Three-phase Grid-connected Inverter Research Articles

Advanced Discrete Control of Three-Phase Grid-Connected Inverter Using Improved Dead-Beat Compensator

Advanced Discrete Control of Three-Phase Grid-Connected Inverter Using Improved Dead-Beat Compensator

Expanded virtual vector-based model forecastable control strategy for three-phase two-level inverters

Abstract A three-phase, two-level inverter based on model forecastable control has good transient performance but poor steady-state performance. Considering the limitation of a limited number of discrete voltage vectors in a two-level inverter topology, this paper proposes a virtual vector model prediction method based on the analysis of a time-stepped forecasting model for a three-phase grid-connected inverter. First, three fixed virtual voltage vectors are constructed in each sector, and the action time of the required fundamental vector is found. Then, the cost function is constructed, and the optimum is selected among the virtual and fundamental voltage vectors in each sector. Finally, a hardware-in-the-loop experiment was carried out based on the PE-Expert4 experimental platform developed by Myway Co., LTD. The results show that the proposed virtual vector model forecastable control strategy can effectively improve the transient and steady-state performance of three-phase two-level inverters.

Design and implementation of an improved adaptive embedded-factor current controller for three-phase grid-connected inverter

This paper presents an improved current controller based on a series proportional integral resonant structure in synchronous reference frame in order to address low-order harmonics issue of the injected-grid current for three-phase grid-connected inverter. Additionally, to improve dynamic performance, an adapted factor is embedded into the proposed controller structure. Moreover, to design the parameters of the proposed controller, different constraint conditions are investigated. Based on the proposed controller structure and parameters design method, satisfactory steady-state and faster dynamic performances are both obtained in comparison to those of the conventional parallel proportional integral resonant controller. What's more, the proposed controller is easy to implement in practice. Simulation and experimental results are finally given to verify the effectiveness and superiority of the proposed controller.

Performance enhancement of a three-phase grid-connected PV inverter system using fractional-order integral sliding mode controls

Grid-integrated photovoltaic (PV) systems hold significant promise for sustainable energy production. However, these systems often struggle with maintaining energy quality and stability in the face of fluctuating conditions. To address these challenges, this study proposes the use of fractional-order integral sliding mode control (FO-ISMC) for grid-connected PV systems. The system comprises solar panel arrays, a DC/DC boost converter with its controller, and a three-phase inverter integrated into the utility grid. The primary goals of this study are to maximize power extraction from the PV system and to regulate system currents, thereby improving effectiveness and power quality. The proposed method is further refined using the particle swarm optimization (PSO) algorithm to fine-tune parameter settings. By optimizing the command gains of the FOI-SMC, the PSO algorithm enhances system performance and stability. Leveraging fractional-order and integral terms provides the control signal with additional degrees of freedom, enhancing system performance in the presence of internal and external disturbances. Simulation results demonstrate the effectiveness of the proposed controller compared to the classical controller, where in the case of Irradiation taking the value of 500 W/m2, the proposed strategy reduced the values of constant voltage, active power, and reactive power by percentages estimated at 88.18%, 90%, and 70%, respectively, compared to the traditional strategy. Also, the overshoot value of active power was reduced in all completed cases compared to the traditional strategy by percentages estimated at 53.57%, 66.66%, and 65%, respectively. The proposed strategy reduced the response time of reactive power in all cases compared to the traditional strategy by percentages estimated at 58.59%, 28.80%, and 75%, respectively. These ratios show the high performance of the proposed control in improving the characteristics of the studied system compared to traditional control based on PI control.

An Islanding Detection Method Based on the Reactive Power Disturbance for Multiple Inverter-Based DG Systems

In this paper, an islanding detection method for multiple inverter-based distributed generation systems is proposed, which is based on perturbing reactive power output. An asymmetric form of positive and negative reactive power disturbance is presented so that there always exists a certain total amount of disturbance in the system. To decrease the disturbance amplitude without expanding the non-detection zone, a positive feedback of frequency difference is added to the disturbance. A reactive power disturbance synchronization method without communication among inverters is proposed so that the averaging effect caused by unsynchronized reactive disturbances can be eliminated and the island can be detected in a multiple-DG system. Additionally, the islanding detection criterion is improved by establishing the relationship between the direction of disturbance and the numerical symbol of frequency difference, so there is no misjudgment of islanding detection in a weak grid. Finally, an experimental platform consisting of three 6kW three-phase grid-connected inverters and a 99.9kVA islanding detection test device is established. The experimental and simulation results indicate that the proposed method performs fast and precise islanding detection for the multiple-DG system with small NDZ and little impact on power quality. Additionally, no misjudgment happens in a weak grid.

Design and implementation of grid tied high step-up DC-DC converter with switched capacitor

In this paper, the design and implementation of a three-phase grid-connected inverter coupled with a high step-up DC-DC converter with a switched capacitor is demonstrated. In this converter two capacitors are utilized with a coupled inductor. The charging of capacitors takes place parallel and discharging in series during switch off and switch on time respectively. The energization of the coupled inductor provides the high voltage gain. The passive clamp circuit is used to recycle the leakage energy of the inductor circuit. Therefore, the switch stress is reduced. This high gain converter is given DC input of 40 V and a high voltage 538 V obtained is supplied to the grid connected inverter which uses sinusoidal pulse width modulation (SPWM), to obtain 3phase line-neutral voltage of 415 V from inverter for grid synchronization. A high voltage gain of 13 and efficiency of 96% is obtained for different load and voltage variation. The modeling and the simulation are done using physical security information management (PSIM) software and all the results are presented in this paper.

Aliasing Suppression Method for a Three-Phase Grid-Connected Photovoltaic Inverter Based on Multi-Sampling and Mean Filtering

In order to reduce the sampling delay and improve bandwidth, sability margin, and the robustness of the active damping in LCL-filtered grid-connected inverters, real-time sampling provides a convenient method. However, aliasing is easily introduced in the control loop because of high-frequency switching harmonics, resulting in a rise in low-order harmonics. To address the challenge of aliasing under real-time sampling, a new method based on multisampling and mean filtering is proposed by combining the proposed harmonic detection and control methods in this paper. This method works by sampling and controlling the fundamental current and selective subharmonic currents separately. The fundamental current control loop without any additional filters maintains real-time sampling, while multisampling and mean filters are applied to the harmonic current control loop. The proposed control method can not only improve the dynamic response performance and control stability of the system but also effectively suppress the selective low-order current harmonics and the aliasing of sampling. Finally, the correctness of the proposed sampling scheme and control strategy is verified by the simulation based on R2018b, MathWorks, Natick, MA, USA and an experimental prototype of a three-phase grid-connected photovoltaic inverter rated at 230 V/50 Hz/40 kW.

Current limiting algorithm for three-phase grid-connected inverters

Current limiting algorithm for three-phase grid-connected inverters

Modeling and Stability Analysis of the Three-phase Grid-connected Inverter Under DSOGI-PLL Considering Frequency-Adaptive Feedback

Modeling and Stability Analysis of the Three-phase Grid-connected Inverter Under DSOGI-PLL Considering Frequency-Adaptive Feedback

A Reconstructed Singular Return Ratio Matrix for Optimizing Design of the PLL in Grid-Connected Inverters

Phase-locked loop (PLL) is essential for the grid-connected inverter to ensure grid synchronization. Since the PLL introduces an negative-resistive admittance to be in parallel with the original inverter output admittance, it poses an instability risk for the grid-connected inverter under weak grid. The system stability can be evaluated by the return ratio matrix, which is the ratio of the inverter output admittance to the grid admittance. Due to the non-singular and non-diagonal properties of this matrix, its eigenvalues are irrational functions, leading to inconvenience of stability analysis and PLL parameters design. To address this issue, this paper reconstructs the return ratio matrix to make it singular. Thus, the eigenvalues become simpler, including a zero eigenvalue and a non-zero eigenvalue. Based on the non-zero eigenvalue, the relation between the gain margin and the PLL parameters is established, and an optimizing design method of the PLL parameters is proposed to achieve system stability and satisfactory PLL dynamic response. Finally, experimental results from a 10-kVA prototype of three-phase grid-connected inverter are provided to verify the validity of the proposed design method.

An Eigendecomposition-based dynamic characteristics design method of three-phase grid-connected inverters with considering reliability

Power converters often suffer the disturbance from input source or load during operation. The disturbance could cause large overshoot and harmful oscillation and even make the power converter break down. In order to ensure the reliability of the converter, it is necessary to accurate design the dynamic characteristics of a power converter, namely, the settling time and the overshoot. However, there is no quantitative dynamic characteristics design method of power converters so far. In this paper, an eigendecomposition-based (ED) dynamic characteristics design method is firstly proposed for the quantitative dynamic characteristics design of power converters and is employed into a three-phase grid-connected inverter. Then, the control-parameter regions of the three-phase inverter that satisfy the indexes of the settling time and the overshoot are obtained by using the proposed ED dynamic characteristic design method. Finally, the effectiveness and correctness of the proposed ED dynamic characteristics design method is verified by circuit simulation. Therefore, this paper provides an accurate and quantitative dynamic characteristic design method for power converters, which is helpful to improve the reliability of power converters.

Resonance suppression and quality improvement control strategy for a three-phase grid-connected voltage-source inverter under weak grid conditions

The three-phase voltage-source grid-connected inverters suffer from grid-connected current quality problems due to system resonance caused by the under-damping characteristics of the filter and grid impedance, on the one hand, and the grid-connected current distortion caused by the high content of low harmonics in the grid voltage, on the other hand. To resolve this problem, a current quality improvement control strategy, combining capacitor-current feedforward active damping and harmonic virtual impedance reshaping, is proposed by analyzing the mechanisms of system resonance and grid-connected current distortion. In addition, the proposed control strategy allows determining the virtual impedance parameters by using the root locus method, so as to achieve the purpose of improving the output grid-connected current quality of the three-phase voltage-source grid-connected inverter under weak grid conditions. Finally, the correctness and effectiveness of the proposed control strategy are verified by simulation and experiment.

VSG Control for Cascaded Three-Phase Bridge Based Battery Inverter

With the increasing number of new energy sources connected to the grid, the unbalanced output of three-phase grid-connected inverters and the lack of no inertia and damping characteristics in the traditional microgrid control system will seriously affect the stability of voltage, frequency, and power angle for microgrids. This paper proposes a novel cascaded three-phase bridge inverter topology for the battery system used for the electric vehicle. Compared with traditional cascaded H-bridge inverters, the proposed multilevel inverter can achieve self-adaptive balance for three phases. The mathematical model of a cascaded three-phase bridge inverter is established in this paper. Based on the voltage and current equations of a multilevel inverter, a new modulation strategy named carrier phase-shifted-distributed pulse width modulation (CPSD-PWM) was developed, which is more suitable for cascaded three-phase bridge inverters. The harmonic analytic equations of carrier phase-shifted pulse width modulation (CPS-PWM) and CPSD-PWM are constructed by the double Fourier analysis method. Compared with the traditional PWM modulation strategy, the CPSD-PWM can reduce the output harmonics and improve the balance of the three-phase output, which can realize the three-phase adaptive balance in the cascaded three-phase bridge inverter. This paper develops a cascaded three-phase bridge multilevel power converter system based on the virtual synchronous generator (VSG) control strategy. The voltage and frequency of inverter output can be accurately controlled in both island mode and grid-connected mode through active power-frequency regulation and reactive power–voltage regulation, and the stability of primary frequency regulation for the multilevel microgrid inverter can be improved by collaborative optimization of virtual inertia and virtual damping. The CPSD-PWM modulation strategy and VSG control strategy are verified by the simulation results and experimental data for the cascaded three-phase bridge inverter.

Two-coordinate decomposed SISO models-based stability analysis of three-phase grid-connected inverter systems with asymmetric control

In this paper, the Single-Input Single-Output (SISO) theory-based stability analysis method for weak grids with a three-phase grid-connected inverter (GCI) incorporating asymmetrical control is proposed in dq-frame and sequence domain, respectively. Initially, the paper presents two-coordinate decomposed models for Multi-input Multi-output (MIMO) systems. These models reveal that the stability of the MIMO system can be evaluated by analyzing two open-loop gains in the dq-frame or a single gain in the sequence domain using Nyquist/Bode plots. Next, the proposed analytical method is compared with existing state-of-the-art techniques. Theoretical analysis demonstrates that the proposed method enables the separate design of asymmetrical control in the d-axis and q-axis using the dq-frame approach. Furthermore, it enables the identification of the system's instability axes, namely the d-axis and q-axis. On the other hand, the proposed method in the sequence domain offers a lower computational complexity while accurately identifying the system's frequency-coupled resonances. Finally, the effectiveness of the proposed method is validated through simulations and experiments, consolidating its practical applicability.

Ancillary Services of a Grid-Connected Inverter with Overcurrent Protection Capability under Voltage Sag

The Distributed Generator of a Photovoltaic System (DGPVS) is an essential factor for future power plant generation, and it can be created by connecting multiple small power plant generators in a microgrid system. This paper focuses on the overcurrent protection of a three-phase grid-connected inverter (3P-GCI) under voltage sag conditions in sustaining connection loss between the 3P-GCI and the primary grid, which involves voltage instability. The ancillary service shows more advantage in overcurrent protection during voltage sags, which limits the generated current under sag duration. Its service can protect the inverter and avoid more disturbances to the primary grid because the 3P-GCI remains connected. Proposed LVRT strategy with limit current feature play the role to protect 3P-GCI under voltage sag. In the normal grid, the 3P-GCI can inject 302W of active power with a power factor (PF) equal to one. 1.4% of VTHD and 4.3% of ITHD shows the performance of the proposed system. Meanwhile, the 3P-GCI injects 239VAr reactive power and reduces injected active power to 135W which is essential to remain connected to the primary grid during voltage sags and limit the generated current. The validation results show that this prototype successfully compensates for the grid voltage drops by injecting 239Var of reactive power and limiting its generated current to 1.592A.

A Method Based on NGO-HKELM for the Autonomous Diagnosis of Semiconductor Power Switch Open-Circuit Faults in Three-Phase Grid-Connected Photovoltaic Inverters

With accelerating grid decarbonization and technological breakthroughs, grid-connected photovoltaic (PV) systems are continuously connected to distribution networks at all voltage levels. As the grid interaction interfaces between PV panels and the distribution network, PV inverters must operate flawlessly to avoid energy and financial losses. As the failure of semiconductor switches is the leading cause of abnormal operation of PV inverters and typically cannot be detected by internal protection circuits, this paper aims to develop a method for the autonomous diagnosis of semiconductor power switch open-circuit faults in three-phase grid-connected PV inverters. In this study, a ReliefF-mRMR-based multi-domain feature selection method is designed to ensure the completeness of the fault characteristics. An NGO-HKELM-based classification method is proposed to guarantee the desired balance between generalization and exploration capability. The proposed method overcomes the common problems of poor training efficiency and imbalances between generalization and exploration capabilities. The performance of the proposed method is verified with the detection of switch OC faults in a three-phase H-bridge inverter and neutral-point-clamped inverter, with diagnostic accuracy of 100% and 99.46% respectively.

A d-axis current error compensation method based on coupling mechanism for Grid-Connected inverters under weak grid

Three-phase grid-connected inverters (GCI) are widely used in wind farms as they serve as the interface between the renewable energy system and the grid. However, the sub-synchronous resonance (SSR) issues have been observed between GCI and weak grid, which seriously threatens the stable operation of grid-connected system. In this paper, the coupling mechanism between the GCI and the weak grid is analyzed from the perspective of power angle relationship. Revealing that there is a small signal coupling between d-axis current and power angle due to the grid impedance introduced by weak grid, which further destabilizes the studied system through PLL feedforward paths. It provides an explanation for the limitations of short circuit ratio (SCR) and phase-locked loop (PLL) bandwidth. Then, a d-axis current error compensation method employed in current control is proposed to damp SSR. The method introduces an extra parallel branch to compensate the PLL feedforward effect and increases the qd-axis impedance amplitude of GCI to decrease the coupling degree between the GCI and weak grid simultaneously. By employing the proposed compensation method, the SSR issues of the GCI under weak grid can be effectively solved under grid impedance fluctuations and high PLL bandwidth. Finally, the experimental results verify the correctness of the theoretical analysis and the effectiveness of the proposed compensation method.© 2017 Elsevier Inc. All rights reserved.

A DPWM-Based Quasi-Constant Switching Frequency Control for Full ZVS Range Three-Phase Inverter With Reactive Power Transfer Capability

In this paper, a quasi-constant switching frequency zero voltage switching (ZVS) control strategy is proposed for three-phase grid-connected inverters. Full ZVS range can be achieved for all the switches at any load, modulation index, and power factor using discontinuous pulse width modulation (DPWM). No additional high- frequency sensor or auxiliary circuit is needed. The switching frequency is constant at steady-state. It does not change with the phase angle or the power factor, but it varies with the modulation index, grid RMS voltage and current. The frequency can be easily calculated in a digital controller based on current ripple prediction (CRP) instead of current zero-crossing detection (ZCD). The turn-on loss is eliminated so the inverter can operate at a high switching frequency, especially by using wide band-gap devices. The conversion efficiency, power density, cost, and dynamic response of the inverter can all be improved. A 3.3 kVA experimental prototype using SiC MOSFETs interfacing 400 V DC link with three-phase 110 V AC grid is developed to verify the effectiveness of the proposed control strategy.

A phase compensation method combined with power correction for suppressing sub-synchronous resonance of wind generation under weak grid

Since three-phase grid-connected inverters (GCI) play a crucial role as the connection between renewable energy systems and the grid. They are extensively used in wind farms. However, issues related to sub-synchronous resonance (SSR) have been observed in wind farms, which pose a significant threat to the safe and stable operation of large-capacity wind farms and the grid. In this paper, the mechanism and characteristics of the SSR occurring in the GCI system under weak grid are analyzed based on the impedance model. And derives that the origin affecting the stability of the system is the asynchrony of system frames and control frames. Then, a phase compensation method employed in phase-locked loop (PLL) is proposed to suppress SSR, which can introduce a compensation frame to reduce the angle difference with the system frame. The grid strength can be enhanced equivalently. Meanwhile, virtual resistance and virtual reactance will also be introduced through the introduction of reactive power. It will further provide damping to the system, but will limit power transfer capability. Thus, the power needs to be corrected to achieve precise power control by change the value of current reference. By employing the proposed method, the SSR issues of the GCI under weak grid can be effectively solved and achieve precise power control. Finally, the experimental results verify the correctness of the theoretical analysis and the effectiveness of the proposed method

A Generic Multicell Network Control for Three-Phase Grid-Connected Inverters

The inherent resonance of <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">LCL</i> filters threatens the inverter stability seriously. Moreover, the strong <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"><tex-math notation="LaTeX">$dq$</tex-math></inline-formula> -axis cross-coupling of <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">LCL</i> -filtered grid-connected inverters in a synchronous frame goes against the independent regulation of active ( <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"><tex-math notation="LaTeX">$P$</tex-math></inline-formula> ) and reactive ( <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"><tex-math notation="LaTeX">$Q$</tex-math></inline-formula> ) power that is required in various applications. Besides, the imbalance and harmonics of the grid voltage will deteriorate the injected grid current, so the disturbance suppression performance of grid-connected inverters is important. Furthermore, excellent steady-state and dynamic performance is essential for grid-connected inverters. To solve the above four issues simultaneously, a complex-domain model of grid-connected inverters is established, and a generic multicell network control (GMNC) structure is proposed in this article. Based on the proposed GMNC structure, a number of control schemes are obtained, and the quantitative relationship between inverter performance and control parameters can be given directly and precisely for each scheme. Therefore, it is convenient and simple for engineers to select proper control schemes depending on the practical conditions and to design all the control parameters for an expected steady-state, dynamic, and antidisturbance performance without the resonance and the coupling issues. Finally, the effectiveness of the proposed control is verified by the experiments.