Gas Exposure Research Articles

Effect of ozone gas exposure on drain current of solution-processed IGZO-TFT

The drain current (ID) of indium gallium zinc oxide thin-film transistors (IGZO-TFTs), fabricated by spin coating, decreases even when they are exposed to ozone gas at a concentration equal to or lower than 5 ppm. The ID reduction rate increases when the film thickness and the firing temperature in the spin-coating process of IGZO layer decreases. In these samples, the peak intensity ratio of the O 1s X-ray photoelectron spectroscopy (XPS) peak due to the OH group and the intensity of the infrared (IR) absorption band at 3000 cm−1–3500 cm−1 due to the OH stretching vibration increase. This indicates that OH groups within the IGZO film contribute to the ozone reaction mechanism. These findings are significant for developing high-sensitivity ozone sensors using a simpler process.

Emergency evacuation risk assessment for toxic gas attacks in airport terminals: Model, algorithm, and application

Transportation infrastructure has often been the target of terrorist attacks, and mitigation of the risk of toxic gas attacks is a challenging task in the design of indoor emergency evacuation systems. Considering multiple emergency response modes, we propose an agent-based risk assessment model and its algorithm to integrate gas diffusion and pedestrian movement data for emergency response, quickly assessing average individual exposure risk. We assessed the exposure status of individuals with respect to their emergency response actions following a toxic gas attack in an airport terminal. The results indicate that in the event of a general gas attack on an airport terminal, ventilation must be immediately ceased along with early evacuation. In areas with a shelter-in-place environment, the ventilation mode and shelter-in-place time should be determined based on the concentration of indoor and outdoor gases. In areas with nerve gas exposure and high population density, a new exit must be established at evacuation bottlenecks, and pedestrians must be guided to evacuate while promptly closing ventilation. These results offer suggestions and strategies for emergency response and decision-making in airport terminals during such incidents.

Surface treatment optimization of mixed cellulose ester membrane by cold plasma treatment to improve apple juice clarification

This study aimed to determine the optimal conditions for the surface modification of mixed cellulose ester (MCE) microfiltration membrane by cold plasma (CP) for apple juice clarification. Response surface method using central cubic design (CCD) was employed for the optimization of the membrane surface modification process. Plasma gas type (oxygen, carbon dioxide, and air), power (10, 15, and 20 W), and exposure time (120, 180, and 240 s) were used as the factors for cold plasma surface modification. The results revealed the surface modification of the MCE membrane using air as plasma gas with plasma power and exposure time equal to 10 W and 180 s resulted in the maximum permeate flux in apple juice clarification. The results of scanning electron microscope, and atomic force microscope confirm the effect of CP treatment on the membrane surface roughness. Fourier transform infrared spectroscopy showed the incorporation of the hydroxyl group into the membrane surface due to CP treatment which affected the surface contact angle and hydrophilicity. The CP treatment of the membrane significantly affects the membrane resistances. Also, the surface modification of the MCE membrane using the CP treatment process in optimal conditions is an effective method for clarifying apple juice.

“En bloc” combined 270-degree keratolimbal allograft with central lamellar keratoplasty for severe limbal stem cell deficiency secondary to mustard gas exposure

BackgroundSevere limbal stem cell deficiency (LSCD) resulting from chronic and delayed-onset mustard gas keratopathy (MGK) presents substantial management challenges. This article introduces an “en bloc” surgical procedure combining a 270-degree keratolimbal allograft (KLAL) with central lamellar keratoplasty (CLK) as a novel approach to treat this condition. MethodsA retrospective case series was conducted at Labbafinejad Medical Center in Tehran, Iran, from 2002 to 2019, including 13 eyes from 13 male patients diagnosed with chronic and delayed-onset MGK. Each patient underwent the combined 270-degree KLAL and central LK procedure. A 270-degree peritomy, sparing the superior quadrant, was performed. A lamellar dissection using a crescent blade and a blunt Melles dissector was carried out, extending 2 mm from the limbus. Fresh donor tissue with intact 270-degree limbo-conjunctiva, obtained from a whole globe, was prepared to match the recipient bed and sutured into place. Postoperative outcomes and success including ocular surface integrity, graft longevity, and best-corrected visual acuity (BCVA), were evaluated. ResultsThe average follow-up period was 87.6 ± 49.8 months. Surgical success was achieved in 12 of 13 patients (92.3 %). Preoperative BCVA improved from 1.07 ± 0.24 (approximately 20/250) logMAR to 0.63 ± 0.30 (approximately 20/80) logMAR postoperatively. One patient experienced immune rejection of the KLAL graft, while two patients had episodes of corneal rejection, all successfully managed with aggressive immunosuppressive therapy. ConclusionsThe “en bloc KLAL + CLK” procedure demonstrates promising long-term outcomes in managing chronic and delayed-onset MGK associated with severe LSCD. This approach offers advantages, including reduced surgical complexity, minimized antigenic load, and better anatomical alignment, leading to successful ocular surface restoration and improved visual acuity.

Single ZnO Nanowire for Electrical and Optical NO2 Gas Sensing: Origin of Reversible and Irreversible Gas Effects Investigated by Photoluminescence Spectroscopy.

In this work, the gas sensing properties of a single ZnO nanowire (NW) are investigated, simultaneously in terms of photoluminescence (PL) and photocurrent (PC) response to NO2 gas, with the purpose of giving new insights on the gas sensing mechanism of a single 1D ZnO nanostructure. A single ZnO NW sensing device was fabricated, characterized, and compared with a sample made of bundles of ZnO NWs. UV near-band-edge PL emission spectroscopy was carried out at room temperature and by lowering the temperature down to 77 K, which allows detection of resolved PL peaks related to different excitonic transition regions. Surface effects were observed in PL maps, considering different nano and microstructures. Electrical and optical measurements were acquired at the same time during the NO2 gas exposure, allowing for the comparison of PL and PC response times and signal recovery. During NO2 gas desorption, irreversible behavior in the surface-related and donor-acceptor pair (DAP) regions is interpreted as the effect of an initial transient when electronic transfer from the gas molecules to the bulk occurs through the ZnO NW surface which acts as a channel. To the best of our knowledge, this is the first work which investigates the simultaneous PL optical and PC electrical response signals of a single ZnO NW to gas exposure.

Doping engineering modulated adsorption and sensing performance of β-tellurene towards greenhouse gas molecules

Abstract CO2, CH4, CF4, CCl3F, CCl2F2, HCF2Cl, N2O and SF6 are well-known greenhouse gases that cause serious threat to the earth's ecological environment. To expand the application and development of two-dimensional (2D) materials in the field of greenhouse gas sensing, adsorption of the greenhouse gases on the pristine β-tellurene monolayer was investigated by first-principles calculations to estimate the potential application of β-tellurene as a monitor for greenhouse gas. The results indicate that β-tellurene exhibits favorable adsorption capabilities for greenhouse gases, especially demonstrating selective sensing potential for SF6 molecules due to the changes in electronic structures after gas exposure. The effects of noble metal atoms doping on structural, electronic and SF6 sensing properties were systematic estimated. The calculation results revealed that doping with different transition metal (TM) atom could bring diverse electronic properties to β-tellurene. Among them, doping with Os, Pd, Pt, Rh, and Ru could effectively enhance the electronic delocalization, improving the detection sensitivity for β-tellurene. In addition, TM doping could also improve the recovery time of β-tellurene by two orders of magnitude, and provided the possibility for β-tellurene as a work function type sensing material. By delving into the gas sensing properties of β-tellurene with TM doping, we provided a valuable guidance for the design of innovative tellurene- based sensing 2D materials for devices and technologies.

Oxygen plasma-modified polycaprolactone nanofiber membrane activates the biological function in cell adhesion, proliferation, and migration through the phosphorylation of FAK and ERK1/2, enhancing bone regeneration

Bone defects present significant clinical challenges in orthopedics, orthodontics, and maxillofacial surgeries. Accelerated bone regeneration can be facilitated by incorporating mesenchymal stem cells, but limitations in cell survival and growth remain concerns for complete bone repair. Biomaterial-based membranes have been developed to form biocompatible, degradable, and mechanically stable barriers in guided bone regeneration processes. Polycaprolactone (PCL) is a biodegradable polymer widely used as a bone regenerative material because of its favorable mechanical properties. However, its inherent hydrophobicity limits cell adhesion and proliferation, which are necessary for effective bone regeneration. To address this, we fabricated cell-regulatory PCL nanofiber membranes using plasma treatment to enhance induced pluripotent stem cell-derived mesenchymal stem cells and osteoblast growth. The plasma treatment parameters (gas type, flow rate, power, and exposure time) were optimized to enhance PCL’s surface hydrophilicity and protein adsorption properties while maintaining its mechanical integrity. The optimized oxygen plasma-modified PCL membrane demonstrated notable improvements in cell viability, adhesion, and proliferation. In addition, there was improved migration, regulated by cell surface markers and signaling proteins, of the induced pluripotent stem cell-derived mesenchymal stem cells and osteoblasts. In vivo studies in a rat calvarial defect model showed that the plasma-modified PCL membrane dramatically improved new bone formation, facilitating bone regeneration. These findings highlight the potential of plasma treatment of PCL nanofibers to produce effective cell-regulatory membranes for bone defect reconstruction.

Emulsion Stability and Rheological Properties of Emulsions Prepared with Ozonized Hazelnut Oil

In this study, physical and rheological characteristics of the emulsion stabilized with whey protein isolate (WPI) at a concentration of 0.25% (w/w) and containing ozone applicated hazelnut oil (OHO) were studied. The hazelnut oil was subjected to ozone gas exposure for durations of 1, 5, 30, 60, 180, and 360 min. The emulsions made with both control (HO) and OHO were analysed to assess emulsion properties. It was observed that as the duration of ozone application increased, the emulsion activity index (EAI) experienced a decrease. Specifically, ozone applications of 30, 60, and 180 min significantly reduced emulsion stability index (ESI). The creaming ratio of emulsions formulated with OHO for durations of 1, 5, 30, 60, and 180 min were found to be 23%, 20%, 18%, 16%, and 44%, respectively. Optical microscopy revealed that significant flocculated droplet formed in emulsions including OHO. The longer time the ozone application resulted that the emulsions exhibited more solid-like behaviour. Furthermore, differential scanning calorimeter (DSC) was utilized to assess the changes in the melting and cooling profiles of hazelnut oil after being applicated with ozone. An increase in ozone application duration led to the melting peaks broadening and shifting towards lower temperatures. Also, ozone application caused that the sharp exothermic crystallization shifted towards lower temperatures and become broader and less pronounced as the duration of the application increased.

EVALUATION OF EFFICIENCY OF OIL DISPLACEMENT BY WATER AND GAS AT VARIOUS MODES

The purpose of the work is to analyze in detail the efficiency of oil displacement by various agents, such as water and gas, at different modes. During the study, various methods and technologies aimed at increasing oil recovery were considered, and the effect of various parameters on the efficiency of the process was studied.Particular attention was paid to the method of water-gas impact (HBV) using pump-ejector systems (PES), which provides a triple impact on oil formations by simultaneous or alternate injection of water and gas.Theoretical and experimental methods were used to conduct the study. The beginning of the work was the study and analysis of scientific sources on the issue of assessing the effectiveness of oil displacement. Further, laboratory tests were carried out to assess the effectiveness of oil displacement by various agents. Experimental studies were carried out on a two-phase and three-phase filtration unit. The main parameter measured was the coefficient of oil displacement by water and separation gas. The effectiveness of the impact of various modes of water and gas exposure was studied: alternating (cyclic) injection of water and gas with different cyclicity, simultaneous injection of water and gas, as well as injection of a fine water and gas mixture.Based on the results of the work, it was concluded that the degree of influence of wetting processes on the final displacement result is a critical factor. The following main points can be distinguished:- final value of oil displacement coefficient depends on selection of displacement agent;- in case of water and gas impact, the sequence of water and gas injection is of great importance;- the efficiency of oil displacement is highly dependent on the absolute permeability of the reservoir, as well as on the injection mode (sequential, simultaneous, cyclic).The results of the experiments can be useful for predicting the development of oil fields and choosing optimal methods for increasing oil recovery.The uniqueness of this article lies in the study of the possibilities of using multithreaded ejectors to increase the efficiency of hydrocarbon production.

Characterization of Wear Patterns in Gun Barrel’s Throat Region Using Forensic Microscope: Insights Into Long-Term Effects of High-Pressure Gas Exposure

Objectives: This research aims to explore the damage sustained by the gun barrel's throat region over a long period of use, shedding light on the wear characteristics, and providing valuable insights into the long-term effects of high-pressure gas exposure during firing. Methods: To achieve this objective, the appearance of the gun barrel's throat region was characterized using forensic microscopy techniques. Visual and microscopic examinations were conducted on five (5) gun barrels with ten years or less of service usage and five (5) gun barrels with over ten years of service usage from the Philippine National Police to assess the degree of wear in the barrel’s throat region. Findings: The findings revealed varying degrees of wear in the barrel throat regions. Firearms with 10 years or less of service usage exhibited moderate corrosion, narrow cracks, and minimal soot particle presence while firearms with over 10 years of service usage showed severe corrosion, deep cracks, scattered potholes, superficial scraped surfaces, and heavy soot particle presence. Novelty: This research contributes to the understanding of barrel performance, maintenance, and potential hazards associated with aging firearms, thus providing novel insights into the long-term effects of high-pressure gas exposure during firing. By examining the changes in material properties and surface roughness of the gun barrel’s throat region, this study seeks to improve the understanding of how repeated firing impacts gun barrel performance and longevity. This, in turn, may aid in developing future maintenance practices to enhance firearm durability and safety. Keywords: Gun Barrels, Wear Characteristics, Gun Barrel Throat Region, High-Pressure Gas Exposure, Wear Patterns

Trends in chlorine and chloramine gas exposures reported to United States poison centers

Introduction Chlorine and chloramine gas inhalation can occur when household cleaners are mixed. The increased emphasis on disinfecting practices during the COVID-19 pandemic may have contributed to an increase in chlorine and chloramine gas exposures in the United States, which has not been studied. Methods In a retrospective review, reported data on chlorine and chloramine gas exposures in the National Poison Data System were collected from January 1, 2015, to December 31, 2022. Data included demographics and exposure details, including location, dose, formulation, co-exposures, treatments, and outcomes. Demographic analyses and descriptive statistics were conducted. Results During the study period, 85,104 total exposures to chlorine and chloramine gas were reported, consisting of 79,281 isolated exposures and 5,823 co-exposures. Total exposures increased by 61% from 8,385 in 2015 to 13,503 in 2022, with the largest increase of 38.3% occurring from 2019 to 2020. Total exposures remained increased through 2022 with no return to pre-pandemic levels. Most exposures occurred in “own residence” (n = 72,213, 84.9%), with a larger proportion of exposures occurring at home peri-pandemic versus pre-pandemic (88.4% versus 81.7%). One percent (n = 1,030) of exposures were admitted to a non-critical care unit, 0.73% (n = 619) were admitted to a critical care unit, and 0.03% (n = 26) resulted in death. Discussion The onset of the COVID-19 pandemic and increased emphasis on cleaning practices were likely contributing factors to the marked increase in exposures in 2020, which persisted through 2022. Cleaning practices that developed during the beginning of the pandemic likely persisted despite returning to more normal daily routines, which may explain the ongoing increase in reported exposures. Most reported exposures were unintentional, mild in symptomatology, and required the use of non-invasive therapies, if any. Conclusions Future efforts should focus on public education on the safe use of cleaning products to prevent exposure to toxic chlorine and chloramine gases.

The pH-dependent properties of cuprous oxide thin films prepared by electrochemical deposition for liquid petroleum gas sensing

Efficient liquid petroleum gas sensing was investigated by modulating the pH level (8, 9, 10, 11, and 12) of electrochemically deposited nanostructured cuprous oxide thin films in a lactate bath. The synthesized films were characterized by surface contact angle, XRD, SEM, UV–Vis absorption, Mott-Schottky, and AC impedance spectroscopy measurements. These displayed a unique initial increment or decrease followed by a persistent decrement or increment at pH 9–10. This turning pH point exhibited the least wetting polycrystalline Cu2O growth with the smallest crystallite size of ∼ 45 nm, the highest dislocation density of ∼50 µm−2, and a strain of 0.03 according to X-ray diffraction. SEM micrographs identified ∼ 1 µm-sized, closely structured grains with trigonal-prismatic shapes. The Mott-Schottky plots drawn from C-V measurements revealed a significant dependence of flat band potential and free carrier density on the deposition bath pH level. Cu2O films deposited using the lactate bath changed the conductivity at pH 9 from n-type to p-type when increasing the pH value. With the conductivity transition, films prepared at pH 9 displayed a relatively high direct band gap energy of 2.28 eV. Liquid petroleum gas (LPG) sensing at 70 °C demonstrated the most substantial gas response of 11.5 % at pH 10 Cu2O films. Cu2O thin films deposited at pH 9 emerged as the most stable and reproducible p-Cu2O LPG sensor, with response and recovery times ranging from 20 to 25 seconds. Remarkable changes in the film structures and morphologies were revealed with pH values above 9 after the gas exposure. The grain shape and distribution of pH 9 remained unchanged, assuring the stability of the sensing platform.

Operando Investigation of WS2 Gas Sensors: Simultaneous Ambient Pressure X-ray Photoelectron Spectroscopy and Electrical Characterization in Unveiling Sensing Mechanisms during Toxic Gas Exposure.

Ambient pressure X-ray photoelectron spectroscopy (APXPS) is combined with simultaneous electrical measurements and supported by density functional theory calculations to investigate the sensing mechanism of tungsten disulfide (WS2)-based gas sensors in an operando dynamic experiment. This approach allows for the direct correlation between changes in the surface potential and the resistivity of the WS2 sensing active layer under realistic operating conditions. Focusing on the toxic gases NO2 and NH3, we concurrently demonstrate the distinct chemical interactions between oxidizing or reducing agents and the WS2 active layer and their effect on the sensor response. The experimental setup mimics standard electrical measurements on chemiresistors, exposing the sample to dry air and introducing the target gas analyte at different concentrations. This methodology applied to NH3 concentrations of 100, 230, and 760 and 14 ppm of NO2 establishes a benchmark for future APXPS studies on sensing devices, providing fast acquisition times and a 1:1 correlation between electrical response and spectroscopy data in operando conditions. Our findings contribute to a deeper understanding of the sensing mechanism in 2D transition metal dichalcogenides, paving the way for optimizing chemiresistor sensors for various industrial applications and wireless platforms with low energy consumption.

Selective and reversible carbon mono oxide gas detection using silver doped octahedral molecular sieves (OMS-2) nanorods

In this work a potable, resistive sensor is fabricated for the selective detection of CO gas using nanorods of Ag doped octahedral molecular sieves-2 (Ag-OMS-2). During exposure to carbon monoxide (CO) gas at room temperature, resistance of Ag-OMS-2 film was dropped from 557 kΩ to 352 kΩ in just 18 sec. However, exposed sample regained its initial resistance value in 25 sec when CO gas source was removed. Both sensing and recovery processes were carried out at room temperature. The sensor film showed excellent reproducibility during several cycles of CO gas exposure. Swift activation of oxygen molecules for the oxidation of CO by the silver present in the tunnel of manganese oxide network is supposed to be responsible for sensing activity of Ag-OMS-2 towards carbon monoxide gas.

Characterization of occupational inhalation exposures to particulate and gaseous straight and water-based metalworking fluids

Exposure assessments to metalworking fluids (MWF) is difficult considering the complex nature of MWF. This study describes a comprehensive exposure assessment to straight and water-based MWFs among workers from 20 workshops. Metal and organic carbon (OC) content in new and used MWF were determined. Full-shift air samples of inhalable particulate and gaseous fraction were collected and analysed gravimetrically and for metals, OC, and aldehydes. Exposure determinants were ascertained through observations and interviews with workers. Determinants associated with personal inhalable particulate and gaseous fractions were systematically identified using mixed models. Similar inhalable particle exposure was observed for straight and water-based MWFs (64–386 µg/m3). The gaseous fraction was the most important contributor to the total mass fraction for both straight (322–2362 µg/m3) and water-based MWFs (101–699 µg/m3). The aerosolized particles exhibited low metal content irrespective of the MWF type; however, notable concentrations were observed in the sumps potentially reaching hazardous concentrations. Job activity clusters were important determinants for both exposure to particulate and gaseous fractions from straight MWF. Current machine enclosures remain an efficient determinant to reduce particulate MWF but were inefficient for the gaseous fraction. Properly managed water-based MWF meaning no recycling and no contamination from hydraulic fluids minimizes gaseous exposure. Workshop temperature also influenced the mass fractions. These findings suggest that exposures may be improved with control measures that reduce the gaseous fraction and proper management of MWF.

Effects of Lithium Metal Storage Environment on Its Reactivity Toward Polyethylene Oxide-Based Blend Electrolytes

Lithium metal has generated significant interest as an anode material because of its high theoretical capacity (3860 mAh/g). However, issues such as dendrite growth and lithium loss during cycling make this material incompatible with current liquid electrolytes. Solid polymer electrolytes (SPE) have been proposed as a potential replacement as they are non-flammable, able to resist dendrite growth, have decent ionic conductivity and good interfacial contact with lithium metal.One aspect that is often overlooked is the fact that passivation layers, initially reported by Naudin et Al (1), often form on the lithium metal surface and are hence intrinsic to the chemical composition of the lithium surface (2, 3). According to Otto et Al (4), residual quantities of atmospheric gases are often present in lithium metal storage environments, thus electrode surface modification is inevitable. This passivation layer is expected to impact the reactivity of the lithium metal anode (LMA) towards SPE. Moreover, such phenomenon was originally described by Peled et Al as the solid electrolyte interface (SEI) (5). Lithium metal reactivity towards PEO, suspected by Galluzo et Al (6), was recently reported by Liu et Al (7), under optimized conditions (ultra-thin neat materials), but the impact of this phenomenon in a realistic LMA environment has not been extensively investigated.In this study, the impact of gas exposure on a LMA was investigated by exposing freshly cut lithium rods to O2, CO2 and N2. The resultant passivation layers were characterized via XPS. The effect of passivation layer formation on LMA reactivity towards SPE was measured by exposing samples with pre-characterized passivation layers to common SPE materials. The resultant interface was characterized using Raman spectroscopy. SPE-passivation layer reactivity was correlated to ageing properties by EIS and kinetic charge transfer characteristics in galvanostatic linear polarization at the LMA-SPE interface, in a symmetric Li – SPE – Li stack.This study revealed that the chemical composition of the lithium metal passivation layer affects its reactivity towards SPE as well as the electrochemical performance of a Li-SPE-Li symmetric cell. A thorough characterization of the lithium metal passivation layer is essential for the understanding of some of the fundamental factors affecting all solid-state lithium metal battery performance and is therefore consubstantial with the development of modified LMA. C. Naudin et al., Characterization of the lithium surface by infrared and Raman spectroscopies. Journal of Power Sources 124, 518-525 (2003).S.-K. Otto et al., In-Depth Characterization of Lithium-Metal Surfaces with XPS and ToF-SIMS: Toward Better Understanding of the Passivation Layer. Chemistry of Materials 33, 859-867 (2021).P. R. G. Zhuang, F. Kong, F. McLarnon The reaction of clean Li surfaces with small molecules in ultrahigh vacuum: II. Journal of The Electrochemical Society, 159-164 (1998).S.-K. Otto et al., Storage of Lithium Metal: The Role of the Native Passivation Layer for the Anode Interface Resistance in Solid State Batteries. ACS Applied Energy Materials 4, 12798-12807 (2021).E. Peled, Film forming reaction at the lithium/electrolyte interface. Journal of Power Sources 9, 253-266 (1983).M. D. Galluzzo et al., Dissolution of Lithium Metal in Poly(ethylene oxide). ACS Energy Letters 4, 903-907 (2019).P. Liu et al., Increasing Ionic Conductivity of Poly(ethylene oxide) by Reaction with Metallic Li. Advanced Energy and Sustainability Research 3, 2100142 (2022).

Development of a broad range of two-colour ozone indicator

The antiviral and antibacterial properties of ozone gas have been utilised for air and on-site disinfection. However, excess ozone gas exposure is toxic to humans, necessitating the monitoring of exposure levels. While this has been achieved using ozone indicators, determining exposure levels at intermediate time points during exposure remains challenging owing to the current ones being capable of measuring exposure only at endpoints. Shifts in the endpoint are also difficult as the coverage ranges of the indicators are dependent on a single colour dye. The indicator that covers a wide range is desirable to treat various pathogenic microorganisms. The aim of this study was to develop a two-colour ozone indicator with a broad coverage range that does not compromise the performance of the individual dyes. Exposure levels were indicated by visible changes in colour density and phase, aiding the measurement of exposure at the endpoints and during the exposure period, thereby maintaining better safety profiles for exposed individuals. Additionally, a theoretical approach for the development of two-colour indicators has been described.

Emerging detection of carbon-based gases with multiple bonds by activating Mo[dbnd]O bonding in Na, Sb-codoped NiMoO4

Exhausting carbon-based gases from building construction or comfortable household supplies have caused the main pollution gas species for the indoor air environment. Given the variety of indoor activities, many reports have been challenged to find room-temperature operational and harmless materials. Here, we report that the activating MoO vibration mode in Na,Sb doped-NiMoO4 micro-sized powder reveals the high response of CO and VOC, occupying multiple bonds at room temperature. We performed Na and Sb doping in the α-NiMoO4 crystal structure, such as introducing the Sb in Ni and interstitial doping of Na in around 4 Å of free space in the NiMoO4 crystal structure that manipulates the partial β-NiMoO4 phase. The Na,Sb-codoped NiMoO4 generates the higher MoO vibration mode from FT-IR measurement and enables carbon-based gas detection with 38 responses to CO and nearly 20 responses to VOC under 20 ppm of each analyte gases environment. Furthermore, the n-type gas sensing behavior of Na,Sb doped-NiMoO4 chemiresistor exhibits an immediate sensing response instead of a none-of response than intrinsic or single element doped NiMoO4. These results suggest that Na,Sb codoped-NiMoO4 is the applicable material for emergent warning against carbon-based gas exposure in the indoor environment. In addition, activating the electrochemical reaction site of MoO4–2 in NiMoO4 is tailorable by a simple doping process.

Green Ironmaking at Higher H2 Pressure: Reduction Kinetics and Microstructure Formation During Hydrogen-Based Direct Reduction of Hematite Pellets

Hydrogen-based direct reduction (HyDR) of iron ores has attracted immense attention and is considered a forerunner technology for sustainable ironmaking. It has a high potential to mitigate CO2 emissions in the steel industry, which accounts today for ~ 8–10% of all global CO2 emissions. Direct reduction produces highly porous sponge iron via natural-gas-based or gasified-coal-based reducing agents that contain hydrogen and organic molecules. Commercial technologies usually operate at elevated pressure, e.g., the MIDREX process at 2 bar and the HyL/Energiron process at 6–8 bar. However, the impact of H2 pressure on reduction kinetics and microstructure evolution of hematite pellets during hydrogen-based direct reduction has not been well understood. Here, we present a study about the influence of H2 pressure on the reduction kinetics of hematite pellets with pure H2 at 700 °C at various pressures, i.e., 1, 10, and 100 bar under static gas exposure, and 1.3 and 50 bar under dynamic gas exposure. The microstructure of the reduced pellets was characterized by combining X-ray diffraction and scanning electron microscopy equipped with electron backscatter diffraction. The results provide new insights into the critical role of H2 pressure in the hydrogen-based direct reduction process and establish a direction for future furnace design and process optimization.Graphical

Assessment of environmental radioactivity concentration and effective dose rates from radon gas exposure from water samples in Gezira State, Sudan

A study was conducted in Gezira State, Sudan, to estimate the concentration of radon and the annual effective dose rate in water samples based on inhalation, ingestion, and age group. The study collected 26 samples from different locations. The results showed that the mean concentration of radon was 7.68 ± 1.07 Bq.l−1, and the mean effective dose rate of radon released from water to indoor air was 19.17 ± 2.68 μSv.y−1. The average effective dose rates calculated from ingestion, inhalation, and the total annual effective dose rate were 18.81 ± 2.63, 19.34 ± 2.71, and 38.15 ± 5.34 μSv.y−1, respectively. The annual effective dose rates for infants, children, and adults were calculated to have mean values of 80.60 ± 11.27, 53.73 ± 7.51, and 38.38 ± 5.37 μSv.y−1, respectively. The study found that 23.1% of the samples exceeded the maximum contamination level, while 76.9% were below the reference levels set by the USEPA, WHO, and EU. Despite the increase in radiation dose with age and consumption rates, the radiation dose from water was lower than the recommended limits set by UNSCEAR and WHO. Additionally, the bronchial epithelium received twice the radiation dose compared to the stomach walls.