Pulse Frequency Modulation Research Articles

Surge Current Analysis and Reduction in LLC Resonant Converter With a New Hybrid Control Strategy of Pulse-Frequency Modulation and Phase-Shift Modulation

Surge Current Analysis and Reduction in LLC Resonant Converter With a New Hybrid Control Strategy of Pulse-Frequency Modulation and Phase-Shift Modulation

Quasi-distributed acoustic sensing based on optical path difference demodulation for high-frequency and large-amplitude using an optical fiber interferometer array.

The phase-sensitive optical time domain reflectometry scheme has attracted great research interest in distributed acoustic sensing (DAS) but suffers from a trade-off between the dynamic range and signal frequency. In this paper, an optical path difference (OPD) demodulation method is applied to an interferometer array composed of an ultra-weak fiber Bragg grating (UWFBG) array and an imbalanced Michelson interferometer to solve this problem. As far as we know, this is the first time that OPD demodulation has been applied to DAS. The UWFBG array is interrogated by a frequency-modulated pulse, and the acoustic signal sensed by the fiber between any two adjacent UWFBGs can be retrieved by demodulating the variation of residual OPD of the interferometer formed by them. The proposed method is analyzed theoretically and validated experimentally; compared with the phase demodulation method, a 100-times boost in bandwidth is achieved for a signal with an amplitude of 0.4 µε. Results also show that the proposed method offers increasing signal-to-noise ratios as the frequency increases.

State-space analysis of a continuous gravitational wave source with a pulsar timing array: inclusion of the pulsar terms

ABSTRACT Pulsar timing arrays (PTA) can detect continuous nanohertz gravitational waves (GW) emitted by individual supermassive black hole binaries. The data analysis procedure can be formulated within a time-domain, state-space framework, in which the radio timing observations are related to a temporal sequence of latent states, namely the intrinsic pulsar spin frequency. The achromatic wandering of the pulsar spin frequency is tracked using a Kalman filter concurrently with the pulse frequency modulation induced by a GW from a single source. The modulation is the sum of terms proportional to the GW strain at the Earth and at every pulsar in the array. Here, we generalize previous state-space formulations of the PTA problem to include the pulsar terms; that is, we copy the pulsar terms from traditional, non-state-space analyses over to the state-space framework. The performance of the generalized Kalman filter is tested using astrophysically representative software injections in Gaussian measurement noise. It is shown that including the pulsar terms corrects for previously identified biases in the parameter estimates (especially the sky position of the source) which also arise in traditional matched-filter analyses that exclude the pulsar terms. Additionally, including the pulsar terms decreases the minimum detectable strain by 14 per cent. Overall, the study verifies that the pulsar terms do not raise any special extra impediments for the state-space framework, beyond those studied in traditional analyses. The inspiral-driven evolution of the wave frequency at the Earth and at the retarded time at every pulsar in the array is also investigated.

Optically Delaying a Radio Frequency–Linear Frequency-Modulated (RF-LFM) Pulse Using Kerr Comb Carriers and Off-the-Shelf Concatenation of a Linearly Chirped Fiber Bragg Grating and a Chirped-and-Sampled Fiber Bragg Grating

We demonstrate a low latency delay of a radio frequency (RF)–linear frequency-modulated (LFM) pulse by modulating it onto optical carriers from a Kerr comb and sending the signal through a concatenation of off-the-shelf linearly chirped fiber Bragg gratings (LC-FBGs) and chirped-and-sampled FBG (CS-FBG). We characterize the frequency response and latency of the LC-FBG and CS-FBG. Then, experimentally, the LFM pulse performance is characterized by measuring the peak sidelobe level (PSL) at the output of the tunable delay system. The experiment, performed with an LFM pulse of 1 GHz bandwidth at a 10 GHz center frequency, shows a PSL better than 34.4 dB, attesting to the high quality of the buffer RF transfer function. Thus, the proposed optical memory buffer architecture, utilizing compact devices based on a Kerr comb and FBGs, offers several benefits for delaying LFM pulses, including (i) a larger tunable delay range, (ii) low latency, (iii) wide bandwidth, and (iv) high PSL.

Soft‐switching boundary and piecewise control of LLC converter with hybrid modulation

AbstractThe voltage gain range of LLC converter can be effectively broadened by using the hybrid modulation of phase‐shift modulation (PSM) and pulse frequency modulation (PFM). However, the harmonic of resonant tank increases dramatically in PSM mode, and the first harmonic approximation is no longer suitable for solving the voltage gain. Moreover, the conditions for soft switching in PSM mode are not clear. Meanwhile, the small‐signal models of the converter in different modulation modes are quite different, and it is difficult for a fixed controller to ensure a good dynamic performance of the converter in both modulation modes. To address above issues, a voltage gain modeling method of PSM mode LLC converter is proposed. By establishing the function between input current and resonant current, the voltage gain model of the converter is obtained according to the power conservation. Moreover, considering the parasitic capacitance charge and resonant current commutation time, the condition for soft switching is derived. Furthermore, a control strategy of LLC converter in hybrid modulation is proposed. The piecewise proportional integral (PI) controller is adopted, and the parameters of the controller are dynamically adjusted with the modulation mode, so that the converter has excellent dynamic performance in both modes. And the hysteresis control is used to ensure the stability of mode switching. An experimental prototype with 200–340 V input and 28 V/1 kW output was built based on gallium nitride (GaN) devices. The peak efficiency was 97.82%, and the power density was 65.76 w/in3.

Noncirculating current series resonant converter with pulse frequency modulation

SummaryIn this paper, an asymmetric pulse frequency modulation (APFM) is applied to the full‐bridge series resonant converter with a secondary LC resonant tank. Different from the traditional PFM, the upper and lower switches have complementary gate drivers and the lower switches have constant on time of half‐resonant period in this paper. Thanks to the resonant tank moved to the secondary side with the adopted APFM, the maximum magnetic flux density Bm of a high‐frequency transformer (HFT) is only concerned with the fixed resonant frequency rather than the variable switching frequency. Hence, the switching frequency can be widely regulated, as well as the voltage gain. Furthermore, the circulating current flowing back to the input voltage source in the traditional LC series resonant converter can be eliminated by the APFM, leading to a low resonant current peak value. The operation principles and characteristics of the adopted method are analyzed in detail. Finally, a 500 W/70–120 V to 300 V/21–180 kHz prototype is built, and the experimental results verified the theoretical analysis well.

A fully integrated charge pump with double-loop control and differentiator-based transient enhancer for neural stimulation applications

This paper proposes a fully integrated charge pump (CP) with a double-loop control and a differentiator-based transient enhancer (DTE) for high-voltage neural stimulation applications. The double-loop control includes a clock-supply-voltage (VCLK) modulation loop and a pulse-frequency modulation (PFM) loop. The VCLK modulation loop regulates the output voltage by adjusting VCLK while the PFM loop adjusts the operating frequency of the CP in accordance with the load current in order to improve power efficiency. The proposed CP combines the function of output voltage regulation and VCLK generation into a single unit, leading to significantly reduced circuit complexity. The proposed double-loop control is capable of dealing with different dc current requirements while the proposed DTE suppresses the undershoots and overshoots of the output voltage during load transients. The proposed CP has been simulated using a 0.18-μm triple-well CMOS process and occupies an area of 0.537 mm2. The post-layout simulation results show that it can provide a regulated 9-V output voltage from a 3.6-V input voltage with a peak power efficiency of 73.4 % at 2-mA load condition. The Monte-Carlo simulation demonstrates that the overshoot and undershoot of the output voltage are kept below 3 % when undergoing a 2-mA load transient.

Push-pull forward LLC resonant converter for low input voltage applications

A push-pull forward LLC resonant converter suitable for renewable energy power generation systems is proposed in this paper. The converter introduces the LLC resonant tank into the traditional push-pull forward converter and adopts pulse frequency modulation (PFM) control, which solves the problem of voltage spike of switches of the conventional push-pull converter, realizes the zero-voltage switching (ZVS) of the switches and has high conversion efficiency. In addition, the rectifier part of the structure adopts voltage doubling rectifier technology, which is beneficial to reduce the turn ratio and optimize the leakage inductance of the transformer. In this paper, the working principle of the converter is described in detail, and its gain characteristics and soft switching conditions are analyzed. Finally, an experimental prototype of 1 kW is built, and the output voltage of 380 V is achieved when the rated input voltage is 48–72 V, and its efficiency is up to 96.1 %.

P‐140: The Miniaturization of InGaN/GaN Micro‐LEDs for Micro‐Displays – Size Effects, Frequency Dispersion and Compact Modeling

InGaN/GaN green micro‐light‐emitting diode (micro‐LED, μLED) arrays with varying device sizes down to 4 μm are fabricated and characterized. The size effects on current‐voltage and capacitance‐voltage characteristics are analyzed showing minimal sidewall effects only at low bias. The influence of pulse modulation frequency on luminance is also characterized and the effect of diode negative capacitance is discussed. Subsequently, a universal and comprehensive compact model for μLEDs are built based on these findings, which covers the capacitance frequency dispersion and size scaling effects. This work reveals the significance of frequency in the display driving strategy and provides design enablement for μLED micro‐display applications including augmented/mixed reality (AR/MR).

Orbit-attitude coupled dynamics modeling and adaptive sliding mode control for detumbling large space debris

For non-cooperative large tumbling space debris, the use of detumbling techniques to reduce its angular velocity facilitates capturing and deorbiting operations. In our recent work, a new detumbling device combining three harpoons and a nanosatellite was designed. The device is released from the servicing satellite and attaches to the surface of the target. Then, the device's thrusters are actuated to reduce the target's angular velocity. In this paper, the dynamics and control issues involved in this strategy are further investigated. The collision model between the detumbling device and the target in the process of attachment is built based on the principle of momentum conservation. A high-precision orbit-attitude coupled dynamics model of the combined system during the detumbling mission is established, in which major external disturbances as well as inertial parameter variations due to the fuel consumption of the nanosatellite are taken into account. In addition, an adaptive sliding mode control scheme incorporating pulse-width pulse-frequency (PWPF) modulation is proposed for debris targets with parametric uncertainties and external disturbances. Finally, the effectiveness and robustness of the detumbling control scheme are demonstrated by numerical simulations. The results show that the detumbling device is capable of detumbling a large tumbling rocket upper stage within 4000s.

A Sparse Recovery Algorithm for Suppressing Multiple Linear Frequency Modulation Interference in the Synthetic Aperture Radar Image Domain.

In synthetic aperture radar (SAR) signal processing, compared with the raw data of level-0, level-1 SAR images are more readily accessible and available in larger quantities. However, an amount of level-1 images are affected by radio frequency interference (RFI), which typically originates from Linear Frequency Modulation (LFM) signals emitted by ground-based radars. Existing research on interference suppression in level-1 data has primarily focused on two methods: transforming SAR images into simulated echo data for interference suppression, or focusing interference in the frequency domain and applying notching filters to reduce interference energy. However, these methods overlook the effective utilization of the interference parameters or are confined to suppressing only one type of LFM interference at a time. In certain SAR images, multiple types of LFM interference manifest bright radiation artifacts that exhibit varying lengths along the range direction while remaining constant in the azimuth direction. It is necessary to suppress multiple LFM interference on SAR images when original echo data are unavailable. This article proposes a joint sparse recovery algorithm for interference suppression in the SAR image domain. In the SAR image domain, two-dimensional LFM interference typically exhibits differences in parameters such as frequency modulation rate and pulse width in the range direction, while maintaining consistency in the azimuth direction. Based on this observation, this article constructs a series of focusing operators for LFM interference in SAR images. These operators enable the sparse representation of dispersed LFM interference. Subsequently, an optimization model is developed that can effectively suppress multi-LFM interference and reduce image loss with the assistance of a regularization term in the image domain. Simulation experiments conducted in various scenarios validate the superior performance of the proposed method.

Step-adaptive accelerated demodulation algorithm for LFM-pulse-based distributed acoustic sensing

We propose a novel, to our knowledge, step-adaptive cross-correlation algorithm tailored for distributed acoustic sensing systems based on linear frequency modulation pulses, aiming for rapid demodulation. This algorithm adjusts its step length through an adaptive “successive refinement” search strategy, which greatly improves computational efficiency by reducing the number of cross-correlation computations. Experimental results have shown that the demodulation time can be reduced by approximately 15 times compared to the conventional method, while maintaining the same demodulation result.

A novel unloading strategy for solar sails using reflectivity control device

For near-Earth spacecraft, many environmental forces are utilized to unload reaction wheels. However, effects like magnetic force or atmospheric friction hardly exist in deep-space environments where solar sails operate. Thus, this paper proposes an unloading method that uses reflectivity control devices to generate Solar Radiation Pressure (SRP) torque to conduct the unloading process of solar sails operating in deep space. Firstly, the basic principles of the Reflectivity Control Device (RCD), satellite kinetic model, and Pulse Width Pulse Frequency (PWPF) modulator are given. Secondly, based on the torque envelope obtained by traversing all switch combinations of RCD, a novel strategy using a PWPF modulator is specially designed to achieve efficient unloading. In the end, we carry out numerical simulations and analyze the influence of different parameters, through which the validity of the proposed torque resolution scheme is demonstrated.

Magneto-acousto-electrical tomography using nonlinearly frequency-modulated ultrasound.

Objective. In this study, nonlinearly frequency-modulated (NLFM) ultrasound was applied to magneto-acousto-electrical tomography (MAET) to increase the dynamic range of detection.Approach. Generation of NLFM signals using window function method-based on the principle of stationary phase-and piecewise linear frequency modulation method-based on the genetic algorithm-was discussed. The MAET experiment systems using spike, linearly frequency-modulated (LFM), or NLFM pulse stimulation were constructed, and three groups of MAET experiments on saline agar phantom samples were carried out to verify the performance-respectively the sensitivity, the dynamic range, and the longitudinal resolution of detection-of MAET using NLFM ultrasound in comparison to that using LFM ultrasound. Based on the above experiments, a pork sample was imaged by ultrasound imaging method, spike MAET method, LFM MAET method, and NLFM MAET method, to compare the imaging accuracy.Main results. The experiment results showed that, through sacrificing very little main-lobe width of pulse compression or equivalently the longitudinal resolution, the MAET using NLFM ultrasound achieved higher signal-to-interference ratio (and therefore higher detection sensitivity), lower side-lobe levels of pulse compression (and therefore larger dynamic range of detection), and large anti-interference capability, compared to the MAET using LFM ultrasound.Significance. The applicability of the MAET using NLFM ultrasound was proved in circumferences where sensitivity and dynamic range of detection were mostly important and slightly lower longitudinal resolution of detection was acceptable. The study furthered the scheme of using coded ultrasound excitation toward the clinical application of MAET.

Design of a PWM/PFM hybrid modulation switching circuit for a four-switch buck-boost converter

Based on the application background of fuel cell, the conversion efficiency of the four-switch Buck-Boost converter using PWM (Pulse width modulation) is low at light load, and the conversion efficiency of the four-switch Buck-Boost converter using PFM (Pulse frequency modulation) is low at heavy load. A PWM/PFM hybrid modulation circuit using digital module to detect induced current and feedback voltage is presented. The circuit structure is simple and easy to integrate. It has the effect of fast selection according to inductance current and feedback voltage. The circuit works in PWM mode by default. After soft startup, PWM/PFM mode can be switched according to the load. Finally, simulation is carried out in FSBB converter. The experimental results show that the PWM/PFM hybrid modulation circuit has the function of multi-load lead switching mode and protection mechanism. Simulation in FSBB converter shows that the converter efficiency reaches 91.99% and the maximum load current is 2A. This helps improve the efficiency of Buck-Boost converters.

A Novel Single-Stage AC/DC Converter Integrated Interleaved DCM Boost PFC and LLC DC–DC With Reduced Bus Voltage

Due to the applied pulse frequency modulation (PFM) control and switch integration, single-stage Boost-LLC AC/DC converters suffer from high bus voltage which makes them difficult to operate for high voltage input. To solve this issue, a novel single-stage AC/DC Converter by incorporating the interleaved DCM boost cell and an LLC cell is proposed. Different from the existing topology, in the proposed converter, two capacitors employed for splitting the ac input voltage into two parts are placed before the rectifier bridge. Thus, the voltage across each PFC cell is halved and the bus voltage can be significantly reduced. Furthermore, two high-frequency diodes and one filter capacitor are omitted, which helps improve the zero-crossing distortion of the input current. More importantly, the circuit efficiency is thus increased. Hence, low bus voltage, low component count, and high efficiency are the main advantages of the proposed converter. Simulations and experimental results are presented to prove the above features of the proposed converter.

КЛИНИЧЕСКАЯ ОЦЕНКА РЕЗУЛЬТАТОВ ПОДГОТОВКИ К НЕСЪЁМНОМУ ПРОТЕЗИРОВАНИЮ ПОСЛЕ ПРОВЕДЕНИЯ ДЕНТАЛЬНОЙ РЕПЛАНТАЦИИ

After dental replantation surgery, it is necessary to take measures to promote the healing of the replanted tooth. In almost 100% of cases, clear signs of an acute inflammatory reaction of periodontal tissues are diagnosed. The effectiveness of combined preparation and pharmacological therapy in the prevention of the inflammatory process of periodontal tissues after tooth replantation was assessed. The condition of the periodontal mucosa and periodontal ligamentous apparatus in the area of supporting teeth was studied in preparation for orthopedic treatment of dentition defects, after the operation of their dental replantation. To solve the set tasks, research methods were used in the work: visual, palpation, instrumental, and statistical analysis of the research results. The patients are divided into two groups. Drug therapy was carried out using traditional medications: antiseptics, antibacterial drugs, biogenic stimulants, etc. Drug therapy used to treat patients in group 1 and group 2 was identical in the list of medications used. Patients of the 2nd group underwent complex treatment of inflammatory phenomena of the desmodontal structures and periodontal mucosa that occur after replantation surgery. In addition to pharmacological drugs, exposure to modulated red light was used using a Stomasvet physiotherapeutic device with a wavelength of 328 nm, a pulse modulation frequency of 76 Hz, and a radiation power of up to 30 mW. On the first day of the study, patients of group 1 and group 2 were characterized by hyperemia of the periodontal mucosa in the area of the replantation, swelling, and pain. By the fourth day, in patients of group 2, the inflammatory phenomena completely disappeared. In patients of group 1, inflammatory phenomena completely disappeared only by the eighth day. An integrated approach to the diagnosis and treatment of periodontal pathologies that arise after dental replantation will reduce the preparatory period for subsequent orthopedic correction of dentition defects, reduce the duration of patient adaptation to the structures used, and also increase the overall level of orthopedic treatment in dentistry.

A single-chip PFM-controlled LED driver with 0.5% illuminance variation

A high-efficiency LED driver with the pulse frequency modulation (PFM) control method to generate nearly consistent illuminance is demonstrated in this investigation. The illuminance consistency is achieved by sensing the feedback voltage and the temperature to modulate the on time of power devices such that automatic illuminance regulation is carried out. The recommended LED driver using the PFM control method is featured with an up-and-coming illuminance equalizer. Thus, it does not need any compensation circuit. Utilizing a 0.5-μm High Voltage CMOS process, the prototype has successfully fabricated, occupying 3.2 mm2 of chip area. The measurement outcomes of the chip demonstrate that the current error remains within 1% when the LED output current set at 20 mA. Moreover, the variation in illuminance is exceptionally low, measuring a mere 0.5%. Furthermore, the efficiency reaches 91% verified by the measurement results.

Phase-Shifting Adaptive LLC Resonant Converter with Reduced Turn-Off Loss in Wide Voltage Application

In this paper, a hybrid control method with adaptive phase-shifting modulation (PSM) and pulse-frequency modulation (PFM) is proposed to optimize the steady-state performance of an LLC resonant converter in wide voltage-gain range application. For the primary-side switches under the hybrid control method, zero-voltage switching (ZVS) performance is maintained over wide voltage-gain range and the turn-off loss is reduced; therefore, the converter reconciles wide voltage-gain range and high efficiency. Mode characteristics under different phase-shifting-angle-θ and switching-frequency-fs combinations is analyzed, and then the soft-switching characteristic is revealed. By introducing time domain analysis, the turn-on current of the primary-side switches is calculated, and thus the ZVS boundary of different θ and fs combinations is inferred. In addition, to acquire the optimum steady-state operation of the converter, the turn-off current is calculated; by making the converter work near to the minimum turn-off current operating point, the turn-off loss can be reduced greatly. With the principles of achieving ZVS performance and minimizing turn-off current, the phase-shifting angle θ of PSM is designed to be adaptive to the reference output voltage, no additional circuits are needed, and the two control degrees (θ and fs) are simplified to one (fs). The simulation and experiment are developed to verify the feasibility and effectiveness of the hybrid control method; the results show that ZVS performance is maintained at wide voltage-gain range and the turn-off current of the hybrid control method is reduced to that of the single PFM, and thus the turn-off loss is reduced. The efficiency comparison validates the fact that the hybrid control method has less power loss than single PSM and single PFM.

An LLC resonant converter with wide output range fixed frequency PWM control for PEV charging applications

PurposeThis study aims to regarding the application of traditional pulse frequency modulation control full-bridge LLC resonant converters in wide output voltage fields such as on-board chargers, there are issues with wide frequency adjustment ranges and low conversion efficiency.Design/methodology/approachTo address these issues, this paper proposes a fixed-frequency pulse width modulation (PWM) control strategy for a full-bridge LLC resonant converter, which adjusts the gain by adjusting the duty cycle of the switches. In the full-bridge LLC converter, the two switches of the lower bridge arm are controlled by a fixed-frequency and fixed duty cycle, with their switching frequency equal to the resonant frequency, whereas the two switches of the upper bridge arm are controlled by a fixed-frequency PWM to adjust the output voltage. The operation modes of the converter are analyzed in detail, and a mathematical model of the converter is established. The gain characteristics of the converter under the fixed-frequency PWM control strategy are deeply analyzed, and the conditions for implementing zero-voltage switching (ZVS) soft switching in the converter are also analyzed in detail. The use of fixed-frequency PWM control simplifies the design of resonant parameters, and the fixed-frequency control is conducive to the design of magnetic components.FindingsAccording to the fixed-frequency PWM control strategy proposed in this paper, the correctness of the control strategy is verified through simulation and the development and testing of a 500-W experimental prototype. Test results show that the primary side switches of the converter achieve ZVS and the secondary side rectifier diodes achieve zero-current switching, effectively reducing the switching losses of the converter. In addition, the control strategy reduces the reactive circulating current of the converter, and the peak efficiency of the experimental prototype can reach 95.2%.Originality/valueThe feasibility of the fixed-frequency PWM control strategy was verified through experiments, which has significant implications for improving the efficiency of the converter and simplifying the design of resonant parameters and magnetic components in wide output voltage fields such as on-board chargers.