Fueled Compression Ignition Engine Research Articles

The Green Energy Effect on an HCCI Engine from Used Cooking Oil-based Biodiesel from Malaysia

Emissions from internal combustion engines (ICEs) significantly impact the environment, leading continents worldwide to work towards reducing them. The industry is increasingly leaning towards electric powertrains. However, power plants still utilize ICEs as generators, contributing to global pollution. Consequently, ICE emissions are garnering international attention. Alternatives like the Homogeneous Charge Compression Ignition (HCCI) engine and biodiesel fuels are being explored. HCCI engines have not been extensively tested with Used Cooking Oil (UCO) biodiesel. This study investigates the performance and emissions of HCCI engines using UCO-based biodiesel. This study tested an air-cooled, single-cylinder, 4-stroke diesel engine operating at 3600 rpm with a displacement of 0.219 liters. The HCCI mode was activated during preheating and run at 2700 rpm under varying biodiesel blend percentages and intake temperatures. In HCCI mode, brake-specific fuel consumption (BSFC) increased, peaking at a 90°C intake temperature. Diesel fuel in-cylinder pressure reached a maximum of 81 bars at 90°C, decreasing to 79 bars at 70°C. The HCCI mode resulted in lower NOx, CO, and UHC emissions. Higher biodiesel blend ratios further reduced CO emissions. Raising the intake air temperature to 90°C lowered NOx emissions by 96.66%, from 150 ppm to 5 ppm. Using green energy sources as fuel in HCCI engines significantly reduced emissions in this study, suggesting their potential as a future fuel for advanced engines.

Multi-objective optimization of a dual fuel CI engine powered with syngas and pilot diesel using TLBO algorithm: A metaheuristic approach

Abstract The thermochemical conversion of biomass into producer gas presents an attractive alternative fuel option for compression ignition (CI) engines, making biomass gasification a critical driver for achieving sustainable development goals. Considering the application of producer gas (PG) in CI engine, the most potential gases include H2 and CO as main fuel compounds and it is crucial to comprehensively understand the impact of these two gas components on the engine behaviour. Nowadays, artificial intelligence-powered models are frequently applied for simulating engines that run on a single type of fuel. However, their usage is not as common when it comes to modeling dual-fuel CI engines run on synthetic producer gas or syngas. The present study explores the feasibility of optimizing operational parameters, such as engine load and syngas composition, in improving the efficiency and lowering the levels of pollutants emitted by a 3.5 kW CI engine operated under dual fuel (DF) mode using syngas as primary fuel and diesel as pilot fuel. The performance and emission characteristics of syngas (H2:CO) is examined by studying its behaviour in four different combinations. The compositions of syngas are prepared based on the volumetric percentage of the H2 and CO and is inducted into the combustion chamber using a novel venturi-type air-gas mixer. In the present study, an intelligent metaheuristics-based optimization algorithm i.e., Teaching–Learning Based Optimization (TLBO) is developed and introduced, to develop a predictive model within constrained range of engine operating conditions. Further, the algorithm is used to estimate multiple engine performance characteristics simultaneously viz., brake thermal efficiency (BTE), unburned hydrocarbons (HC), and carbon monoxide (CO). The resultant findings identify the optimal engine load of 68.87% and the ideal syngas composition of 63.9% H2 and 49.5% CO as key parameters for maximizing engine efficiency while minimizing exhaust emission. At these optimized operating condition, 19.49% BTE is observed, while HC and CO emission was found to be 384.6 ppm and 445.33 ppm respectively. This shows the effective and efficiency of the proposed algorithm.

Experimental evaluation of a diesel engine using amide-functionalized carbon nanotubes as additives in commercial diesel and palm-oil biodiesel

Nanomaterials used as additives to diesel, biodiesel, and its blends have shown promising results in improving thermal efficiency and reducing pollutant emissions in compression ignition engines. However, the stability of dispersions has been noted in the literature as a primary challenge to the effective use of nanomaterials as fuel additives. Between nanomaterials used as additives to fuels are carbon nanotubes (CNTs). These carbonaceous materials have shown positive and negative results concerning engine performance and emissions, and the differences could be associated with the dispersion stability of the nanomaterials in the fuel. Therefore, there is still much uncertainty regarding the relationship between the stability of nanomaterial dispersion and the impact of nanofuels on engine performance. Specifically, the current literature lacks sufficient information regarding the impact of incorporating amide-functionalized carbon nanotubes (CNT) on the stability of diesel-biodiesel blends and their influence on particulate matter emissions in ICE. In this study CNT and amide-functionalized CNT were dispersed in Colombian commercial diesel (10 % vol. of palm oil biodiesel) and palm oil biodiesel, and its stability was evaluated. The most stable blends were used in a stationary Ignition Compression Engine (ICE) to evaluate the impact of the nanomaterials on thermal efficiency and pollutant emissions. Results show that it was not possible to disperse CNT in Colombian commercial diesel (10 % vol. of palm oil biodiesel and 90 % vol. of petroleum diesel) due to its high rate of agglomeration and sedimentation. In contrast, the opposite behavior was shown using biodiesel as a base fuel. An amide functionalization of the CNT process was carried out to generate a repulsion of CNT and improve its stability in commercial diesel fuel. Amide-functionalized carbon nanotubes (CNTF) were obtained using pristine CNT and Oleylamine as nitrogen functional group precursors. X-ray Photoelectron Spectroscopy confirmed the amide functional groups on the CNT surface, and a loss weight of 14 % was identified in the temperature range of 150–550 °C, indicating a high grade of functionalization. Functionalized and non-functionalized CNT were dispersed in Colombian commercial diesel and palm oil biodiesel using a concentration of 100 mg/L to evaluate the dispersion's colloidal stability. This stability was examined for three days by visual inspection and variation of the hydrodynamic diameter using dynamic light scattering. The most stable dispersions were prepared at two concentrations (50 and 100 mg/L) and used as fuels in a stationary compression ignition engine. Colloidal stability was enhanced when CNTF were dispersed in diesel compared to the unstable, pristine CNT dispersion. However, in biodiesel, the dispersion behavior of the CNT and CNTF was similar. Compared to diesel, the diesel-CNTF dispersion did not considerably improve the engine´s thermal performance at 6 kW, and only a minor gain was observed at 12 kW at a concentration of 100 mg/L. However, at 6 kW, they reduced particulate matter emissions by up to 39.8 %. In the case of biodiesel, utilizing both functionalized and non-functionalized carbon nanotubes as additives, the thermal efficiency was increased, and CO emissions decreased.

Production of biofuel from AD digestate waste and their combustion characteristics in a low-speed diesel engine

Anaerobic digestion biogas plants generate large amounts of digestate that cannot always be valorised as fertilizer. This study proposes an alternative use through pyrolysis of the digestate for the production of liquid fuels for compression ignition engines. The digestate pyrolysis oil (DPO) and two types of biodiesel were produced and mixed with different alcohols. A total of five blends of DPO, biodiesel and alcohol were prepared and characterized, showing that their acidity and viscosity were higher than for pure diesel, and their heating value was lower. Blends containing 60 % biodiesel, 20 % DPO, and 20 % butanol were then tested in an engine, showing that the maximum in-cylinder pressure and heat release rate were 4.6 % and 3 % lower, respectively, compared to diesel, and the engine thermal efficiency at full load was 6–8% lower. The nitric oxide and smoke emissions were 7 % and 40 % lower, respectively, but the carbon dioxide emissions were 7–10 % higher than with diesel. The blends showed retarded start of combustion by 1.5° crank angle, which delays the ignition by about 6.4 %. This study concludes that blends can be used as a fuel for agriculture and marine diesel engines, although their viscosity should be reduced by improving the pyrolysis conditions.

The improvements of a diesel engine fueled with renewable and sustainable diesel/n-butanol/polyoxymethylene dimethyl ethers blended fuels at high altitudes

Atmospheric conditions at high altitudes deteriorate combustion in the cylinder of compression ignition (CI) engines, severely degrading engine performance and increasing soot emissions. The use of oxygenated fuels as an alternative fuel to diesel is an effective solution to improve performance and reduce emissions of highland CI engines. Before optimizing a highland CI engine, it is necessary to determine the law of influence of oxygenated fuels on the performance and emission characteristics of the engines. This paper focuses on the effect of diesel/n-butanol/polyformaldehyde dimethyl ether blends on the combustion, performance, and emission characteristics of a CI engine at different simulated altitudes (0 m, 2000 m, 3000 m, and 4000 m). First, a three-dimensional computational fluid dynamics (3D-CFD) simulation model was developed and validated by experimental results. Second, the 3D-CFD model coupled with a chemical kinetic mechanism including 164 species and 643 reactions was used to simulate the combustion process in the cylinder under different operating conditions. The results showed that the high-altitude environment increased the cylinder temperature, peak heat release rate, ignition delay, soot emissions, HC emissions, and brake specific fuel consumption, and reduced BTE, and NOx emissions of the CI engine compared with the plains. At the same altitude, the use of n-butanol and PODE3 provided oxygen for in-cylinder combustion, which somewhat promoted more complete combustion in the cylinder, reduced HC and soot emissions and increased BTE. Although the use of oxygenated fuels in highland CI engines elevated NOx emissions, the problem could be solved by methods such as LTC and SCR. Overall, n-butanol and PODE3 are promising alternative fuels for highland CI engines, mitigating to some extent the problems of higher soot and HC emissions and lower BTE associated with high-altitude environments.

Evaluation of Ecological Parameters of a Compression Ignition Engine Fueled by Diesel Oil with an Eco Fuel Shot Liquid Catalyst

This article discusses the potential applications of the Fuel Shot liquid catalyst in compression ignition (CI) engines for reducing toxic substances in exhaust gases. Incorporating catalysts into fuel can optimize the combustion process, consequently reducing the emission of toxic substances into the atmosphere. Toxic compounds, such as nitrogen oxides, particulate matter, and hydrocarbons, adversely affect flora and fauna. Various methods are known for reducing their concentration in engine exhaust gases, one of which is the Fuel Shot liquid catalyst. The authors conducted experiments on a Fiat 1.3 JTD engine with a Common Rail system. The results indicate that the application of the liquid catalyst reduces the content of nitrogen oxides and hydrocarbons in the exhaust gases and slightly decreases fuel consumption. Additionally, investigations were carried out on the engine’s injection apparatus, which was fueled with modified fuel. The findings demonstrate that the fuel additive does not affect the wear of precision parts of fuel injectors and high-pressure pumps.

A sustainable model using RSM and MCDM techniques to evaluate performance and emission characteristics of a diesel engine fueled with diphenylamine antioxidant and CeO2 nanoparticle additive biodiesel blends

Overconsuming fossil fuels has worsened global warming and air pollution, requiring us to investigate alternate fuels for compression ignition engines. Biodiesel is a renewable fuel and environmentally favorable. Biodiesel's most significant disadvantage is increased nitrogen oxide (NOx) emissions. The intent of the present study was to examine the impact of antioxidant diphenylamine (DPA) and nanoparticle ceria (CeO2) additive inclusion in a B30 blend on engine performance and exhaust emission characteristics. For this study, diesel, Jatropha biodiesel (B30), 100 ppm of antioxidant diphenylamine (50 ppm) with ceria nanoparticle (50 ppm) is added to the B30 blend named as B30+DPA100 and antioxidant diphenylamine (50 ppm) with ceria nanoparticle (50 ppm) is added to the B30 blend named as B30+DPA50+CeO250 fuel blends has been used. A hybrid response surface methodology and multi-criteria decision-making techniques (entropy method, TOPSIS, and VIKOR) have been used to develop a sustainable model and find the optimal setting of input parameters in terms of ranking. From experimental findings, the inclusion of antioxidants (DPA) and nanoparticle (CeO2) at 50 ppm to B30 significantly reduced NOx emission. The brake-specific fuel consumption and NOx have been found reduced by 5.67% and 18.87%, respectively, for B30+DPA50+CeO250 as compared to B30. At the same time, brake thermal efficiency increased by 1.01%. The brake mean effective pressure and maximum cylinder pressure) have been found increased by 0.68% and reduced by 4.52%, respectively, for B30+DPA50+CeO250 as compared to B30. The alternative ranking of the input parameters has been found fuel injection pressure (300), compression ratio (17), and load (12) as Rank 1 for TOPSIS and VIKOR. Therefore, the B30+DPA50+CeO250 blend is appropriate for improving diesel engine performance and diminishing exhaust emissions.

The combined effect of hydrogen enrichment and exhaust gas recirculation on the combustion stability, performance and emissions of CI engine energized by algae biodiesel

The scarcity of fossil fuels, the rising cost of liquid fuels, and the wide pollution footprint of conventional fuels all motivate scientists to seek out new approaches. This experimental study aims to explore the performance and emissions of compression ignition (CI) engines by introducing hydrogen into a biodiesel blend derived from algae. According to this study, the superior thermal properties of hydrogen associated with algal biodiesel have a significant impact on the performance and emissions of dual-fuel engines. The effect of hydrogen substitution rates of 10.4, 21.6, 32.4, 43.2, and 54 g per hour (g/h) on pure algae biodiesel was investigated. In comparison to diesel, the algae biodiesel reduces unburned hydrocarbons (UHC) and carbon monoxide (CO) emissions by 4.1% and 8.82%, respectively, while nitrogen oxide (NOx) emissions increase by 18%. Diesel was found to have increased brake thermal efficiency (BTE) and decreased brake specific energy consumption (BSEC) compared to biodiesel. With the addition of pure biodiesel, the 43.2 g/h H2 substitution rate produces a maximum thermal efficiency of 1.92% and a 9.5% decrease in brake-specific energy consumption compared to diesel at maximum load. Compared to diesel, the emission attributes of UHC, CO, and smoke opacity decreased by about 45%, 48%, and 41%, respectively. However, NOx emissions increase by about 36% compared to diesel due to the higher flame temperature and carbon-free fuel of hydrogen and oxygenated biodiesel. The induction of 15% exhaust gas with B100 + 43.2 g/h H2 reduces NOx by about 31% in comparison to B100 + 43.2 g/h H2 without exhaust gas recirculation (EGR). This is primarily attributable to the high oxygen dilution and specific heat capacity of burned gases, which result in a decrease in peak cycle temperature. Compared to diesel, B100 + 43.2 g/h H2 increased the cylinder pressure and heat release rate by about 1.86 and 4.29%, respectively. As a result of its high energy density, hydrogen improves overall energy utilization and engine performance. Hydrogen's rapid flame speed and wide flammability range contribute to the efficient and complete combustion of the algae fueling the CI engine. As well as showing outstanding performance, dual fuel CI engines have the potential to significantly contribute to lowering emissions. Finally, it was determined that using algae biodiesel and exhaust gas recirculation with hydrogen substitution in diesel engines can significantly reduce emissions while increasing efficiency.

Impact of Hydrogen on Emission Reduction in a CI Engine when Fuelled with Blends of Diesel-Waste Cooking Biodiesel

Waste utilisation and emission of greenhouse gases are two of the world's most pressing challenges today. This study seeks to solve the problem generated by the disposal of Waste Cooking Oil (WCO) as a tiny step forward in contributing to the reduction of waste disposal. WCO has a high potential as a bio fuel for internal combustion engines, hence it was chosen for this investigation. WCO of 20% and diesel 80% is used. This study looks at the performance, combustion and emission parameters of a dual fuel compression ignition engine running on WCO biodiesel with a hydrogen additive at atmospheric condition. The parametric study include variation in engine load (0-18 kg) and hydrogen flow rate (3, 6, 9 LPM). The experiment was conducted on a four-stroke diesel (computerized), single cylinder, water cooled power at 5.2 kW at 1500rpm Kirloskar engine. From the experiment overall parametric variation of 35.38%, 34.06% and 32.37% of brake thermal efficiency was obtained and emission was observed. However, with increase of hydrogen flow rate resulted in increased engine performance, increase in CO, NOx and reduction in emission of UBHC and CO2.

Assessment and usability of Jatropha biodiesel blend with phenolic antioxidant to control NOx emissions of an unmodified diesel engine.

The excessive utilization of fossil fuels has worsened global warming and exacerbated the levels of air pollution in the environment, forcing us to consider alternative fuels for compression ignition engines. The current research aims to explore the possibilities of renewable fuels outperforming diesel fuel in terms of combustion, performance, and emission characteristics. Biodiesel is an environmentally friendly and renewable alternative fuel. The major drawback of biodiesel is the significant rise in nitrogen oxide (NOx) emissions. The main novelty and objective of this research is to investigate the performance and emission characteristics of variable compression ratio diesel engine using DPA antioxidant additive. For this investigation, diesel, Jatropha biodiesel (B30) and 100 ppm of phenolic antioxidant diphenylamine (DPA) blended with B30 have been used as fuel named B30+DPA100. From experimental outcomes, the inclusion of diphenylamine to B30 blend resulted in brake-specific fuel consumption (BSFC) and exhaust gas temperature (EGT) being reduced by 8.86% and 4.12%, respectively, compared to B30. Simultaneously, there was a 1.11% increase in brake thermal efficiency (BTHE). The B30+DPA100 fuel blend demonstrates effective control over NOx and other emissions. The emissions of NOx, carbon monoxide (CO), hydrocarbon (HC), and smoke from the B30+DPA100 blend have shown a reduction of 6.8%, 5.34%, 7.86%, and 15.67%, respectively, when compared to diesel. However, there has been an increase in carbon dioxide (CO2) by 7.8%. One notable advantage of the B30+DPA100 blend is the significant decrease in NOx emissions. Additionally, the cylinder pressure for B30+DPA100 has been lowered by 4.93% compared to B30. On the other hand, the net heat release rate (NHR) has experienced a 1.72% increase. The particle size of different elements present in the crankcase oil has been calculated by Zetasizer Nano. The analysis revealed varying particle sizes for different elements in the crankcase oil: aluminum (2.724 μm), chromium (2.78 μm), iron (2.423 μm), and lead (2.587 μm).

Investigation of performance, combustion and exhaust emission characteristics of a compression ignition engine fuelled with diesel-kerosene-ethanol-hydrogen strategies

The current investigation acmes the ascendancy of ethanol on the performance, combustion and exhaust emissions of adulterated diesel fuelled compression ignition engine. Diesel adulteration by kerosene results in an adverse effect on performances and carbon emissions of the engine, but significantly reduces oxides of nitrogen. A small amount of ethanol incorporation into the adulterated diesel avowedly improves the performance, combustion and exhaust emissions of the engine. To this end, the engine is further modified for injecting hydrogen to reveal the competency of five different strategies along with 85% diesel, 5% kerosene and 10% ethanol blended fuel in volumetric proportion. The small amount of hydrogen enrichment aids in the improvement of brake thermal efficiency (up to 3.2%), brake specific energy consumption (up to 3.1%), in-cylinder pressure, heat release rate, brake specific hydrocarbon (up to 50.1%), brake specific carbon monoxide (up to 50.5%) and brake specific particulate matter (up to 44.8%) emissions.

Experimental Investigation of Compression Ignition Engine Combustion, Performance, and Emission Characteristics of Ternary Blends with Higher Alcohols (1-Heptanol and n-Octanol)

Concerns about the depletion of petroleum reserves and rising pollution led researchers to search for alternate and environmentally compatible fuels for compression ignition engines. As an excellent alternative fuel additive to biodiesel–diesel blends, higher alcohol exhibits outstanding fuel properties (such as high energy content and cetane number) and can operate in diesel engines without requiring engine changes. This study focuses on investigating the ternary blends comprising higher alcohols, namely 1-heptanol and n-octanol, in hybrid biodiesel (animal fat oil–rice bran oil–cottonseed oil) and diesel on compression ignition engine characteristics. The performance, combustion, and emissions of a diesel engine fuelled with mono (D100), binary (B20), and ternary fuel blends (B20H10, B20H20, B20O10, and B20O20) were analysed at a constant engine speed of 1500 rpm. The test fuels met the American Society for Testing and Materials standards for fuel properties and exhibited stable behaviour during testing. Experimental results showed that at 100% load, the least brake-specific fuel consumptions for diesel fuel, B20, B20H10, B20H20, B20O10, and B20O20 were 254.1 g/kWh, 302.14 g/kWh, 281.25 g/kWh, 310.94 g/kWh, 292.8 g/kWh, and 313.80 g/kWh, respectively. Meanwhile, the maximum brake thermal efficiency values were obtained as 38.65%, 37.01%, 37.76%, 36.84%, 37.12%, and 36.38%, respectively. At 100% load, the peak heat release rates for diesel, B20, B20H10, B20H20, B20O10, and B20O20 were found to be 64.65 J/deg, 59.07 J/deg, 62.34 J/deg, 56.12 J/deg, 57.95 J/deg, and 51.9 J/deg, respectively. The addition of 1-heptanol and n-octanol as oxygenated additives into the ternary blend resulted in decreased carbon monoxide and unburned hydrocarbon emissions while increasing carbon dioxide and nitrous oxide emissions compared to diesel fuel. Overall, the study concludes that ternary blends with 1-heptanol and n-octanol as additives improve performance and combustion behaviour and reduce exhaust emissions compared to binary blends.

Investigation of the drop-in capabilities of a renewable 1-Octanol based E-fuel for heavy-duty engine applications

This article presents the results of an investigation of neat 1-Octanol and its blends with Diesel, which can be potential drop-in fuels for heavy-duty compression ignition engines. Fuel blends consisting of 10 %, 20 %, and 30 % 1-Octanol by volume in Diesel, including neat 1-Octanol, were investigated for ignition and combustion performances. The ignition behavior was assessed using a constant-volume combustion-chamber-based ignition tester. The experimental investigation was conducted on a heavy-duty single-cylinder engine by varying the combustion center. In addition, injection-rate shaping was performed to understand the effects of various injection-rate shapes, namely square, ramp, and boot rate shapes, on the performance of neat 1-Octanol.The ignition tester results indicated an increased ignition sensitivity of neat 1-Octanol towards the chamber pressure and temperature compared to that of Diesel. At an elevated chamber temperature (650 °C) and pressure (20 bar), the ignition delay of neat 1-Octanol approaches closer to that of Diesel. Engine experiments revealed an improved thermal efficiency with neat 1-Octanol and its blends by up to 1.2 %, owing to their improved mixture homogenization capabilities. Furthermore, neat 1-Octanol and its blend led to a drastic reduction in smoke and carbon monoxide. In addition, it results in the highest peak during the premixed heat release, and with a square injection-rate shape, an additional minor improvement in thermal efficiency was observed. The relative changes in carbon monoxide and hydrocarbon emissions between the injection-rate shapes were negligible. At higher load, the boot-rate shape results in lower NOx formation than the square-rate shape at an almost identical thermal efficiency. Overall, the 10 % 1-Octanol, 20 % 1-Octanol and 30 % 1-Octanol blends, which fulfill the Cetane number requirements for the given fuel norms, can be used as drop-in fuels, as they exhibit a comparable or even better performance than Diesel.

Effects of temperature and composition inhomogeneity on the ignition characteristics of NH3/H2 co-firing fuels under HCCI operating conditions

The application of ammonia (NH3) in combustion devices, such as internal combustion engines (ICEs), is expected to largely reduce the greenhouse gas (CO2) emission. NH3/H2 cofiring fuels in homogeneous charge compression ignition (HCCI) engines may provide a potential way to deal with zero carbon requirements. However, in HCCI engines, the ignition process needs to be moderated since the ignition is only controlled by the chemical kinetics of the fuel. Therefore, this study investigates the effects of temperature and composition stratification strategies on the auto-ignition characteristics of NH3/H2/air mixtures under HCCI engine operating conditions with direct numerical simulation (DNS). 12 cases with different stratification strategies have been set under turbulent conditions. The chemical kinetics of NH3/H2/air was verified with the laminar flame speeds and ignition delay times. Results show that the temperature stratification can reduce the peak value of heat release rate (HRR), advance the ignition time and extend the combustion duration. In this case, the chemical reaction front is dominated by the deflagration or flame propagation mode. However, in contrast, composition stratification shows very limited effect on the overall combustion process, which is similar to homogeneous ignition and denoted as the spontaneous ignition mode. When increasing the hydrogen content in the fuel, the ignition time is obviously advanced and the peak of HRR is slightly increased. Higher NO emission is also observed which is mainly due to the increase of O, H, and OH intermediates to enhance the fuel NO production. Temperature stratification degree can improve the ignition process under both negatively correlated or unrelated T-Φ fields. However, the improvement is more evident for unrelated T-Φ condition when increasing the stratification degree.

Effects of hydrogen and EGR on energy efficiency improvement with ultra low emissions in a common rail direct injection compression ignition engine fueled with dimethyl ether (DME) under HCCI mode

This study deals with enhancing the energy efficiency with ultra-low emissions and extending the operating range (maximum load limit) of dimethyl ether (DME) fueled homogeneous charge compression ignition (HCCI) engine using hydrogen and exhaust gas recirculation (EGR). In the neat DME mode, the possible maximum load limit with controlled auto-ignition (CAI) was found as 24% (BMEP of 1.67 bar). Beyond 24% load, the knocking was observed with an advanced combustion phase, and shortened combustion duration resulted in uncontrolled auto-ignition (UAI) combustion. The addition of EGR extended the maximum load limit to 52% (BMEP of 3.62 bar) (60% EGR). Near-zero levels of NOx, zero smoke, and marginal CO and HC emissions reduction were observed with the optimized EGR rate (35%). The hydrogen fuel addition along with DME at an optimized EGR rate resulted in combustion phase retardation with the elimination of the low-temperature reaction (LTR) region. The energy efficiency (EE) and indicated thermal efficiency (ITE) increased along with zero smoke emission, ultra-low NOx, CO, and HC, and lower CO2 emissions till 12% of hydrogen energy share (HES). Thus, the combined strategy of EGR and hydrogen could effectively extend the operating range with ultra-low emissions levels.

Synthesis of spirulina microalgae biodiesel, and experimental research of its effects on compression ignition engine responses with iron II-III oxide (Fe3O4) nanoparticle supplementation

The raw material from which biodiesel is produced, the pioneer of alternative fuels in compression ignition engines, has increased importance in recent years. Third-generation biodiesels, which do not harm the food chain and environment, have become popular in recent years. In this study, fuel mixtures were obtained by mixing biodiesel produced from spirulina microalgae, the third-generation biodiesel type, with diesel and iron II-III oxide (Fe3O4) at different concentrations. Microalgae biodiesel (MAB) was mixed with diesel at two different percentages (10% and 20%), and three diverse quantities of Fe3O4 (25, 50, and 75 ppm) were added to 20MAB80D. Since the effects of the fuel mixture containing 20% MAB on the engine response are more optimistic, nanoparticles were added to the fuel containing 20% MAB. These fuel blends were evaluated under various engine loads (from 25% to 100%) at a constant engine speed (1500 rpm), and a compression ratio (15.5:1). Brake thermal efficiency (BTHE) and brake mean effective pressure (BMEP) improved with the addition of both MAB and Fe3O4. Compared to diesel (D100), the highest increases were achieved with 20MAB80D75IO fuel, with an average of 28.64% and 13.18%, respectively. With the 20MAB80D, these increases averaged 12.85% and 3.85%, respectively. On the other hand, brake-specific fuel consumption (BSFC) response increased with MAB and decreased with Fe3O4. With 20MAB80D75IO fuel, it showed an average decrease of 19.02% compared to BSFC diesel. With the 20MAB80D, there was an average increase of 11.31%. MAB and Fe3O4 contributed to reducing carbon monoxide (CO) and hydrocarbon (HC) emissions, which are products of incomplete combustion. With 20MAB80D75IO fuel, an average of 24.21% and 57.36% reductions were achieved, respectively, compared to D100. With the 20MAB80D, there was an average of 20.14% and 22.62% reductions, respectively. Conversely, NOx produced by 20MAB80D75IO was 11.63% higher than D100, while NOx produced by 20MAB80D was 3.83% higher. In conclusion, the experimental data obtained using Fe3O4 nanoparticles added to improve engine responses by improving the properties of MAB produced as third-generation biofuels revealed that MAB would be an excellent alternative fuel and Fe3O4 was a suitable additive.

A Synergic Application of High-Oxygenated E-Fuels and New Bowl Designs for Low Soot Emissions: An Optical Analysis

Synthetic fuels significantly reduce pollutant emissions and the carbon footprint of ICE applications. Among these fuels, oxymethylene dimethyl ethers (OMEX) are an excellent candidate to entirely or partially replace conventional fuels in compression ignition (CI) engines due to their attractive properties. The very low soot particle formation tendency allows the decoupling of the soot-NOX trade-off in CI engines. In addition, innovative piston geometries have the potential to reduce soot formation inside the cylinder in the late combustion stage. This work aims to analyze the potential of combining OMEX with an innovative piston geometry to reduce soot formation inside the cylinder. In this way, several blends of OMEX-Diesel were tested using a radial-lips bowl geometry and a conventional reentrant bowl. Tests were conducted in an optically accessible engine under simulated EGR conditions, reducing the in-cylinder oxygen content. For this purpose, 2-colour pyrometry and high-speed excited state hydroxyl chemiluminescence techniques were applied to trace the in-cylinder soot formation and oxidation processes. The results confirm that increasing OMEX in Diesel improves the in-cylinder soot reduction under low oxygen conditions for both piston geometries. Moreover, using radial lips bowl geometry significantly improves the soot reduction, from 17% using neat Diesel to 70% less at the highest OMEX quantity studied in this paper.

Impact of titanium dioxide (TiO2) nanoparticles addition in Eichhornia Crassipes biodiesel used to fuel compression ignition engine at variable injection pressure

Power production through combustion of fuels plays a vital role in the progress of a nation. In liquid fuels, biodiesel has emerged as a potential replacement of fossil fuel. In this regard, the improvement of fuel properties or adjustment of the operating parameters can improve the efficiency and lower the emission for a biodiesel run diesel engine. In this regard, the current study focuses on the use of novel nano blended biodiesel, prepared by blending titanium dioxide nano particles along Eichhornia Crassipes biodiesel. Three different biodiesel blends are prepared having composition of titanium dioxide by 50 ppm, 100 ppm and 150 ppm which is tested in a four stroke, single cylinder, naturally aspirated water cooled diesel engine of 3.5 kW rated power for different loading conditions for performance, emission, and combustion evaluation. Further, at the same engine conditions, the biodiesel blend having 150 ppm of titanium dioxide is tested at fuel injection pressure of 220 bar. The findings suggests that the brake thermal efficiency improves and emissions lowers with the addition of nano particles at high fuel injection pressure. The maximum improvement of brake thermal efficiency of 1.01% in comparison to diesel mode has been found for nano blended biodiesel composition of 150 ppm of titanium dioxide at fuel injection pressure of 220 bar under full loading condition. For the same fuel injection pressure of 220 bar and same nano blended biodiesel composition, the hydrocarbon and carbon monoxide emission were found to minimum at 60% load.

Investigation on novel natural gas fueled homogeneous charge compression ignition engine based combined power and cooling system

A significant part of energy of fuel supplied is lost in internal combustion engines in the form of atmospheric discharge of engine exhaust gases which are considered as a big source of engine inefficiency and formation of pollutant emissions. To address this issue, a bottoming cycle combining the transcritical CO2 (T-CO2) refrigeration cycle and the supercritical CO2 (sCO2) power cycle is employed, aiming to produce cooling for food preservation by utilizing the exhaust heat of homogeneous charge compression ignition (HCCI) engine powering the refrigerated truck. The operative variables and their effect on thermal and exergetic efficiency of HCCI engine and the combined system are investigated. At the base case operative conditions, the thermal and exergy efficiencies of natural gas fueled HCCI engine are improved significantly from 48.69% to 61.28% and from 41.14% to 42.79%, respectively, after employing the sCO2 powered T-CO2 refrigeration cycle. Promotion of equivalence ratio from 0.3 to 0.9 enhances the thermal and exergy efficiencies of HCCI engine from 47.44% to 49.54% and from 40.14% to 42.12%, respectively. Increasing of engine speed from 1400 r.p.m to 2200 r.p.m provides marginal improvement in HCCI engine efficiencies but the efficiencies of combined cycle are significantly improved from 57.67% to 65.18% and from 40.64% to 45.06%, respectively. Finally, exergy analysis applied to determine the sources of non-idealities within the system revealed that out 361 kW (100%) fuel exergy supplied to the system, HCCI engine destroys 93.31 kW (25.85%), catalytic convertor destroys15.49 kW (4.29%), and the in-cylinder heat transfer losses and system exhaust losses are found as 35.72 kW (9.91%) and 16.61 kW (4.61%), respectively.

Efficacy of machine learning algorithms in estimating emissions in a dual fuel compression ignition engine operating on hydrogen and diesel

Emission created by combustion of fossil fuels are a major concern of the world for the past few decades. The stringent emission norms have impacted the automobile manufacturers to work on exhaust emissions and its impact. This research focused on using machine learning regression models to evaluate the efficacy of experimental results for a dual fuel compression ignition (CI) engine operating on hydrogen and diesel. In the present study, engine emissions were estimated using 29 regression algorithms. A total of 5 input data namely, concentration of hydrogen, engine load, diesel intake, speed and equivalence ratio were considered in the study to estimate various emissions like oxides of nitrogen (NOx), carbon dioxide (CO2), hydrocarbon (HC) and smoke. Correlation coefficient, mean absolute error, root mean squared error, relative absolute error and root relative squared error were adopted as the performance metrics in the present study. Amongst the algorithms considered, pace regression, radial basis function regressor, multilayer perceptron regressor and alternating model tree produced the highest correlation coefficient of 0.9985, 0.8958, 0.9950 and 0.9256 in estimating the engine emissions like CO2, smoke, NOx and HC respectively. Additionally, an attempt was made to establish an individual algorithm that can estimate all the emissions was identified as multilayer perceptron regressor with correlation coefficient values of 0.9977 (CO2), 0.9950 (NOx), 0.8501(smoke) and 0.8731(HC) respectively.