High Energy Storage Efficiency Research Articles

Molecular Photoelectrochemical Energy Storage Materials for Coupled Solar Batteries.

ConspectusSolar-to-electrochemical energy storage is one of the essential solar energy utilization pathways alongside solar-to-electricity and solar-to-chemical conversion. A coupled solar battery enables direct solar-to-electrochemical energy storage via photocoupled ion transfer using photoelectrochemical materials with light absorption/charge transfer and redox capabilities. Common photoelectrochemical materials face challenges due to insufficient solar spectrum utilization, which restricts their redox potential window and constrains energy conversion efficiency. In contrast, molecular photoelectrochemical energy storage materials are promising for their mechanism of exciton-involved redox reaction that allows for extra energy utilization from hot excitons generated by superbandgap excitation and localized heat after absorption of sub-bandgap photons. This enables more efficient redox reactions with a less restricted redox potentials window and, thus, better utilization of the full solar spectrum. Despite these advantages, practical application remains elusive due to the mismatch between the short lifetime of the charge separation state (<ns) and the slower redox reaction rate (>μs). This mismatch results in a significant portion of the photogenerated charges recombining before participating in desired electrochemical energy storage reactions, leading to diminished overall efficiency. It is therefore highly important to develop molecular materials with intrinsic prolonged charge separation state and extrinsic effective mass-electron transfer to enable efficient coupled solar batteries for practical applications.In this Account, we begin with an introduction of the general solar-to-electrochemical energy storage concept based on molecular photoelectrochemical energy storage materials, highlighting the advantages of periodic oxidative donor-reductive acceptor porous aggregate structures that have synergistic implications on charge separation state lifetime extension and mass-electron transfer. We then present our earliest trial on the design and application of molecular photoelectrochemical energy storage materials, which stimulated our subsequent studies on tuning electron donor and acceptor structures for enhanced charge separation and diverse photoelectrochemical redox reactions. Moreover, we introduce the best practices in the design and assembly of various coupled solar battery devices, along with our literature contributions and progresses in solar-to-electrochemical energy storage efficiency (ηSES) over nearly the past decade. Finally, we conclude by highlighting the universality of our strategies as essential design principles, spanning from regulating long-lived charge separation states and photocoupled ion transfer processes in molecular materials to the construction of efficient coupled solar batteries. We offer perspectives on the synergy between photovoltage and redox potentials and the practical significance of 3D printing, providing key evaluation indicators for large-scale application. This Account provides molecular level insights for the construction of high-efficiency photoelectrochemical energy storage materials and guidance for practical solar-to-electrochemical energy storage applications.

Antiferroelectric domain modulation enhancing energy storage performance by phase-field simulations

Antiferroelectric materials represented by PbZrO3(PZO) have excellent energy storage performance and are expected to be candidates for dielectric capacitors. It remains a challenge to further enhance the effective energy storage density and efficiency of PZO-based antiferroelectric films through domain engineering. In this work, the effects of three variables, misfit strain between the thin film and substrate, defect dipoles doping, and film thickness, on the domain structure and energy storage performance of PZO-based antiferroelectric materials are comprehensively investigated via phase-field simulations. The results show that applying tensile strain to the films can effectively increase the transition electric field from antiferroelectric to ferroelectric. In addition, the introduction of defect dipoles while applying tensile strain can significantly reduce the hysteresis and improve energy storage efficiency. Ultimately, a recoverable energy density of 38.3 J/cm3 and an energy storage efficiency of about 89.4% can be realized at 1.5% tensile strain and 2% defect dipole concentration. Our work provides a new idea for the preparation of antiferroelectric thin films with high energy storage density and efficiency by domain engineering modulation.

Excellent energy storage properties in ZrO2 toughened Ba0.55Sr0.45TiO3-based relaxor ferroelectric ceramics via multi-scale synergic regulation

Lead-free ceramic capacitors offer ultrahigh power density and ultrafast discharging rates, making them critical energy storage components for advanced pulsed power systems. However, the greatest obstacle to broader applications remains the relatively low energy storage density. In this study, a relaxor ferroelectric ceramic based on (0.6-x)Ba0.55Sr0.45TiO3-0.4Bi0.5Na0.5TiO3-xSrZrO3 ((0.6-x)BST-0.4BNT-xSZ) is prepared using the tape casting method, resulting in an excellent energy density (Wrec ≈ 10.0 J cm−3) and high energy storage efficiency (η ≈ 91 %). The solid solution of linear dielectrics SrZrO3 synergistically regulates both relaxor properties and breakdown strength. The variation of relaxor property was explored utilizing New Glass model and the multi-polarization model, with confirmation provided by piezoresponse force microscopy. Furthermore, the breakdown strength could be attributed to improvements in electric insulation and the widening of the bandgap. As SrZrO3 content increases, the in-situ emergence of the second phase ZrO2, accompanied by a martensitic transformation, not only improves the fracture toughness of ceramics but also serves to elongate the breakdown path. Encouragingly, x = 0.20 ceramics also achieve excellent temperature stability (−95–125 ℃), frequency stability (1–1000 Hz), cycling reliability (1–106 cycles), and great charging-discharging properties. This multiscale synergic regulation strategy plays a guiding role in the screening of high-performance energy storage dielectric materials.

A study on novel dual-functional photothermal material for high-efficient solar energy harvesting and storage

The solar-heat storage efficiency of devices based on phase change materials (PCMs) is limited due to the light absorption and internal heat transfer within the PCMs, unclear thermal conductivity-enhancement mechanism within nanocomposite PCMs, and uncontrollable photothermal-interface modulation. Therefore, a novel controllable strategy was proposed in this study to fabricate dual-functional photothermal storage three-dimensional (3D) phase change blocks (PCBs) with higher thermal conductivity (27.98 W/m·K) and spectral absorption (98.03 %) compared to those of most previously reported PCM-based devices. The as-synthesized PCBs contained millimeter-sized graphite plates with horizontal Van der Waals bonds and oriented micro/nanoscale graphite nanosheets. The structural properties of thin PCM layers between the PCB sheets have synergistically reduced the internal interfacial thermal resistance of the PCBs. Laser-controllable induction was used to fabricate integrated biomimetic-forest 3D optical absorbers on the high thermal conductivity interface of the PCBs, which significantly reduced the thermal resistance of the optical-thermal interface. The resulting 3D-PCBs, integrated with thermoelectric generators, powered portable electronic devices, expanding the applications of traditional PCM heat-storage devices. Therefore, this study will guide the future design of high-performance solar-thermal storage PCMs with a wide range of practical applications.

Achieving high energy storage density and efficiency in (Na0.5Bi0.5)TiO3-based lead-free ceramics

Due to the demands of miniaturization, weight reduction and green development for electronic devices, development of lead-free dielectric ceramic capacitors with high recoverable energy density (Wrec) and energy storage efficiency (η) attracts much attention. To this end, (1-x)[0.75(Na0.5Bi0.5)TiO3-0.25SrTiO3]-xNdNbO4 (abbreviated as: NBST-xNN) ceramics were fabricated through a solid-state reaction method. After adding NN, the non-perovskite phase of Bi2Ti2O7 (BTO) with low dielectric constant (εr) and loss (tan δ) is generated. Finite element software (COMSOL) was used to explore the influence of the BTO phase on breakdown strength (Eb). The simulation result indicates that the BTO phase with a low εr concentrates a larger local electric field (LEF), and thus weakens the LEF loading in the main perovskite phase, which is beneficial for enhancing Eb. Moreover, NN doping significantly decreases the oxygen vacancy concentration in NBST ceramics, which plays a key role in improving Eb. On the other hand, as NN content increases, the hysteresis of the polarization (P)-electric field (E) loops is substantially suppressed, and the polarization saturation is delayed, which can be ascribed to the appearance of the BTO phase having a linear dielectric characteristic and to the enhanced fluctuations of composition and charge by NN doping. Benefitting from the above factors, the optimal energy storage performance (ESP) with a Wrec of 4.14 J/cm3 and an η of 90 % is obtained in NBST-0.08NN ceramics. Meanwhile, the ESP of NBST-0.08NN ceramics shows good charge-discharge properties and thermal stability. In conclusion, these results demonstrate that NBST-0.08NN ceramics are promising candidates as environment-friendly dielectric capacitor materials.

Surface plasma treatment boosting antiferroelectricity and energy storage performance of AgNbO3 film

The utilization of AgNbO3 film in dielectric energy storage poses challenges due to its susceptibility to impurity phase formation, which compromises its antiferroelectric properties and breakdown electric field. In this study, we successfully fabricated an AgNbO3 film with outstanding antiferroelectric properties and energy storage capabilities by employing oxygen ion surface plasma technology in conjunction with the sol-gel method. Our results demonstrate that the surface of the AgNbO3 film undergoes a layer-by-layer treatment using oxygen ion plasma, effectively suppressing impurity phases and oxygen vacancies formation while reducing grain size and enhancing insulation performance. The AgNbO3 film, which has undergone surface plasma treatment with oxygen ion, exhibits exceptional characteristics as an antiferroelectric material by demonstrating an impressive energy storage density of 13.13J/cm3 and a high energy storage efficiency of 56%. Overall, we present a straightforward and viable approach for fabricating high-performance AgNbO3 films for efficient dielectric energy storage.

(Sb0.5Li0.5)TiO3-Doping Effect and Sintering Condition Tailoring in BaTiO3-Based Ceramics.

(1-x)(Ba0.75Sr0.1Bi0.1)(Ti0.9Zr0.1)O3-x(Sb0.5Li0.5)TiO3 (abbreviated as BSBiTZ-xSLT, x = 0.025, 0.05, 0.075, 0.1) ceramics were prepared via a conventional solid-state sintering method under different sintering temperatures. All BSBiTZ-xSLT ceramics have predominantly perovskite phase structures with the coexistence of tetragonal, rhombohedral and orthogonal phases, and present mainly spherical-like shaped grains relating to a liquid-phase sintering mechanism due to adding SLT and Bi2O3. By adjusting the sintering temperature, all compositions obtain the highest relative density and present densified micro-morphology, and doping SLT tends to promote the growth of grain size and the grain size distribution becomes nonuniform gradually. Due to the addition of heterovalent ions and SLT, typical relaxor ferroelectric characteristic is realized, dielectric performance stability is broadened to ~120 °C with variation less than 10%, and very long and slim hysteresis loops are obtained, which is especially beneficial for energy storage application. All samples show extremely fast discharge performance where the discharge time t0.9 (time for 90% discharge energy density) is less than 160 ns and the largest discharge current occurs at around 30 ns. The 1155 °C sintered BSBiTZ-0.025SLT ceramics exhibit rather large energy storage density, very high energy storage efficiency and excellent pulse charge-discharge performance, providing the possibility to develop novel BT-based dielectric ceramics for pulse energy storage applications.

Achieving high energy storage performance in PbHfO3-based antiferroelectric ceramics by Sr element doping

Antiferroelectric (AFE) ceramics are the most promising material system for energy storage in dielectric capacitors due to their fast charging-discharging rate, good chemical stability, and high energy storage density. However, it is exceedingly challenging to simultaneously achieve the excellent recoverable energy density (Wre) and high energy storage efficiency (η) at present. In this work, (Pb0.925-xSrxLa0.05)(Hf0.95Ti0.05)O3 AFE ceramics with various Sr contents are fabricated by solid-state sintering processing. It has been found that Sr-doping in the A-site can significantly affect the microstructure, including reducing grain size and modulation period, effectively strengthening the antiferroelectricity, which is responsible for the improved energy storage performance. The high recoverable energy storage density of 10.2 J/cm3 is obtained at 560 kV/cm with an ultra-high efficiency of 93.0% in (Pb0.875Sr0.05La0.05)(Hf0.95Ti0.05)O3 ceramics. These features suggest that Sr-doped PbHfO3-based AFE ceramics can serve as promising candidates for capacitor materials, offering significant potential in the realm of energy storage applications.

Influence of sintering temperature on electrocaloric and energy storage properties of sol-gel derived lead-free BaHf0.20Ti0.80O3 ferroelectric ceramics for sustainable energy solutions

Ferroelectric materials have emerged as intriguing contenders for a variety of applications in the ongoing effort to look for sustainable energy solutions, including energy storage and solid-state cooling systems. In this work, a systematic investigation has been conducted on the microstructural, dielectric, electrocaloric, and energy storage characteristics of sol-gel elaborated BaHf0.20Ti0.80O3 (BHT) ferroelectric ceramics. The structural investigation by Raman and X-ray diffraction indicated that when the sintering temperature increases, the tetragonality of BHT ceramics reduces, and the evolution of the cubic phase increases. The evolution of the microstructure in BHT ceramics is found to be significantly reliant on the sintering temperature. With increasing temperature of sintering, the bulk density of BHT ceramics increases. The improved dielectric and ferroelectric properties were attained in BHT ceramics at higher sintering temperatures. The BHT ceramic sintered at 1350 °C exhibited a maximum electrocaloric temperature change of ΔT ∼0.6 °C with a corresponding efficiency ΔT/ΔE of 0.3 K mm/kV near ambient temperature under a low electric field of 20 kV/cm. The BHT ceramic sintered at 1450 °C exhibited excellent room temperature recoverable energy density of JRec ∼67.84 10−3J/cm3 and high energy storage efficiency of η ∼75.13 % under a low electric field of 20 kV/cm. The highest JRec ∼73.22 10−3J/cm3 with corresponding η of 64.60 % were obtained in BHT ceramic sintered at temperature 1350 °C. These findings broaden the possibility of exploring BHT-based systems as efficient lead-free ferroelectrics for both solid-state refrigeration and energy storage applications.

Simultaneously enhanced of energy storage and energy harvesting performances of [(Bi0.5Na0.5)TiO3–BaTiO3] ceramics by addition of SrTiO3

As is well known, relaxor dielectrics are characterized by high energy storage efficiency (η), while high recoverable energy storage density (Wrec) can be achieved by anti-ferroelectric ceramics. Herein, our approach is to find relaxor- anti-ferroelectric coexistence phases of (Bi0.5Na0.5)TiO3- BaTiO3 ceramics for achieving high performance in energy storage and energy harvesting as well. Therefore, [(0.9-x) ( Bi0.5Na0.5)TiO3-xSrTiO3-0.1BaTiO3] (abbreviation (0.9-x) NBT-0.1BT-xST) (0.0 ≤ x ≤ 0.4) were synthesized via the solid-state reaction route in air. The tolerance factor (τ) increased from 0.9901 to 0.9998 when ST-content increased from 0.0 to 0.4, indicating an increase in crystal lattice symmetry. The FT-IR de-convolution vibration modes shown in the TiO6 octahedra exhibit two peaks at ∼550 and 650 cm−1, which indicate present coexistence phases of the crystal structure. Ferroelectric to relaxor phase crossover has been detected by the addition of ST with the present anti-ferroelectric phase in particular dopant ST = 0.2. The increasing into the diffused phase transition (γ) is signified by enhancement of the relaxor degree of NBT-BT at high content of ST. The rapidly suppressed remnant polarization (Pr) at high content of ST is due to substitute iso-valence (Sr2+) by tri-valence (Bi3+) and mono-valence (Na1+). Ultrahigh Wrec = 1.13 J/ cm3 with excellent η = 92.62% were obtained at ST = 0.3 at low electric field (E = 110 kV cm−1). A remarkable response of the strain with a high converse piezoelectric coefficient ( d33* = 390.47 pm V−1) at ST = 0.2 was obtained due to decreasing the non-revisable 180° domain switching. Based on the obtained results, the addition of ST to NBT-BT ceramics can provide a head start in the implementation of ceramic capacitors for potential effective into energy harvesting and energy storage applications.

Innovative Design of BNKT-xSLZT Ceramics: Maximizing the Polarization Difference for Enhanced Energy Storage.

Lead-free relaxor ferroelectric ceramics with outstanding energy-storage (ES) density (Wrec) and high ES efficiency (η) are crucial for advanced pulse-power capacitors. This study introduces a strategic approach to maximizing the polarization difference (ΔP) by inducing a transition from the ferroelectric phase to the ergodic relaxor (ER) phase. By employing this strategy, a series of ceramics, (1 - x)(Bi0.5Na0.4K0.1)TiO3-x(Sr0.85La0.1)(Zr0.5Ti0.5)O3 (BNKT-xSLZT), with varying SLZT content (x = 0.05, 0.10, 0.15, and 0.20), were designed. The addition of SLZT enhances cationic disorder, induces vacancies at A sites, and disrupts long-range ferroelectric order, facilitating the formation of polar nanoregions and enhancing relaxor ferroelectric behavior. Furthermore, a viscous polymer process (VPP) technology is employed to optimize the ceramics' structure, aiming to increase the breakdown strength (Eb) and enhance ΔP. Ultimately, enhanced ES performance is demonstrated in BNKT-0.15SLZTVPP, achieving a remarkable Wrec of 6.85 J/cm3 and η of 84% under 470 kV/cm. This composition demonstrates excellent stability with minimal variations in Wrec (3.0%) and η (4.4%) over the temperature range of 20-110 °C. Additionally, BNKT-0.15SLZTVPP exhibits exceptional pulse charge-discharge properties, featuring a high discharge density of 3.72 J/cm3, a large power density of 164.2 MW/cm3, and a short discharge time (t0.9) of 193 ns under 300 kV/cm. The study validates the practicality of BNKT-0.15SLZTVPP for pulse capacitors and underscores the potential to enhance ES performance through A-site donor doping and VPP technology. This work provides a comprehensive understanding of the interplay among composition, structure, and ES properties in lead-free relaxor dielectric ceramics, laying the groundwork for innovative advancements in the field.

Recent Development on Transition Metal Oxides-Based Core-Shell Structures for Boosted Energy Density Supercapacitors.

In recent years, nanomaterials exploration and synthesis have played a crucial role in advancing energy storage research, particularly in supercapacitor development. Researchers have diversified materials, including metal oxides, chalcogenides, and composites, as well as carbon materials, to enhance energy and power density. Balancing energy density with electrochemical stability remains challenging, driving intensified efforts in advancing electrode materials. This review focuses on recent progress in designing and synthesizing core-shell materials tailored for supercapacitors. The core-shell architecture offers advantages such as increased surface area, redox active sites, electrical conductivity, ion diffusion kinetics, specific capacitance, and cyclability. The review explores the impact of core and shell materials, specifically transition metal oxides (TMOs), on supercapacitor electrochemical behavior. Metal oxide choices, such as cobalt oxide as a preferred core and manganese oxide as a shell, are discussed. The review also highlights characterization techniques for assessing structural, morphological, and electrochemical properties of core-shell materials. Overall, it provides a comprehensive overview of ongoing TMOs-based core-shell material research for supercapacitors, showcasing their potential to enhance energy storage for applications ranging from gadgets to electric vehicles. The review outlines existing challenges and future opportunities in evolving TMOs-based core-shell materials for supercapacitor advancements, holding promise for high-efficiency energy storage devices.

Optimize energy storage performance of NaNbO3 ceramics by multivariable control strategy

NaNbO3 ceramics have broad application prospects in ultra-high power electronic systems, electromagnetic pulses, and other applications. In this study, (1-y)[(1-x)NaNbO3-xSmMg0.5Zr0.5O3]-y(Bi0.5Na0.5)0.7Sr0.3TiO3 (x = 0.06, 0.08 and 0.10)(y = 0.30, 0.35, 0.40 and 0.45) ceramics were fabricated. The effects of the incorporation of SmMg0.5Zr0.5O3 (SMZ) and (Bi0.5Na0.5)0.7Sr0.3TiO3 (BNST) on the energy storage performance, impedance, actual charge and discharge capacity, phase structure and microstructure of the ceramic samples were analyzed. Finally, when x = 0.08, and y = 0.35, the recoverable energy storage density of the sample was 5.8 J/cm3 and a high energy storage efficiency of 88 % was obtained at 545 kV/cm. In addition, the ceramic maintains a stable actual charge and discharge capacity and an extremely fast discharge time (16.1 ns) in a wide temperature range (20–160 °C). These excellent energy-storage performances may be due to the fine grain size and large relaxation and activation energies.

High-performance Ti-doped strontium cobaltite perovskites as oxygen electrodes in solid oxide cells

Oxygen electrodes play a vital role in realizing high-performance solid oxide cells (SOCs) with high roundtrip efficiency, large-scale capacity, and long-term stability energy storage. This paper constructs Ti-doped strontium cobaltite perovskites (SrCo1-xTixO3-δ, SCTx, x = 0.2, 0.3, 0.4, 0.5) as newly stable oxygen electrodes for SOCs. The changes of oxygen vacancy in SCTx with Ti-doped concentration are investigated by X-ray photoelectron spectroscopy (XPS). The results show that the content of oxygen vacancy decreases with the enrichment of Ti doping. The area-specific resistance (ASR) of the symmetrical cell with SrCo0.8Ti0.2O3-δ (SCT2) electrode is only 0.013 Ω cm2 at 850 °C in air. The single cell with SCT2 oxygen electrode achieves the peak power density of 1.313 W cm−2 at 850 °C under humidified H2 conditions in fuel cells mode, and the current density reaches 2.95 A cm−2 under an electrolytic voltage of 1.9 V at 850 °C for CO2 electrolysis. The Density functional theory (DFT) calculations confirm that the oxygen vacancy formation energy is the lowest when the ratio of Ti to Co is 2:8, verifying the superior property of SCT2. This study comes up with a creation for developing high-stability and high-activity oxygen electrode materials that can be used for energy storage systems.

A new anode material for high rate and long life lithium/sodium storage

It is imperative to design suitable anode materials for both lithium-ion (LIBs) and sodium-ion batteries (SIBs) with a high-rate performance and ultralong cycling life. We fabricated a MoO2/MoS2 heterostructure that was then homogeneously distributed in N,S-doped carbon nanofibers (MoO2/MoS2@NSC) by electrospinning and sulfurization. The one-dimensional carbon fiber skeleton serves as a conductive frame to decrease the diffusion pathway of Li+/Na+, while the N/S doping creates abundant active sites and significantly improves the ion diffusion kinetics. Moreover, the deposition of MoS2 nanosheets on the MoO2 bulk phase produces an interface that enables fast Li+/Na+ transport, which is crucial for achieving high efficiency energy storage. Consequently, as the anode for LIBs, MoO2/MoS2@NSC gives an excellent cycling stability of 640 mAh g−1 for 2 000 cycles under 5.0 A g−1 with an ultralow average capacity drop of 0.002% per cycle and an exceptional rate capability of 614 mAh g−1 at 10.0 A g−1. In SIBs, it also produces a significantly better electrochemical performance (reversible capacity of 242 mAh g−1 under 2.0 A g−1 for 2 000 cycles and 261 mAh g−1 under 5.0 A g−1). This work shows how introducing a novel interface in the anode can produce rapid Li+/Na+ storage kinetics and a long cycling performance.

HsGDY 3D Framework-Encapsulated Cu2O Quantum Dots for High-Efficiency Energy Storage.

Nanostructured electrode materials become a vital component for future electrode materials because of their short electron and ion transport distances for fast charge and discharge processes and sufficient space between particles for volume expansion. So, achieving a smaller size of the nanomaterial with stable structure and high electrode performance is always the pursuit. Herein, the hybrid electrode material system hydrogen-substituted graphdiyne (HsGDY)/Cu2O-quantum dots (QDs) composed of an active carbon substrate and vibrant metal oxide QD load was established by HsGDY and cuprous oxide. The HsGDY frame with conjugated structure not only delivers impressive capacity by a self-exchange mechanism but also characterizes a matrix to forge strong connections with numerous active Cu2O-QDs for the prevention of aggregation, leading to a homogeneous storage and transport of charge in a bulk material of crisscross structural pores. QD-based electrode materials would exhibit desired capacities by their large surface area, abundant active surface atoms, and the short diffusion pathway. The hybrid system of HsGDY/Cu2O-QDs delivers an ultrahigh capacity of 1230 mA h g-1 with loading density reaching up to 1 mg cm-2. In the meantime, the electrode exhibits a long cycle stability of over 8000 cycles. The synergistic effect endows the hybrid system electrode with an approximately theoretical energy density, suggesting the great potential of such carbon/QD hybrid material system applied for high-performance batteries.

Phase change materials encapsulated in a novel hybrid carbon skeleton for high-efficiency solar-thermal conversion and energy storage

Phase change materials (PCMs) with high energy density and stationary transition temperature are now considered promising solar energy storage mediums. However, their intrinsic poor light absorption, thermal conductivity and stability severely impede their potential applications. In this study, a novel carbonized hybrid aerogel (CHA) structure was firstly constructed by incorporating MXene and carbon nanofibers (CNFs) into a continuous phase polyamic acid salt (PAAS) aqueous solution, followed by directional freezing, vacuum drying, imidization, and carbonization processes. Finally, the composite PCMs (CPCMs) were fabricated by vacuum impregnation of PCMs into the CHAs. The CPCM, of which CHA consists of 20 wt% MXene and 10 wt% CNF@PDA, demonstrates high solar-thermal conversion efficiency (>91 %), improved thermal conductivity of 0.40 W·m−1·K−1, great thermal stability (enthalpy loss < 0.19 % after 100 cycling tests with no obvious leakage). The introduction of MXene and CNFs endows PCM with broader light absorption spectrum range. The skeleton matrix embedded with bonded MXene sheets and CNFs provides more thermal pathways, light absorption sites and carrying capacity, improves the thermal conductivity, solar-thermal conversion property and stability of PCM. In addition, CPCM also exhibits outstanding EMI SE (95 dB). The multifunctional and high-performance CPCMs shows potential to realize the effective capture and utilization of solar energy. This work provides a new strategy to construct stable and multifunctional hybrid carbon skeleton for high-efficiency solar-thermal conversion and energy storage.

A multi-scale modeling of Ca-based material for solar-driven calcium-looping energy storage process: From calcination reactor to energy carrier

The calcium looping (CaL) for thermochemical energy storage possesses a great potential to promote solar thermal utilization. However, the performance of CaL, especially for the Ca-based energy carrier, cannot satisfy the expectations of industrial application, requiring enhancement between multiple length scales. Hence, a model for solar-driven CaL energy storage process, coupled by three-dimensional reactor, two-dimensional light field and one-dimensional particle models, is proposed to study the multiprocess behavior on particle flow, photothermal conversion, calcination reaction, heat-mass transfer and stress response. It is found that moving-bed reactor contributes to achieving continuous calcination and reducing particle waste, while the rapid bouncing particles inhibit the performance of single particle, with up to 45.7 % reduction in conversion. Additionally, energy carrier with stable and continuous flow normally yields high energy storage efficiency and cycle stability when the conversion of outlet particle is closed to 1 and thermal stress is less than 50 MPa.

Integrated operation and efficiency analysis of CaCO3/CaO in a fixed-bed reactor for thermochemical energy storage

Calcium-based thermochemical energy storage (TCES) has attracted much attention in solar energy utilization and storage. However, the investigations of the CaCO3/CaO system are incomplete and poorly integrated at the reactor scale. In this work, a fixed-bed reactor for calcium looping (CaL) is used to conduct the integrated operation of energy storage and release. The decomposition conversion of CaCO3 in N2 at 850 °C for 8 h is 63.8% and the carbonation conversion of the corresponding decomposition product is 67.2% in CO2 at 750 °C for 4 h. The lower reactor filling increases overall thermal energy storage efficiency but decreases released energy. Furthermore, a simulation model is built to study the key operation parameters that greatly affect reactor performances. According to the orthonormal design, the high calcination temperature and porosity of 0.6–0.7 are key factors to improve both high thermal energy storage efficiency and released energy. The carbonation temperature and thermal conductivity are less important factors than decomposition temperature and porosity, which can be adjusted flexibly to meet the needs of heat utilization and cost reduction. This work provides valuable guidance for optimizing reactor operation and modifying materials to achieve high overall efficiency and released energy in fixed-bed reactors.

Enhanced recoverable energy storage density and breakdown strength in cation-site modified K0·5Bi0·5TiO3-based ergodic relaxor ferroelectric

Bi-containing ferroelectrics like Na0·5Bi0·5TiO3 (NBT) and K0·5Bi0·5TiO3 (KBT)-based materials are extensively investigated to achieve high recoverable energy storage density (Wrec) and efficiency (η). In this work, Bi-site modified KBT-based compositions have been studied for energy storage application at room temperature. KBT has been transformed from a non-ergodic to an ergodic relaxor state through the Eu3+ substitution. High breakdown voltage and slim polarization vs electric field loop are observed in 6 mol% Eu3+-substituted KBT, and high maximum polarization (Pmax) is retained along with low remnant polarization (Pr) in this composition. These features help to attain the Wrec and efficiency of 1.3 J/cm3 and 72%, respectively in 6 mol% Eu3+-substituted KBT at room temperature. This work demonstrates a strategy to enhance the Wrec and η by forming a stable ergodic relaxor state in the KBT-based material.