High-Concentration Monoclonal Antibody Formulations Research Articles

The Osmolality and Hemolysis of High-Concentration Monoclonal Antibody Formulations.

Highly concentrated monoclonal antibody (mAb) formulations for subcutaneous administration are becoming increasingly preferred within the biopharmaceutical industry for ease of use and improved patient compliance. A common phenomenon observed in the industry is that osmolality detected via freezing-point depression (FPD) in high-concentration mAb formulations is much higher than the theoretical concentrations, yet the occurrence of this phenomenon and its possible safety issues have been rarely reported. The current study summarized theoretical osmolality of U.S. Food and Drug Administration approved high-concentration mAb formulations and evaluated effects of high osmolality on safety using hemolysis experiments for the first time. Two mAbs formulated at 150mg/mL were used as models and configured into two isotonic solutions: a, a theoretically calculated molarity in the isotonic range (H) and b, an osmolality value measured via the FPD in the isotonic range (I). The H and I formulations of each mAb were individually subjected to hemolysis experiments, and the hemolysis rates of the two formulations of the same mAb were compared. Besides, the effect of mAb concentration on osmolality detected by FPD was explored as well. The results indicated that the hemolysis rates were similar between the H and I formulations of mAbs at the same sample addition volume, and the osmolality values increased approximately linearly with the increase in mAb concentration. High osmolality for high-concentration mAb formulations would not affect product safety and the excipients could be added at relatively high levels to maintain product stability, especially for labile products.

Predicting Colloidal Stability of High-Concentration Monoclonal Antibody Formulations in Common Pharmaceutical Buffers Using Improved Polyethylene Glycol Induced Protein Precipitation Assay.

Colloidal stability is an important consideration when developing high concentration mAb formulations. PEG-induced protein precipitation is a commonly used assay to assess the colloidal stability of protein solutions. However, the practical usefulness and the current theoretical model for this assay have yet to be verified over a large formulation space across multiple mAbs and mAb-based modalities. In the present study, we used PEG-induced protein precipitation assays to evaluate colloidal stability of 3 mAbs in 24 common formulation buffers at 20 and 5 °C. These prediction assays were conducted at low protein concentration (1 mg/mL). We also directly characterized high concentration (100 mg/mL) formulations for cold-induced phase separation, turbidity, and concentratibility by ultrafiltration. This systematic study allowed analysis of the correlation between the results of low concentration assays and the high concentration attributes. The key findings of this study include the following: (1) verification of the usefulness of three different parameters (Cmid, μB, and Tcloud) from PEG-induced protein precipitation assays for ranking colloidal stability of high concentration mAb formulations; (2) a new method to implement PEG-induced protein precipitation assay suitable for high throughput screening with low sample consumption; (3) improvement in the theoretical model for calculating robust thermodynamic parameters of colloidal stability (μB and εB) that are independent of specific experimental settings; (4) systematic evaluation of the effects of pH and buffer salts on colloidal stability of mAbs in common formulation buffers. These findings provide improved theoretical and practical tools for assessing the colloidal stability of mAbs and mAb-based modalities during formulation development.

Stable High-Concentration Monoclonal Antibody Formulations Enabled by an Amphiphilic Copolymer Excipient.

Monoclonal antibodies are a staple in modern pharmacotherapy. Unfortunately, these biopharmaceuticals are limited by their tendency to aggregate in formulation, resulting in poor stability and often requiring low concentration drug formulations. Moreover, existing excipients designed to stabilize these formulations are often limited by their toxicity and tendency to form particles such as micelles. Here, we demonstrate the ability of a simple "drop-in", amphiphilic copolymer excipient to enhance the stability of high concentration formulations of clinically-relevant monoclonal antibodies without altering their pharmacokinetics or injectability. Through interfacial rheology and surface tension measurements, we demonstrate that the copolymer excipient competitively adsorbs to formulation interfaces. Further, through determination of monomeric composition and retained bioactivity through stressed aging, we show that this excipient confers a significant stability benefit to high concentration antibody formulations. Finally, we demonstrate that the excipient behaves as an inactive ingredient, having no significant impact on the pharmacokinetic profile of a clinically relevant antibody in mice. This amphiphilic copolymer excipient demonstrates promise as a simple formulation additive to create stable, high concentration antibody formulations, thereby enabling improved treatment options such as a route-of-administration switch from low concentration intravenous (IV) to high concentration subcutaneous (SC) delivery while reducing dependence on the cold chain.

Application of thin gap rheometry for high shear rate viscosity measurement in monoclonal antibody formulations

The key highlight of this work was to develop a thin gap methodology on a mechanical rheometer for characterizing high concentration monoclonal antibody formulations. This work was done from applied formulation perspective to provide guidance on an additional measurement protocol with the objective of further reducing sample volume requirement for biopharmaceutical formulation rheology measurements and provide viscosity data over a wide shear rate range. This is especially relevant for early stage discovery where there are sample volume limitations. This developed methodology in addition to an understanding of the diffusion interaction parameter was then in turn utilized to elucidate the effect of surfactants and excipients on the high shear rate viscosity of high concentration monoclonal antibodies. In this study, gap dependent changes in the fundamental rheological behavior were observed. At higher gaps, an initial shear thinning behavior was observed at lower shear rates and this trend was found to disappear at thin gaps. This shear thinning which is due to air water interface disappears as the gap size decreases. At high shear rates, there is a convergence of all the viscosity data for all the gaps. This also converges with the mVROC data. However, at smallest gaps studied (50 µm) shear thickening is observed at intermediate shear rates. This maybe attributable to the protein molecules undergoing flow induced aggregation due to increased confinement thereby causing shear thickening and an increase in viscosity. However, this trend eventually diminishes at higher shear rates which could be attributed to flow induced alignment of protein aggregates thereby causing a decrease in viscosity. Addition of either excipients (like Arginine- HCl, NaCl) or surfactants (like polysorbate80) seem to have a drastic impact on shear thickening caused potentially by flow induced aggregation. Addition of excipients also resulted in approximately 33–50% decrease in the viscosity of monoclonal antibody (mAb) solution and the diffusion interaction parameter kD was seen to be indicative of the high shear rate viscosity behavior of these formulations.

A Formulation Development Approach to Identify and Select Stable Ultra–High-Concentration Monoclonal Antibody Formulations With Reduced Viscosities

High protein concentration formulations are required for low-volume administration of therapeutic antibodies targeted for subcutaneous, self-administration by patients. Ultra-high concentrations (≥150 mg/mL) can lead to dramatically increased solution viscosities, which in turn can lead to stability, manufacturing, and delivery challenges. In this study, various categories and individual types of pharmaceutical excipients and other additives (56 in total) were screened for their viscosity reducing effects on 2 different mAbs. The physicochemical stability profile, as well as viscosity ranges, of several candidate antibody formulations, identified and designed based on the results of the excipient screening, were evaluated over a 6-month time period under accelerated and real-time storage conditions. In addition to reducing the solution viscosities to acceptable levels for parenteral administration (using currently available and acceptable delivery devices), the candidate formulations did not result in notable losses of physicochemical stability of the 2 antibodies on storage for 6 months at 25°C. The experiments described here demonstrate the feasibility of a formulation development and selection approach to identify candidate high-concentration antibody formulations with viscosities within pharmaceutically acceptable ranges that do not adversely affect their physicochemical storage stability.

Multi-criteria manufacturability indices for ranking high-concentration monoclonal antibody formulations.

ABSTRACTThe need for high‐concentration formulations for subcutaneous delivery of therapeutic monoclonal antibodies (mAbs) can present manufacturability challenges for the final ultrafiltration/diafiltration (UF/DF) step. Viscosity levels and the propensity to aggregate are key considerations for high‐concentration formulations. This work presents novel frameworks for deriving a set of manufacturability indices related to viscosity and thermostability to rank high‐concentration mAb formulation conditions in terms of their ease of manufacture. This is illustrated by analyzing published high‐throughput biophysical screening data that explores the influence of different formulation conditions (pH, ions, and excipients) on the solution viscosity and product thermostability. A decision tree classification method, CART (Classification and Regression Tree) is used to identify the critical formulation conditions that influence the viscosity and thermostability. In this work, three different multi‐criteria data analysis frameworks were investigated to derive manufacturability indices from analysis of the stress maps and the process conditions experienced in the final UF/DF step. Polynomial regression techniques were used to transform the experimental data into a set of stress maps that show viscosity and thermostability as functions of the formulation conditions. A mathematical filtrate flux model was used to capture the time profiles of protein concentration and flux decay behavior during UF/DF. Multi‐criteria decision‐making analysis was used to identify the optimal formulation conditions that minimize the potential for both viscosity and aggregation issues during UF/DF. Biotechnol. Bioeng. 2017;114: 2043–2056. © 2017 The Authors. Biotechnology and Bioengineering Published by Wiley Perodicals, Inc.

Filling of High-Concentration Monoclonal Antibody Formulations: Investigating Underlying Mechanisms That Affect Precision of Low-Volume Fill by Peristaltic Pump.

Vial and syringe filling by peristaltic pump is considered a well-established manufacturing process and has been implemented by numerous contract manufacturing organizations and biopharmaceutical companies. However, its technical details and associated critical process parameters on fill weight precision are rarely published. Such information on high-concentration/viscosity formulation filling is particularly lacking. This study aimed to identify critical filling parameters that dictate a tight control on fill weight precision. The findings of this study indicate that mitigating suck-back height variation is the key to achieving improved fill weight precision. Liquid properties, the influence of liquid/nozzle interactions, and pressure variations during suck-back are inherent to fill weight variations. Optimizing fill weight precision by manipulating pump system parameters is not a root-cause solution. The outcomes of this study will benefit scientists and engineers who develop pre-filled syringe/vial products by providing a better understanding of high-concentration formulation filling principles and challenges.

Solubility Challenges in High Concentration Monoclonal Antibody Formulations: Relationship with Amino Acid Sequence and Intermolecular Interactions

The purpose of this work was to elucidate the molecular interactions leading to monoclonal antibody self-association and precipitation and utilize biophysical measurements to predict solubility behavior at high protein concentration. Two monoclonal antibodies (mAb-G and mAb-R) binding to overlapping epitopes were investigated. Precipitation of mAb-G solutions was most prominent at high ionic strength conditions and demonstrated strong dependence on ionic strength, as well as slight dependence on solution pH. At similar conditions no precipitation was observed for mAb-R solutions. Intermolecular interactions (interaction parameter, kD) related well with high concentration solubility behavior of both antibodies. Upon increasing buffer ionic strength, interactions of mAb-R tended to weaken, while those of mAb-G became more attractive. To investigate the role of amino acid sequence on precipitation behavior, mutants were designed by substituting the CDR of mAb-R into the mAb-G framework (GM-1) or deleting two hydrophobic residues in the CDR of mAb-G (GM-2). No precipitation was observed at high ionic strength for either mutant. The molecular interactions of mutants were similar in magnitude to those of mAb-R. The results suggest that presence of hydrophobic groups in the CDR of mAb-G may be responsible for compromising its solubility at high ionic strength conditions since deleting these residues mitigated the solubility issue.

Filling of High-Concentration Monoclonal Antibody Formulations into Pre-filled Syringes: Investigating Formulation-Nozzle Interactions To Minimize Nozzle Clogging.

Syringe filling of high-concentration/viscosity monoclonal antibody formulations is a complex process that is not fully understood. This study, which builds on a previous investigation that used a bench-top syringe filling unit to examine formulation drying at the filling nozzle tip and subsequent nozzle clogging, further explores the impact of formulation-nozzle material interactions on formulation drying and nozzle clogging. Syringe-filling nozzles made of glass, stainless steel, or plastic (polypropylene, silicone, and Teflon®), which represent a full range of materials with hydrophilic and hydrophobic properties as quantified by contact angle measurements, were used to fill liquids of different viscosity, including a high-concentration monoclonal antibody formulation. Compared with hydrophilic nozzles, hydrophobic nozzles offered two unique features that discouraged formulation drying and nozzle clogging: (1) the liquid formulation is more likely to be withdrawn into the hydrophobic nozzle under the same suck-back conditions, and (2) the residual liquid film left on the nozzle wall when using high suck-back settings settles to form a liquid plug away from the hydrophobic nozzle tip. Making the tip of the nozzle hydrophobic (silicone-coating on glass and Teflon-coating stainless steel) could achieve the same suck-back performance as plastic nozzles. This study demonstrated that using hydrophobic nozzles are most effective in reducing the risk of nozzle clogging by drying of high-concentration monoclonal antibody formulation during extended nozzle idle time in a large-scale filling facility and environment. Syringe filling is a well-established manufacturing process and has been implemented by numerous contract manufacturing organizations and biopharmaceutical companies. However, its technical details and associated critical process parameters are rarely published. Information on high-concentration/viscosity formulation filling is particularly lacking. This study is the continuation of a previous investigation with a focus on understanding the impact of nozzle material on the suck-back function of liquid formulations. The findings identified the most critical parameter-nozzle material hydrophobicity-in alleviating formulation drying at the nozzle tip and eventually limiting the occurrence of nozzle clogging during the filling process. The outcomes of this study will benefit scientists and engineers who develop pre-filled syringe products by providing a better understanding of high-concentration formulation filling principles and challenges.

Manufacturing of High-Concentration Monoclonal Antibody Formulations via Spray Drying-the Road to Manufacturing Scale.

Spray-dried monoclonal antibody (mAb) powders may offer applications more versatile than the freeze-dried cake, including preparing high-concentration formulations for subcutaneous administration. Published studies on this topic, however, are generally scarce. This study evaluates a pilot-scale spray dryer against a laboratory-scale dryer to spray-dry multiple mAbs in consideration of scale-up, impact on mAb stability, and feasibility of a high-concentration preparation. Under similar conditions, both dryers produced powders of similar properties-for example, water content, particle size and morphology, and mAb stability profile-despite a 4-fold faster output by the pilot-scale unit. All formulations containing arginine salt or a combination of arginine salt and trehalose were able to be spray-dried with high powder collection efficiency (>95%), but yield was adversely affected in formulations with high trehalose content due to powder sticking to the drying chamber. Spray-drying production output was dictated by the size of the dryer operated at an optimal liquid feed rate. Spray-dried powders could be reconstituted to high-viscosity liquids, >300 cP, substantially beyond what an ultrafiltration process can achieve. The molar ratio of trehalose to mAb needed to be reduced to 50:1 in consideration of isotonicity of the formulation with mAb concentration at 250 mg/mL. Even with this low level of sugar protection, long-term stability of spray-dried formulations remained superior to their liquid counterparts based on size variant and potency data. This study offers a commercially viable spray-drying process for biological bulk storage and an option for high-concentration mAb manufacturing. This study evaluates a pilot-scale spray dryer against a laboratory-scale dryer to spray-dry multiple monoclonal antibodies (mAbs) from the perspective of scale-up, impact on mAb stability, and feasibility of a high-concentration preparation. The data demonstrated that there is no process limitation in solution viscosity when high-concentration mAb formulations are prepared from spray-dried powder reconstitution compared with concentration via the conventional ultrafiltration process. This study offers a commercially viable spray-drying process for biological bulk storage and a high-concentration mAb manufacturing option for subcutaneous administration. The outcomes of this study will benefit scientists and engineers who develop high-concentration mAb products by providing a viable manufacturing alternative.

Filling of High-Concentration Monoclonal Antibody Formulations into Pre-Filled Syringes: Filling Parameter Investigation and Optimization

Syringe filling, especially the filling of high-concentration/viscosity monoclonal antibody formulations, is a complex process that has not been widely published in literature. This study sought to increase the body of knowledge for syringe filling by analyzing and optimizing the filling process from the perspective of a fluid's physical properties (e.g., viscosity, concentration, surface tension). A bench-top filling unit, comprising a peristaltic pump unit and a filling nozzle integrated with a linear actuator, was utilized; glass nozzles were employed to visualize liquid flow inside the nozzle with a high-speed camera. The desired outcome of process optimization was to establish a clean filling cycle (e.g., absence of splashes, bubbles, and foaming during filling and absence of dripping from the fill nozzle post-fill) and minimize the risk of nozzle clogging during nozzle idle time due to formulation drying at or near the nozzle tip. The key process variables were determined to be nozzle size, airflow around the nozzle tip, pump suck-back (SB)/reversing, fluid viscosity, and protein concentration, while pump velocity, acceleration, and fluid/nozzle interphase properties were determined to be relatively weak parameters. The SB parameter played an especially critical role in nozzle clogging. This study shows that an appropriate combination of optimal SB setting, nozzle size, and airflow conditions could effectively extend nozzle idle time in a large-scale filling facility and environment. Syringe filling can be considered a well-established manufacturing process and has been implemented by numerous contract manufacturing organizations and biopharmaceutical companies. However, its technical details and associated critical process parameters are rarely published. The information on high-concentration/viscosity formulation filling is particularly lacking. The purpose of this study is three-fold: (1) to reveal design details of a bench-top syringe filling unit; (2) to identify and optimize critical process parameters; (3) to apply the learning to practical filling operation. The outcomes of this study will benefit scientists and engineers who develop pre-filled syringe products by providing a better understanding of HC formulation filling principles and challenges.