Gas Isotope Research Articles

Effect of Mechanical Damage on Tritium Permeability Resistance of FeAl/Al2O3 Coating on 316L Stainless Steel.

Depositing a tritium permeation barrier on the surface of materials is a key method for reducing tritium permeability. During actual operational processes, the surface of the tritium permeation barrier may experience mechanical damage, such as spalling and scratches. The hydrogen permeability resistance of the coating will degrade due to such forms of mechanical damage. It is a significant engineering challenge to evaluate the impact of these damages on the coating's tritium resistance. In this experiment, the mechanical damage to the FeAl/Al2O3 tritium permeation barrier on 316L stainless steel was simulated through scratching, debonding, and thermal shock. Subsequently, a hydrogen isotope gas drive permeation (GDP) test was conducted. The influence of the degree of mechanical damage on the coating's tritium permeation behavior was assessed and discussed. The results indicate that, under the same damage mechanism, the coating's tritium permeability resistance is positively correlated with the integrity of the coating. Additionally, the impact of scratches on the coating surface is more severe than that of other damage mechanisms.

Noble gases in shocked igneous rocks from the 380 Ma-old Siljan impact structure (Sweden): A search for paleo-atmospheric signatures

Finding direct records of the ancient Earth's atmosphere is key to understand the evolution of the entire planet. Nevertheless, such records are scarce, and only a few geological samples with preserved paleo-atmospheric signatures are available today. In this study, we analyzed noble gases contained in shocked granitic and volcanic rocks collected across the 380 Ma-old Siljan impact structure (in Sweden) to investigate the potential of shocked quartz crystals with planar deformation features (PDFs), often decorated by fluid inclusions, to preserve atmospheric signatures.Our results reveal that most of the investigated samples show relative elemental abundances of noble gases falling between those of air and meteoric water values. Atmospheric gases are present in the samples but excesses in radiogenic, nucleogenic, and fissiogenic noble gas isotopes highlight interactions of fluids with crustal rocks during the impact-generated hydrothermal circulation of fluids after the impact. Such fluid circulation event(s) could also have remobilized older fluids originally present in fluid inclusions preserved in the mineral lattices. Furthermore, results obtained on the two pure quartz fractions highlight a stronger atmospheric signature correlated with the presence of PDFs. The atmospheric component detected in this study could represent either a paleo-atmospheric signature trapped shortly after the Siljan impact event, or it may result from modern atmospheric contamination. Future studies of noble gases contained within shocked quartz crystals from other impact structures will unveil if such samples present advantages compared to other paleo-atmospheric proxies.

Brominated flame retardant in animal feeds from Poland

The safety of food of animal origin is closely related to feed quality. Feed pollution by brominated flame retardants (BFRs) leads to the exposure of animals and consumers of food of animal origin to these substances. The study aimed to assess the concentration of ten PBDE (BDE-28, 47, 49, 99, 100, 138, 153, 154, 183, and 209) congeners and eight nBFRs (TBX, PBT, HBB, PBEB, EH-TBB, BTBPE, BEH-TBPH, and DBDPE) in 59 feed and feed materials from six different feed categories (277/2012/EU). The quantification of analytes was based on isotopic dilution and gas chromatography–high-resolution mass spectrometry (GC-HRMS). All 59 feed samples were contaminated with at least one of the analytes. PBDEs and nBFRs were found in 78% and 91% of the samples, respectively. BFR content ranged from 0.18 to 5.87 μg·kg-1 in feed with a 12% moisture content, and the most contaminated category was vegetable oils, followed by fishmeal, feeds for fish, animal fats, and compound feeds for pigs. The least contaminated samples turned out to be compound feeds for chickens. This study confirms the general trend of decreasing PBDE concentrations in fishmeal. In the investigated samples, BDE-47 and BDE-209 contributed the most to the ∑PBDE content. DBDPE, HBB, and PBT contributed the most to the investigated ∑nBFRs. The widespread occurrence of nBFRs in feed seems disturbing because these compounds have replaced PBDEs. Their concentrations in the feed may most likely exceed those of PBDEs in the coming years.

The Arpu Kuilpu meteorite: In‐depth characterization of an H5 chondrite delivered from a Jupiter Family Comet orbit

AbstractOver the Nullarbor Plain in South Australia, the Desert Fireball Network detected a fireball on the night of June 1, 2019 (7:30 pm local time), and 6 weeks later recovered a single meteorite (42 g) named Arpu Kuilpu. This meteorite was then distributed to a consortium of collaborating institutions to be measured and analyzed by a number of methodologies including SEM‐EDS, EPMA, ICP‐MS, gamma‐ray spectrometry, ideal gas pycnometry, magnetic susceptibility measurement, μCT, optical microscopy, and accelerator and noble gas mass spectrometry techniques. These analyses revealed that Arpu Kuilpu is an unbrecciated H5 ordinary chondrite, with minimal weathering (W0‐1) and minimal shock (S2). The olivine and pyroxene mineral compositions (in mole%) are Fa: 19.2 ± 0.2 and Fs: 16.8 ± 0.2, further supporting the H5 type and class. The measured oxygen isotopes are also consistent with an H chondrite (δ17O‰ = 2.904 ± 0.177; δ18O‰ = 4.163 ± 0.336; Δ17O‰ = 0.740 ± 0.002). Ideal gas pycnometry measured bulk and grain densities of 3.66 ± 0.02 and 3.77 ± 0.02 g cm−3, respectively, yielding a porosity of 3.0% ± 0.7. The magnetic susceptibility of this meteorite is log χ = 5.16 ± 0.08. The most recent impact‐related heating event experienced by Arpu Kuilpu was measured by 40Ar/39Ar chronology to be 4467 ± 16 Ma, while the cosmic ray exposure age is estimated to be between 6 and 8 Ma. The noble gas isotopes, radionuclides, and fireball observations all indicate that Arpu Kuilpu's meteoroid was quite small (maximum radius of 10 cm, though more likely between 1 and 5 cm). Although this meteorite is a rather ordinary ordinary chondrite, its prior orbit resembled that of a Jupiter Family Comet (JFC) further lending support to the assertion that many cm‐ to m‐sized objects on JFC orbits are asteroidal rather than cometary in origin.

The effect of irradiation for Nafion membrane electrode rapid separation of hydrogen-methane by electrochemical hydrogen pumps

Designing an efficient and reliable tritium plant has become a major challenge to developing nuclear fusion, which focuses on efficient and safe hydrogen isotope separation and purification. The electrochemical hydrogen pump (EHP) developed in recent years can be used to separate and compress hydrogen. Herein, we used the commercial Nafion membrane electrode in the EHP, which has excellent H2/CH4 separation performance. When the cell voltage is at 0.8 V, the current density is 2.04 A/cm2, the hydrogen separation rate can reach 14.2 mL/ (min ·cm2), and the hydrogen purity is more than 99.99 %. The damage mechanism of electron beam irradiation on the membrane electrode was revealed. It was found that irradiation caused Nafion’s main chain and branch chain to break, producing hydroxyl and carboxyl functional groups. The degree of chain fracture increased with the radiation dose, perforation and cracks occurred in the proton exchange membrane (PEM). Under the electron beam irradiation dose of 10 kGy, the membrane electrode can still maintain excellent H2/CH4 separation performance, and the hydrogen permeability caused by cracks and perforations is at a very low level. This study reveals the change of macroscopic performance caused by the microscopic mechanism of membrane electrode irradiation damage, provides a promising way to separate hydrogen isotope gases and is expected to promote the development of tritium plants in fusion engineering.

Modified cryogenic distillation for tritium enrichment in the tritium accountancy system of helium cooled ceramic breeding test blanket system

Given the prevalence of scenarios involving low-abundance and large-volume hydrogen isotope batch separation in the tritium extraction and enrichment for fusion reactors, as well as the deuterization of tritiated water in nuclear power plants or fusion reactors, it is imperative to develop a more efficient enrichment and separation process to meet this demand. Consequently, this paper proposes a “quasi-continuous distillation” coupled with batch distillation for the batch enrichment and separation of low-tritium-concentrated hydrogen isotope gases, involved in the tritium accountancy system (TAS) of Helium-Cooled Ceramic Breeding blanket (HCCB-TBS), as an input. The design of this separation process addressed a feed with a tritium concentration of 18 ppm and approximately 5.8 Nm3 of hydrogen isotope gas. The feasibility of this separation process was successfully verified through tritium verification experiment.

Geochemical Characteristics and Origin of Natural Gas in the Middle of Shuntuoguole Low Uplift, Tarim Basin: Evidence from Natural Gas Composition and Isotopes

Multiple types of reservoirs, including volatile oil reservoirs, condensate gas reservoirs, and dry gas reservoirs, have been discovered in ultra-deep layers buried at depths greater than 7500 m. Understanding the genetic types of natural gas is of utmost importance in evaluating oil and gas exploration potential. The cumulative proved reserves of the super deep layer in the Shuntuoguole low uplift area of the Tarim Basin exceed 1 × 108 t (oil equivalent). The origin, source, and accumulation characteristics of natural gas still remain a subject of controversy. By analyzing the composition and carbon isotope of natural gas, a detailed investigation was conducted to examine the unique geochemical and reservoir formation characteristics of the Ordovician ultra-deep natural gas within different fault zones in the middle region of the Shuntuoguole low uplift. It was determined that most of the natural gas in this area is displaying a characteristic of wet gas with a drying coefficient ranging from 0.41 to 0.99. The carbon isotope composition of methane in the gas reservoir shows relatively light values, ranging from −49.4‰ to −42‰. The carbon and hydrogen isotopes of the components are distributed in a positive order. The natural gas is oil type gas, which is derived from marine sapropelic organic matter and has a good correspondence with the lower Yuertusi formation. The maturity of natural gas in Shunbei No. 1 and No. 5 fault zones is about 1.0%, which is the associated gas of normal crude oil, while the maturity of No. 4 and No. 8 fault zones is higher than 1.0%, which is the mixture of kerogen pyrolysis gas and crude oil pyrolysis gas. The variations in the drying coefficient and carbon isotope composition of the natural gas provide evidence for the migration patterns within the Shuntuoguole low uplift central region. It indicates that the Shunbei No. 5 and No. 8 fault zones have likely migrated from south to north, while the No. 4 fault zone has migrated from the middle to both the north and south sides. These migration patterns are primarily controlled by high and steep strike-slip faults, which facilitate the vertical migration of natural gas along fault planes. Consequently, the gas accumulates in fractured and vuggy reservoirs within the Ordovician formation.

The helium and carbon isotopic signature of Ocean island basalts: Insights from Fogo volcano (Cape Verde archipelago)

Fluid inclusions (FI) entrapped in phenocrysts carried by Ocean Island Basalts (OIB) contain key information on volatiles’ abundance and origin in their mantle sources. Here, we add new piece of knowledge to our understanding of volatile geochemistry in global OIB magmas, by presenting new noble gas (He-Ne-Ar) and carbon (C) isotope results for olivine- and clinopyroxene-hosted FI from enclaves, lavas, tephra and volcanic gas samples from Fogo, the only frequently active volcano at the Cape Verde archipelago (eastern Atlantic Ocean). FI, together with crater fumaroles, constrain the Fogo 3He/4He signature at 7.14–8.44 Rc/Ra (where RC is the air-corrected 3He/4He isotope ratio, and Ra is the same ratio in air), which is within the typical MORB (Mid-Ocean Ridge Basalt) mantle. The carbon isotopic ratio (δ13C vs. Pee Dee Belemnite) of CO2 in FI and fumaroles range from -6.04 to -4.41 ‰. We identify systematic variations of δ13C and He/Ar* with FI entrapment pressure (estimated from a combination of host mineral barometry and FI microthermometry), from which we develop a model for volatile degassing in the mantle-to-crustal magma storage system. The model predicts a crustal-like signature for carbon (δ13C of -0.4 ± 1.0 ‰) in primary melts formed by mantle melting at ∼2200 MPa (∼77 km) and a source He/Ar* ratio of 0.90–0.24, which are indicative of variably depleted mantle metasomatized by carbon enriched melts/fluids from a crustal component. We also use our results to characterise regional (in the Cape Verde and Canary archipelagos) and global trends in C and He isotope composition from OIB. From a comparison with the few other OIB localities for which δ13C are available, we propose that a carbon enriched crustal component could be recurrent at a global scale in OIB magmatism, although often masked by isotope fractionation during magmatic degassing. We additionally find that, at regional scale, He isotopes in OIB scale inversely correlate with the degree of partial melting of the mantle beneath individual islands’ (inferred from the La/Yb ratio of erupted basalts). More widely, our results corroborate previously established global relationships between OIB He isotopic signature, plume buoyancy flux and overlying plate velocity. In this interpretation, the MORB-like 3He/4He (8 ± 1 Ra) at Fogo reflects a combination of (i) low to medium magma productivity, (ii) relatively low plume buoyancy flux (∼1.1 Mg/s), and (iii) slow average velocity (∼3 cm/yr) of the overlying plate.

End-Member Mixing Model for Methane Carbon Isotope Fractionation During Shale Gas Desorption and Its Application.

Unlike conventional natural gas reservoirs, shale gas development involves systematic changes in methane carbon isotopes that cannot be effectively described by existing isotope fractionation models and mechanisms. Therefore, based on fundamental theories such as Rayleigh fractionation, mass transfer flow, and mass conservation, this study established isotopic fractionation equations for methane in adsorbed and free gas. By considering adsorbed and free gases as two end-members and using an isotope mixing model, a fractionation model for methane carbon isotopes during shale gas desorption was constructed. This model quantifies the isotopic fractionation effects during shale gas desorption and elucidates the mechanism of methane carbon isotope fractionation. Using on-site desorbed gas content and isotope data, parameter fitting and model calculations were conducted to characterize methane carbon isotope variations throughout the process of shale core field desorption. The results show a pattern of "initially negative and then turning positive," consistent with those of physical simulation experiments. It was clarified that differences in mixing the two end-members and isotopic fractionation play key roles in the variation of methane carbon isotopic composition in shale gas. By applying the methane carbon isotope fractionation model, the contribution of adsorbed gas during shale gas production was explored. It was found that in the early stage of development, the adsorbed gas in Well JY 1 was negligible. After nearly seven years of development, the contribution of adsorbed gas in the later stage has only reached nearly 15%, indicating that the production contribution of adsorbed gas is still less than 0.3 million cubic feet per day. The open flow of Well JY 6-2 is more conducive to the production of adsorbed gas, but the production capacity is still mainly contributed by free gas, indicating that the shale gas production capacity in the later stage in the Jiaoshiba gas field is still primarily dominated by free gas.

The generation mechanism of deep natural gas in Tabei uplift, Tarim Basin, Northwest China: insights from instantaneous and accumulative effects

The natural gas heavy carbon isotope and high dryness coefficients genesis in Tabei uplift, Tarim Basin has been highly controversial. To investigate the generation mechanisms of natural gas in the Tabei Uplift. Natural gas chemical composition, carbon isotopes were used to analyze the genesis of natural gas, source rock maturity, and basin modeling were conducted to reconstruct the natural gas generation process, and the influences of instantaneous and cumulative effects on natural gas properties was discussed. The results show that the dryness coefficients of natural gas range from 0.62 to 0.99 (average: 0.92), the methane contents range from 30.42% to 96.4% (average: 85.10%), ethane contents from 0.43% to 15.58% (average: 3.39%), propane contents from 0.11% to 11.43% (average: 1.78%), and the methane carbon isotopes range from −47.30‰ to −33.80‰ (average: −36.96‰), ethane carbon isotopes range from −39.60‰ to −33.20‰ (average: −35.57‰), propane carbon isotopes range from −36.90‰ to −28.50‰ (average: −35.49‰). Compared with the actual regional thermal evolution of the source rock (Ro% range from 1.4%∼1.7%), the natural gas exhibits excessively high dryness coefficients and heavy methane carbon isotope characteristics. The natural gas is primary cracking gas and sourced from marine type II kerogen. The dryness coefficient, methane carbon isotopes, and source rock maturity gradually increases from the west to the east. Instantaneous effects and leakage led to the dry gas and relative heavy methane carbon isotopes generated at a low maturity level. The current natural gas in the Ordovician reservoirs was all generated during the Himalayan orogeny. Long period pause of the gas generation between the two hydrocarbon generation phases is the main cause for the instantaneous effects.

Formaldehyde and the transient receptor potential ankyrin-1 contribute to electronic cigarette aerosol-induced endothelial dysfunction in mice.

Electronic nicotine delivery systems (ENDS) aerosol exposures can induce endothelial dysfunction (ED) in healthy young humans and animals. Thermal degradation of ENDS solvents, propylene glycol, and vegetable glycerin (PG: VG), generates abundant formaldehyde (FA) and other carbonyls. Because FA can activate the transient receptor potential ankyrin-1 (TRPA1) sensor, we hypothesized that FA in ENDS aerosols provokes TRPA1-mediated changes that include ED and "respiratory braking"-biomarkers of harm. To test this, wild-type (WT) and TRPA1-null mice were exposed by inhalation to either filtered air, PG: VG-derived aerosol, or FA (5 ppm). Short-term exposures to PG: VG and FA-induced ED in female WT but not in female TRPA1-null mice. Moreover, acute exposures to PG: VG and FA stimulated respiratory braking in WT but not in TRPA1-null female mice. Urinary metabolites of FA (ie, N-1,3-thiazolidine-4-carboxylic acid, TCA; N-1,3-thiazolidine-4-carbonyl glycine, TCG) and monoamines were measured by LC-MS/MS. PG: VG and FA exposures significantly increased urinary excretion of both TCA and TCG in both WT and TRPA1-null mice. To confirm that inhaled FA directly contributed to urinary TCA, mice were exposed to isotopic 13C-FA gas (1 ppm, 6 h). 13C-FA exposure significantly increased the urine level of 13C-TCA in the early collection (0 to 3 h) supporting a direct relationship between inhaled FA and TCA. Collectively, these data suggest that ENDS use may increase CVD risk dependent on FA, TRPA1, and catecholamines, yet independently of either nicotine or flavorants. This study supports that levels of FA in ENDS-derived aerosols should be lowered to mitigate CVD risk in people who use ENDS.

Gas isotope geochemistry of Tangquan hot spring system in Nanjing (China)

Tangquan hot springs is one of the three well-known geothermal systems in Nanjing, Jiangsu Province, eastern China. Previous studies have shown its high flow rate and ideal water chemistry favorable for utilization. Here we further examine the potential of the hot springs using gas geochemistry in this paper. 35 water samples and 16 gas samples were collected for chemical isotopic analyses. The geothermal gases are found to be primarily atmospheric in origin, containing high nitrogen, oxygen and carbon dioxide gases. Carbon isotope shows that the origin of CO2 and CH4 are thermal metamorphic in the upper crust. The isotope ratio of helium is 3.47–4.73 Ra, indicating that mantle He accounts for 44–60% in total of geothermal gases. These findings furnish the grounds to infer geothermal potential at the deeper part of the geothermal system. The immediate geothermal reservoir has a temperature of 90 °C, but the temperature of deeper part of the system could reach 150–205 °C, using the carbon gas isotope geothermometer. These findings show a promising future of deep geothermal resources in the region.

Eutrophication driven macrophyte-derived organic matter decomposition to methane emission relates to co-metabolism effect in freshwater sediments

Lakes and wetlands play pivotal roles in global organic matter storage, receiving significant inputs of organic material. However, the co-metabolic processes governing the decomposition of these organic materials and their impact on greenhouse gas emissions remain inadequately understood. This study aims to assess the effects of mixed decomposition involving macrophytes and cyanobacteria on carbon emissions. A series of microcosms was established to investigate the decomposition of macrophyte residues and algae over a period of 216 days. A two-component kinetic model was utilized to estimate methane (CH4) production rates. Gas isotope technology was employed to discern the contributions of CH4 produced by macrophyte residues or algae. Quantitative PCR and analysis of 16S rRNA gene amplicons were employed to assess changes in functional genes and microbial communities. There were significant differences in the cumulative carbon release from the decomposition of different plant types due to the addition of carbon sources. After adding algae, the cumulative emission of CH4 increased significantly. The δ13C–CH4 partitioning indicated that CH4 originated exclusively from the fresh organic carbon of macrophyte residues, while it shifted to algae source after adding algae. The synergistic effect of the mixed decomposition on the CH4 emissions was greater than the sum of the individual decompositions. The microbial community richness was higher in the single plant residue treatment compared to the mixed treatment with algae addition, while microbial evenness in the sediment increased steadily in each treatment. Our findings emphasize the pronounced co-metabolic effect observed during the mixed decomposition of macrophytes and cyanobacteria.

Coupling noble gas and alkane gas isotopes to constrain normally pressured shale gas expulsion in SE Sichuan Basin, China

Coupling noble gas and alkane gas isotopes to constrain normally pressured shale gas expulsion in SE Sichuan Basin, China

Constraining the evolutionary stages of a hypogene karst system by combining morphological, geochemical and geochronological data - the example of carbonate breccia-hosted Melnička Peštera

A combination of morphological observations, geochemical data from calcite minerals and geochronology by burial age dating and U-series is used to constrain the geological and geomorphological setting and the evolutionary stages of a hypogene karst system. This methodological suit is applied to Melnička Peštera, a horizontal cave developed in carbonate breccia overlying dolomite marble in Melnica locality (N. Macedonia), where hydrothermal karst development occurred in both dolomite and calcite marble. The passage morphology of the cave, having a reverse triangle, Laughöhle cross-sections, suggests development near the water table by slowly moving waters. Calcite crusts are found throughout the cave, and based on their relationship to passage morphology, appear to pre-date main horizontal passage formation. Their carbonate stable and clumped isotope and fluid inclusion noble gas compositions indicate cooling of the hydrothermal system with an increased contribution of shallower groundwater. U-series data suggests Early Pleistocene deposition of the calcite crusts. Water table notches and convectional features carved into breccia bedrock and calcite crusts point to subsequent development at and above the water table by condensation corrosion. The solutional aggressiveness near the water table was likely related to CO2, that previously degassed from the deeper parts of the system where calcite was depositing, and redissolved in the cooler, shallower waters. Due to poor connection with the surface, the cave air above the water table likely had high pCO2, that further helped to maintain aggressiveness of the groundwater at the water-air contact, and boosted condensation corrosion above it, preventing deposition of related secondary calcite minerals. The cave-hosting carbonate breccia deposited as an alluvial fan filling up a paleovalley cut into Upper Miocene sediments. Cosmogenic nuclide burial age dating of quartz fragments confirms Early Pliocene age for the breccia, and constrains the paleovalley incision to Late Miocene, likely related to base level lowering caused by the Messinian Salinity Crisis.

Review article: Melt-affected ice cores for polar research in a warming world

Abstract. Melting polar and alpine ice sheets in response to global warming pose ecological and societal risks but will also hamper our ability to reconstruct past climate and atmospheric composition across the globe. Since polar ice caps are crucial environmental archives but highly sensitive to ongoing climate warming, the Arctic and Antarctic research community is increasingly faced with melt-affected ice cores, which are already common in alpine settings of the lower latitudes. Here, we review the characteristics and effects of near-surface melting on ice-core records, focusing on a polar readership and making recommendations for melt-prone study regions. This review first covers melt layer formation, identification and quantification of melt, and structural characteristics of melt features. Subsequently, it discusses effects of melting on records of chemical impurities, i.e. major ions, trace elements, black carbon, and organic species as well as stable water isotopic signatures, gas records, and applications of melt layers as environmental proxies. Melting occurs during positive surface energy balance events, which are shaped by global to local meteorological forcing, regional orography, glacier surface conditions and subsurface characteristics. Meltwater flow ranges from homogeneous wetting to spatially heterogeneous preferential flow paths and is determined by temperature, thermal conductivity and stratigraphy of the snowpack. Melt layers and lenses are the most common consequent features in ice cores and are usually recorded manually or using line scanning. Chemical ice-core proxy records of water-soluble species are generally less preserved than insoluble particles such as black carbon or mineral dust due to their strong elution behaviour during percolation. However, high solubility in ice as observed for ions like F−, Cl−, NH4+ or ultra-trace elements can counteract the high mobility of these species due to burial in the ice interior. Stable water isotope records like δ18O are often preserved but appear smoothed if significant amounts of meltwater are involved. Melt-affected ice cores are further faced with questions about the permeability of the firn column for gas movement, and gas concentrations can be increased through dissolution and in situ production. Noble gas ratios can be useful tools for identifying melt-affected profile sections in deep ice. Despite challenges for ice-core climate reconstruction based on chemical records, melt layers are a proxy of warm temperatures above freezing, which is most sensitive in the dry snow and percolation zone. Bringing together insights from snow physics, firn hydrology, and ice-core proxy research, we aim to foster a more comprehensive understanding of ice cores as climate and environmental archives, provide a reference on how to approach melt-affected records, and raise awareness of the limitations and potential of melt layers in ice cores.

Fluid origin and evolution of the Taolin Pb-Zn deposit in northeastern Hunan Province, South China: Insights from fluid inclusions and H-O-He-Ar isotopes

Situated in northeastern Hunan Province, the vein-type Pb-Zn orebodies at Taolin are mainly hosted in NE-/NEE-trending faults between Dayunshan-Mufushan pluton and Neoproterozoic metasedimentary rocks of the Lengjiaxi Group. Hydrothermal mineralization can be divided into five stages: (1) coarse-grained quartz stage, (2) quartz-fluorite-base metal stage, (3) quartz-barite-fluorite-base metal stage, (4) pale pink and colorless quartz stage, and (5) fine-grained quartz stage. In this research, fluid inclusions as well as stable (H-O) and noble gas (He-Ar) isotope compositions were performed to uncover the nature, origin, and evolution of the ore-forming fluids, ore precipitation mechanisms, and mineralization process of the Taolin deposit. Four types of fluid inclusions, i.e., liquid-rich two-phase inclusions (LV-type), pure liquid phase inclusions (PL-type), vapor-rich two-phase inclusions (VL-type), and pure vapor phase inclusions (PV-type), were distinguished in sphalerite, quartz, and fluorite. Microthermometric analysis of fluid inclusion assemblages in sphalerite, quartz, and fluorite from different stages indicates that from the Stage 1 to Stage 5, the homogenization temperatures vary between 168 and 211 °C, between 151 and 198 °C, between 131 and 180 °C, between 132 and 164 °C, and between 118 and 138 °C, respectively, whereas the fluid salinities vary from 12.4 to 16.9 wt% NaCl equivalent, from 9.7 to 14.6 wt% NaCl equivalent, from 5.6 to 10.3 wt% NaCl equivalent, from 3.6 to 9.7 wt% NaCl equivalent, and from 0.9 to 3.8 wt% NaCl equivalent, respectively. The H-O isotope data of quartz and the He-Ar isotopic compositions of sulfide crystals suggest that the ore-forming fluids were a mixture of crust-derived magmatic hydrothermal fluid and meteoric water. Fluid mixing and cooling were likely the crucial mechanisms for ore precipitation.

Role of hypogenesis in the evolution of karst in the Taurus Mountains Range, Turkey

Field observations and laboratory data collected from the Taurus Mountains Range, Turkey during the last two decades provided evidence for the link between the evolution of hypogene karst and the geodynamic history. Major evidence includes; carbonate-hosted secondary ore deposits that are converted from primarily hypogene minerals by epigene, oxygen-rich groundwater circulating at local to intermediate depths. Another piece of evidence of hypogene karst in the Tauride is the Kırkgöz springs’ huge submerged cave/conduit system, which formed the Antalya Travertine Plateau, which is the world’s largest deposit precipitated by cool karst groundwater. The obruks in central Tauride are giant collapse dolines formed by ascending hypogene fluids in the upper continental crust, rich in volcanogenic carbondioxide. The groundwater’s noble gas and carbon isotope data are helpful in determining the existing but asymptomatic hypogene activity in the upper crust. Hypogene karst development seems common in parts of the world with current or past geodynamic activity. However, a hydrogeological overview of the geodynamic history is essential to assess the hypogene processes and their reflections on the land surface.

Source, Migration Pathways, and Atmospheric Release of Geologic Methane Associated With the Complex Permafrost Regimes of the Outer Mackenzie River Delta, Northwest Territories, Canada

AbstractSources and fluxes of methane to the atmosphere from permafrost are significant but poorly constrained in global climate models. We present data collected from the variable permafrost setting of the outer Mackenzie River Delta, including observations of aquatic methane seepage, core determinations of in situ methane occurrence and seep gas isotope geochemistry. The sources and locations of in situ geologic methane occurrence and aquatic and atmospheric gas release appear to be controlled by the regional geology and permafrost conditions. Where permafrost is >250 m thick, thermogenic gas deposits at depth are isolated by laterally continuous, low permeability ice‐bearing sediments with few through‐going thawed taliks. Thus, the observed in situ methane and aquatic gas seepage appears to be dominated by microbial methane. In contrast, where permafrost is <80 m thick, taliks are more likely to be through‐going, providing permeable conduits from depth and migration pathways for both thermogenic and biogenic gas. Continuous annual fluid sampling of two lakes and a river channel documents aquatic methane flux from microbial sources, more deeply buried thermogenic sources, and mixtures of both. Using estimates of in situ methane concentration from deep core samples and observations of in situ free gas occurrences, we conclude that the reservoir of in situ geologic methane within ice bonded permafrost is substantial and that this methane is presently migrating with ongoing atmospheric release. It is our assessment that the permafrost setting, and processes described are sensitive to future climate change as the permafrost warms.

Stable and Radio-Isotopic tools to understand the groundwater recharge and dynamics of CHASHMA-Mianwali area, Pakistan

The study conducted on “Chashma-Mianwali” area to investigate the impact of canals, lake and rivers flowing through the area on groundwater recharge and dynamics of the area. Isotopic and noble gases data suggested localize impacts of canals, lake and river on groundwater recharge. Groundwater residence time using Tracer Lump Parameter Model (LPM), and Chloroflourocarbons (CFCs) data suggest a very young water in the range of 14–59 years. The real and filtration velocities of groundwater were found to be 22.2 cm/day and 10.94 cm/day, respectively, in south-west direction and in-situ effective porosity of the aquifer was 49.3 %. The hydraulic conductivity of the aquifer was estimated with average value of 143 m/day with Transmissivity (T) of 43,127 m2/day.