broadband shielding. Notably, its excellent conductivity also provides reliable Joule heating performance. The shielding and thermal features of the composite highlight its potential in construction and smart housing heating applications.

Novel application of two- and four-lobed noise-canceling passive integrated transponder antennas for tracking fish in areas of high ambient electromagnetic interference.

Passive integrated transponder (PIT) technology is a leading tool for tracking fish in freshwater systems. PIT is highly applicable for assessing fish passage at anthropogenic infrastructure (e.g., dams and floodgates); however, there are often complications in operating PIT antennas near these structures due to the ambient electromagnetic interference of metal and power-supply equipment. We designed a PIT antenna that is resistant to the effects of ambient electromagnetic interference (AEMI). This design uses lobes with balanced polarity within the antenna to neutralize AEMI within the vicinity of the antenna. This novel PIT antenna provides a more effective and cost-efficient option for researchers tracking fish in environments with high AEMI.

Multifunctional wood-derived cellulose/Ti3C2Tx composite films enhanced by densification strategy for electromagnetic shielding, Joule/solar heating, and thermal camouflage

In the era of increasing reliance on electronic devices, the development of flexible smart composite films that offer multifunctional capabilities such as electromagnetic shielding, sensing, infrared stealth, and autonomous heating is becoming increasingly significant. In this study, we fabricated polydopamine-modified cellulose scaffold/MXene composite films (PCM) using a densification strategy, resulting in films with a thickness of only 33 μm, outstanding tensile strength of 235.28 MPa, and excellent electromagnetic shielding effectiveness of 44.6 dB. The PCM also demonstrates remarkable electrothermal performance, reaching temperatures of up to 610 °C at 5 V, and exhibits excellent photo-thermal conversion performance, along with good cycling stability and tunability. Additionally, the PCM’s low infrared emissivity provides it with exceptional infrared stealth capabilities, effectively concealing a high surface temperature ranging from 250 °C to 25 °C. The PCM’s ability to detect human body movement and light-driven actuation for bionic motions underscores its flexibility and utility as a sensor. Therefore, this efficient and versatile approach provides a promising method for synthesizing multifunctional MXene-based composite films, achieving satisfactory mechanical properties, high electromagnetic interference shielding, and effective thermal management for wearable smart devices and military applications.

Multifunctional polyimide/boron nitride nanosheet/Ti3C2Tx MXene composite film with three-dimensional conductive network for integrated thermal conductive, electromagnetic interference shielding, and Joule heating performances

With the demand for further miniaturization and higher frequency operation of electronic devices, polymer films with high thermal conductivity and electromagnetic interference (EMI) shielding effectiveness (SE) are urgently required. Herein, polyimide (PI)/boron nitride nanosheets (BNNS) aerogels with oriented porous structure are fabricated by unidirectional-freezing and freeze-drying methods. Subsequently, hierarchical PI/BNNS/Ti3C2Tx composite films with consecutively electrically and thermally conductive networks are successfully prepared via a unidirectional PI/BNNS aerogels-assisted immersion and hot-pressing strategy. Owing to the three-dimensional conductive dual networks of BNNS and Ti3C2Tx, the composite film exhibits excellent thermal conductivity with the maximum in-plane value of 4.73 W/(m·K), increased by 456 % compared to pure PI film. Moreover, the conductive network of Ti3C2Tx is conducive to the excellent EMI shielding performance, endowing the PI/BNNS/Ti3C2Tx composite film with an outstanding EMI SE value of 49.2 dB at 8.2 GHz with a low MXene content of 6 wt% and thickness of 300 μm. Furthermore, the composite film shows the superior Joule heating performance with fast thermal response and sufficient reliability. Therefore, the resulting composite film exhibits excellent thermal conductive, EMI shielding and Joule heating performance, which enables the potential application of multifunctional composites for thermal management and EMI shielding.

Large-area (50 cm × 50 cm) optically transparent electromagnetic interference (EMI) shielding of ZTO/Ag/ZTO: an analytical/numerical and experimental study of optoelectrical and EMI shielding properties

Transparent conducting oxides (TCOs), exhibiting both high optical transparency and low electrical resistivity, are commonly employed in optoelectronic devices. However, acquiring a balance between these optical and electrical properties in a uniform way over large areas has been a pending challenge, which is essential to achieving optically transparent electromagnetic interference (EMI) shielding surfaces. In this study, we propose and demonstrate a stratified thin film structure consisting of zinc-doped tin oxide (Zn2SnO4, ZTO) as TCO along with a metal layer of silver (Ag) deposited on a large area of 50 cm × 50 cm polycarbonate (PC) substrate enabled by a scanning magnetron sputtering gun. We achieved high EMI shielding of 99.9% at the optical transparency of 68% in the visible spectrum by engineering the stratified architecture of ZTO/Ag/ZTO. The Ag layer of 18 nm in thickness with a sheet resistance of 10 Ω/sq yields shielding effectiveness (SE) of 27 dB in a wide frequency range of 2–20 GHz. The bottom and top ZTO layers, 20 and 40 nm thick, respectively, provide the lowest optical loss of 13% across 400–700 nm. The structure’s EMI shielding, optical and structural performances were systematically characterized through a free-space focused-beam system, UV–Vis spectrophotometer, ellipsometry, focused ion-beam cross-sectional sampling and imaging, transmission electron microscopy, atomic force microscopy and secondary ion mass spectroscopy. EMI shielding and optical performances were validated by CST Microwave Studio and the transfer matrix method, respectively. These findings indicate that the proposed multi-layer architecture holds great promise for large-area EMI shielding and other optoelectronic applications.

Strong and flexible MXene-based nanocomposite films for atomic oxygen resistance and electromagnetic interference shielding

MXene has garnered considerable attention as a promising candidate for multifunctional artificial materials, owing to its exceptional mechanical performance and superior electric conductivity. However, macroscopically layered films assembled by MXene nanosheets are usually accompanied by serious degradation of mechanical properties. Moreover, there is a notable paucity of investigations on MXene in low Earth orbit (LEO) environment. Inspired by the layered structure of nacre, we applied polyurethane (PU) as an interfacial crosslinking agent to improve the mechanical properties of MXene films. The optimized MXene/PU (MP) nanocomposite film exhibited a tensile strength of 298.02 MPa and a toughness of 13.81 MJ m−3, surpassing those of the pure MXene film by 260 % and 1300 %, respectively. The atomic oxygen (AO) erosion yield of MP was approximately one order of magnitude lower than that of commercial Kapton films, which was attributed to the shielding effect of MXene against AO attacks. Remarkably, the MP nanocomposite film demonstrated exceptional retention of tensile strength under various extreme conditions including AO irradiation, cryogenic-high temperature, cyclic thermal shock and hot water. Contributed by multi-layer structural design and high conductivity, the MP exhibited a high electromagnetic interference shielding effectiveness (EMI SE) of 48 dB and a specific SE divided by thickness (SSE/t) of 13,479 dB cm2 g−1 at the thickness of 20 μm. Consequently, the nacre-like MP nanocomposite film with exceptional mechanical properties and high-level functional performance holds substantial promise as a multifunctional space material for LEO environments.

Dynamic imaging of micro-vibrations with an ultra-wide bandwidth and a femtometer noise using switchable pulsed laser interferometry

Imaging the complex dynamics of micro-vibrations plays a fundamental role in the investigation of microelectromechanical systems (MEMS). However, it remains a challenge for achieving both a wide bandwidth and a low noise due to the high photodetector noise and electromagnetic interference at GHz frequencies. Here, we propose a pulsed laser interferometry system with an adaptable switch to image GHz vibrations based on stroboscopic mixing, while measuring lower-frequency vibrations based on the homodyne scheme. The noise power spectral density is shown in both regions from DC to 10 GHz with an average noise down to 30.8 fm/√Hz at GHz frequencies, which holds the highest resolution to the best of our knowledge. Vibrational amplitude and phase mappings of a kHz comb-drive resonator, a GHz piezoelectric transducer, and a GHz film bulk acoustic resonator are presented with animated visualizations and k-space analysis, paving a new paradigm for the first time to image and analyze various MEMS devices of a bandwidth spanning 10 orders of magnitude.

Sandwich-Structured Mxene/Waste Polyurethane Foam Composites For Highly Efficient Electromagnetic Interference, Infrared Shielding and Joule Heating.

Electromagnetic interference (EMI) shielding and infrared (IR) stealth materials have attracted increasing attention owing to the rapid development of modern communication and military surveillance technologies. However, to realize excellent EMI shielding and IR stealth performance simultaneously remains a great challenge. Herein, a facile strategy is demonstrated to prepare high-efficiency EMI shielding and IR stealth materials of sandwich-structured MXene-based thin foam composites (M-W-M) via filtration and hot-pressing. In this composite, the conductive Ti3C2Tx MXene/cellulose nanofiber (MXene/CNF) film serves as the outer layer, which reflects electromagnetic waves and reduces the IR emissivity. Meanwhile, the middle layer is composed of a porous waste polyurethane foam (WPUF), which not only improves thermal insulation capacity but also extends electromagnetic wave propagation paths. Owing to the unique sandwich structure of "film-foam-film", the M-W-M composite exhibits a high EMI shielding effectiveness of 83.37dB, and in the meantime extremely low emissivity (22.17%) in the wavelength range of 7-14µm and thermal conductivity (0.19W m-1 K-1), giving rise to impressive IR stealth performance at various surrounding temperatures. Remarkably, the M-W-M composite also shows excellent Joule heating properties, capable of maintaining the IR stealth function during Joule heating.

Compressible thermoplastic polyurethane/silver nanorod foams for absorption dominant electromagnetic interference shielding

Conductive polymer composites (CPCs) have attracted significant interest in the field of flexible electromagnetic protection, but the challenge of balancing high electromagnetic interference shielding effectiveness (EMI SE) and low reflection losses still exists. Herein, thermoplastic polyurethane/silver nanorod (TPU/AgNR) composite foams have been successfully prepared using both the salt template and vacuum-assisted thermal compression methods. By varying the AgNRs content and employing a layer-by-layer bonding approach, a gradient structure with optimized impedance matching is achieved. The “absorb-reflect-reabsorb” EM attenuation mechanism of the asymmetric gradient EMI shielding in the internal structure is exploited, resulting in TPU/AgNR foam (TAF) with high EMI SE and significantly reduced EM reflection. Notably, the three-layer foams exhibit an average shielding efficacy of 35.5 dB and a reflected power coefficient (R) of 0.085 in the X-band, thereby substantially mitigating secondary EM wave reflections. Furthermore, these foams demonstrate exemplary compressive resilience, with the sample maintaining excellent EMI shielding stability even after undergoing 100 compression cycles at 50 % strain. Consequently, a straightforward approach is employed to fabricate materials with high EMI SE and low reflectivity, offering the potential for use in EM shielding applications of next-generation flexible electronic devices.

High‐Performance Thermoelectric and Electromagnetic Interference Shielding Derived from MXene/Ag2Se Nanowire Composite Film

AbstractA flexible n‐type composite film consisting of MXene/Ag2Se nanowires (MX‐AS), is synthesized herein via a facile wet chemical sintering process. The thermoelectric properties of the composites with various MXene concentrations are systematically explored. The as‐synthesized 2D MXene exhibits homogeneous intercalation and dispersion of the Ag2Se nanowires. A comparative analysis reveals that these composite films outperform the pristine Ag2Se nanowire films fabricated using the same process. Specifically, the MX‐AS composite film containing 1.5 wt.% MXene exhibits a significant (≈1.25 times) improvement in the maximum thermoelectric power factor (PF), exhibiting a value of ≈933.4 µW m−1 K−2 at 400 K. This enhancement can be attributed to the combination of the remarkable intrinsic Seebeck coefficient of the Ag2Se and the high electrical conductivity of the MXene. Moreover, cyclic bending tests demonstrate the exceptional mechanical durability and flexibility of the composite film, with only an ≈7% decrease in the PF after 1000 cycles. In addition, the as‐prepared MX‐AS composite exhibits a high electromagnetic interference (EMI) shielding efficiency.